Search Documents

By A. N. Mitinsky

Discussion of the paper of A. N. MITINSKY, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1697 to 1705. LAWFORD H. FRY, Burnham, Pa. (communication to the Secretary*). -The author assumes that the proportional limit and the elastic limit are coincident or very nearly so, and then further assumes that the stress corresponding to these two points is the least stress which if repeated will cause failure. The point is extremely interesting and it is to be regretted that the author did not quote experimental data to show the relation between the limit of repeated stress and the other properties of the material. The author's suggestion that a steel of poor quality may have a normal value for the yield point and tensile strength (see Fig. 2) and an abnormally low elastic limit, and that this will correspond to a low resistance to repeated stress, may account for a number of failures of axles in which the tensile tests show normal physical properties. If so and if a determination of the proportional limit would have eliminated the material before it was put into service, this determination will merit most earnest attention. It appears, however, that considerable further research is necessary before any definite conclusion as to the quality of a steel can be drawn from its proportional limit. Mr. Mitinsky's paper is extremely interesting and if it stimulates thought and work along the lines indicated, it may prove of considerable practical benefit. H. V. WILLE, Philadelphia, Pa.-The paper discusses the difference between the proportional limit, or elastic limit, and the yield point, and refers to the fact that much harm results from confusion of the terms yield point and elastic limit. Similar confusion has arisen in this country; the American-Society for Testing Materials does not even consider the elastic limit and proportional limit to be identical and recently adopted the following definitions:

Jan 12, 1915

By F. E. Buch

THE Smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The Smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter ,aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pct moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pct oxide copper. The predominating minerals are chalcocite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating k bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. GENERAL DESCRIPTION Flotation concentrate, containing to pct moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1947

By W. C. Lilliendahl, H. W. Highriter

THE method developed and used in this laboratory for the production of metallic uranium of such purity that it is ductile and can be cold-worked to fine wire or thin sheet by rolling has already been described1. It consists, briefly, in the electrolysis of potassium uranous fluoride (KUF6) in a molten bath composed of equal parts of sodium and calcium chlorides. The bath is contained in a graphite crucible, electrically heated to about 775° C., the crucible serving as the anode for electrolysis. The uranium deposits in finely divided form mixed with salts upon a molybdenum cathode suspended axially in the crucible. Upon completion of the electrolysis the cathode is removed and cooled, the deposit broken and leached to remove salts. The metal powder is washed with water and dilute acetic acid and dried in vacuo to reduce oxidation. Suitable amounts are then pressed into pellets and heated in vacuo by high-frequency induction, using a thoria crucible. The uranium melts and flows away from the pellet, leaving a shell, which is largely oxide. In general, this method produced a satisfactory metal, although at times the uranium was not ductile. The investigations recorded here were made to find the cause of this embrittlement. It was known that the metal generally contained carbon, derived from disintegration of the graphite crucible in which electrolysis is conducted, in amounts dependent upon the thoroughness of washing the metal powder. Accordingly, analyses of several samples, both ductile and brittle, were made by combustion and absorption of CO2 in Ascarite, using air instead of oxygen to reduce the temperature and rate of oxidation. Several of these metals were made with special precautions to reduce carbon content. The results show no relationship between ductility and carbon content in the range investigated (Table 1).

Jan 1, 1935

By R. C. Gifkins, A. Gittins

A. Gittins and R. C. Gifkins (University of Mel-houvne)— Evidence from somewhat similar experiments to those described in this paper has led us to the conclusion that possibility 2) of the four listed on p. 319 is a description of what happens in grain boundary sliding. That is, sliding is limited by accommodation deformation, it being necessary to the Continuance of sliding that this accommodation should take place. An example of such accommodation, though probably not the most important, is fold formation at triple points. The evidence and arguments for this point of view are set out in Refs. 14 to 16. In particular, an experiment with a lead bicrys-tall5 seems to support point 2) rather than 3). In creep of this specimen it was found that at least 90 pct of the extension of a zone 0.3 mm wide at the boundary was supplied by sliding at the boundary. The sliding was localized in a region at the boundary very much smaller than 0.3 mm, in fact, in a region too narrow to resolve optically. In poly crystalline Specimens&apos; there appears to be a surface effect, as found by Rachinger," but it appears that this may not manifest itself at low strains. "Low strains" means <10 pct for a Pb-TI alloy, <2.5 pct for magnesium or "Magnox" A12 alloy, or <40 pct for a 0 brass. Up to this extension the sliding, measured by the mean vertical step at boundaries, is proportional to extension. We are able to say this with some confidence, since the error bars on our points are statistically derived. Our results would lead us to think that the error bars on other work, including that of Mullendore and Grant, are much too large at low strains to show this

