Search Documents

By H. Lagendijk, I. J. Reinecke

Mintek was contracted by Oriel Resources plc in 2004 to conduct a preliminary assessment study on smelting ferronickel from the large but relatively low grade Shevchenko nickel ore deposit in Kazakhstan. A detailed feasibility study (?DFS?) was awarded to Bateman BV following promising results from the preliminary assessment study (?PAS?) and small-scale pilot plant test work. As part of the DFS, a total of 450metric tons of ore was collected from three different locations in the deposit and shipped to Mintek. After sampling, the bulk sample was prepared for smelting. This comprised crushing, screening and calcining with each step done separately for the three different lots. The chemical composition of the ore from the deposit is relatively high in silica and therefore falls out of the MgO to SiO2 range that is normally processed by pyrometallurgical means to produce ferronickel. The main objective of the testwork was to demonstrate that a method could be found and successfully applied to smelt these siliceous ores and produce an acceptable nickel-containing alloy. A 2-m ID DC arc furnace was installed with a twin-cathode (electrode) configuration to replicate the proposed commercial-scale furnace and also incorporated an advanced design of water-cooled copper panels in the lower furnace sidewalls to withstand the aggressive nature of the high SiO2-containing slags. The reductant used was a high-volatile coal from Karaganda in Kazakhstan. The reductant addition was adjusted to achieve a 90% recovery of nickel. In the assessment of the process metallurgy, some deviation from equilibrium conditions was observed. This deviation is ascribed to the intermittent existence of a smelting bath partially covered with feed during the testwork. Optimization of smelting conditions should result in the metallurgy (slag metal equilibrium) being closer to the theoretical predictions and make the production of a 20% nickel alloy possible at 90% nickel recovery. The solution for the successful processing of these siliceous ores was found in the attainment of the necessary operational stability through the control of arc length, operating temperature, open-bath smelting conditions and flux additions of up to 10% dolime for the most siliceous of the three ore types. The test work carried out by Mintek provided the basis for the process flow sheet and engineering design of the DC arc smelting furnaces for the Shevchenko Nickel project.

Jan 1, 2007

By Faruk Oksuz, Clay Haynes, Miguel Sanchez, Patrick Finn, Roger J. Maurer

The Milwaukee Metropolitan Sewerage District’s (MMSD)’s challenges of basement flooding and wet weather sewer overflows are being creatively addressed with the Northwest Side Relief Sewer tunnel. The $132 million, 20-foot diameter, and37,740 feet long conveyance and storage tunnel excavation in dolomite at depths reaching 165 feet below ground surface has been successfully completed within13 months in April 2004. This paper includes Owner’s perspective on the overall project, and the design and construction details by the Designer and the Contractor. The project contract documents included a comprehensive Geotechnical Data Report and the Geotechnical Baseline Report.

Jan 1, 2005

By James D. Noll, Eileen Birch

In a previous study, the e?cacy of commercial and prototype impactors for sampling diesel particulate matter (DPM) in coal mines was investigated. Laboratory and ?eld samples were collected on quartz-?ber ?lters and analyzed for organic and elemental carbon. Coal dust contributed a minimal amount of elemental carbon when commercial cascade impactors and prototype impactors, designed by the University of Minnesota (UMN) and the US Bureau of Mines (BOM), were used to collect submicrometer dust fractions. Other impactors were not as e?ective at excluding coal dust. The impactors evaluated in that study were either not commercially available or were multi-stage, expensive, and di?cult to use for personal measurements. A commercial version of the BOM impactor, called the DPM Cassette, was recently introduced by SKCs. Tests were conducted to evaluate the performance of the DPM Cassette for measuring diesel-source elemental carbon in the presence of coal dust. Bituminous coals from three mines in two di?erent coal provinces were examined. The dust particle diameters were small and the coal dust contained a high percentage of carbon, there by giving a worst-case condition for non-anthracite coal mines. Results for the DPM Cassette were essentially identical to those obtained by the BOM impactors in a previous study. At a respirable coal dust concentration of 5.46mg m3, which is 3.8 times the regulatory limit, the DPM Cassette collected only 34µg m3 of coal-source elemental carbon.

