Search Documents

By Burton Scott

A device for detecting carbon monoxide at ppm levels is described which is based on the measurement of infrared absorption at 4.65 microns. The unique feature of the nondispersive infrared instrument is contained in the optical design which includes a confocal cavity, increasing the effective optical path length by a large factor, thus greatly reducing the required package size. The cavity has the effect of reducing the total amount of radiation passing to the detector, but at the same time increasing the percent attenuation observed when adding CO, by a factor called gain. The radiation is chopped by a filter wheel which contains narrow band filters at 4.0 and 4.65 microns. The resultant signal produced by the pyroelectric detector is demodulated by the electronics to product an automatic gain control signal, proportional to the total radiation, and a difference signal, proportional to the CO present. Tests of a breadboard model are described which show cavity gains of 10 with noise levels equivalent to 2 to 10 ppm CO.

Jan 1, 1975

By Arthur L. Holloway, James C. Mugford

"The Underground Research Laboratory (URL) is located in southeastern Manitoba, in the Lac du Bonnet granite batholith of the Canadian Shield. It was constructed by Atomic Energy of Canada Limited (AECL) to conduct geotechnical research for the Canadian Nuclear Fuel Waste Management Program, assessing the concept of permanent disposal of nuclear fuel waste deep in plutonic rock.One of the primary objectives of the research program at the URL is to develop a nondestructive rock mass characterization method that can be used during siting, design and construction of a used fu el waste disposal vault. An experimental program was established to assess radar reflection profiling as a technique for fracture characterization in granite. The highly resistive, homogeneous nature of the Lac du Bonnet granite is ideal for the propagation of electromagnetic energy at the radar range of frequencies and water-filled fracture zones act as excellent reflectors because of their contrasting electrical properties.Radar reflection profiling was undertaken to characterize a major fracture zone located between 5 m and 10 m below Room 211 on the 240 m level of the URL. The profiling was done at a frequency of 120 MHz, on a 1m grid laid out on the bare rock floor of the room. Reflectors identified in the analog data were correlated between the profile lines, digitized, and a three-dimensional surf ace for each recognizable reflector was constructed. These surf aces were then compared with data obtained from the examination of numerous cores from adjacent boreholes intersecting the fracture zone. A very good correlation was found between the major radar reflectors and the most intensely fractured regions of the zone. Modelling studies also showed that a series of prominent shallow radar reflectors were caused by a borehole drilled close to Room 211."

Jan 1, 1990

The U.S. Bureau of Mines conducted a series of laboratory tests in a full-scale model to determine the respirable quartz dust capture efficiency of an irrigated-filter collection system while testing different filter densities, different filter materials, preconditioning water sprays, and wetting additives in the spray water. Impactor samplers were operated upstream and downstream of the filter unit to determine overall dust collection efficiency. The impactor filters containing the 0.7-to 4.7-J.l-m size fractions were analyzed for quartz content, and these data were used to calculate quartz dust collection efficiency. The results of this testing indicated that (1) increased ftIter density improved quartz dust collection, but also resulted in a significant increase in pressure drop across the filter, (2) an alternate synthetic filter material improved dust collection without increasing pressure drop, (3) preconditioning sprays mounted in the system ductwork can have a beneficial effect on dust collection, and (4) additives to the spray water did not significantly increase dust collection.

Jan 1, 1990

By James Su

The Green River Valley in Kent, Washington, is a fast growing area containing retail facilities, warehouse factories and industrial businesses, including the Boeing Space Center. Traffic from Interstate - 5 to the West Valley Highway is highly congested. Accordingly, a new corridor, including a bridge across the Green River, was designed and constructed between 1996 and 1997. This paper presents a case history of the design elements and issues associated with the construction of the pier foundations of the bridge. Subsurface conditions were evaluated using both deep test borings and CPT soundings to evaluate the strength and consolidation properties of the supporting soils. Subsurface conditions consisted of alternating layers of loose and medium dense silty sand and sandy silt. Engineering analysis included an assessment of liquefaction as well as pier supporting capacity and associated settlement. The constructed foundations included 6-foot-diameter piers cased to a depth of 120 feet below the ground surface. The pier casings were driven to the design tip elevation and the soil inside the casing was removed by drilling. Despite performing borings and CPT soundings at specific pier locations, occasional trees, buried thousands of years ago through geologic processes, were surprisingly encountered during pier construction. This presented unique and difficult driving and drilling conditions. During drilling, the water level inside the piers was maintained near the ground surface to create a balance of hydrostatic pressure and prevent boiling of soils the bottom of the casing. After the casings were installed, the soil inside the casing was excavated, the rebar cage was installed and the pier was filled with concrete using treme techniques. Construction of the piers is complete and the completed piers have experienced negligible settlement. Owner: City of Kent Engineering Department Timothy La Porte, Project Manager Kent, Washington General Contractor: Mowat Construction Company, Kirkland, Washington Foundation Contractor: Condon - Johnson & Associates, Inc., Tukwila, Washington

