Search Documents

By B. B. Zavoico

During 1936 the Russian oil industry made very satisfactory progress and, while not all difficulties of organization have been ironed out, the country is now assured of a supply of petroleum products in sufficient quantities and of quality demanded by modern motor equipment. The year 1937 promises to better by a wide margin the good showing of 1936. The statistics given in this paper for the first time take into consideration the varying gravities of crude oils of the several Russian oil fields instead of using a flat conversion factor of 7 bbl. per metric ton. It was found from the detailed study that the generally used average conversion factor should be increased from 7 to 7.25 bbl. per metric ton, the figure varying, of course, with the gravity of oil in the individual fields. Crude-oil production during 1936 is estimated at 201,500,000 bbl. as compared with 182,970,000 bbl. produced in 1935, an increase of 9.4 per cent. The greatest increase was again recorded in the Baku district, which increased its production by 10.9 per cent, from 141,257,000 bbl. in 1935 to 158,300,000 in 1936. Grozny district maintained its production at a level of about 23,000,000 bbl., but its old fields continued to decline and production was sustained by the development of newer fields. A great advance was made in drilling speeds and the total footage in 1936 reached 6,694,200 ft. as compared with 4,926,600 ft. drilled in 1935, an increase of 26.4 per cent. In older deep fields, producers were being completed at over 8000 ft.—a great depth for Russian drillers but two years ago. Several major discoveries were made in 1936. Northeast Caucasus.—Izberbash, east from Grozny and on the Caspian Sea, was the outstanding discovery, the initial production of the discovery well being around 3000 bbl. per day from about 5000 ft. The importance of the field is due to the large area of the structure, half of which, however, is under the sea, and also to its strategic location on the shores of the Caspian and near a trunk pipe line to the Grozny refining center. An active development program is being pursued in Izberbash and its 1937 production quota is set at 7,500,000 bbl. Achi-Su field, near Izberbash, also discovered during 1936, while not as prolific as Izberbash, is thought to cover a very large area and the small

Jan 1, 1937

By M. J. Sinnott

WITH the advent of nodular iron as an engineering material, considerable interest has been shown in developing this material for various applications. Generally the strength, hardness, or ductility are the more common properties used for design purposes but occasionally applications involving a knowledge of the thermal conductivity of the material is required. A search of the literature showed, rather surprisingly, that relatively little work has been done on this property for all types of cast iron. Insufficient data are available on thermal and electrical conductivities to develop the Weidemann-Franz ratio, or the Lorentz relationship, for estimation purposes. There are no data on nodular irons and the published data on malleable irons are quite sketchy. For these reasons the conductivity of the group of nodular irons listed in Table I were measured. Irons I to IV were made in such a fashion as to maintain the carbon and alloy content essentially the same while varying the silicon content. Test specimens were cut from the mid-section of 4-in. keel castings. Iron V is a commercial casting of nodular iron. The test specimen of this iron was cut from the center of a large cast billet 3x10x26 in. All alloys were tested in the as-cast condition. A microstructural examination showed that each iron had spheroidal graphite but the size and distribution varied with the silicon content of the iron. The spheroid size decreased while the number of graphite nodules increased as the silicon content of the iron was increased. The matrix structures of each iron consisted of pearlite and ferrite with the proportions varying from predominantly pearlite in the low-silicon iron to mostly ferrite in the high-silicon iron. The commercial heat, iron V, was predominantly pearlite probably because of its higher manganese and phosphorus content. Two methods for measuring the thermal conductivity were used. The first was a modification of the techniques described by Powell and Hickman and Van Dusen and Shelton,² the second method was a simpler technique described by Jakob and Hawkins." Since the agreement of both methods as tested on two sets of duplicate samples was excellent, the simpler experimental technique was used. The results of the measurements are given in Table II along with a summary of the microstructural constituents. These conductivity data indicate that as the percentage of silicon increases there is a corresponding decrease in the thermal conductivity even though the structure is changing from pearlitic to ferritic. Such a change in microstructure is usually accompanied by an increase in conductivity. A third factor involved in the behavior of these irons is the size and distribution of the graphite nodules. The relative amounts of graphite do not change greatly but the size and distribution do. Generally graphite improves the conductivity but in the present case such an effect is probably masked by the alloying effect from the silicon and its dispersion through the matrix. The thermal conductivity of the nodular irons studied is less than that of regular foundry irons by some 10 to 30 pct and is less than that of regular malleable irons.' The cause of the decreased conductivity is probably the more highly alloyed fer-rites obtained in these irons and the changed mode of distribution of the graphite as compared to the regular foundry irons. References R. W. Powell and M. J. Hickman: Journal Iron and Steel Inst. (1946) 154, No. 2, p. 99. 'M. S. Van Dusen and S. M. Shelton: U. S. Bur. Standards Journal of Research, RP668 (1934) 12, p. 429. ³M. Jakob and G. A. Hawkins: Elements of Heat Transfer and Insulation. 2nd Ed. (1950) New York. John Wiley and Sons. ' J. W. Donaldson: Journal Iron and Steel Inst. (1933) 128, No. 2, p. 255.