By A Goldstone, T Maton

The Golden Cross Mine is located on the North Island of New Zealand, at the base of the Coromandel Peninsula, approximately 8 km northwest of Waihi. The project is operated as a Joint Venture with Coeur Gold New Zealand holding 800/0 and Viking Mining Limited with a 20% interest. The past open-pit and underground gold and silver producer has been in the reclamation phase of the operation for approximately 2.5 years and is now nearing completion. Although rehabilitation of the site is a regulatory requirement, the Closure Plan has been enhanced by the ongoing commitment of the Joint Venture to establish a sustainable land use for the site by commissioning engineered facilities designed to last for perpetuity. The Joint Venture identified six significant design features that were key to successful rehabilitation. These were the controlled placement of acid generating waste rock into engineered disposal sites; the design and placement of sealing layers over the waste rock disposal sites; the design and construction of diversion drains; the establishment and management of vegetation to protect the oxygen diffusion layer; a partial capping of the tailings to accelerate consolidation adjacent to the tailings dam embankment, and the implementation of a cyanide recovery circuit to recycle cyanide from the tailings prior to disposal. Another key to success for the project involved genuine consultation with all parties participating in the planning, evaluation, and consenting of the closure process at Golden Cross. The local and regulatory community has been widely represented in the Joint Venture's operating and closure plans throughout the history of the mine. Participants include: Regional and District Councillors and staff members, professional peer reviewers, environmental groups, local residents of the valley, and Iwi. This overall commitment to the project has resulted in a world-class rehabilitation program for the first modern metal-mine closure in New Zealand and we believe that collectively, the work done at Golden Cross is helping to set a standard for the success of future programs within the extractive industry.

Jan 1, 2000

By J. T. Jordaan

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree This paper addresses the critical parameters that need to be considered when designing a mechanized bord-and-pillar mining layout for a narrow tabular steep dipping orebody. These parameters are : ?Reef dip ?Reef width ?Geological structures within the orebody ?Physical dimensions of the selection of machines ?Gradeability of the selection of machines. The main objective in designing such a layout is to maximize machine efficiencies whilst minimizing dilution. This methodology was then applied in the design of a mechanized bord-and-pillar mining layout for a given piece of ground (Vlakpoort and Moddergat) using a given selection of machines. This piece of ground contains the PGM bearing UG2 Reef with an average thickness of 124 cm and dipping at 18°withadverse strike and dip changes. Two bord-and-pillar layouts were designed for this area. Layout 1 is characterized by the use of strike conveyors to convey ore on strike with an average LHD hauling distance of 35 m. Layout2 uses LHDs for all on strike conveyance of ore with an average hauling distance of 75 m. These two layouts were then technically and financially compared. It was concluded that layout 1 is theoretically superior but layout 2 was chosen due to its greater flexibility and probability of operational success. Layout 2 was also compared to conventional mining and it was concluded to be more economically feasible. However the latter is a proven mining method in these conditions and has a lower risk operational failure. Bord-and-pillar mining has some favourable promises such as improving labour difficulties, lowering operating costs and providing safer working conditions. The success of mechanized bord-and-pillar mining in narrow tabular steep dipping orebodies will depend on the extent of the research and development efforts which need to create and innovate technologies to overcome some of the current limitations stated in the above-mentioned parameters.

Jan 1, 2003

By E. Chin

The domination of Bangladesh's mineral industry by natural gas was in for some possibly significant changes. A modest flow of crude oil was struck in a gas development well in the northeastern corner of the country. This was the first commercial flow of crude oil in Bangladesh. All crude oil was being imported, which cost a significant proportion of the nation's foreign exchange earnings. The development of an oilfield producing only a few thousand barrels per day would be a welcome help to the economy. Additional exploration at a 1985 coal discovery in the northwest indicated a considerable reserve of good-quality coal at a depth suitable for mining. If the coal is mined, it would be a boon to the local economy because natural gas was not available in the area.