Jan 1, 1963

By Norman B. Pilling, George P. Halliwell

The effects of lead and tin up to maximum contents of about 0.1 per cent. each, in the presence of oxygen between 0.04 and 0.30 per cent., have been studied. Tin is retained efficiently in the oxidized condition, whereas lead is not. An approximate relation between the lead-oxygen and tin-oxygen contents is deduced which, if observed, permits the presence of these elements without detrimental effect. Excess of lead beyond this limit affects ductility and rolling properties adversely and an excess of tin correspondingly diminishes the conductivity. It is shown that copper carrying a combined lead and tin content of several hundredths per cent., yet fully equal in quality to electrolytic wirebar, may be produced under commercial conditions. Tin is not normally found in more than bare traces in current grades of American electrolytic copper, and lead is rarely found to more than a few thousandths per cent. In the electrolytic refining of copper these metals do not present great difficulty in separation and their presence in any considerable amount in copper that has been refined by this method need not be tolerated. On the other hand, the effect of these elements is not entirely academic, as a considerable tonnage of scrap copper liberally contaminated with them has been reclaimed by the fire-refining process into metal with a residual lead and tin content of several hundredths per cent., yet having excellent working properties and fully equal in quality to current grades of electrolytic wirebar. Such copper has been found entirely suitable for use in the manufacture of electrical apparatus. In the absence of oxygen, tin is known to depress the conductivity rapidly, and lead to impair ductility and the rolling properties, yet the effects of these metals on commercial grades of copper—i. e., copper containing from 0.03 to 0.10 per cent. of oxygen—apparently has not received systematic attention. Occasional reference is made to the fact that in the presence of oxygen lead may be tolerated, yet Addicks says,1 in regard to overpoling: "The unstable condition can be controlled by adding certain substances, notably lead, in small quantities, but as mere

Jan 1, 1926

By A. K. Mukherjee, J. E. Dorn

A modified Peierls model is Presented for the rationalization of the asymmetric plastic behavior of single crystals of bcc metals. The model assumes that the asymmetry of slip arises from a tendency toward asymnetric splitting of the a/2[111] screw dislocation. The approach differs from former theories however insofar as it assumes that the splitting is so minor ttut only the core energy is modified and that no real partial dislocations exist. As a consequence, the concepts of a line energy of a partial dislocation, interaction between partial dislocations, constriction energies, and stacking fault energies are not invoked. Instead the present analysis is based on a specialization of the Peierls mechanism which assumes an asymmetric dislocation core which is modified by the effective stress and permits cross slip. The theoretical predictions on the stress-temperature -strain rate and orientation relationship agree qualitatively with the limited experimental data that are currently available. Additional experimental work over wider ranges of conditions is suggested to provide more complete evaluation of the possible validity of this theory. RECENT experimental investigations on the low-temperature thermally activated deformation of bcc metals have confirmed the existence of several unique orientation effects. These will be described with the aid of the standard stereographic projection shown in Fig. 1. If slip were determined exclusively by crystal symmetry, the deformation characteristics would be symmetrical about X; = 0 and independent of whether the specimen were subjected to a tension or a compression stress, regardless of what combinations of slip planes might be operative. Experiments, however, reveal that neither of these symmetry based predictions are valid. A schematic representation of the commonly observed asymmetry of both the yield stress and the plane of slip is shown in Fig. 2. A reversal of the direction of stressing results in an inversion of the asvmmetric behavior. 1) Asymmetry bf Yielding. A detailed investigation on the asymmetric yielding in an Fe-2.7 pct Si alloy was repoEted by Tabka, Tikeuchi, and Furubayashi,1 Similar trends have been observed by Keh and Nakada on iron,&apos; Stein on molybdenum,3 Bowen, Christian, and Taylor4 on columbium, Sherwood, Guiu, Kim, and pratt5 on Ta, Cb, and Mo. The degree of asymmetry not only depends on the atomic number and alloying but, in all cases that have been examined, it also increases with a decrease in the test temperature. 2) Asymmetry of the Slip Plane. Asymmetric $I-~: curves of the type shown in Fig. 2 have been found for several Fe-Si alloys6-8,1 and columbium.4 There is general agre_ement that near X: = 30 deg slip occurs by the [111](211) mode so that ?1 = 30 deg. As X; decreases it appears that [111](211) to [111](101) cross slip takes place leading to slip band traces on intermediate planes. And as xi approaches 0 deg, sharp