Jan 1, 1954

The industrial might of the Bowen Basin is primarily the result of Utah Development Co.'s work- which has opened up the Blackwater, Goonyella, Peak Downs, and Saraji mines; built the Hay Point port; and is now developing the Norwich Park mine.

Jan 1, 1977

By L. B. Herring, Harold Decker

The South Texas area, discussed herein, represents districts 2 and 4 of the Texas Railroad Cominission and extends from Jackson, Lavaca, and Gonzales Counties on the northeast to the Rio Grande River, comprising a total of 26 counties.$ The present boundaries of this district do not coincide with those of earlier reports published in the annual volumes of Petroleum Development and Technology. The war, in its various ramifications, determined and controlled all the phases of the oil and gas industry. Priorities for material and governmental subsidies determined all new operations. New Pools In our opinion, the combine' quantity of crude and distillate reserves added in '943 approached Or possibly exceeded the amount produced. Thirty-five new pools were added to the area' Of these, five have significant reserves and ten offer possibilities of containing consequential reserves. The largest proven reserve discovered during the year was the Slick pool, on the DeWitt-Goliad County line. This is also the most important Wilcox discovery to date in the area. The most significant extension was at Willimar, Willacy County. Other important extensions were developed at Agua Dulce, Seeligson, and Odem. Except for the Porter field, in Karnes County, the Laredo trend, which produces lrom the Jackson and Yegua, proved very disappointing, and this pool is o:C secondary importance. The Scott and Hopper pool, Brooks County, has only orie well, but offers excellent possibilities of becoming an important discovery. It represents at this time the major Frio discovery of the year. The Hobson pool, Karnes County, is not a major reserve, but can be classed as important in that it produces at a shallow depth from the Wilcox. This proves that the potential area of production for this zone occupies a broad trend. Gas and Condensate During the year construction was begun on only one recycling plant, this being in the Sejita field, Duval County. Several others were colltemplated, but no actual operations were begun. The most important development in recycling was the rebuilding of old plants to allow for the fractiona-tion of isopentane, n-butane, isobutane, and propane. Heretofore all pentanes plus have been marketed as cLdistillate,n only a minor portion of the butanes being isolated and sold for fuel purposes. All these new the except propane, are considered vital to the war effort and propane is being marketed as fuel gas. In other instances propane is being isolated and then pumped back into the gas reservoirs for storage. It is anticipated that the demands for this product will increase in the future. Drilling in the Wilcox trend during the year showed the existence of valuable gas

Jan 1, 1944

By L. B. Herring, Harold Decker

The South Texas area, discussed herein, represents districts 2 and 4 of the Texas Railroad Cominission and extends from Jackson, Lavaca, and Gonzales Counties on the northeast to the Rio Grande River, comprising a total of 26 counties.$ The present boundaries of this district do not coincide with those of earlier reports published in the annual volumes of Petroleum Development and Technology. The war, in its various ramifications, determined and controlled all the phases of the oil and gas industry. Priorities for material and governmental subsidies determined all new operations. New Pools In our opinion, the combine' quantity of crude and distillate reserves added in '943 approached Or possibly exceeded the amount produced. Thirty-five new pools were added to the area' Of these, five have significant reserves and ten offer possibilities of containing consequential reserves. The largest proven reserve discovered during the year was the Slick pool, on the DeWitt-Goliad County line. This is also the most important Wilcox discovery to date in the area. The most significant extension was at Willimar, Willacy County. Other important extensions were developed at Agua Dulce, Seeligson, and Odem. Except for the Porter field, in Karnes County, the Laredo trend, which produces lrom the Jackson and Yegua, proved very disappointing, and this pool is o:C secondary importance. The Scott and Hopper pool, Brooks County, has only orie well, but offers excellent possibilities of becoming an important discovery. It represents at this time the major Frio discovery of the year. The Hobson pool, Karnes County, is not a major reserve, but can be classed as important in that it produces at a shallow depth from the Wilcox. This proves that the potential area of production for this zone occupies a broad trend. Gas and Condensate During the year construction was begun on only one recycling plant, this being in the Sejita field, Duval County. Several others were colltemplated, but no actual operations were begun. The most important development in recycling was the rebuilding of old plants to allow for the fractiona-tion of isopentane, n-butane, isobutane, and propane. Heretofore all pentanes plus have been marketed as cLdistillate,n only a minor portion of the butanes being isolated and sold for fuel purposes. All these new the except propane, are considered vital to the war effort and propane is being marketed as fuel gas. In other instances propane is being isolated and then pumped back into the gas reservoirs for storage. It is anticipated that the demands for this product will increase in the future. Drilling in the Wilcox trend during the year showed the existence of valuable gas

