Search Documents

By Paul J. Sabatini, Yazen A. Khasawneh

"A Demag CC1800 crawler crane was partially erected on crane mats adjacent to a seawall when settlements near a corner of the crane mat area were observed to be slightly larger than previously assessed. A ground improvement program including installation of dry soil cement mix (DSM) piers was implemented to improve soil bearing capacity. Due to near-surface obstructions, only 75 percent of the DSM piers were installed to the design depth. Because of the partial installation of the DSM piers, an evaluation of the crane pad stability and the effect of the crane loading on the stability of an adjacent 10-ft high concrete seawall, which was believed to have limited (if any) reserve capacity, was required. A two-dimensional finite element model was developed to evaluate the responses of the partially improved ground and the sea wall to the loads imposed by the crane. Geotechnical site investigation and laboratory testing programs were performed to better define the subsurface conditions near the area where settlements occurred and to provide the required mechanical parameters for the soil constitutive model. Analysis results indicate that total and differential settlements of the crane pad and the increase in load on the seawall were tolerable provided limited excavation and replacement of weak dredged soils outside the DSM area would be implemented.INTRODUCTION & BACKGROUNDA Demag CC1800 was erected on 8 ft × 16 ft crane lattice mats at about 12 ft from an existing seawall. Approximately 3.5 in. of subsidence was observed at one corner of the crane mats, while the crane was partially erected and stationary. The approximate location of the crane mats with respect to the existing seawall when the subsidence occurred is shown on Fig. 1.The seawall consists of a reinforced concrete wall connected by reinforced concrete bents to a composite section of sheet pile wall; the total depth of the seawall is about 29 ft. The bents are spaced at about 20’4” and supported by five piles at each bent location. The composite sheet pile consists of concrete and a sheet pile section with a reinforced concrete wale section. The retaining wall is about 10 ft in height and is supported at three levels. The first support level comprises a 2-½” diameter steel rod near the top of the wall spaced at 40’8” the second and third level supports comprise 1-½” diameter steel rods spaced at about 5’6”. The second level support is inclined at about 10 degrees below horizontal and the third level support is oriented horizontally through the wall footing. A schematic of the seawall section is shown on Fig. 2.A geotechnical site investigation was implemented soon after the subsidence was observed. The program included advancing four borings to a depth ranging from 16 ft below ground surface (bgs) to about 30 ft bgs. In general, the investigation showed sandy material (likely fill that was used behind the retaining wall) from the ground surface in two borings located immediately behind the retaining wall. The other two borings furthest from the retaining wall showed very soft to soft clay (possibly dredged material) from the ground surface to a depth of about 10 ft bgs. Based on this information, the ultimate bearing capacity of the subsoils was estimated to range from 1,200 to 2,000 pounds per square feet (psf). From the anticipated crane loading (weight of the crane and loading lifts), a minimum allowable bearing capacity of about 1,500 psf would be required for safe operation. To achieve the required bearing capacity a ground improvement program was selected and implemented."

Jan 1, 2017

By Robert B. Fulton

The use of industrial minerals by the chemical industry as raw materials for manufacturing and in processing spans a wide assortment of minerals. This chapter aims to supplement rather than duplicate the commodity chapters. Its objective, to describe the uses of industrial minerals in the manufacture of chemicals, is attained by considering minerals used by the chemical industry in terms of the chemical element required and by giving particular emphasis to market factors. The mineral aspect, which is covered in the commodity chapters, is subordinated and attention is focused on the chemical and market aspects. Condensing this broad subject into a few pages permits treating only the most important elements derived from industrial minerals. The elements derived from petroleum, hydrogen and carbon, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potash, and nitrogen for fertilizers and titanium dioxide for pigments. After eliminating on this basis, our definition leaves six elements of major importance: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. Salt brines have particular importance as raw material sources for the chemical industry as shown in Table 1 "Salt Brine Derivatives" (Anon., 1967), which charts the chemical compounds derived from four types of brines: (1) Owens Lake type brines which are sources of boron and sodium compounds; (2) Midland type brines from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake type yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak type produced mainly for lithium. Table 2 (Jones, 1973) affords an overview of the chief industrial minerals, the chemical products derived from them, and end uses of the products.

Jan 1, 1975

By J. D. Ramsdell

To obtain information on the effects of cobalt on microstructure and tensile properties of titanium-vanadium-cobalt alloys, the composition ranges of 4 to 16 percent vanadium with 1 to 4 percent cobalt have been studied. The beta phase was not completely retained with vanadium additions up to 16 weight-percent or in the same alloys containing up to 4 percent cobalt.

