Search Documents

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By A. P. Watts

FOREWORD THE problem of concentrating the disseminated lead ore of southeast Missouri is extremely simple. The economic mineral is galena and the gangue is dolomite. The ore assays from 4 to .6 per cent. lead, 80 per cent. of which is recovered in a 70 per cent. concentrate.. The ore is crushed through 10 mm. and sized on 2 mm.; the oversize is jigged, while the undersize is tabled, and the slime treated by flotation. The district is the largest lead producer in the world, the output of metallic lead for the year 1915 being 183,906 tons. Over 20,000 tons of ore a day is being treated. The management of the different properties is progressive and always open to suggestion. The fact; however, must not be lost sight of, that the problem in the district is peculiar, as the average ore contains but 80 to 120 lb. of a metal normally selling at about 4c. per lb. The low price of the metal limits the treatment system to one of low cost. An elaborate treatment is neither logical nor advisable. An engineer first visiting the district may consider that the method of treatment could be improved

Jan 10, 1917

By M. F. Trice

Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By M. F. Trice

Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By R. S. Shoemaker, F. W. McQuiston

CARLIN GOLD MINING COMPANY 1974 Operating Data to October MINE LOCATION: 40 miles from Elko, Nevada ORE DESCRIPTION: Gold with minor amounts of mercury occurring in siltstone and carboniferous limey shales. TYPE OF MINE: Open pit ORE HAULAGE TO MILL: By trucks up to a distance of 12 mi1es MILLING CAPACITY: 2500 tons per day ORE GRADE: 0.20 oz per ton oxide ore 0.25 oz per ton carbon type ore PRODUCTS: Gold bullion 993 fineness, by product quicksilver RECOVERIES: Oxide ore 887'0 Carbon ore 83% POWER FOR GRINDING: 7 Kwh/T POWER, other than grinding: 14 Kwh/T WATER SUPPLY: Pumped from wells 2- 112 miles through 13,000 ft of 8" buried pipe 6 ft underground. Consumption 0.60 tons of new water per ton of mill feed. TAILINGS: By 10" woodstave pipe a distance of 2500 ft to mine waste filled dam. RUNNING TIME: 10 ft x 10 ft mill on oxide ore, 98% 7 ft x 8 ft mill on carbon ore, 937'0 Principal causes of lost time, power outages and problems of feeding gaseous chlorine to carbon ore agitators. LABOR, TONSIMAN SHIFT: See detailed data sheet ILL BUILDING DESCRIPTION: Framed structural steel with sandwich type walls of marine plywood, then packaged pre - fabricated insulation and outer sheeting of galvanized corrugated steel.