Jan 1, 1944

By Samuel S. M. Chan

The magnetic susceptibilities of some ores and the major rock formations of the Precambrian Belt Supergroup in the Coeur d'Alene mining district were determined both in the laboratory by the use of the Gouy method and in the field with a Bison susceptibility unit. Trace element analysis of the same group of rock samples was also made using the atomic adsorption technique. Results of this preliminary study indicate that some correlation exists between the magnetic susceptibilities and the various rock formations. This may be useful for regional mapping and mineral exploration.

Jan 1, 1974

By AIME AIME

OUT of the fabulous iron ranges of Michigan?s Upper Peninsula since Pearl Harbor have come go to the steel mills to become tanks, guns, ships, and other weapons for a United Nations' victory. But the contributions to the war effort, as far as Michigan's iron country is concerned, do not stop there. The same men who mine iron ore deep inside the earth also are "mining" on top of the ground, gleaning a harvest of scrap iron and steel that is writing a big chapter in the War Production Board's salvage program. At virtually every mine over an area of a hundred square miles, everyone from the top mine official and straw boss to the man in the dippings is scrap conscious. They know the importance of the ore they mine but they are equally familiar with the importance of iron and steel scrap in war production. The successful job they are doing in salvage is a tribute to the entire Upper Michigan mining industry and to the man who marshaled them into action-John M. Bush, chief of the land department for the Cleveland- Cliffs Iron Co. at Negaunee, and for ten years an A.I.M.E. member. Also, this job should be an inspiration to 611 mining. metallurgical, and petroleum communities as to the latent possibilities of organized scrap recovery.

Jan 1, 1943

By R. J. Lloyd

INTRODUCTION The Mount Isa Mine is a large modern underground mine located in North-Western Queensland, Australia. Two ore types are mined and treated separately. Currently silver-lead-zinc ore is mined at the rate of 2.6 million tonnes per annum and copper ore at the rate of 4.6 million tonnes per annum. The silver-lead-zinc orebodies are mined by sub level open stoping and cut and fill methods whilst all copper ore is extracted by various forms of sub level open stoping. The mining operations are highly mechanised and utilise diesel powered load-haul-dump units of various sizes, two and three boom face drilling jumbos, electric-hydraulic rotary-percussive ring drills, in-the-hole hammer drills, rotary blasthole drills, raiseborers, battery/trolley locomotives, a large fleet of rubber tyred service and supply vehicles plus light rockdrills mounted on airlegs, rail mounted overshot shovels and battery and diesel powered locomotives. All stoping production ore is extracted with diesel powered load-haul-dump units. The ore is tipped into orepasses which connect to the main rail haulage levels. On the haulage levels electric battery/trolley locomotives are used to pull rakes of bottom dump or side dump trucks which feed the ore into primary crushers. Following two stage crushing the ore is conveyed to the shaft and hoistod to surface in bottom dump skips. Each ore stream has its own rail transport system, crushing stations and hoisting shaft feeding separate concentrators. This paper will consider some aspects of the role of equipment and machinery in the growth of the mine, will discuss in some detail the machinery and equipment in use today and will conclude with a look at some possible developments in mining equipment for the future, with particular reference to the Mount Isa Mine. A summary of mining equipment in use at Mount Isa is given in the Appendix. THE PAST Silver-lead-zinc ore was discovered at Mount Isa in 1923 and within a very short time many small mines were being developed. However the rich surface ore traces did not continue and by 1928 Mount Isa Mines Limited had acquired sufficient leases to plan for a large scale mine to exploit the low grade orebodies. At this early stage it was recognised that the mine would need to adopt the most mechanised mining techniques then available in order to overcome its twin disadvantages of low graaes and extreme remoteness. The Company introduced bar mounted drifters and overshot shovels to replace hammer and tap and hand shovelling in development work and by 1930 headings were advancing at the rate of 30 metres per week. In keeping with the concept of mechanisation the early engineers designed the Man and Supply shaft with a very large, for those days, cage compartment measuring 3.8 m x 3.4 m. This shaft was the main means of access into the mine for 36 years until the K57 shaft (now R62 shaft) was commissioned in 1966. Man and Supply is still in regular use. Production commenced in 1931 at an annual rate of approximately 660 000 tonnes of silver-lead-zinc ore. The mine was mechanised to an extent which was previously unknown in Australia; whilst the concentrator, smelter and power house utilised the most modern and efficient equipment available. Even so, the mine was very near to closure on several occasions and did not return a dividend to its shareholders for many years. Production levels remained at or slightly below 660 000 tonnes until a separate copper ore streani and mill was commissioned in 1953, doubling the existing production levels. The first underground crushers were installed at this time. Production rates expanded in the years between 1953 and 1973. By 1960 production reached 2740 000 tonnes of ore. In 1965-66 total production was 3650 000 tonnes and in 1973 the production rate plateaued at the current level.