Jan 1, 1988

A comprehensive analysis of rock structures in non-oriented (axially oriented) drillcore is now available (Laing, in press). The system embodies new concepts which better equip the geologist and engineer to deal from the outset with optimising the acquisition of structural information in drillcore, logging: interpreting, and graphically presenting the results. The few existing techniques for determining orientations of structures are augmented by a wide range of new techniques, and all are brought together into two solution types by considering the underlying Euclidean geometries. Analysis of these solution types in terms of what data are required to implement each solution and what assumptions need to be made, leads to strategies which facilitate intelligent design of different drilling programs for blind and outcropping situations. Drillcore is variably structurally fertile, depending on the number of different structures present. This concept fosters the selective logging only of the more fertile core. Drillholes are also variably fertile, depending on their orientational relationship to the structures in the host rocks. Structural parameters are either vectorial or non-vectorial. Vectorial structures parameters comprise normal structural orientations plus polar vectors like vergence, younging, shear sense and so on. They can be determined by one of two solution types: external solutions, which use an external reference structure to fix the drillcore and thus permit orientation of all structures within that core, and internal solutions, which use orientational data from a selected structure at three or more different drillhole orientation to determine the unique orientation of that structure, without reference to any external structure. Both solution types rely on constant orientations (orientational stability) of the selected structure, but the internal solution actually provides its own test of orientational stability. External solutions are the norm in outcropping situations and internal solutions are invaluable in blind situations. In blind situations sequential "internal then external" solutions can be used respectively to provide a reference structure and then use this for subsequent external solutions at individual points downhole. Blind prospects can now be drilled and interpreted as easily as outcropping prospects. Each solution type has its own optimum requirements. External solutions are ambiguous for certain orientational relationships between the drillhole and the reference structure (for example, a perpendicular relationship), hence drillholes in which external solutions are planned should be designed to avoid these orientations. Internal solutions are ambiguous for straight drill paths, and are most unambiguously resolved when the drill path attains maximum drillhole dimensionality, that is, it occupies a wide variety of orientations in 3D space; hence drillholes in which internal solutions are planned should be designed as combinations of non-parallel holes or as individual strongly curved holes. For both solution types an understanding of the kind of structural fertility required leads to intelligent design of drill paths, which is termed structural drill targeting. It is distinct from spatial drill targeting, which is the process which defines and (x,y,z) point-or volume-target. Effective design of drilling programs requires both structural and spatial targeting. The external and internal solutions for vectorial parameters are implemented via (1) visual (qualitative), (2) stereographic, or (3) core orienting frame procedures. Each of these has its own advantages. Stereographic procedures have been simplified via the erection of a drillcore reference frame in which three fundamental angles are defined, and the formulation of an all-inclusive set of stereographic recipes for determining orientations from the measurement of these angles. Non- vectorial structural parameters comprise an ad hoc array of useful measures which are simply described by numbers. Examples are angles between structures, and density of structures. Such parameters (some of which provide useful vectors toward ore bodies) are invaluable in drillcore because they can be measured and recorded rapidly, without determining the orientation of the core. In a summary, non-oriented drillcore can now be structurally mapped exactly as if it were outcrop. Interpretation of the significant volume of unique structural information which is beginning to flow from this system can be optimised by using, in addition to the conventional cross section and longditudinal section, three new modes of presentation. The natural cross section is that section in space normal to a principal structure of interest. It is a section in which it is advisable to drill to obtain certain structural information, and in which the results need to be presented. A newly defined unique cross sectional orientational symbol is recommended for dramatic improvement in the quality of information presented in cross sections. Stacked level maps are a powerful adjunct to cross sections.

Jan 1, 1990

By Felipe Perissé Duarte Lopes

The tensile properties of DGEBA/TETA epoxy matrix composites reinforced with different amounts of curaua fibers were evaluated. Tensile specimens with up to 35% in volume of long, continuous and aligned curaua fibers were room temperature tested in an Instron machine. The fracture was analyzed by SEM. The results showed significant changes in the mechanical properties with the amount of curaua fibers. This was compared to other bend-tested composites with distinct matrices. The fracture analysis revealed a weak fiber/matrix interface, which could be responsible for the comparatively low performance of some properties.

Jan 1, 2010

By Robert Anderson

Advance knowledge of roof conditions can lead to improvement in roof control strategies that will reduce roof falls and ultimately will reduce injuries to mine workers. J.H. Fletcher and Company, in cooperation with West Virginia University, has been developing a system to meet these needs by collecting torque, thrust, and rotation speed data during drilling operations. Recent improvements in analysis algorithms to detect anomalies in the roof structure as well as various display enhancements for real time mapping and evaluation of roof structures have been incorporated into current Fletcher Information Display system. The unit has also been housed in an explosion-proof container to allow use in coal mine applications. Recently, the system has undergone extensive field trials in several limestone mines and one coal mine. During these trials, the National Institute for Occupational Safety and Health assisted Fletcher in verifying the accuracy of the roof mapping capability of the system by comparing the display information to bore hole scoping observations and drill corings. It was concluded from this assessment that the intelligent drilling system can complement scoping and core analysis to provide a more complete picture of roof strata and is capable of seeing features or conditions that are not always obvious in these more traditional methods.