Jan 1, 1960

By H. A. Domian, H. Biloni, G. F. Bolling

Jan 1, 1965

By Svend [Bue] Rondum

The final report contains a summary of the work performed under this contract, In addition to the report itself, other products were derived from this effort. Several hardware items were prototyped for use with underground belt conveyors, and a manual for installation and maintenance procedures was developed and published under separate cover. Recommendations have been included for implementation of the tools and the manual or, an industry-wide basis.

Jan 1, 1982

By A. Andrews

Paper written on project work carried out in partial fulfilment of MSc (Eng) degree Solid state sintered silicon carbide ceramics are used in aggressive environments as sealings. There exist data concerning corrosion, but there are only few data concerning their electrocorrosion behaviour. Therefore the electrochemical corrosion of solid state sintered silicon carbide (SSiC) ceramics has been studied at room temperature in acidic and alkaline environments by using potentiodynamic polarization measurements. The investigation showed a pronounced electrochemical corrosion in bases and acids. In HCl andHNO3pseudo-passivity features due to the formation of a thin layer of SiO2on the surface were observed, whereas in NaOH soluble silicate ions were observed, resulting in more pronounced corrosion. The microstructural observations of initial and corroded samples reveal that the residual carbon found in the microstructure do not dissolve preferentially. Keywords: Corrosion; SEM; SSiC; polarization test.

Jan 1, 2006

By R. Hansson

Zincite and spinel phases are present in the complex slag systems encountered in zinc/lead sintering and zinc smelting processes. These phases form extensive solid solutions and are stable over a wide range of compositions, temperatures and oxygen partial pressures. Accurate information on the stability of these phases is required in order to develop thermodynamic models of these slag systems. Phase equilibria in the Fe-Zn-O system have been experimentally studied for a range of conditions, between 900 and 1580°C and oxygen partial pressures (pO2) between air and metallic iron saturation, using equilibration and quenching techniques. The compositions of the phases were measured using Electron Probe X-ray Microanalysis (EPMA). The ferrous and ferric bulk iron concentrations were determined using a specially developed wet-chemical analysis procedure based on the use of ammonium metavanadate. XRD was used to confirm phase identification. A procedure was developed to overcome the problems associated with evaporation of zinc at lowpO2s and to ensure the achievement of equilibria. An isothermal section of the system FeO-Fe2O3-ZnO at high ZnO concentrations at 1200°C was constructed. The maximum solubilities of iron and zinc in zincite and spinel phases in equilibrium were determined at pO2=1*10-6atm at 1200and 1300°C. The morphology of the zincite crystals sharply changes in air between 1200 and 1300°C from rounded to plate-like. This is shown to be associated with significant increase in total iron concentration, the additional iron being principally in the form of ferric iron. Calculations performed by Fact Sage with a thermodynamically optimized database have been compared with the experimental results. Keywords: Phase Equilibria, Fe-Zn-O, Quenching, Wet-Chemistry, EPMA, XRD, ISP.

Jan 1, 2004

Process Options for Difficult Arid-Region Nickel Laterites In the absence of the discovery of significant nickel sulfide deposits, the future of Australia's nickel industry will increasingly depend on cost effect processes for low-grade nickel laterites. The problems encountered with the West Australian HPAL plants, resulting in three of the four plants being shut down, have caused the industry to revisit atmospheric leaching options, particularly heap leaching. West Australian laterites are characteristically very varied in grade, chemical composition and mineralogy with the result that, thus far, one process does not fit all laterites. In this paper the leaching of an especially refractory ore is compared using column leaching of whole ore and atmospheric leaching and HPAL processing of ground ore. The key characteristic is the resistance of the goethite phase to acid attack with low-to-moderate temperature leaching conditions. The refractory characteristic is attributed to the stabilising influence of chromium and aluminium and possibly manganese substitution in the goethite crystal structure and goethite morphology. A significant three-fold increase in both nickel and cobalt extractions under atmospheric leaching conditions was achieved by the relatively simple modification of bubbling sulfur dioxide into the reaction vessel to create a reducing environment. Recoveries increased from <30 per cent to 90 per cent nickel and 86 per cent cobalt after 10 hours of leaching at 95¦C. An even greater improvement was achieved under ambient conditions by heating the ore to temperatures above 250¦C for 30 minutes. Subsequent leaching at ambient temperature gave an eight-fold increase in both nickel and cobalt recoveries after 14 days bottle rolling. Both methods could be optimised and implemented in such a way as to increase laterite reserves in conjunction with a heap leach operation but may be better suited to vat or closed tank processing.