Jan 1, 1981

By J. T. Lapsley, I. I. Cornet, A. E. Flanigan, R. Hultgren, J. E. Dorn

With the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that procedures of heat treating common magnesium casting alloys be investigated systematically. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. Research on the solution heat treatment and aging of magnesium alloy AZg2, (formerly ASTM No. 17; also known as Dowmetal C or AM26o) which was done under "Restricted" Project NRC-2I, in 1942-1943, and reported in detail in a final report to the OSRD on September 3, 1943, is the basis of this paper, which has been released for publication by the OSRD. American experience with magnesium alloys prior to World War II was limited, although some of these alloys had been in commercial use since 1909. Requirements of the aircraft industry for light alloys made it imperative to understand and utilize the advantageous strength-weight properties of magnesium castings. Magnesium casting alloys are commonly solution heat- treated to increase their ultimate tensile strength and ductility; this treatment may be followed by an age hardening at elevated temperatures, which raises the tensile yield strength but diminishes the ductility. In the present investigation, AZp was studied to determine the effects on properties of various solution heat treatment and aging schedules. The principles of heat treatment of magnesium alloys are the same as for other non-ferrous alloys. The alloy studied, AZp, has a nominal composition of 9 pct aluminum, 2 pct zinc, and minor constituents. Fig I shows, by the projection of isothermal sections on the concentration plane, the solubility surface1 of the ternary magnesium-rich solid solutions as determined by X ray 'analysis. From this figure it may be seen that above approximately 375°C (707OF), AZp alloy is a single phase alloy at equilibrium; below this temperature the equilibrium condition is a two phase alloy. The beta constituent which precipitates from the solid solution exerts a hardening effect. Because the zinc concentration is only 2 pct, ancl because of its solubility relations, AZqz resembles a binary alloy of magnesium with aluminum. The solubility curve1 of Fig 2 shows how rapidly the solubility of the beta phase decreases with decreasing temperatures. Unlike many aluminum alloys, magnesium alloys do not age harden at room temperatures; precipitation hardening of AZ² alloy is performed at about 177°C (350°F). At this temperature about 3 pct aluminum

Jan 1, 1949

By D. H. Newland

New York has a small but not insignificant place in the oil and natural gas industries of the United States. It has had a continuous record as an oil producer since 1872, with an aggregate yield of about 104,000,000 bbl. The reported output for 1935 was 4,237,000 bbl., a gain of more than 10 per cent for the year and a total that has been exceeded only in the early period of flush production half a century ago. The industry has been steadily building up since 1920 with the successful practice of the water drive, which has given a new lease of life to pools that had been practically drained of oil recoverable by pumping. An additional output of 2000 bbl. or more per acre is being procured by this method. Altogether the fields in New York State cover about 55,000 acres. Their limits are well defined and it is unlikely that they will be extended in the future, although there is some prospect of finding additional supplies by deeper drilling. The oil from New York is all classed as Pennsylvania grade, for which the recent price has been about $2.50 a barrel. It is refined at Olean, Wellsville and Bolivar, in the oil district, and partly in Pennsylvania refineries. Exploration for natural gas, outside of the established districts, was considerable during the year. Altogether 59 wells were drilled, distributed over 13 counties, of which 33 were listed as producers and 26 were dry. At the close of the year, 13 wells were in process of drilling. The 33 producing wells had a combined estimated flow of 278 million cubic feet per day. The best results were obtained from exploration in Allegany County, where out of eight wells drilled to the Oriskany sandstone five were successful and showed a combined open-flow capacity of 107 million cubic feet. The Oriskany sandstone was encountered at a depth of 4500 to 4900 ft. In Steuben County, next east of Allegany County, two out of seven wells to the Oriskany proved productive, and one of these, in the town of Greenwood, on the Watkins structure, was probably the largest that has so far been opened in the state, with a reported yield of 35 million a day. In the central part of New York interest was awakened by the activity shown in exploring for gas in the Trenton limestone, in Camden, Florence and Rome townships, Oneida