Jan 1, 2007

By W E. Vance, B H. Ashton

The emission of seam gases into underground workings in coal mines is acknowledged as a major hazard, particularly methane due to its possible ignition. Acknowledge of seam gas parameters is important for the prediction of gas emission rates into the ventilating air current. They are also important as the basis for the evaluation of the likely contained gas as a possible energy source.   Gas content determinations for the Kupakupa seam have been made at the Huntly West Mine.  Applying the method of Creedy (1986) to face samples, gas contents of 1.80 and 1.66 have been determined. Using desorbed and residual gas content data a content of 1.92 m3/t has been derived. These are on an ash included basis. Calculations using the adsorption equation of Kim (1977) and coal quality have given a gas content of 2.19 m3 t. Long-hole exploration drilling at Huntly West Mine has provided information on gas pressure. A pressure rise test has given a reading of 500 kPa (absolute); this is low compared with the pressure given for the determined gas content from theoretical adsorption isotherms.

Jan 1, 1991

By Claus Goetzel

THE object of this investigation was to determine whether silver alloys could be used instead of the currently employed insert of high-expansion AVERAGE COEFFICIENT PER DE G. C. OVEN RANGE 20° To 200° C. Pure aluminum '31.6 X 10-6 Cast low-expansion Si-Cu-Ni-Al piston alloy 20.0 X 10-6 High-expansion austenitic Cu-Ni cast iron 19.3 X 10-6 Cast steel (0.25-0.35 C, 0.10-1.0 Mn) 12.6 X 10-6 Cast iron (3.15 total C, 2.16 Si) 12.8 X 10-6 Pure silver 18.9 X 10-6 austenitic ferronickel alloy, to reduce the wear of ring grooves in light metal pistons. A typical example of a piston containing a ferronickel insert is shown in Fig. 1. The high coefficient of expansion of silver made it worthy of consideration, while the small size of the insert would render it use feasible in Germany as an emergency in is- tire. The coefficients of linear expansion of several metals and alloys are as shown in the table above. Obviously the melting point of the insert must be high enough to prevent it from melting when the light alloy is cast around it. This imposes a lower limit of about 850° C. for the solidus of the silver alloy. Pure silver melts at about 961° C., so that the Fin. 1.-PISTON CONTAINING tolerable depression in the solidus is rather FERRONICKEL INSERT. small. To avoid deformation of the insert during use a Brinell hardness number of at least 60 appears necessary.

Jan 1, 1937

By P Allen, E Gleeson, D Boakye, R Chesher, S Konopa

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Not only do epithermal gold deposits provide many challenges in estimating mineral resources, the complexities of these deposits also provide technical challenges in assessing appropriate mining and processing strategies, as well as social and environmental planning and management. The characteristics of epithermal gold deposits include being highly variable with respect to geometry and gold grade distribution, the presence of other economic contributors, mineralogy, texture, rock strength, weathering and alteration overprint. These characteristics influence the economic value of mining projects in an interlinked manner. Consequently, successful exploitation of epithermal deposits requires a holistic approach, coupled with the effective integration of geological data to meet all aspects of mine development decision-making. This paper presents examples of the key technical challenges encountered in estimating and mining epithermal deposits. It also highlights why these issues need to be addressed from the viewpoint of geology, sampling, resource estimation, mine planning, mineral processing and social and environmental planning for the true value of the mining project to be realised.CITATION:Konopa, S, Chesher, R, Gleeson, E, Allen, P and Boakye, D, 2015. Challenges in maximising the value from epithermal gold deposits, in Proceedings PACRIM 2015 Congress, pp 127–132 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By K. Saito, Y. Miyauchi, T. Nishi, Y. Kizu