Sep 13, 2010

By A. S. Macfarlane

This paper describes how knowledge of the orebody morphology and ore morphology can be used to optimize the planning, mining, and metallurgical output from an open pit copper mining operation, such as to significantly increase the stability of the whole value chain process, and increase the reliability and value of the process outputs. In the case under consideration, the orebody contains both copper and cobalt. This in itself provides a challenge, in that the two metals do not occur in consistent ratios across the orebody as a whole. Furthermore, mineralogical differences within the orebody have a significant impact on plant performance in terms of throughput rates, acid consumption, and recoveries. In order to stabilize and optimize the plant performance, it is necessary to firstly have a complete understanding of the geometallurgical factors that affect performance, and then to have a sound knowledge of how these are distributed within the orebody. These models then inform the mine planning strategy that optimizes cash flow and NPV, and also allow the development of a stockpiling strategy that not only stabilizes the plant, but also allows variations in the plant feed according to ore type and grade in volatile price scenarios. Integral to the realization of these opportunities is the establishment of an appropriate measuring, control, and reconciliation system, customized to the optimization objectives. The paper describes how all of these factors and strategies can be integrated to produce optimal value from the orebody through to final dispatched product. It also shows the significant value that can be released through such an approach.

Jan 1, 2014

By Paul-Dominique Oudenne

For many years, CMI NESA has gained considerable experience in the field of alternative thermal processing processes by which useful by products result in addition to the destruction of the raw wastes. The CMI NESA pyrolysis process has been extensively applied to a wide range of sewage, industrial sludge and residues. This paper describes in details the development works carried out at the pilot stage as well as the key parameters of the process. Some of the industrial realisations are briefly described, the most recent one being the erection of a sludge pyrolyser on predried sludge at 90% dryness of a capacity of 100 tons of dry matter per day for the Valenton plant of the SIAAP (city of Paris).

Jan 1, 2006

By F. M. L. Mulaudzi

Metal dusting is a corrosion phenomenon that occurs in strongly carburizing gas atmospheres at elevated temperatures. Reaction kinetics and product characterizations of Alloys 602CA and 800 were examined by scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX) and X-ray diffraction (XRD).The results showed that Alloy 602CA is more resistant to metal dusting than Alloy 800. Visual examination and SEM surface analysis showed that Alloy 800 suffered metal dusting attack after a relatively short exposure period. The amount of coke deposits increased on Alloy 800 with increased exposure from 96 to 336 hours. X-ray diffraction on the reacted surfaces identified graphite and austenite in both alloys and some iron oxides/spinel for Alloy 800.

Jan 1, 2012

By Philip Bonanno

The first major project in Boston's new access to Logan Airport was an Immersed Tube Tunnel which extended 3,600 ft. from South Boston to East Boston across Boston Harbor. Twelve tube sections, 300 ft. long x 80 ft. wide x 40 ft. high, were lowered into an excavated trench which was then backfilled. The depth of the trench at mid-channel was approximately 100 ft. below mean high tide. At the East Boston end the tube terminated close to the present shoreline. At the South Boston end the tube terminated approximately 600 ft. inland from the shore line where a ventilation building was required. The depth to subgrade from existing ground at the ventilation structure was approximately 85 ft. The soil profile at this location consisted of 50 ft. of miscellaneous rubble fill, 25 ft. of Boston blue clay, and 10 ft. of glacial till. A small amount of weathered argellite existed at the north end of the structure. Part of the Morrison Knudsen, Interbeton, J.F. White, Joint Venture contract to construct the Immersed Tube Tunnel (ITT) was the construction of a cofferdam at the tube/ventilation building interface. The ventilation building was to be built as part of another contract. The construction of the cofferdam and the excavation to the building subgrade was the responsibility of J.F. White Contracting Company.

Jan 1, 1994

By Jewel A. G. Gomes

Green rust (GR) are layered Fe(II)-Fe(III) double hydroxides, having a pyroaurite-type structure consisting of positively charged hydroxide layers and hydrated ions in interlayers. This special feature of GR is very efficient for wastewater treatment as the pollutants are easily taken in or exchanged with the anions in the interlayers. It can be simply and cost-effectively produced by electrocoagulation (EC). Chicken processing plant (CPP) produces large amount of wastewater containing variety of readily biodegradable organic compounds, fats, and proteins. The possible re-use of properly treated CPP wastewater would be economic and environment friendly. In this study, we present our work on treatment of CPP wastewater using EC, specifically for the removal of COD. Analysis of the EC-treated water for reuse in the same plant is discussed considering the U.S.EPA regulations. Two types of EC-reactors were used for this purpose. To better understand the treatment mechanism, EC-floc was also characterized using XRD and SEM-EDS.

