Search Documents

By Bain J. H

Since zinc was first deposited at Risdon in February, 1917, provision of the most economical cathode assembly has been a subject of extensive research, the major problems being corrosion and efficient use of power.From the corrosion viewpoint, a perfect cathode is one in which the life of the headbar and the deposition sheet are the same. However, corrosion usually concentrates in a narrow zone across the face- of the sheet, resulting in breakages which, before the advent of argon arc welding, meant a loss of a 'complete assembly.Attempts to extend sheet life included use of thicker sheets, multitudinous protective coatings applied with varying degrees of success, re-rolling, and for a time, aluminium consumption was reduced when broken sheets found re-use as protecting strips. This latter economy became impracticable when electrode spacing was reduced for greater efficiency in power utilization.As an integral part of the electrode, the headbar was modified accordingly. Copper headbars, although more corrosion resistant, were replaced by aluminium due to a possibility of dissolved, copper promoting deterioration.Thicker electrodes and regulated spacing reduced internal shorting, whilst provision of knife-edge type supports on both contact and insulator ends of headbars aided in electrode centralising and continuous electrical conduction.After much experimeIitation, an assembly has been evolved which, with the aid of argon arc welding and tbe use of minimum additional aluminium, permits comparable headbar and sheet lives, combined with good electrical conduction throughout the life of the cathode.INTRODUCTION Over 300 tons of zinc are produced daily at Risdon from a purified zinc sulphate solution by electrolysis, the zinc being deposited upon all-aluminium (except for copper contact) cathodes. It is stripped in 72-hour cycles from the cathodes, melted and cast into the customary rectangular slabs.

Jan 1, 1958

By R. Craig Smith

This report presents the software documentation for PREY AL, a prefeasibility mineral property evaluation program developed by the U.S. Bureau of Mines on a Lotus 1-2-3 spreadsheet. It is presented in a step-by-step "user?s manual" format. Appendixes contain the technical assumptions, program default values, and a summary printout detailing capital and operating costs and cash-flow analysis.

Jan 1, 1992

By Porfirio Pinto Linares

El presente texto señala la paragénesis y mineralización del distrito de Morococha. Dicho distrito está situado al Este de Lima, en el Perú central y sus principales productos minerales son el cobre, zinc, plomo, plata. Su mineralización está relacionada con el intrusivo del mismo nombre, encontrándose el centro más efectivo de la mineralización en el stock San Francisco, mientras que la paragénesis observada en las estructuras estudiadas es compatible con el zoneamiento existente; ya que las primeras capas depositadas son de cuarzo y pirita, siguiendo la esfalerita, enargita, calcopirita, tetrahedrita, esfalerita y galena; rellenando las cavidades se encuentran los carbonatos.

Mar 1, 1965

By Henry Kreisinger

Some of the investigations conducted by the Bureau of Mines have for their object the collecting and disseminating of information regarding methods by which the fuels of the country may be most efficiently used. As the analysis of flue gases tends to develop better methods of firing, which in turn reduces waste of fuel, the Bureau of Mines in this bulletin presents for the benefit of those in charge of boiler plants and all other persons interested detailed information on methods of sampling and analyzing flue gases, and on the utilization of the analyses in promoting boiler-room economy. This bulletin is intended to be a companion to Technical Paper 80,a and is written in plain and nontechnical language, as far as possible, so that it may be readily understood by persons who have not had the advantage of a technical education. Whenever possible, illustrations of apparatus and methods of handling have been used rather than elaborate descriptions.

Jan 1, 1915

By José Farfán

La minería artesanal y a pequeña escala (MAPE) se caracteriza mayoritariamente por su informalidad, no obstante, tiene la capacidad de generar riqueza y desarrollo en los distritos más alejados y constituye una alternativa de empleo para miles de personas. En el artículo se detallan las dimensiones, características de producción y comercialización de las MAPE en Perú, y se ofrece una visión integral del proceso orientado a alcanzar su formalización.

Jul 30, 2020

By J. W. Allen

This report reviews the work performed on Task M of Bu-Mines Contract H0220073 to develop an engineering model of a surface and subsurface communications system for normal mine operations and for post disaster rescue operations. The system concept provides for one-way transmission of digital information between a number of identifiable subsurface terminals or subcenters and a single surface station. It also provides 2-way voice communications between the subcenters and the surface station. The basic communications link is electromagnetic signaling through-the-earth, but the system is also capable of using mine phone lines as an alternate link. Engineering models of three subcenters and one surface terminal (see Figure 1-1) have been fabricated in order to demonstrate the system's performance. The system concept, however, permits up to 20 subcenters to be incorporated if desired. Additional subcenters are also feasible for large mines if they can be deployed in the mine to operate on a noninterfering basis.