At Tokushima Plant of Nippon Denko Co., Ltd. high-carbon ferromanganese is produced by the electric furnace method using lump manganese ores and sintered manganese ores manufactured from fine manganese ores. However, the distribution of manganese ores is significantly uneven on earth, and their characteristics considerably vary by ore type. It is known from experience that the production of high-carbon ferromanganese by the electric furnace method depends greatly on material ores. Therefore, to maintain stable operation in the electric furnace-smelting field, it is important to identify the characteristics of each type of material ores in advance. Thus, we evaluated the high-temperature electric characteristics of manganese ores using the electrical conductivity measuring system developed by ourselves and provided the standards for determining ores and blending ratio necessary for stable operation of the electric furnace based on the evaluation results. This time we worked for optimisation of the high-temperature electric characteristics of sintered manganese ores through modification of the characteristics because the blending ratio of sintered manganese ores in the electric furnace is high. The electrical conductivity of sintered ores having various chemical components in a high-temperature region (up to 1 550°C) was measured using our electrical conductivity measuring system and high-temperature electric characteristics evaluating method reported at INFACON 9. As the result of the measurement, we revealed that the high-temperature electric characteristics of the sintered ores depend on their chemical contents and the sintered ores can be modified to those having excellent high-temperature electric characteristics by controlling their chemical contents, so that the resources can be effectively used.

Jan 1, 2004

By William H. Schiffbauer

One of the safety and health research programs of the former U.S. Bureau of Mines Pittsburgh Research Center was the evaluation of technology that will provide remote-controlled operation of mechanized equipment in underground room-and-pillar mining. The purpose of this effort was to enable workers to be located away from the hazardous and unhealthful coal extraction area (the face). As part of this program, advanced machine navigation and control technologies were developed for underground room-and-pillar and highwall coal mining that can be applied to commercially available mining equipment. These technologies use off-the-shelf components and a flexible control software architecture to minimize the effort required to adapt them to mining equipment. An accurate, reliable navigation system that can provide the mining machine's heading and location is a critical requirement for a remote-controlled mining system. After investigating several different types of navigation sensors, researchers selected the Honeywell Ring Laser Gyro Inertial Navigation System (INS) as showing the most promise. It was installed on a continuous mining machine at our Mining Equipment Test Facility. Extensive testing at an open pit (OP) site was also performed. This report describes the INS as it was employed on the mining machine in the laboratory, in the field, and OP tests, and provides the accuracy and performance results of the OP and highwalltests.

Jan 11, 1997

By Enrique Touceda

FOR a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At -the outbreak of the war the firm decided to specialize in the manufacture f propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods f manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual -blade mold formed, the pattern is then rotated on the spindle to the position- for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this practice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface f each blade must be chipped too the templet and through this procedure chipped to such accuracy, as will be required for a static balance. Inasmuch as the' work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin f the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days f foundry work and about the same length of, time for the machining. Through the use f the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity, with any particular propeller-wheel design,

Jan 4, 1921

Twenty field-scale tests were conducted in a 28 MW pulverized coal power plant in Healy, Alaska, to examine mill power consumption in relation to coal grind size. The intent in this field-scale study was to verify if grind size truly impacted power consumption by a detectable amount. The regression model developed from the data indicates that grind size does impact mill power consumption, with finer grinds consuming significantly more power than coarser grinds. However, other factors such as coal hardness (i.e., the lower the Hardgrove Grindability Index, or the harder the coal, the higher the power consumption) and mill throughput (i.e., the higher the throughput, the higher the power consumption) had to be included before the impact of grind size could be isolated. It was also observed that combining amperage and flow rate into a single parameter, i.e., specific amperage, hurt modeling. Cost analysis based on the regression model indicate a power savings of $19,972 per year if the coal were ground to 50% passing 76 mm rather than the industry standard of 70% passing 76 mm. The study also demonstrated that size reduction constituted a significant portion of the power consumption.

Jan 1, 2008

By Corate L. Brierley

Low-grade porphyry copper ores containing chalcopyrite as the primary mineral was leached by two strains of acidophilic, thermophilic microbes belonging to the genus Sulfolobus. Leach tests were conducted in glass columns heated to 60-70° C. Pinto Valley and San Manuel ores sized to -1/2 inch + 50 mesh were effectively leached by the thermophilic organisms, but pinto Valley and Cyprus Bagdad ores sized to -2 inch + 1/2 inch resisted leaching. Aeration did not contribute measurably to bacterial copper extraction, since two columns, one inoculated and one sterilized, having a rest/ leach cycle without recurrent aeration exhibited copper extraction patterns similar to those of the aerated columns. Distilled water can be substituted for 9K medium without diminishing copper extraction. Decreasing the pH of the leachate to about 1.8 enhanced the extraction of copper from pinto Valley ore with the thermophilic microbes. Thiobacillus ferrooxidans was found to be relatively ineffective at copper extraction from pinto Valley ore. Of eleven solvent extraction reagents tested, Adogen 364 and Warsol at concentrations of 0.1% and 0.012 were inhibitory to oxygen uptake by the two Sulfolobus strains. Di-2-ethyhexyl phosphoric acid at concentrations of 0.1%, 0.01% and 0.001% were totally inhibitory to the respiration of both organisms.