Jan 1, 1936

By D. H. Newland

New York has a small but not insignificant place in the oil and natural gas industries of the United States. It has had a continuous record as an oil producer since 1872, with an aggregate yield of about 104,000,000 bbl. The reported output for 1935 was 4,237,000 bbl., a gain of more than 10 per cent for the year and a total that has been exceeded only in the early period of flush production half a century ago. The industry has been steadily building up since 1920 with the successful practice of the water drive, which has given a new lease of life to pools that had been practically drained of oil recoverable by pumping. An additional output of 2000 bbl. or more per acre is being procured by this method. Altogether the fields in New York State cover about 55,000 acres. Their limits are well defined and it is unlikely that they will be extended in the future, although there is some prospect of finding additional supplies by deeper drilling. The oil from New York is all classed as Pennsylvania grade, for which the recent price has been about $2.50 a barrel. It is refined at Olean, Wellsville and Bolivar, in the oil district, and partly in Pennsylvania refineries. Exploration for natural gas, outside of the established districts, was considerable during the year. Altogether 59 wells were drilled, distributed over 13 counties, of which 33 were listed as producers and 26 were dry. At the close of the year, 13 wells were in process of drilling. The 33 producing wells had a combined estimated flow of 278 million cubic feet per day. The best results were obtained from exploration in Allegany County, where out of eight wells drilled to the Oriskany sandstone five were successful and showed a combined open-flow capacity of 107 million cubic feet. The Oriskany sandstone was encountered at a depth of 4500 to 4900 ft. In Steuben County, next east of Allegany County, two out of seven wells to the Oriskany proved productive, and one of these, in the town of Greenwood, on the Watkins structure, was probably the largest that has so far been opened in the state, with a reported yield of 35 million a day. In the central part of New York interest was awakened by the activity shown in exploring for gas in the Trenton limestone, in Camden, Florence and Rome townships, Oneida

Jan 1, 1936

By C. A. Stewart

I. INTRODUCTION AND GENERAL STATEMENT OF RESULTS. The field-work upon which this paper is based was done in the summer of 1910, and was made possible by the courtesy of the Imperial Copper Co., which gave me access to its property. For their kindness in this respect I wish to express my thanks to W. F. Staunton and Meade Goodloe. Moreover,. B. F. Smith and G. B. Gentry, mining engineers in the employ of the company, gave invaluable assistance by placing maps,. etc., at my disposal, and by discussing with me the problems of the district; and it is a great pleasure to acknowledge this indebtedness to them. In order that the significance of some of the details that follow may be better appreciated at first reading, a general outline of the conclusions reached is given here. In the Silverbell mining-district a series of Palaeozoic limestone blocks is completely surrounded by post-Palaeozoic igneous rocks, intruded in the following order: alaskite, alaskite-porphyry, biotite-granite, andesite, and quartz-porphyry. The biotite-granite is believed to represent a differentiation of the. magma from which the alaskite-porphyry came ; and this conclusion-has an important hearing on the origin of the ores. The intrusion of both alaskite-porphyry and biotite-granite was followed by the emission of magmatic waters, which sericitized and silicified the alaskite-porphyry and granite, and produced in the limestone, by the addition to it of silica, iron, and alumina, great masses of garnet, quartz, and wollastonite. Following close upon these solutions came metal-bearing magmatic waters, which impregnated porphyry, granite, and alas kite with cupriferous pyrite, and deposited in the garnet zones chalcopyrite and copper-bearing pyrite that make important bodies of contact-metamorphic ores. Secondary enrichment has taken place in the disseminated ores in the igneous rocks,. raising their copper-content to 2 per cent. in some cases,. and extensive drilling has been undertaken to block out these deposits. East of the contact-metamorphic deposits there is a fissure-vein of lead-silver ore in the quartz-porphyry. This rock is distinctly younger than the alaskite-porphyry and the granite; and the lead-silver ores belong, therefore, to a period of mineralization distinctly later than the copper-deposition.