Jan 1, 1973

By M. W. BERNEWITZ

AUSTRALIANS and New Zealanders, whose countries have respectively yielded gold to the value of £666,000,000 and £96,000,000, are taking full advantage of the current high prices for that metal. There is a marked activity in ordinary prospecting, geophysical exploration, further development of working mines and reopening of old properties, formation of new companies, installation of new equipment and processes, and expansion of operations generally. Australian gold production last year was approximately double the quantity of 1929 and its value three times as great, 1929 being the low of recent years. The 1933 production was about 821,000 oz. From New Zealand, 165,000 oz. was exported last year. Papua and New Guinea contributed slightly over 100,000 oz. What the future price of gold will be nobody knows, but, even if it returns to the former level, Australian producers are almost sure of 110 shillings an ounce until 1940 through the Commonwealth Government's Gold Bounty Act, at present temporarily and necessarily suspended from operation.

Jan 1, 1934

By H. A. Doerner

"The following report is submitted, in compliance with the request made by the Honorable W. H. Sproule, Chairman of the Committee on Mines and Mining, to the Director of the United States Bureau of Mines, that the bureau investigate the most modern processes for the production of radium from its ores. A thorough search of technical publications and patent office files was made. Outstanding authorities on the subject as well as persons claiming novel or secret methods were interviewed.Unlike most other elements, it is not possible for radium to occur naturally in a pure or concentrated form. This is because radium is one of a series of unstable elements which, by a constant, spontaneous, atomic disintegration, change from one element to the next in the series. Uranium is the ""grandparent"" of radium. The rates at which radium atoms are ""born"" and ""die"" are so related that only one part of radium can exist in equilibrium with three million parts of uranium. Consequently radium is only found associated with uranium minerals, and the ratio of radium to uranium is never more than one to three million. Since uranium is a rather rare element, the scarcity of radium is almost beyond comprehension. Nevertheless minute traces of radium can be detected in nearly all rocks.The carnotite ores of Colorado and Utah were the chief source of radium for many years.In the fall of 1922 news of the very rich deposits of radium ore discovered in the Belgian Congo caused most complete cessation of domestic production. The Congo ore contains pitchblende and a number of alteration products, including the new minerals bequerelite, curite, krasolite, stasite, and dewindite. Reports indicate that a considerable amount of ore containing over 50 per cent uranium oxide has been produced. It seemed certain that radium could be extracted from the Conga ore at a much lower cost than from the relatively low-grade carnotite; and in order to preserve their elaborate marketing organizations, the larger American producers made agreements with the Belgian syndicate to market the foreign product in this country. The retail price of radium has been held at $70 per milligram, but large orders are filled as low as $50. Extraction of radium from carnotite by the usual methods does not appear to be profitable at that price with one exception, all American firms ceased production after their accumulated stocks of ore had been treated. The United States Radium Co., which continued to treat carnotite for several years, finally shut down its plant."

Dec 1, 1930

By Aníbal Gatañaga Coll

Dada la peligrosidad del sílice libre como principal problema en el campo de la higiene industrial, el objetivo del trabajo es controlar y evaluar la concentración de dichos polvos a través del uso de tres métodos: El método químico, el de difracción de rayos X y el petrográfico. El primero (N. A. Talvitie), utiliza un reactivo que descompone y disuelve a todos los constituyentes de la muestra, excepto al cuarzo, quedando calcinado y filtrado; el segundo método es eficaz, pero requiere de un equipo muy costoso, mientras que el método petrográfico muestra una mejor identificación de los minerales, determinando las cualidades de los materiales que se producen en la composición del polvo, así como precisa la pequeñez de las partículas encontradas en los polvos industriales y sobre todo de la capacidad del operador.

Jul 20, 1955

By Medardo Echegaray

Desde el punto de vista de análisis químico se buscaba estudiar un método de determinación de fierro que ofreciese una buena precisión en una zona de concentraciones. En ese sentido, el presente texto señala la determinación colorimétrica del fierro a través del método de complejo aceto-férrico. No existe intlerferencia por el manganeso, fluor o níquel. El cromo interfiere cuando se encuentra en cantidades mayores a su máxima concentración permisible o sea 0.1 mg .

Mar 1, 1963

By Daniel Palacios N

El proceso de industrialización del Perú se rige por la demanda de materias primas minerales, para las cuales se exigirá una óptima calidad y precios competitivos. Para contrarrestar esta demanda, es necesario el manejo adecuado del aprovechamiento de los recursos minerales naturales en los yacimientos mineros y así valorar las disponibillidades de los mismos a escala nacional. En este sentido, el objetivo del texto describe la aplicación del programa de no-metálicos que el Departamento del mismo programa INGEMMET propuso.

Oct 14, 1980

Casing or lining pipe is used in boreholes for the following reasons:1. To preserve the hole while drilling and after it is finished.2. To shut water out of the hole or to isolate any particular water, gas, or oil-bearing stratum.Deep holes can seldom be drilled without casing, and only when in firm strata. If caving from the walls is at all likely while drilling, casing is necessary in order to prevent the tools horn being buried...