Jan 1, 1975

By David A. Thomas, John F. Peck

Fibrous microstructures and their development have been studied by metallography and by hardness and quantitative metallographic measurements. Thin, curved grains were observed in transverse sections of commercial tungsten wire and were developed in laboratory-drawn iron wire at reductions greater than about 70 pct. The unusual grain shapes are attributed to the nonuniform mode of deformation of the grains associated with the characteristic [I101 preferred orientation that develops in bcc metals during drawing. Transverse sections of heavily swaged iron wire showed a ospiral nebulao structure that appears to result from the elliptical shape of the cross section of the swaging dies and their rotary motion. Hardness and quantitative metallographic results show unusual trends that parallel the changes in microstructure. Other phenomena are considwed in light of the results, including the strength of fine wires of bcc metals, ocylindricalo textures, and the ductility of fibrous tungsten. 1 HE microstructure of tungsten wire in a longitudinal section shows grains highly elongated in the working direction, giving the appearance of a bundle of parallel fibers, Fig. l(a). Wires of tungsten and other bcc metals show a pronounced preferred orientation in which a [I101 direction is parallel to the wire axis.l The microstructure and texture of tungsten develop during warm working (working above room temperature but below the recrystallization temperature) into wire by swaging and drawing. Fibrous tungsten so produced has limited but useful room-temperature ductility, whereas annealed tungsten is brittle at room temperature. During an investigation of the effect of recovery annealing on the substructure of commerical 0.030 in. diam tungsten wire, it was found that transverse sections of the as-received material showed thin, curved grains, Fig. 1(b), instead of the expected equiaxed grains. The fact that Figs. l(a) and (b) show different sections of the same material at the same magnification is at first disconcerting, because the long dimension of the curved grains in the transverse section is several times the average fiber width in the longitudinal section. However, a longitudinal section cuts most of the curved grains across their narrow dimension, giving the appearance of a multitude of narrow fibers. On the other hand, the plane of a longitudinal section occasionally includes a long dimension of a curved grain, resulting in a broad ofibero, such as A in Fig. l(a). EXPERIMENTS AND RESULTS To investigate the origin of fibrous microstructures and particularly the unusual transverse-section structure of tungsten, rods of iron (also bcc) were drawn and swaged in the laboratory. One rod of annealed Ferrovac E was drawn in six steps to a total reduction in area of 87 pct (0.10 to 0.036 in. diam), and a second rod was swaged to the same reduction, using approximately the same reduction steps. Longitudinal and transverse sections of the swaged and drawn iron wires are shown in Fig. 2, for reductions in area of 39, 73, and 87 pct. A fibrous microstructure in longitudinal section is first evident at 73 pct reduction, and it is further developed at 87 pct reduction. The grains in transverse section remain equiaxed until about 73 pct reduction, when they become somewhat elongated and curved. At 87 pct reduction, the drawn wire shows thin, curved grains in the transverse section, similar to those observed in tungsten. The transverse sections of the iron wires swaged 83 and 87 pct reduction in area show the striking ospiral nebulao structure in Fig. 2(d). This struc-

Jan 1, 1962

By J. M. Hassler

NOWHERE can there be found a more misleading statement than the old one that "Iron can be manufactured cheaper in the South." During the past decade ironmakers and users of iron have heard varied and sundry stories of the wonderful resources of the Birmingham district, including abundant ore and coal fields, cheap labor, a wonderful climate and similar industrial Utopian statements. Birmingham represents the major portion of the iron business in the South, acid as Birmingham fares so goes the iron business of the South. The intent of this paper is to shed some light on the actual conditions surrounding ironmaking in the South, especially in the Birmingham, or North Alabama, district. By a presentation of facts it is desired to point out that the "cheap iron" of the industrial South is a thing of the past, primarily because of increased labor cost and because labor is radically different in performance to what it was years ago. Also, because most of the raw materials needed in ironmaking that would be classed better than inferior are gone.

Jan 1, 1937

By Maynard H. Jameson

Earlier investigations of the potential-drop-ratio method of electrical prospecting have indicated that under suitable conditions this method is well adapted to the location of formation boundaries in stratified ground. A description of this development was given several years ago by H. Lundberg and Th. Zuschlag.l The curves published by these authors for the potential-drop-ratio variation above a horizontal contact indicated a definite relation of the position of the curve peak to the depth of the interface. The theory underlying this relation was subsequently studied by Z. Mitera in greater detail,' and the theoretical deductions were compared with the results of tank experiments. The investigations available at this writing were confined to studies of horizontal formation boundaries. It is the purpose of this paper to extend the scope of the previous work to the problem of dipping layers. Theory Consider the case of three media of different resistivities, whose interfaces are not parallel. If a point-source is located in one of these interfaces, its images do not lie in a straight line, but on the circumference of a circle whose center is at the hypothetical junction of the interfaces. R. F. Aldredgea determined the relation that exists between the degrees of dip of the two interfaces and the distances between the various images and the point for which the potential is to be found. As seen in Fig. I, three media of resistivities PO, p1, and p2 are involved, and the source I is located at the interface of the media Coo) and (p1). The perpendicular depth of the lower interface is h, 0 is the dip, R is the distance between source I and potential point P, and r is the distance between the images and that point. To distinguish between images lying above the ground interface and those below, the notation "odd" and "even" images will be employed; images below the ground interface will be termed "odd" and those above "even." The following relations govern the distances between either kind of images and the potential point: EvEn Odd Ta — R r1 - [rl] - [RS + 4h(h + R sin 01½ r, = [r] =. [R1 + 4h cos 0)2(h + -R sin 0)1½ ri - [r3] ={r3} [R* + 4h(4 cos2 0 - i)1 (h + R sin 0)l½ r4 = [r4] = [R2 + 4h(4 cos $ cos 30)1 (h + R sin 0)]½ r, — [r4] - [R2 + 4h(4 cos9 R cos 20 + cos 48)2 (h + R sin 01½ I RI + 4h[2 cos 30(4 cos2 0 - I)12 (h + R sin 8)1 ½ rn - [r4] - [R2 + 4hlf(cOs 0)18(h + R sin R)l½ As previously pointed out, the images of the source are on the circumference of a circle. If the angle of dip is 0, the angle measured from the horizontal to the first image is 28; to the second image it is 48, and so on. Since the limit of the reflecting interface is at its outcrop, the last possible