Jan 1, 1970

By Joseph Daniels

The Fritz Engineering Laboratory was built under the direction of John Fritz, and presented by him to the University. A view of the building, looking east, is shown in Fig. 1. The building was started in 1909, and completed in 1910, although all of the equipment was not placed until later. Mr. Fritz gave his personal attention to the details of construction and equipment, and it was his custom to drive over every day to the University from his home in Bethlehem and spend some hours watching the work, offering suggestions, making changes, and planning new work. The result is a building and an equipment which embody his practical ideas. The laboratory structure is of the steel mill-building type, of light-colored brick, 91 by 114 ft., of which a section is shown in Fig. 2 and the floor-plan in Fig. 3. The steel frame carries the roof and traveling crane-way. Ample light has been provided by numerous windows in the side and end walls, in the clerestory, and by a skylight 84 ft. long and 9 ft. wide in the north roof. The main aisle of the building is 49 ft. 2 in. between centers of crane-columns, and has a clear height of 40 ft. The remainder of the width is taken up by two side aisles, 18 ft. high. The laboratory consists of four sections: (1) A general testing-section containing the testing-machinery, a small machine shop, and an office; (2) a cement-testing room; (3) a room for making and storing concrete test-specimens; (4) a hydraulic section.

Jan 1, 1912

By Warren B. Davis

Introduction If a subject this broad were to be covered in even moderate detail, it would require a set of books about the size of an encyclopedia. Since an acceptable length for this paper is a small fraction of one book, it will have to consist of a few samples of the subjects that I think are the most pertinent to World Fossil Fuel Economics. I plan to discuss the trends in world energy demand, particularly in the U. S. and Europe; the consumption patterns and cost patterns of oil, gas and coal; the prospects of synthetics; and some of the effects of government regulation of fuel economics. World Energy Demands Fig. 1 shows Free World energy consumption by principal areas for the period from 1950 to 1970 and a forecast for the period from 1970 to 1985. These figures include only the measurable forms of energy. An example of energy consumption that is not measured is the wood a peasant might cut in the forest and bum in a fireplace to heat his home. This omission probably is a very small part of the total. This forecast is not identical with that of Wayne E. Glenn (see Page 22), but the differences in total energy consumption are not significant. The U. S. consumption, which was 55 percent of the world total in 1950, had declined to 45 percent by 1970, and is expected to decline further to 38 percent by 1985. Western Europe has consumed 28 percent of the total from 1950 to 1970 and is expected to lose share slightly between 1970 and 1985. The most spectacular gainer is Japan, which increased consumption from 2.5 percent in 1950 to 7.5 percent in 1970, and is expected to reach nearly 17 percent by 1985. The over-all Free World total has grown from 62 quadrillion Btu (equivalent to 29 million B/D of crude oil) in 1950 to 151 quadrillion by 1970, an average growth rate of 4.5 percent/year. This total is expected to grow at a rate of 5 percent/year between now and 1985, reaching 315 quadrillion Btu (equivalent to nearly 150 million B/D). Fig. 2 shows which fuels supplied this energy between 1950 and 1970, and gives an estimate of how it will be supplied between 1970 and 1985.