Jan 1, 1998

By T. O. Llewellyn

The Bureau of Mines conducted batch-?scale tests on a sample of parphyry copper mill tailings as part of a study to determine the feasibility of rutile recovery from this source. The tailings that were tested contained 0.75 percent titanium dioxide (Ti02), with about two-thirds of the Ti02 values occurring as rutile. Mineralogical studies indicated that about one-half of the Ti02 content could be considered recoverable. Beneficiation studies of the tailings showed that best flotation results were obtained when sulfides and carbonates were removed by bulk flotation prior to rutile flotation. Rutile flotation was most effective when a petroleum sulfonate collector was used in an acid circuit. From this basic method of flotation, two alternative procedures were developed. The first procedure was to size and grind the tailings to minus 200 mesh; deslime the total pulp; and then float the sulfides, carbonates, and rutile. The second procedure was the same, except that it did not include sizing and grinding. Flotation of the sized and ground tailings yielded rutile concentrates containing 43.1 percent Ti02 and 75.7 percent of the recoverable Ti02. Rutile concentrates floated from the tailings that were deslimed but not ground contained only 34.7 percent Ti02 and 69.4 percent of the recoverable Ti02.

Jan 1, 1980

By Franklin D. Cooper

This Bureau of Mines report reviews in detail the foundry coke situation in the United States in 1975. It discusses intrinsic production problems and identifies opportunities for modifying operating practices so that the quality and yield of foundry coke can be enhanced without unnecessary investment in new equipment. Major topics include operating data and attendant practices and problems, the relationship of carbonization phenomena to coke quality and yield, environ- mental impacts of foundry coke plant operations, suggested research and development opportunities, and data on components of oven charges and on foundry coke production and shipments.

Jan 1, 1977

By Victor R. Spironello

The Bureau of Mines has conducted studies of the slags related to ferrous technology to evaluate experimentally acceptable substitutes for the auxiliary flux, mineral fluorspar, in steelmaking operations. Comparative heats were made in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF) to evaluate a waste material known as "used potlining." Used pot lining is recovered from alumina reduction cells after its useful life and contains significant levels of fluorine and sodium in various compounds. This material in both lump and pelletized form provided adequately fluid slags, based on observations made during BOF operation. No adverse effects were found on furnace performance, metal and slag chemsitry, the strength of the steel produced, or the environment. Fluorine recovery in the slag was about the same as that obtained when using fluorspar, as were the losses to the scrubber water and solids. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag. The sodium recovered in the slag apparently also contributed to fluidity, since the fluorine input was at about two-thirds that of the fluorspar. Used potlining was determined experimentally to be a satisfactory substitute for fluorspar in basic oxygen steelmaking.

Jan 1, 1982

By F Pirajno

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. China’s mineral deposits are the result of metallogenic processes associated with the geodynamic evolution of tectonic plates and eventual amalgamation into their modern configuration. The principal tectonic provinces of China comprise the North China Craton, Yangtze Craton, Cathaysia Craton, Tarim block, Altay-Tianshan-Hinggan orogens (part of the Central Asian Orogenic Bel), Central China orogens, Songpan-Ganze orogen and Alpine-Himalayan fold belts, which are part of the huge Tethysides. These tectonic elements are testimony to a complex geological history spanning more than 3000 million years. This contribution will focus on selected areas of the Altay-Tianshan, the fold belts surrounding the North China Craton and Yangtze Craton and the mineral systems along the Ailaoshan-Red River fault zone. Mineral deposits in these provinces include gold, copper, molybdenum, tin, antimony, nickel, platinum group elements, lead and zinc.CITATION:Pirajno, F, 2015. Metallogeny and related tectonic settings in China , in Proceedings PACRIM 2015 Congress, pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Michael A. Staiano

The objective of this study was to determine the magnitude and sources of environmental noise from mining operations near populated areas, to de-scribe monitoring techniques, and to identify applicable existing noise abatement techniques. To this end, noise surveys of a representative sample of mines and quarries were conducted. Noise levels at site boundaries and near specific equipment and ensembles of equipment were measured. Noise exposures in terms of annual day-night sound level were calculated for the boundary noise measurement locations. In addition, the relative sound level contributions were estimated for the mining equipment noise sources affecting the boundary locations. Noise abatement methods falling into three categories were analyzed: equipment practices, operational/administrative practices, and equipment quieting. Selected applications of noise abatement methods were evaluated in hypothetical situations with emphasis upon machinery selection and use. Procedures for measuring noise around mining operations were provided.