Jan 1, 1979

By Edward Thomas

Yucca Mountain Overview The U.S. Department of Energy?s Yucca Mountain Project is a geologic repository project designed to receive, handle, package, transport, and emplace spent nuclear fuel and high level radioactive waste. The planned repository would be located in Yucca Mountain on the western edge of the Nevada Test Site, about 90 miles northwest of Las Vegas, Nevada, and would include both surface and subsurface areas. Yucca Mountain rock formations consist of successive layers of volcanic rocks (called tuffs) approximately 14 to 11.5 million years old, formed by eruptions of volcanic calderas to the north. With the volcanic rock the potential for methane emission is not an issue and the subsurface repository is a non-gassy (methane) classification. This paper will provide a summary of the development ventilation system design that provides fresh air for subsurface construction activities, and the emplacement ventilation system design that removes heat generated by the waste packages. The subsurface layout, illustrated in Figure 1, contains 108 emplacement drifts, one Performance Confirmation(PC) observation drift, nine intake/exhaust shafts, and three access ramps. The existing Yucca Mountain facilities, shown in bold lines in Figure 1, include a 7.8 km long, 7.62 m (25 ft) diameter U shaped tunnel that is formed by the North and South Ramps at both ends of the Exploratory Studies Facility (ESF) drift and a 1.5 km long, 5.0 m (16.4 ft) diameter Enhanced Characterization of the Repository Block drift (ECRB) that were constructed from 1994 through 1998. These drifts were used for site characterization activities and have been incorporated into the subsurface repository configuration. The unexcavated perimeter access main and exhaust main drifts are typically 7.62 m (25 ft) diameter TBM excavations and the emplacement drifts are 5.5 m (18 ft) diameter TBM excavations. The turnouts leading into the emplacement drifts are to be excavated by either mechanical, or drill and blast methods and serve as the launch chambers for the emplacement drift TBM excavations.

By D Pastars, J L. Mauk

Located at the southern end of the Awhitu Peninsula, the Waikato North Head ironsand mine is approximately 50 km southwest of Auckland . The ironsand deposit consists of Quaternary sands, clays and peats, formed by aeolian and marine processes. We sampled on widely- and closely-spaced intervals to test variability within the mining area. X-Ray powder diffraction shows that samples contain feldspars, quartz, pyroxenes, amphiboles, clays and titanomagnetite. Densities range from 1.6 to 2.5 grams/cubic centimetre, with porosities from 30 to 43 percent. The percentage of magnetic minerals values range from 0 to 75 percent, slimes (clay minerals) values of 0 to 26 percent and non-magnetic minerals from 20 to 95 percent. Mineralogical differences in the Mitiwai Formation and Waiuku Blacksand Member cause bimodal populations in the density, magnetic minerals, nonmagnetic minerals and slimes plots. The Mitiwai Formation has higher non-magnetic mineral values and lower density, slimes and magnetic mineral values than the Waiuku Blacksand Member.

Jan 1, 2001

By Jeffrey K. Whyatt

The Crandall Canyon accident investigation included an interesting and unexplained observation by rescuers that the ?barrier rib had shifted northward as a unit, as much as 10 feet.? This is not the first mention of such a movement, although such reports are rare. Historical accounts describe unusual movement and displacement of intact coal, cribs and timbers. Two movements of particular interest are the creation of gaps above coal pillars and falling of standing support elements without apparent damage. A dynamic boundary element program was used to explore movements induced by slip on geologic features removed from the affected panel. While the resulting models are much too simple to fully replicate these observations, they do show that the types of phenomena observed are possible. They can also provide insight into the types of motions that ground support elements are subjected to during large bump events. This was demonstrated for the case of a large bump in a Book Cliffs coal mine. Seismic information suggested the source mechanism to be normal slip on a fault. A model of that source showed initial dilation of the panel followed by dynamic compression and rebound ? consistent with underground observations. The initial dilation is important as it may allow slender standing support to shift or fall.

Jan 1, 2009