Jan 1, 1971

By Shiro Ban-ya, John F. Elliott, John Chipman

The activity of carbon in Fe-C austenite at 1150°C has been determined for concentrations up to about 2.1 pct C using the equilibrium: C + COz = 2CO; equations have been derived expessing the activity as a function of carbon content on the basis of twelve mathematical models. Several of these represent the data satisfactorily. ACCURATE information on the thermodynamic properties of austenite in the binary system Fe-C is needed as a basis for studies of transformation and precipitation in steels of all sorts, alloy as well as plain carbon. The many attempts to approach this problem through statistical thermodynamics require sound and dependable experimental data in order to evaluate the several models which have been suggested. In this paper we are concerned with the experimental determination of the activity-composition relation in austenite at the temperature of its widest range of stability, approximately the eutectic temperature (1153°C). Accurate investigation of the activity of carbon in austenite may be said to have begun with the work of Dunwald and wagner.&apos; A more detailed study was carried out by R. P. smith2 on the two equilibria: More recent work on these two equilibria has been reviewed by Chipman,3 who pointed out the experimental hazards associated with studies of Eq. [I]. Studies of this reaction involve rather small values of the ratio these are susceptible to errors due to traces of moisture in the apparatus according to the reaction: Ellis, Davidson, and Bodsworth4 evaluated K, for their experimental temperatures and used desiccants to control water vapor pressure. While they were able in this way to obtain consistent values for K1 it cannot be said that all of the uncertainties of the method have been overcome. Results by both methods reported by Schurmann, Schmidt, and wagener5 appear to be consistent except at very low carbon content. Reaction [2] was employed in the experimental work reported here. It is to be recognized, however, that it is not applicable to projected studies of certain alloy steel compositions involving stable oxide-formers.

Jan 1, 1970

By Robert M. Grogan, Gill Montgomery

Fluorspar, the commercial name for fluorite, is a mineral composed of calcium fluoride, CaF,. Its valuable properties are due to its content of fluorine, and it is the principal commercial source of that element. The name is derived from the Latin word "fluere," to flow, because the mineral has a low melting point and is used in metallurgy as a flux. Cryolite is a sodium aluminum fluoride, Na,AlF,. It is a rare mineral which has been found in commercial quantities in only one place in the world, Greenland. Small amounts of it are shipped from stock in that country, and its place in industry has been taken over almost completely by synthetic cryolite. Because of the relative unimportance of cryolite, discussion of it has been relegated to a short section at the end of this chapter, which is principally concerned with fluorspar. History Fluorspar was used for ornamental purposes by the Greeks and Romans, who fashioned such things as vases, drinking cups, and table tops from it. Various peoples including the Chinese and the American Indians carved ornaments and figurines from large crystals. Its usefulness as a flux was known to Agricola (1564), who wrote about it in 1546. Mining began in England about 1775 and at various places in the United States during the period 1820 to 1840. Production became substantial following the development and widespread adoption of the basic open hearth method of making steel, in which fluorspar is used as a flux. After that, production and usage were stimulated by growth in the steel, aluminum, chemical, and ceramic industries and were accelerated by World Wars I and II. Fluorocarbons entered the picture in 193 1 and the use of anhydrous hydrogen fluoride (HF) as a catalyst in the manufacture of alkylate for high octane fuel blends began in 1942. The development of the froth flotation process in the late 1920s, a differential flotation scheme for separating fluorspar from galena, sphalerite, and common gangue minerals in the 1930s, and the application of heavy-media concentrating methods to the treatment of low grade ores in the 1940s were outstanding technological contributions that enabled increased production of fluorspar concentrates. In recent years the development of pelletizing and briquetting processes for making flotation concentrates into gravel-size particles for use in steel furnaces and the development of more efficient and selective flotation schemes for treating crude ores containing abundant dolomite and barite have been major improvements in the industry.