Jan 1, 1946

By Maynard H. Jameson

Earlier investigations of the potential-drop-ratio method of electrical prospecting have indicated that under suitable conditions this method is well adapted to the location of formation boundaries in stratified ground. A description of this development was given several years ago by H. Lundberg and Th. Zuschlag.l The curves published by these authors for the potential-drop-ratio variation above a horizontal contact indicated a definite relation of the position of the curve peak to the depth of the interface. The theory underlying this relation was subsequently studied by Z. Mitera in greater detail,' and the theoretical deductions were compared with the results of tank experiments. The investigations available at this writing were confined to studies of horizontal formation boundaries. It is the purpose of this paper to extend the scope of the previous work to the problem of dipping layers. Theory Consider the case of three media of different resistivities, whose interfaces are not parallel. If a point-source is located in one of these interfaces, its images do not lie in a straight line, but on the circumference of a circle whose center is at the hypothetical junction of the interfaces. R. F. Aldredgea determined the relation that exists between the degrees of dip of the two interfaces and the distances between the various images and the point for which the potential is to be found. As seen in Fig. I, three media of resistivities PO, p1, and p2 are involved, and the source I is located at the interface of the media Coo) and (p1). The perpendicular depth of the lower interface is h, 0 is the dip, R is the distance between source I and potential point P, and r is the distance between the images and that point. To distinguish between images lying above the ground interface and those below, the notation "odd" and "even" images will be employed; images below the ground interface will be termed "odd" and those above "even." The following relations govern the distances between either kind of images and the potential point: EvEn Odd Ta — R r1 - [rl] - [RS + 4h(h + R sin 01½ r, = [r] =. [R1 + 4h cos 0)2(h + -R sin 0)1½ ri - [r3] ={r3} [R* + 4h(4 cos2 0 - i)1 (h + R sin 0)l½ r4 = [r4] = [R2 + 4h(4 cos $ cos 30)1 (h + R sin 0)]½ r, — [r4] - [R2 + 4h(4 cos9 R cos 20 + cos 48)2 (h + R sin 01½ I RI + 4h[2 cos 30(4 cos2 0 - I)12 (h + R sin 8)1 ½ rn - [r4] - [R2 + 4hlf(cOs 0)18(h + R sin R)l½ As previously pointed out, the images of the source are on the circumference of a circle. If the angle of dip is 0, the angle measured from the horizontal to the first image is 28; to the second image it is 48, and so on. Since the limit of the reflecting interface is at its outcrop, the last possible