May 1, 1912

By John J. Collins

[CONTENTS PAGE Purpose and scopeI Core samplingI Sludge sampling.....7 Combining core and sludge assays13 Deviation and surveying of drill holes17 Conclusions24 Acknowledgments25 Bibliography25] PURPOSE AND SCOPE The purpose of this paper is to review a few of the problems involved in the interpretation of diamond-drill core and sludge samples, with the hope that it will stimulate discussion and bring forth some of the information on the subject that has been accumulated by various organizations. The release of these data would benefit the mining industry as a whole. Particularly valuable would be the details of drilling programs that have been tested by actual mining operations, as most of the available published material is unsupported by production records. The scope of this paper is limited to a few of the commonest problems of interpreting diamond-drill core and sludge samples and the deviation of holes. It does not include the description of routine operations performed by the drillers, nor the estimation of ore reserves. The methods of calculating reserves have been described 25,26,31,32.50,65 but more information is needed on the results shown by actual mining operations. CORE SAMPLING The accuracy of diamond-drill-hole sampling depends in large measure on the percentage of core recovery. As a general rule, the longer the run, the poorer is the recovery. Although the longer runs allow cheaper drilling costs, the determining factor should be the percentage of recovery desired. The problem is one of balancing accuracy against costs. Holes of larger diameter may show improved recovery, except as Joralemon* points out that there are some conditions in which small holes give better core recovery than large holes. This is particularly true, he says, in rocks like shattered quartzite, where larger core tends to break in angular fragments and grind up, while the diameter of smaller core is less than the distance between joint planes and grinding is not so serious. In a large measure the length of the sample run should depend on the type of deposit. Favorable drilling may allow uniform sample runs of 5 ft., 10 ft., or perhaps 20 ft. In veins or beds of relatively narrow widths and changing characteristics, however, the ore zone may be overrun and ground in a core barrel full of waste rock. Generally it is desirable to break the sample at a change in the rock or ore. Such a change, often indicated by a color change in the sludge water, should be a signal for the driller to make a "dry" block and to pull out that run regardless of the length. Such a procedure permits the segregation of waste from ore samples so

Jan 1, 1946

By Bever M. B., Floe Carl F., Hung Liang

Data on the solubility of hydrogen in iron-silicon alloys are of practical interest, as hydrogen causes gas unsoundness and embrittlement in iron and steel and is also a factor in the metallurgy of cast iron. Zapffe and Simsl have recently demonstrated that in deoxidized iron and steel castings gassiness and bleeding are primarily functions of the hydrogen content of the liquid metal. These authors also suggested convincingly that ordinary melting and casting practice provides several sources of hydrogen for absorption by the metal. Norbury and Morgan2 and Boyles3 have shown that dissolved hydrogen affects the graphitization of cast iron. Schneble and Chipman4 included in a study of the effects of superheating on the properties of cast iron an investigation of the part played by hydrogen. Schwartz, Guiler and Barnett5 investigated the significance of hydrogen in the metallurgy of malleable cast iron. A complete interpretation of investigations of this kind calls for equilibrium values of the solubility of hydrogen in the liquid and solid phases. From the theoretical standpoint, the solubility of gases, especially hydrogen, may reveal some aspects of the nature of liquid metallic solutions. This was implied in the early work of Sieverts6 on the effect of alloying additions on the solubility of hydrogen in copper. Recent work by Bever and Floe7 has shown that in liquid copper-tin alloys the solubility of hydrogen changes abruptly at the composition of the intermetallic compound Cu3Sn. It is of considerable interest to determine whether liquid alloys of iron also have compositions at which the solubility of hydrogen exhibits a discontinuous or otherwise unique behavior. Among the various alloys of iron the iron-silicon system is important because of the presence of silicon in various structural alloy steels, transformer sheets, cast irons and special acid-resisting castings. The various grades of ferrosilicon, finally, cover almost the entire remainder of the composition range. Published information on the solubility of hydrogen in iron-silicon alloys is meager. The first values for pure liquid iron were reported in 1910-191 1 sieverts and Krumbhaar8 and by sieverts.9 They found that 100 grams of iron absorbs 28 c.c. of hydrogen at 1550°C and One atmosphere pressure, and 31 C.C. at 1650°C. In 1938 Sieverts, Zapf and Moritz10 published a value of 26.3 C.C. at 1550°C. Data on the solubility of hydrogen in liquid iron-silicon alloys and in liquid silicon are not available. Martin1' investigated