Jan 1, 1975

By V. A. Josendal, J. W. Wilson, B. B. Sandiford

Two radioactive tracers have been tested as a means of determining core saturation in multiphase flow studies. Cesium chloride was tried as a water-phase tracer, but complications in its use in low permeability cores resulted from sorption of cesium by the core or water-wet pads. IodoI3&apos;ben-zene proved very satisfactory as an oil-phase tracer. The synthesis of iodobenzene from the sodium iodide as received from Oak Ridge is simple and direct. The tracer is insoluble in water and there was no evidence of sorption by any of the core materials used. use of the method to determine saturation profiles during capillary and dynamic desaturations and relative permeability measurements on oil-water and oil-gas systems is described. Comparisons of the dynamic and capillary methods of relative permeability determination were made using the tracer to check core saturation and saturation distribution. Other experiments are also described in which mobility of the oil phase at various saturations was measured by displacing labeled oil by flowing inactive oil. Similar experiments were made using water labeled with cesium 134. INTRODUCTION To be fundamentally sound. any laboratory method of determining relative permeability must meet, among others, the following requirements: (1) the core saturation between the pressure taps must be uniform, and (2) there must be uniform pressure difference between the phases in the region between the pressure taps. In practice it may eventually be shown that appreciable departure from either or both of these conditions may be permitted without introducing sensible error. but the magnitude of such error remains to be established. There is need then for methods of saturation determina- tion which will determine the saturation profile in a core as well as the overall average saturation given by the gravimetric or material balance methods usually employed. Methods which have received consideration include resistivity, X-ray absorption, gamma ray absorption, neutron diffraction, and radioactive tracers. The resistivity method has use in the determination of profile, but needs checking by independent means.&apos; The X-ray method has been used successfully, but requires elaborate equipment and calibration.23 4 At present gamma ray absorption is practical only for very large cores. The neutron methodo does not appear adaptable to measurement of saturation variations in short cores since it is a scattering method. Russell, Morgan and Muskat&apos; employed radiovanadium in a study of the mobility of interstitial water. Coomber and Tiratsook used radioiodine as an oil-phase tracer and measured profiles in unconsolidated sand packs. ADVANTAGES OF RADIOACTIVITY METHOD A thorough discussion of the theory of radioactive tracers and the technique of using them to study the movement of fluids in sands is given by Coomber and Tiratsoos and need not be detailed here. The method requires less equipment than the X-ray method; the counting problem is similar, but the generation and regulation of the radiation, which is a major problem in the X-ray method, is not required in the radioactivity method. In the X-ray method it is customary to add up to 20 per cent of absorber, usually an iodine compound, to the phase to be labeled. while in the radioactivity method a mere trace is sufficient. A possible disadvantage of the radioactivity method is that a disproportionate amount of the activity comes from the portion of the core nearest the counter, whereas the X-ray gives a true average saturation in the region traversed by the beam. 011 the other hand, this characteristic of the radioactivity method renders it peculiarly adaptable to study of certain types of radial variations in saturation. As with the X-ray method, a tracer may be added to either the oil or water-phase. An oil-phase tracer is more generally useful. however. since it permits work on oil and gas in the

Jan 1, 1952

By Gust Bitsianes, Joseph H. M. Beaty

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Joseph H. M. Beaty, Gust Bitsianes

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Hjalmar W. Johnson

IT has long been accepted that blast-furnace practice varies to some degree with the coke used. While the qualities desirable in iron have been known for some time, the qualities in coke that produce such iron have not been established. There are no objective standards for blast-furnace coke, which is usually described in general terms, as good or bad. Many experienced operators believe that coke cannot be measured objectively except by using it in the furnace, noting the result, and labeling the coke according to furnace operations. This is admittedly unscientific, and besides is useless for the two main purposes for which a measure of coke quality is needed: (I) to produce the best possible coke from the coals and equipment on hand; (2) to test new coals and determine their value for blast-furnace coke. In seeking such an objective measure, much work has been done on tumbler tests, shatter tests, sizes of coke, porosity, specific gravity, reactivity or combustibility and other tests, but as yet very little has been published in which conclusive correlations have been established between such objective measures and furnace operation. In our study of the problem during the past 8 years we have developed no new measures of coke quality, but we have collected data that are presented here in the hope that they may assist in further work, so that at some future time there may be developed such positive measures. The purpose of this paper is to show that there are variations in coke and that such variations do influence the operation of blast furnaces. At the same time we must remember that there are variations in blast-furnace operation and it may be the blast furnace that is at fault. This correlation of coke properties with blast-furnace operation will be worked out in the following steps: I. Discussion of a period when a change in the coke resulted in an increase in efficiency on one furnace and a decrease in efficiency on another. 2. Adaptation of the inefficient furnace to the available coke so that normal efficiency was restored. 3. The use of radial distribution: a discussion of the effect of size of ore layer in adapting blast-furnace operation to the coke. 4. An example of a change in size of coke and the detrimental influence on the production of one furnace. 5. An example of a change in size of coke, together with manufacturing data, to show why it changed, the conclusion being that coke is a product with an optimum value. 6. Illustration of the fact that coke has different optimum values on two furnaces, with discussion on adaptation of operation so the optimum values will be the same. 7. Limitations of the use of screen tests as an objective measure of coke quality. 8. Importance of uniformity in coke. FUNCTIONS OF COKE AND QUALITIES REQUIRED TO PERFORM THESE FUNCTIONS Coke has three important functions in a blast furnace: (I) to furnish most of the