Jan 1, 1946

By Homer W. Riley

ANTHRACITE SMALL power-driven, toothed, cast-iron rolls were used first to break anthracite in 1844. Prior to that time, men with hammers, who stood on perforated cast-iron plates, broke the large lumps into commercial sizes. In order to convert run-of-mine into the various sizes required by the anthracite industry, about 20 million tons must be broken, annually, into smaller sizes. This phase of anthracite preparation is of major importance, because the degradation accompanying reduction in coal sizes should be kept at a minimum. The exclusive use of toothed rolls for that purpose indicates that comminution by rolls is the best solution of the problem. Many improvements have been made in tooth design, but the most important was a reduction of the peripheral speed of the rolls from 1000 to 300 ft. per minute. The higher speed was based upon and approximated the velocity of a falling piece of coal when it entered the rolls, Exhaustive roll tests at the slower speed showed that the same size reduction could be affected with less degradation. The adoption, therefore, of slow-speed, compound geared rolls, especially for breaking the larger sizes, became quite general after 1912. A high-speed roll is shown in Fig. 1 and a slow-speed roll in Fig. 2. Anthracite Crushing Problems.-Crushing anthracite presents the problem of selecting a series of rolls that will produce the greatest percentage of the prepared sizes of nut and over. The size distributions to be expected are shown in Table 1. Coal breaking and crushing practices in anthracite breakers involve the use of equipment for comminuting the following classes of material: 1. Run-of-mine-plus 6 ½ -in. coal. 2. Sized coal-steamboat, broken, egg, stove, nut, and pea. 3. Flat coal--coal that is flat and hence not suitable for the market. 4. Bone--a piece of laminated coal and slate, crushed for the purpose of reclaiming the coal. 5. Breaker refuse, reduced to a size suitable for flushing into a mine for back-filling purposes.

Jan 1, 1950

By Frederick N. Rhines, William A. Anderson

The investigations of Wymanl have demonstrated that copper deoxidized with several of the commonly used agents that confer immunily to ordinary hydrogen em-brittlement can still be embrittled if it is annealed alternately under oxidizing and reducing conditions. During the oxidizing cycle, oxygen diffuses into the copper and frequently deposits a subscale composed of the oxide of the residual deoxidizing agent. Upon subsequent reduction with hot hydrogen, the copper becomes ruptured along the grain boundaries to a depth sharply limited by the previous penetration of oxygen as delineated by the inner boundary of the subscale. Obviously the sensitivity to this kind of hydrogen embrittlement is engendered by the introduction of oxygen during the oxidizing anneal, but beyond this the mechanism of the process, and hence the controlling factors, remain obscure. There are several possibilities: (I) oxygen dissolved in the copper matrix of the subscale may, upon cooling prior to the hydrogen anneal, precipitate as cuprous oxide which is subsequently reduced by hydrogen as in the familiar case of hydrogen embrittlement; (2) oxygen in solid solution in copper may itself confer susceptibility to embrittlement by hydrogen; (3) the normally refractory oxides such as those of aluminum, silicon and titanium may themselves be reduced by hydrogen when in contact with copper; or (4) the precipitated oxides of the subscale may be complex compounds such, perhaps, as SiO2.Cu2O, which are partially reduced by hydrogen. These possibilities have been examined, and it has been concluded that the first three and possibly the fourth are operative collectively or individually under more or less predictable conditions. Effect OF Precipitated Cuprous Oxide and Dissolved Oxygen The literature provides no definite proof that oxygen in solid solution in copper can confer susceptibility to hydrogen embrittlement; indeed, the research of Leiter2 seemed to indicate the opposite—that to produce the effect, cuprous oxide must be present in massive form and in a more or less continuous network along the grain boundaries. To test this point, pure copper has been annealed in hydrogen under conditions designed to ensure the presence in various samples of: (I) precipitated cuprous oxide, (2) dissolved oxygen only, and (3) no oxygen in any form. Very pure copper" said to contain no oxygen and no spectro-scopically detectable traces of any other element (that is, no individual detectable impurity in quantity greater than 0.0001 per cent) was used. Strips of this material cold.-rolled 75 per cent to 1/8 in. in thickness were subjected to the following treatments, the results of which are noted:

Jan 1, 1941

By Frederick N. Rhines, William A. Anderson

The investigations of Wymanl have demonstrated that copper deoxidized with several of the commonly used agents that confer immunily to ordinary hydrogen em-brittlement can still be embrittled if it is annealed alternately under oxidizing and reducing conditions. During the oxidizing cycle, oxygen diffuses into the copper and frequently deposits a subscale composed of the oxide of the residual deoxidizing agent. Upon subsequent reduction with hot hydrogen, the copper becomes ruptured along the grain boundaries to a depth sharply limited by the previous penetration of oxygen as delineated by the inner boundary of the subscale. Obviously the sensitivity to this kind of hydrogen embrittlement is engendered by the introduction of oxygen during the oxidizing anneal, but beyond this the mechanism of the process, and hence the controlling factors, remain obscure. There are several possibilities: (I) oxygen dissolved in the copper matrix of the subscale may, upon cooling prior to the hydrogen anneal, precipitate as cuprous oxide which is subsequently reduced by hydrogen as in the familiar case of hydrogen embrittlement; (2) oxygen in solid solution in copper may itself confer susceptibility to embrittlement by hydrogen; (3) the normally refractory oxides such as those of aluminum, silicon and titanium may themselves be reduced by hydrogen when in contact with copper; or (4) the precipitated oxides of the subscale may be complex compounds such, perhaps, as SiO2.Cu2O, which are partially reduced by hydrogen. These possibilities have been examined, and it has been concluded that the first three and possibly the fourth are operative collectively or individually under more or less predictable conditions. Effect OF Precipitated Cuprous Oxide and Dissolved Oxygen The literature provides no definite proof that oxygen in solid solution in copper can confer susceptibility to hydrogen embrittlement; indeed, the research of Leiter2 seemed to indicate the opposite—that to produce the effect, cuprous oxide must be present in massive form and in a more or less continuous network along the grain boundaries. To test this point, pure copper has been annealed in hydrogen under conditions designed to ensure the presence in various samples of: (I) precipitated cuprous oxide, (2) dissolved oxygen only, and (3) no oxygen in any form. Very pure copper" said to contain no oxygen and no spectro-scopically detectable traces of any other element (that is, no individual detectable impurity in quantity greater than 0.0001 per cent) was used. Strips of this material cold.-rolled 75 per cent to 1/8 in. in thickness were subjected to the following treatments, the results of which are noted:

Jan 1, 1941

By Haydn H. Murray, Sam H. Patterson

The term clay is somewhat ambiguous unless specifically defined, because it is used in three ways: (1) as a diverse group of fine-grained minerals, (2) as a rock term, and (3) as a particle-size term. Actually, most persons using the term clay realize that it has several meanings, and in most instances they define it. As a rock term, clay is difficult to define because of the wide variety of materials that compose it; therefore, the definition must be general. Clay is a natural earthy, fine-grained material composed largely of a group of crystalline minerals known as the clay minerals. These minerals are hydrous silicates composed mainly of silica, alumina, and water. Several of these minerals also contain appreciable quantities of iron, alkalies, and alkaline earths. Many definitions state that a clay is plastic when wet. Most clay materials do have this property, but some clays are not plastic; for example, halloysite and flint clay. As a particle-size term, clay is used for the category that includes the smallest particles. The maximum-size particles in the clay-size grade are defined differently on various grade scales. Soil investigators and mineralogists generally use 2 micrometers as the maximum size, whereas the widely used scale by Wentworth (1922) defines clay as material finer than approximately 4 micrometers. Some authorities find it convenient to use the term clay for any fine-grained, natural, earthy, argillaceous material (Grim, 1968). When used this way, the term includes clay, shale, or argillite, and some argillaceous soils. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, the term is generally understood by those who use it. Clay is an abundant natural raw material, and it has an amazing variety of uses and properties which will be discussed in this chapter. Clays rank among the leading industrial minerals in both tonnages produced and total value. Their importance is indicated in Table 1, which lists the 1978, 1979, and 1980 production and values according to the US Bureau of Mines (Ampian, 1980). Statistical data summarizing world production of kaolin, bentonite, and fuller's earth are compiled by the US Bureau of Mines (Ampian and Polk, 1981). The total world bentonite production in 1980 was 6,625,204 st of which the United States produced 4,184,619 st. The total fuller's earth produced in the world in 1980 was 1,952,600 st of which 1,534,000 st was produced in the United States. The total world kaolin production in 1980 was estimated at 22,971,000 st. Approximately 13 million tons of this total was produced in two countries, the United States and the United Kingdom. World production data on ball clay, fire clay, and miscellaneous clays are not available. As industrial minerals, clays are a complex group that consists of several mineral commodities, each having somewhat different mineralogy, geologic occurrence, technology, and uses. In this chapter these commodities are organized as follows: (1) bentonite and fuller's earth; (2) kaolin, ball clay, halloysite, and refractory clays; and (3) miscellaneous clay and shale. Bentonite and fuller's earth are grouped together because they are closely interrelated. Though bentonite is a term based on mineral composition and fuller's earth is a term based on use, the two are virtually inseparable, because much, but by no means all, clay sold as