Jan 1, 2010

By S J. Loach

Geological reconciliation is an indispensable part of BHP Billiton’s Western Australian Iron Ore (WAIO) operations. Since 2009 our reconciliations have been calculated in a single, centralised sequel-server database. This system draws data from across our operations and calculates a hierarchical sequence of reconciliation factors that span the company from the smallest grade control (GC) block to the whole of WAIO. It then presents the results using sophisticated graphical reporting tools.The initial motive for developing WAIO’s reconciliation system was to meet corporate compliance and public reporting requirements. The ability to validate our resource and reserve models by comparing their estimates of tonnes and grade with production figures remains the system’s principal function; however, as the system has matured, we have significantly developed its ability to support the improvement of various technical activities within the business. For example, the system can now calculate and report reconciliation factors for different resource classifications, short-term planning models and geometallurgical estimates.More recently, great emphasis has fallen on the system’s ability to detect and warn of possible geological issues that may pose a risk to either production schedules or product quality. We envisage a future where automated analysis of our large historical data set will enable high-risk conditions within future mine plans to be detected and highlighted.In all of these ways geological reconciliation plays an important role in contributing to this company’s financial and operational resilience.CITATION:Loach, S J, 2017. The development and future of BHP Billiton’s Western Australian iron ore geological reconciliation system, in Proceedings Iron Ore 2017, pp 415–422 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Thomas A. Simpson

Traveling through the moors and valleys of Cornwall, England, one is reminded of the extensive mining activities of the past. Abandoned shafts, remains of granite block wheel houses and engine houses, battered brick stacks, old calciners, overgrown water wheel pits, count house remains, overgrown waste pits, and old portals are gaunt monuments to a once flourishing mining industry. Cornwall is bordered on the north by Devon and occupies the south-western most tip of Great Britain. The Atlantic Ocean borders the promontory; to the north, the mouth of the famous Bristol Channel faces the open sea; and to the south, the English Channel separates the land masses of Great Britain and Europe. This part of England is probably the most extensively mined ground in all of Europe. Such great mines as Dolcoath and Wheel Vor, Consols and South Carodan, Levant and Bottalack, remain legendary in the annals of metal mining in the nineteenth century. Many US mining districts hold close ties with Cornwall, Devon, and Wales through ancestors who emigrated from there to work in US mines in the eighteenth and early nineteenth centuries. Their descendants can be found in many major US mining districts, and their terms, expressions, customs, and methods have left an impact on the US mining scene that remains with us today.

Jan 9, 1981

By D C. McPhail, S L. Rogers, J Brugger

Using iron- and sulfur-oxidising bacteria to catalyse the breakdown of sulfides that host the gold is an important biological method for the pretreatment of refractory gold ores. Following this biological treatment a combination of chemical and physical methods are used for leaching (such as the cyanide process) and concentration (such as carbon-in-pulp or electrowinning) of gold. Although these methods are well accepted by industry, they harbour limitations in the processing of low-grade refractory ores, and regulatory agency/public acceptance of cyanide use. Thus, it is beneficial to industry to develop environmentally friendly, cost-efficient leaching and concentration techniques that are based on micro-organisms. This may soon be possible by adapting the results of recent regolith geoscience research, which has shown that micro- organisms are capable of driving a biogeochemical cycle of gold dispersion, transport and reconcentration in the supergene environment. The indigenous microbiota in biologically active soil microcosms from a number of Australian sites are capable of solubilising up to 80 wt per cent of the gold contained in these materials during 50 days of incubation. Studies using molecular microbial techniques have shown that a metallophilic bacterium, Ralstonia metallidurans, is present in biofilms on gold grains from a number of Australian sites. R metallidurans is capable of actively accumulating gold from solution, suggesting that the bacterium may contribute to the formation of secondary gold grains and nuggets. Identifying the biochemical and physiological pathways that lead to the dispersion and accumulation of gold in regolith, and quantifying the reaction kinetics of these processes may thus lead to the development of industrial bio-processing capacities for gold-containing ores.