Jan 1, 1941

By J. L. Lamont, W. Crafts

Studies of the effect of composition of steel on hardenability by Grossmann,&apos; and as-quenched hardness by Field2 and by the authors, have made it possible to predict the results of quenching when the composition and cooling rate are known In order to extend the application of the hardenability calculation to the quenched and tempered condition in which steel is finally used, a survey has been made of the hardness changes caused by tempering. From this study a method has been developed for the prediction of hardness and tensile strength of steel in the tempered condition. The method of calculation was developed from Rockwell C hardness tests on quenched and tempered Jominy specimens and is expressed in Rockwell C hardness units. It is of an additive type in which the degree of softening from as-quenched hardness is estimated. Tem-pred properties may be calculated within about plus or minus 5 Rockwell C hardness or plus or minus 15,000 lb. per sq, in. tensile strength. This degree of accuracy is less than that necessary for the control of heat-treatment, but is adequate for the comparative evaluation and selection of alloy steels. The formula indicates that tempered hardness is primarily dependent on as-quenched hardness and, as in the hardening reaction, the progress of tempering is controlled mainly by the carbon content. Alloys tend to retard softening by a secondary hardening mechanism in which the alloy appears to migrate from ferrite to the carbide phase. The factors for the effects of alloys in tempering vary so much from the effects of alloys in hardening that different steels of equivalent hardenability may, after like heat-treatment, differ considerably in tensile strength. Procedure In developing the method for calculating tempered Rockwell C hardness, simple and complex steels were tested over a range from 0.08 to 0&apos;65 per cent carbon and up to 2.68 per cent manganese, 2.18 silicon, 3.50 chromium, 4.94 nickel, and 1.06 molybdenum. The steels were made as small induction-furnace heats at the Union Carbide and Carbon Research Laboratories, Inc&apos; The accuracy of the method was finally checked on a variety of carbon, low-alloy and high-alloy types of heat-treating steels produced under commercial conditions. The method was based on a study of tempered Jominy bars, and its validity was tested by correlation with the center hardness and tensile strength of oil-quenched and tempered bars from 1/2 to 4 in. in diameter. The method of calculation was derived from the differences in Rockwell C hardness between as-quenched and quenched and tempered Jominy specimens. Prenormalized Jominy hardenability speci-menS quenched from a normal temperature for austenitizatios were used to obtain a range of as-quenched Rockwell C