Jan 1, 1983

By Walter Harvey Weed

CONTENTS. [ ] INTRODUCTION. THIS paper deals with certain ore-deposits whose structural features or mineral contents (or both) result, directly or indirectly, from igneous intrusions and their after-effects. It is largely a discussion of contact metamorphic ore-deposits based upon the physical changes in rocks due to contact action. It involves a classification of ore-deposits only so far as is abso-

Jan 1, 1913

By Dr. O’Neil Thomas J., Donald W. Gentry

There are mines that make us happy, There are mines that make us blue, There are mines that steal away the tear-drops As the sunbeams steal away the dew. There are mines that have lost the ore chute faulted, When the ore's forever lost to view, But the mines that fill my heart with sunshine, Are the mines that I sold to you. -Anonymous INTRODUCTION The preceding chapters have discussed, in various degrees of detail, the primary considerations necessary to perform a cash flow analysis of a mining-related investment opportunity. Although the previous discussions regarding the manipulations, calculations, and interrelationships of the various components of the pro forma income statement were illustrated in the text, many individuals are un- familiar with the format and appearance of a final spread sheet for the evaluation of a mining property. As a result, it seems appropriate to conclude this book with an abbreviated case study of an actual mine property (currently in production) showing the cash flow analysis and some back-up data. Obviously all of the supporting data and calculations for the case study presented cannot be provided; however, reference is made to the major assumptions utilized and to the appropriate procedures employed in the calculations, as described elsewhere in the text. The problem associated with using any case study for illustrative purposes is that one tends to be overwhelmed by detail. For instance, specific costs, prices, expenditure timings, and other variable values may be challenged because they either do not conform to one's expectations or are not consistent with specific operating experiences. When this occurs the instructional value of the problem becomes obscured. The purpose of most case studies, and particularly the one presented in this chapter, is to expose the student to the methodology, procedure, and format associated with performing a cash flow analysis of a mining property. It is not to laboriously wade through the specific details associated with operating and capital cost development, mine plans, or equipment schedules. It should be noted, how- ever, that the values represented in this case study result from specific mine plans, operating procedures, equipment spreads, manpower requirements, and other en-

Jan 1, 1984

By Herman Van Fleet, Frederick W. Neil, O&apos

The object of this paper is to describe the present status and possil~ilities of liquid oxygen as an explosive based upon the investigations, research and practical work of the Ingersoll-Rand Co., and of the Air Reduction Co., from early in 1922 to date. The following work was done. 1. A study of the history and physical theory of L. 0. X. as an explosive. (No attempt will be made in this paper to give the history or theory, as this has already been covered by the literature on the subject.) 2. An investigation of the use and the practice with L. 0. X. in the iron mines of Lorraine where L. 0. X. has its largest application in Europe. Although L. 0. X. is extensively employed in the iron mines of Lorraine, many of the mines using it exclusively, and blasting with it a total of approximately three million tons of iron ore per year, the fact that the mining practice in Lorraine1 is to drill comparatively shallow holes and blast only a few holes at a time, renders the data obtained there of very little value in estimating the possibility of replacing dynamite with L. 0. X. in American mining methods. In fact, in the iron mines in Lorraine, L. 0. X. replaced black powder, or its equivalent. 3. Laboratory research work on properties of absorbent materials. 4. Work in the Bureau of Mines explosive laboratory at Pittsburgh, Pa., on the properties of L. 0. 3. cartridges. 5. Practical work underground with L. 0. X. cartridges in the Kitherbee-Sherman iron mines at Mineville, N. Y. 6. Practical work in the quarries of the Calcite Quarry Co., Myers-town, Pa. 7. Practical blasting in several quarries and open-pit mines.