Jan 1, 1947

By Bever M. B., Floe Carl F., Hung Liang

Data on the solubility of hydrogen in iron-silicon alloys are of practical interest, as hydrogen causes gas unsoundness and embrittlement in iron and steel and is also a factor in the metallurgy of cast iron. Zapffe and Simsl have recently demonstrated that in deoxidized iron and steel castings gassiness and bleeding are primarily functions of the hydrogen content of the liquid metal. These authors also suggested convincingly that ordinary melting and casting practice provides several sources of hydrogen for absorption by the metal. Norbury and Morgan2 and Boyles3 have shown that dissolved hydrogen affects the graphitization of cast iron. Schneble and Chipman4 included in a study of the effects of superheating on the properties of cast iron an investigation of the part played by hydrogen. Schwartz, Guiler and Barnett5 investigated the significance of hydrogen in the metallurgy of malleable cast iron. A complete interpretation of investigations of this kind calls for equilibrium values of the solubility of hydrogen in the liquid and solid phases. From the theoretical standpoint, the solubility of gases, especially hydrogen, may reveal some aspects of the nature of liquid metallic solutions. This was implied in the early work of Sieverts6 on the effect of alloying additions on the solubility of hydrogen in copper. Recent work by Bever and Floe7 has shown that in liquid copper-tin alloys the solubility of hydrogen changes abruptly at the composition of the intermetallic compound Cu3Sn. It is of considerable interest to determine whether liquid alloys of iron also have compositions at which the solubility of hydrogen exhibits a discontinuous or otherwise unique behavior. Among the various alloys of iron the iron-silicon system is important because of the presence of silicon in various structural alloy steels, transformer sheets, cast irons and special acid-resisting castings. The various grades of ferrosilicon, finally, cover almost the entire remainder of the composition range. Published information on the solubility of hydrogen in iron-silicon alloys is meager. The first values for pure liquid iron were reported in 1910-191 1 sieverts and Krumbhaar8 and by sieverts.9 They found that 100 grams of iron absorbs 28 c.c. of hydrogen at 1550°C and One atmosphere pressure, and 31 C.C. at 1650°C. In 1938 Sieverts, Zapf and Moritz10 published a value of 26.3 C.C. at 1550°C. Data on the solubility of hydrogen in liquid iron-silicon alloys and in liquid silicon are not available. Martin1' investigated

Jan 1, 1947

By Carl F. Floe, Hung Liang, Michael B. Bever

DATA on the solubility of hydrogen in iron-silicon alloys are of practical interest, as hydrogen causes gas unsoundness and embrittlement in iron and steel and is also a factor in the metallurgy of cast iron. Zapffe and Sims1 have recently demonstrated that in deoxidized iron and steel castings gassiness and bleeding are primarily functions of the hydrogen content of the liquid metal. These authors also suggested convincingly that ordinary melting and casting practice provides several sources of hydrogen for absorption by the metal. Norbury and Morgan,2 and Boyles3 have shown that dissolved hydrogen affects the graphitization of cast iron. Schneble and Chipman4 included in a study of the effects of superheating on the properties of cast iron an investigation of the part played by hydrogen. Schwartz, Guiler and Barnett6 investigated the significance of hydrogen in the metallurgy of malleable cast iron. A complete interpretation of investigations of this kind calls for equilibrium values of the solubility of hydrogen in the liquid and solid phases. From the theoretical standpoint, the solubility of gases, especially hydrogen, may reveal some aspects of the nature of liquid metallic solutions. This was implied in the early work of Sieverts6 on the effect of alloying additions on the solubility of hydrogen in copper. Recent work by Bever and Floe7 has shown that in liquid copper-tin alloys the solubility of hydrogen changes abruptly at the composition of the intermetallic compound Cu3Sn. It is of considerable interest to determine whether liquid alloys of iron also have compositions at which the solubility of hydrogen exhibits a discontinuous or otherwise unique behavior. Among the various alloys of iron the iron-silicon system is important because of the presence of silicon in various structural alloy steels, transformer sheets, cast irons and special acid-resisting castings. The various grades of ferrosilicon, finally, cover almost the entire remainder of the composition range. Published information on the solubility of hydrogen in iron-silicon alloys is meager. The first values for pure liquid - iron were reported in 1910-1911 by Sieverts and Krumbhaar8 and by Sieverts.9 They found that 100 grams of iron absorbs 28 C.C. of hydrogen at 1550°C. and one atmosphere pressure, and 31 C.C. at 1650°C. In 1938 Sieverts, Zapf and Moritz10 published a value of 26.3 c.c. at 1550°C. Data on the solubility of hydrogen in liquid iron-silicon alloys and in liquid silicon