Jan 1, 1981

By Roger L. Baer

Marine disposal of mill tailings has been practiced worldwide for over a century. However, only recently have the environmental effects of marine disposal been systematically studied. Some early attempts at marine disposal of tailings resulted in adverse impacts to marine life. However, recent advances in tailings disposal methods have included the introduction of engineered submarine tailings discharge systems, advanced environmental assessment and monitoring methods, and oceanographic modeling systems. Successful submarine tailings disposal (STD) has occurred at several mines. The U.S. Bureau of Mines (BOM) has undertaken studies of the disposal of mining and milling wastes in the marine environment. The BOM Alaska Field Operations Center, Juneau, initiated a review of the technology, regulations, and economic aspects of STD. The review illuminated the need for organization of literature on the subject, therefore the Bureau compiled this extensive bibliography on marine disposal of mill tailings. The bibliography presented here contains 1483 references and is also available through diskette in the Word Perfects format. A review of the references indicates that literature on submarine disposal inadequately covers the subject. The majority of the references listed only peripherally relate to the subject. Published literature on the engineering and environmental aspects of STD is severely limited.

Jan 1, 2011

By R. L. Mazza

This final report on methods of reducing and controlling methane in coal mine gob areas indicates that vertical degas holes are beneficial to the mines of northern West Virginia working the Pittsburgh Coal. The USBM funded project involved the drilling and testing of eight vertical holes (four over longwall panels and four over room and pillar panels) based on a review of 13 previously in existence. Areas of observation included gas production history, flow entry profile, underground methane reductions, strata separations, and casing loads (accompanying subsidence). Observations led to the drilling of successful holes drilled short of the mine. Eleven gas production response to applied vacuum tests were conducted at nine degas holes under the contract. Significant production responses were recorded over longwall gobs.

Jan 1, 1977

By J. L. Holman

The Bureau of Mines has extended its previous development of cast Mn-Cu damping alloys to powder metallurgy (P/M) consolidation of alloys containing 55 to 75 wt-pct Mn. Blends of minus 200-mesh elemental powders were compacted cold in directional and isostatic presses. With 1 pct binder, typical green densities ranged between 76 and 80 pct of theoretical when pressing at 30 or 48 tsi. Green strength increased with compacting pressure and copper content. As-sintered tensile strengths ranged to 60,000 psi fox a hydrogen, sintered 60Mn-40Cu alloy, along with 5-pct elongation. Sintered densities ranged between 90 and 96 pct of theoretical. Sintering (a as effective when holding for 1 hr at maximum temperatures of 900° to 1,040` C, dependent on composition. Strength and ductility were considerably lower than for equiva¬lent cast alloys. When aged to the damping condition, alloys containing 60 to 70 pct Mn exhibited >40 pct specific damping capacity (SDC) at 5,000-psi stress, considerably higher than values reported for equivalent cast material. Effects of 1 or 3 pct Sn or Zn additions on SDC and other properties were assessed. Trials were conducted on consolidating rings and gears of the 65Mn-35Cu alloy on industrial-type P/M equipment.

Jan 1, 1979

One of the problems associated with the maintenance of roadways in underground coal mines is that of dealing with roadway closure. Sidewall weakening technique is based on the transference of the high stress zone further away from the vicinity of roadway. This transferral is carried out by weakening parts of sidewalls of roadway by cut- ting slot, drilling a series of parallel holes or blasting during development stage. In the paper, the effect of sidewall weakening on the stability of roadway is studied by finite element analysis and field experiment. The finite element analysis shows that sidewall weakening can control the development of yield zone around a roadway, improving the stability of roadway. It is also shown that if in- situ horizontal stress is lower or higher than the in-situ vertical stress, it is difficult to obtain roadway stability by sidewall weakening. The field experiment shows that roadway closure can be controlled by sidewall weakening with blasting.