Jan 1, 1927

MINING ENGINEERING presents the annual membership report of the Society of Mining Engineers; see page 147.

Jan 7, 1964

By R. U. Fitting, A. C. Bulnes

Field experience with limestone and sandstone production indicates the existence of wide differences between the reservoir behavior of these two types of formation. Little attention appears to have been given to the separate study of the flow of fluids and the retention of fluids in limestones. This paper presents data and arguments to demonstrate the existence of a difference between the two types of formation, and urges the separate intensive investigation of limestone reservoirs. AH experimental data presented pertain to dolomitic limestone formations in west Texas and New Mexico. Two kinds of Porous media are recognized— intergranular and intermediate. Intergranular rocks are those in which the porosity and permeability are determined by the geometrical properties and the sorting of the sedimentary units; intermediate rocks, those in which there is no direct relationship between grain properties and the porosity and permeability. Limestones in general are intermediate media. The partial relationship between porosity and permeability of any class of Porous media is represelried by an area of .finite extent and definite shape on the permeability-porosity plane. The horizontal and vertical variations of porosity and of permeability in limestone and sandstone formations are discussed and compared. Comparisons are made of connate-water content, the relative permeability-saturation relationship, and capillary phenomena in the two kinds of rocks. A number of tentative conclusions are drawn relative to the reservoir properties of lime- stones; in particular, (I) dolomitic limestones are oil bearing and apparently are oil productive in zones of permeability less than 0.1 millidarcyj and (2) primary depletion (by gas expansion) oil saturations may be lower in dolomitic limestones than in sandstones. Introduction It is well known that the reservoir performance of limestones displays numerous irregularities when compared with that of sandstones, and that the departures from "normal" behavior of limestones are more frequent and generally more marked than in sandstones. This is particularly true of fractured limestones and those that have undergone considerable development of secondary porosity' A review of the literature of production research published during the past 15 years reveals a startling absence of theoretical and experimental investigations directed specifically toward explaining and predicting the performance of limestone reservoirs, even. though such problems as the prediction of water encroachment and the estimation of ultimate recoveries continue at the "inspired guess" stage. By far the greater part of the experimental data reported pertain to measurements on sandstone core samples, while the theoretical studies, almost without exception, are developed from the assumption of an ideal porous medium and therefore seldom are applicable to limestone formations. The chief cause of this situation appears to be the common belief that, to all practical intents and purposes, sandstones and the majority of producing limestone formations

Jan 1, 1945

By C. T. Eddy, R. W. Drier

The conductivity of copper wire is of prime importance to the electrical industry and consequently to the copper refiner and wire manufacturer. Annealed copper wire has a higher conductivity than hard-drawn wire, but, on the other hand, its tensile strength is lower. In an attempt to explain the reasons for these changes in properry. or at least to study the conditions existing in these two types of copper wire, the experiments described here were carried on in the Department of Metallurgy of the Michigan College of Mining and Technology This is only a partial and preliminary report on some of the work done to date on a research program of which the object is an intensive study of copper. It is offered with the hope that, though it is not an exposition of the most rigorous of conclusions, the general trend of inferences which may be drawn will be of value and interest. Effect of Direction of Drawing In 1928 some work was done on hard-drawn copper wires to determine whether wire drawn in a continuous machine (that is, all in one direction) would have a different structure from wire that had a reversal in direction at some stage of the drawing process. The diffraction spectra obtained indicated that as the position of the wire rayed approached the core, a preferential crystal orientation existed, and that the closer to the core the more preferred was the orientation. The data obtained partly corroborated the work done by Schmidt and Wassermanl and by Clark.2 Samples Used in Following Investigation The samples selected for use in both the diffraction work and the resistivity measurements were taken from Nos. 6, 8, 10 and 12 gage

Jan 1, 1930