Jan 1, 1948

By W. Crafts, J. L. Lamont

Studies of the effect of composition of steel on hardenability by Grossmann,&apos; and as-quenched hardness by Field2 and by the authors, have made it possible to predict the results of quenching when the composition and cooling rate are known In order to extend the application of the hardenability calculation to the quenched and tempered condition in which steel is finally used, a survey has been made of the hardness changes caused by tempering. From this study a method has been developed for the prediction of hardness and tensile strength of steel in the tempered condition. The method of calculation was developed from Rockwell C hardness tests on quenched and tempered Jominy specimens and is expressed in Rockwell C hardness units. It is of an additive type in which the degree of softening from as-quenched hardness is estimated. Tem-pred properties may be calculated within about plus or minus 5 Rockwell C hardness or plus or minus 15,000 lb. per sq, in. tensile strength. This degree of accuracy is less than that necessary for the control of heat-treatment, but is adequate for the comparative evaluation and selection of alloy steels. The formula indicates that tempered hardness is primarily dependent on as-quenched hardness and, as in the hardening reaction, the progress of tempering is controlled mainly by the carbon content. Alloys tend to retard softening by a secondary hardening mechanism in which the alloy appears to migrate from ferrite to the carbide phase. The factors for the effects of alloys in tempering vary so much from the effects of alloys in hardening that different steels of equivalent hardenability may, after like heat-treatment, differ considerably in tensile strength. Procedure In developing the method for calculating tempered Rockwell C hardness, simple and complex steels were tested over a range from 0.08 to 0&apos;65 per cent carbon and up to 2.68 per cent manganese, 2.18 silicon, 3.50 chromium, 4.94 nickel, and 1.06 molybdenum. The steels were made as small induction-furnace heats at the Union Carbide and Carbon Research Laboratories, Inc&apos; The accuracy of the method was finally checked on a variety of carbon, low-alloy and high-alloy types of heat-treating steels produced under commercial conditions. The method was based on a study of tempered Jominy bars, and its validity was tested by correlation with the center hardness and tensile strength of oil-quenched and tempered bars from 1/2 to 4 in. in diameter. The method of calculation was derived from the differences in Rockwell C hardness between as-quenched and quenched and tempered Jominy specimens. Prenormalized Jominy hardenability speci-menS quenched from a normal temperature for austenitizatios were used to obtain a range of as-quenched Rockwell C

Jan 1, 1948

By Roswell H. Johnson

The principle of sliding or graduation in royalties is accomplished either by the block, period, cumulative, or class method. The block method calls for a very low royalty rate on all oil produced up to a certain amount. This amount would normally be that which is believed to suffice to repay the cost of the well. A higher rate would be charged after the well is making a profit. This method, common in many industries, is peculiarly inadaptable to any industry such as this where the productivity per day of the units gradually and inevitably decreases. This, for reasons given later, is because it forces an early abandonment of the well and so offends against conservation. In the period method, the royalty rate is changed by some definite amount when the well produces less than a specified quantity per day or other given unit of time. While simple to explain, it operates badly because a great deal is made to depend upon a small reduction in production, whereas the reduction as a matter of fact declines rather erratically owing to the exigency of lease management, connecting of tankage, and vagaries of the gaugers. These disadvantages are obviated by the cumulative method. In this method, all the production less than a certain amount per week has one rate of royalty, or none at all, and the oil produced in excess of that amount pays an additional rate of royalty. In the long run the calculation is probably no greater than with the period method, for simple tables will be published and printed in the oil papers that can be cut out, enabling quick readings to be made. Even without the table the calculation is easy with the few royalty rates, two or three, which would be used. In this method, the amount paid in royalty declines gradually, rather than suddenly as in the period method. The following reasons might be advanced for the adoption oi cumulative royalties: 1. To distribute the burden in accordance with the capacity to pay. This principle is a unique one in business, although familiar in taxation. This is because it does not distribute reward in proportion to efficiency.

Jan 1, 1916

By C. A. Czako

INTRODUCTION In recent decades sintering and pelletizing of finely divided materials have become the primary tonnage producing modes of agglomeration. This statement is especially true in the iron and steel industry and, to a lesser degree, in the nonferrous, chemical and non-metallic minerals processing industries. In every industry the main objectives in agglomerating fines are essentially the same, namely to convert ores, minerals and chemicals of undesirable fineness into agglomerates characterized by a size consistency desirable for subsequent use or processing. Depending on the type of agglomeration process selected and the conditions maintained during agglomeration, the physical process of increasing size is complemented by a number of other unit processes. These processes can occur simultaneously, consecutively or in an overlapping manner. Some of these additional unit processes are incidental to the agglomeration operation, but at the same time can be critical, depending upon the subsequent use of the product. Accordingly, during processing, conditions have to be controlled to either suppress or enhance the extent of completion of these unit processes. The purpose of this report is to review laboratory testing as the basis for engineering modern sintering and pelletizing plants. Considering that most typical applications are for the iron and steel industry, agglomeration of ferrous materials is reviewed and discussed. When these total processes are adapted to suit non- ferrous materials, chemicals, or non-metallic substances, the over- all approach remains the same; only the processing parameters are affected as necessitated by the different nature of the materials.