Jan 1, 1946

By J. W. Schroeder

SEAMLESS pipe, the product produced from piercing a solid round billet of steel by the Mannesmann process, was first produced in the latter half of the 19th century, the Mannesmann machine having been patented in 1885. The products of other processes also have been termed seamless pipe; for example, the cylindrical section produced by "cupping," which consists of forming a cup from a flat plate or disk and further elongating the cup into a tube by passing it through a set of reducing dies. The purpose of this paper is to discuss some of the more important metallurgical factors and their relationship to the economical production of seamless pipe produced by the Mannesmann piercing process. The first seamless tube plant in America was established at Shelby, Ohio, in 1891, and was employed in the manufacture of bicycle tubing. For a number of years the bicycle industry was the only user of seamless tubing, and this tubing was produced by hot-rolling pierced billets imported from Europe and finishing on the cold drawbench. At the turn of the century, the automotive industry was responsible for an increase in the demand for seamless tubing. The growth of this industry was the dominant factor leading to the phenomenal growth of the petroleum industry, which in turn created a tremendous demand for seamless pipe. In addition; the old lapweld iron boiler tubes for stationary and locomotive boilers were replaced gradually by seamless tubes. Since 1929, the production of seamless steel pipe and tubes has increased over loo pct. In 1929, 1,459,9031 net tons of seamless pipe was produced, including both hot-finished and cold-drawn material, as compared with 3,087,3122 net [ ] tons in 1948. Table I gives the distribution of seamless pipe by classes for 1948. METALLURGICAL PROBLEMS From a metallurgical standpoint, the production of seamless pipe has presented many problems. Practically every type of steel, carbon and alloy, with the exception of the superalloys developed during World War II, has been pierced and rolled successfully into tubing. This includes bessemer, open hearth, by the stationary and duplex processes, and electric steels. The range of sizes produced is no less staggering to the imagination, when it is considered that the hypodermic needle, which is 0.016 in. diam with a wall thickness of 0.004 in., and pipe for gas or oil transmission lines, with a 26 in. OD, are both seamless tubes. Between these extremes, the range of diameters and wall thicknesses meets most present-day demands for seam-

Jan 1, 1951

By V. H. Wilhelm

The outstanding event in the California petroleum industry during 1931 was the continuance of curtailment of crude oil production, which directly reduced drilling and well repair activities. Although all objectives were not attained, a very close balance between supply and demand was maintained during the period of maximum requirements, but the decline in intercoastal and export shipments caused an overproduction during the last half of the year, which indicated that California production would necessarily suffer further curtailment after the end of the year. A new peak in potential crude oil production of 1,187,600 bbl. per day was reported in August and at the close of the year the California potential was 1,069,000 bbl. per day, the shut-in light oil amounting to practically 425,000 bbl. per day and the shut-in heavy oil amounting to about 150,000 bbl. per day. Fig. 1 depicts these conditions and also shows the production and curtailment situation since the inception of proration in California. The December, 1931, potential figure of 1,069,-000 bbl. per day was arrived at after the most careful deliberation by a number of committees, selected to check the potential of practically every well in the state. Continued overproduction in the first three months of 1931 and the inadvisability of building more storage, together with the inability to obtain the proper amount of curtailment in town-lot fields, such as Long Beach, Santa Fe Springs and Playa del Rey, prompted the major oil companies to inaugurate a price reduction in crude oil. This cut caused prices to reach the lowest levels since 1915, and instigated the formation of an oil sales agency, composed of independent operators, which is known as the Oil Producers Sales Agency. The purpose of this organization is to procure a market for its members at reasonable prices, advise them of market conditions and aid them in controlling the amount of oil available for sale. Marketing of oil produced by members began on June 1 and independents controlling" about 160,000 bbl. per day of production had become members by the end of the month.

Jan 1, 1932

By R. W. Gurry

IN the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and 1110°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon content of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched. The mean result of concordant measurements is that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C. (1755°F.) and 1.89 per cent at 1110°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutectoid temperature (738°C. or 1360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature 1135°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. EXPERIMENTAL PROCEDURE The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.1 In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (16°F.) but at a given location the temperature remained within ±0.5°C. (0.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (1760°F.) and 1110°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with

Jan 1, 1942

By H. P. Moore, R. W. Fenn, Harold Margolin, W. R. Hibbard

DEFORMATION lines, also called etch markings or strain markings, are noneffaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries.1 Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrette to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation required for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted deformation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson' observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brick9 noted that deformation lines in 70-30 brass apparently associated with {111} planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards11 reported that in copper cold rolled less than about 50 pct few strain markings were apparent but for higher. reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass

Jan 1, 1948