Jan 1, 1990

By Terry S. Cory

This report describes the results of a measurement program to determine the broad spectral characteristics of both differential and common mode noise on phone lines in three coal mines; and, signal attenuation spectral characteristics on the same broad basis over phone line strings with taps/branches. The frequency range used was baseband -1000 Hz for resolution bandwidth ranging from 100 Hz near baseband to 30 KHz near I MHz. The signal attenuation measurements were performed on all three "legs" of taps where possible and applicable. Results were obtained comparing shielded and unshielded phone lines In one mine. The results include an improved electromagnetic noise chart for coal mines showing variations with types of mines, topology, and location of noise sources; also, fundamental high-frequency limit on untreated phone lines in coal mines is identified

Jan 1, 1981

By M. Troyer

A coal shuttle car equipped with a pulsed laser optical ranging system to provide guidance for an automatic steering system was tested in production coal mining. Test results are presented for the two mines where testing took place, and some operator's reactions are included. Automatic steering control keeps the car cantered in an entry, and automatic turns are made at intersections as signaled by the operator. All other controls-tram, conveyor, brake, etc, remain manual and require operator control. Complete override of steering while in the automatic mode is retained by the operator, who may grab the steering wheel at any time and turn in opposition to the automatic signal by applying about 10 foot-pounds of torque.

Jan 1, 1976

By Dale R. Ralston

This investigation was divided into two major phases. Phase I of the study was an examination of the occurrence and production of acid water within the Bunker Hill Mine in northern Idaho. The second phase of the project involved the study of water movement through an abandoned tailings pile. Mineralogy and hydrogeology were determined to be the two most important factors in the acid mine drainage problem. Low pH water was formed in the mine in areas of lead-zinc ore rich in pyrite. Water movement in the mine was important in the production of acid and the transportation of heavy metals. Areas of recharge to the mine were identified. A data collection network was installed to monitor water quality and quantity changes. The quantity of acid drainage from the mine was found to vary directly with surface runoff events. The study of the abandoned tailings pile was performed to determine the characteristics of water movement through the tailings material and the resultant impact on the hydrologic environment. The Page Tailings Pile, abandoned in 1969, was utilized as a study area. An extensive network of piezometers and meteorological data collection sites were installed in and near the pile. Data collected to date indicate the presence of a ground-water mound under the east half of the pile. Some transfer of ions from the tailings pile to the ground-water system has been detected.

Jan 1, 1973

By Robert A. Bradburn

The Bureau of Mines has developed a miniature, portable two-level oxygen-deficiency alarm and produced three prototype models. Each operates from a 4.2-v dc power source, and the highest current drain of any model is 80 ma. An electrochemical cell, which produces an electrical output in proportion to the partial pressure of oxygen to which it is exposed, is used as an oxygen detector. The output of the cell is applied to an electronic circuit that detects two different levels of oxygen percentage below that of normal air, and produces distinct audible signals at these levels. The hazard alarm mode is activated when the oxygen percentage first drops below normal and produces a 500-cps "beep" tone with an intermittency of 1 cps. The danger mode produces a continuous 500-cps audible signal when the oxygen percentage drops still lower.

Jan 1, 1968

By M. J. Beus

Many mines in Canada, the United States and South Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due to the excessive weight. It has been suggested (DeLorme, 2000) that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm (13/4 in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg (10 ton) skip could exceed the safety factor of the rope. To improve on the current understanding of the mechanical behaviour of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modelling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca, 1999), is used to simulate the structural behaviour of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modelling on the wire rope will be discussed.

Jan 1, 2002

By Rajni Patel, John McDonald, Steve Dubnewych, Michael McKenna

The Upper Reach segment of the Northeast Interceptor Sewer (NEIS) is a3.2-km-long tunnel excavated in interbedded marine sedimentary deposits with approximately 40 m of cover. The tunnel was initially classified by Cal/OSHA as “potentially gassy.” During excavation, high levels of hydrogen sulfide and methane were encountered, prompting Cal/OSHA to reclassify the tunnel as “gassy.” In addition, the tunnel excavation encountered an abandoned, 100-year-old water tunnel known as the “Narrows Gallery.” This existing tunnel was completely full of water and under 30 m of hydrostatic head. This paper will discuss the unanticipated difficulties and design solutions implemented to construct a gassy tunnel exposed to high volumes of water.

Jan 1, 2005

By J. J. Shields

This study by the Federal Bureau of Mines concerns different methods of face haulage used with various types of continuous-mining machines, mobile-loading machines, and track-mounted equipment under varying roof and bottom conditions and in coalbeds of varying thicknesses. This report is the ninth in a series on mechanical mining in bituminous coal mines. Reference to the reports previously published is made in appendix III, p. 106. Use of modern mining equipment in bituminous coal mines has resulted in increased productivity at the face. This especially is true where continuous-mining machines are used, and the supervision is good. Previous methods and equipment for moving coal from the face became inadequate and had to be improved to restore balance to the mining systems. Sometimes new equipment was needed to improve the face haulage, and in some instances, a new combination of existing equipment was used. Detailed studies of face haulage methods were made at 13 mines in Pennsylvania, West Virginia, Ohio, and Illinois to compare their effectiveness and to describe fully the conditions under which each method was used.

Jan 1, 1960