Jan 1, 1977

By John S. Johnson

THE purpose of this article is to describe several types of borehole lining in common use, and especially to offer a relatively new means of reducing the expense of maintaining boreholes where they are subjected to corrosive action of water flowing either inside or outside of their casing. In the Anthracite region of Pennsylvania, boreholes are used for many purposes, the principal ones being: openings between the surface and underground workings through which are passed steam, water and compressed-air lines, ropeways from surface hoists to underground rope haulages, conduits for electric power and signal lines, water-discharge lines from underground pumping stations, and inlets to mine workings for flushing material. LININGS FOR BOREHOLES The inadequacy of steel pipe for use in boreholes has long been recognized. Various substitute materials have been tried, including screw-joint cast-iron pipe (Fig. I). Cast-iron pipe, while very effective as a discharge line for acid water (mine water) being pumped to the surface, is not so effective when serving as a conduit for silt and crushed rock being flushed underground for filling mine voids. Terra cotta pipe (Fig. 2) has been used in boreholes, and lasts a long time if the glazed inner surface of the pipe remains intact. Its installation in a borehole is very difficult and is recommended only where it is certain that there will be no subsidence of the surrounding territory. Accessibility in order properly to join each section of the pipe is essential to a satisfactory job. In large water holes, where it is possible to lower a man into the hole for sealing the joints of the pipe, glazed terra cotta pipe has been used successfully for delivering mine water from pumps in the mines. For large holes used for flushing refuse into mine workings where the surface wash is shallow, standard paving brick have been used to form a tube through the wash to the bedrock. These brick are laid radially, backed by common brick and cobbles laid in cement. It is obvious that the shaft through the wash must be large enough to permit a man to work in it. The flushing material is carried through bare rock from the juncture at bedrock to the openings underground. This plan has been used, particularly where a cast-iron surface line is laid upon the surface to carry the flushing material from the breaker to the hole, and down the hole continuously, with no opening to the air at the top of the hole, thereby eliminating the necessity of an attendant at this point (Fig. 3). Another similar type of borehole lining is constructed of hexagonal pieces of vitrified brick (Fig. 4). This type requires a steel drive pipe through the surface wash large enough to provide a finished tube of the desired size surrounded by a brick wall about 4 in. thick. The special bricks are laid in cement, six to a circle, around a lubricated pipe used as a form, and lowered in sections inside the large drive pipe; the bottom section is seated in a socket drilled in the solid rock, having the same inside

Jan 1, 1941

By P. A. C. Wilson

Instantaneous outbursts of carbon dioxide in coal mines have occurred in Germany only in one part of the Waldenburg-Neurode mining district.&apos; This mining region comprises the northeastern fold of the "Innersudetian" coal basin. The basin (Fig. 1) is in the form of a geologic trough approximately 60 km. (37 miles) long and 30 to 35 km. (19 to 22 miles) broad and is enclosed on three sides by ancient truncated mountain ranges—the Riesengebirge, the Bober-Katzbachgebirge and the Eulenge-birge. Only the southeastern part of the trough is not enclosed by mountains of older rock formation. The floor of the basin before the building up of the coal measures was formed on the western, northwestern and northeastern borders by the material from Archean rocks (gneiss and mica schists); in the northern part over this was deposited the Silurian formation. The carboniferous period is represented both by the Lower ("kulm") and Upper Carboniferous, with an unconformity between the stages; that is, the kulm was tilted up and partly eroded before the Upper Carboniferous was deposited. The kulm is a salt-water formation (with marine fauna) but Upper Carboniferous rocks are nonsaline water deposits, with fresh-water flora only. The Lower Silesian coal measures were thus formed in a lime basin fed by the running water coming down from the mountains. As already indicated, the bottom series of the Upper Carboniferous formation, termed "Waldenburg strata" were laid down unconformably on the Lower Carboniferous. Over the Waldenburg strata there are the "Weisstein strata," an intermediate barren stage without coal beds, 400 to 500 m. (1300 to 1600 ft.) thick. Another unconformity followed, which is overlain by the &apos;(Saarbrucken" series, which contain the upper coal measures, and the (&apos;Ottweil" strata. In the last named, it is only on the southwestern fold that beds of coal are developed.

Jan 1, 1931