Jan 1, 2007

By A. D. Davis, C. J. Webb, C. S. Johnson, J. L. Porter

The abandoned Belle Eldridge Mine near Deadwood, South Dakota, is on land controlled by the U.S. Bureau of Land Management (BLM) property. The mine produced primarily lead and zinc during the first half of the twentieth century. The BLM has expressed concern about acidic drainage as well as elevated arsenic levels in tailings and waste rock at the site. The mine site was evaluated for remediation in 1998 and 1999. Recent reclamation and remediation work included substantial regrading of waste rock, removal of material where metal loading were of concern, and re-routing of drainage from an adit. Trenching at the site shoed a greater volume than originally calculated during site characterization. Material was removed to a repository that was constructed at a nearby drainage divide. Because of physical hazards, the BLM has decided to remove some historic structures. However, a search of mine records and an inventory of archival materials were complete to preserve the history of the site.

Jan 1, 2002

Triboelectric Separation - Beneficiation of Coal The performance of triboelectric separators is highly sensitive to the selectivity of the particle charging process. This paper presents a quantitative study on triboelectric coal beneficiation. The performance of different charging media was studied. Stainless steel was identified as having a work function between that of coal and silicate gangue and found to be the optimum charging medium for coal beneficiation. Recent results from separation tests were performed where silicate gangue was separated from crude coal using a parallel plate free-fall separator are illustrated.

Sep 13, 2010

A review of historic mining information and geological literature pertaining to the Alpine Mine, Lyell Goldfield has been completed. As a result of this work the Alpine reef is inferred to be associated with an upright anticline with a sub-horizontal axis. Structural profiles prepared from limited underground data indicate that the reef is subparallel to the eastern limb of the anticline and cuts across the western limb. Reassessment of structural mapping completed by the New Zealand Geological Survey indicates that Greenland Group metasediments within the Lyell Goldfield are folded into a series of opposed assymetic folds with sub-horizontal axes. It is suggested that the anticline which harbours the Alpine Reef is located on the axis of a synclinorium. Along the western limb of the synclinorium the subsidiary folds have steep west dipping limbs and shallow east dipping limbs (western sense of assymmetry) whereas shallow west dips and steep east dips are typical of the eastern limb. The notion of quartz mineralisation occupying the axis of a synclinorium is contrary to the situation in the Reefton Goldfield where quartz mineralisation is affiliated with folds associated with an anticlinorium. Historic mine data reveals that below No.4 Level the quartz-gold mineralisation, in the Alpine Mine, occupied a steeply dipping ore channel. The strike of the channel was to the northwest and within this structure the are shoots plunged to the north at approximately 40¦. Archival mine plans show that two quartz bodies, the North and South Blocks, were present at No. 4 Level. Although the North Block was followed down to No 14 Level (530 m vertically below the surface outcrop) the South Block was only mined as far as No 7 Level. Sampling on No 7 Level together with the results of trial mining suggest that the grade of quartz underfoot in South Block is low. Information from the Mines Statements and mapping undertaken by the Gold Prospecting Scheme reveals that faulting had a profound influence on the intregity and extent of the Alpine Reef. The reef occupies a Inajor shear zone but little is known about it. It is also apparent that below No 7 Level the reef was progressively shattered by faulting and this may be the chief reason for the decrease in grade in the lower levels of the mine. No substantive facts are available about wall rock alteration effects adjacent to the Alpine Reef Still this is not surprising considering that comments on the mineralised pug envelope and breccias adjacent to the mined quartz shoots at the Globe - Progress Prospect were omitted from contemporary publications. In spite of this the existance of sulphide bearing reef casing lithologies cannot be completely dismissed since 9.15 m of 'reef track' has been reported in Reids No 2 Level.

Jan 1, 1996

By Campbell Brown GA

IN 1904-5 diamond drilling operations in the Mount Morgan mine proved the presence of some inillioils of tons of rich, copper-gold ore, averaging about 45% to 50% silica and 22%Fe as sulphide. To smelt this ore in blast furnaces, without previous concentration, large quantities of basic flux.were required. Unlimited quantities of cheap, limestone, were available at Marmor, on the GladstoneRockhampton railway, 50 miles from Mount Morgan, but the supply of iron flux was a more difficult problem. Smelting operations started, with one' furnace in January, 1906, using as flux low-grade sulphide ore fro:m. the mine, containing very little silica. When the second, furnace was blown in this was supplemented by ironstone from, small aeposits in the immediate district. It was recognized that these sources of supply would be insufficient to keep the full plant going after the third furnace had been blown in. Accordingly, the deposits at Eabra and Mount Etna were opened, neither of which proved capable of supplying the quantity required viz, 1000 tons per week. Negotiations were meanwhile being conducted with the Marble Island Iron and Limestone Co. to obtain the right to mine at Iron Island, where a sufficiently large deposit was known to exist. Shipments from this source commenced in January, 1907, and ceased at the end of July of this year, when the metallic flux from...

Jan 1, 1912