Jan 1, 1924

By K. E. Barnes

"The “Jameson Cell” flotation cell was developed at Mount Isa Mines in the late 1980’s to address deficiencies in our flotation column installations. Early base metal installations had a variable record. The test work and trials showed they made an improvement metallurgically when operated correctly, but performance of the early installations was hindered by a range of operational and maintenance issues. The installations needed to be more robust, and we needed a better understanding of how to successfully integrate the cells into the plant flow sheet.During the 1990’s, Jameson Cells had great success in coal fines flotation and organic removal in SXEW applications, and became the standard in these applications in Australia. These installations improved the cell design and materials of construction and the cell flow sheet design, to make it low wear with self-regulating control, producing good performance with little operator input.These improvements have enabled a fresh look at the use of Jameson Cells in base metals. Recent new installations have shown significant benefits in “hybrid” circuits, that combine the best features of both Jameson Cells and conventional flotation cells, achieving better overall circuit performance in a smaller footprint than either technology could do by itself.Case studies of successful base metal applications are discussed, using size-by-size mineralogical performance to explain the improved circuit performance. The new methods of flow sheet test work design are also described."

Jan 1, 2006

By Carolina Ayala

Dado que las empresas enfrentan escasez de recursos, materias primas, y exigencias ambientales o laborales; la sociedad también enfrenta fenómenos de movilidad social. En consecuencia, el crecimiento de las empresas se ve influenciado por las exigencias de los grupos de interés. En ese sentido, el presente texto señala que la relación de empresa- sociedad debe ser de coexistencia y búsqueda de beneficios mutuos. Sus principales objetivos son: disminuir y mitigar impactos, asegurar y cuidar recursos escasos y la creación de nuevas realidades que generen un valor superior.

Jul 1, 2013

By C A. Locke

Geophysical signatures of the Taranaki and Tongariro volcanoes reflect similarities in their age, composition and hydrothermal histories, but also reflect differences in host rock settings and edifice evolution. The Taranaki volcanoes have strong positive gravity anomalies showing that their edifices largely consist of dense andesite which reflects substantial lava production or dyke injection during construction and that large sub-edifice dyke/stock complexes occur. In contrast, the Tongariro volcanoes have strong negative gravity anomalies indicating low density edifices of volcaniclastic material; no sub-edifice intrusions can be identified, probably because of the lack of density contrast with host basement rocks. Strong positive magnetic anomalies over the younger cones can mainly be attributed to near-surface andesite lavas or dykes whereas subdued magnetic effects are associated with hydrothermally altered zones within both edifices and sub-edifice intrusions.  

Jan 1, 1995

By A. L. Podia

The purpose of this research was to develop a system capable of detecting changes in the structure of rocks, leading to failure of mine roofs, and/or excavations. A prototype system was developed, field tested and delivered to the United States Bureau of Mines for further evaluation and research. This system is based on the analysis of acoustic signals generated on the surface of the roof by an impact device and which are reflected or backscattered by flaws and discontinuities in the rock. The specially designed impact source is capable of generating high frequency acoustic signals with excellent repeatability. The system can also be used in conjunction with conventional acoustic pulse transducers. The received signal is digitized and the data transferred to a minicomputer for processing and display. This capability allows the immediate determination of wave velocity and/or distance to a reflecting interface. Various data processing techniques such as averaging, differentiating, and comparing of different signals can be selected by entering the appropriate commands on the keyboard. Being a programmable system it is possible to implement more advanced signal processing techniques. All results as well as the signal are displayed on a CRT. Furthermore, a permanent record of the data can be generated on paper tape, which can be reentered and processed at a later date. A communications interface allows transmission of the sampled signal to a large scale re-mote computer. The system was tested extensively in the laboratory, and field tested at the York Canyon Coal Mine. These tests proved the feasibility of operation in the mining environment. Results indicate that further investigation and development will have to be undertaken to fully develop the potential of this system in satisfying the goals of this research.

Jan 1, 1973

By Ronald S. Conti

A new U.S. Bureau of Mines 6.8-L ignitability furnace was used to study the thermal autoignitability of dust clouds. This furnace has a quartz window to allow observation of the early stages of the ignition process and to allow measurement of the dust explosion temperature. Thermal ignitability data were obtained for various carbonaceous and metal dust clouds, with particular emphasis on various ranks of coal dusts. One of the reasons for the construction of the new 6.8-L furnace was to evaluate the effect of chamber volume on the measured autoignition temperatures. Therefore, data from the 6.8-L furnace were compared with data measured earlier in a 1.2-L furnace. The conclusion is that the autoignition temperatures measured in the 6.8-L furnace were only slightly lower on average than those from the 1.2-L furnace. These data on the minimum autoignition temperatures of various materials will be useful in analyzing the thermal ignition hazards of dust clouds in the mining industry and other industries that manufacture, process, or use combustible dusts.

Jan 1, 2010

By D. W. Rich

An environmental management system (EMS) is a key part of a company?s environmental stewardship. Procedures and practices to continually improve environmental performance can provide great benefits in operating the company. Managing site environmental quality data is a key component of this. An environmental data management system (EDMS) is an important element of the EMS for mining and other projects, providing project staff with the information that they need to make decisions that can have a significant impact on public health. Improvements in computers, data communications, and transfer formats have made it much easier to implement an integrated EDMS program for gathering, managing, selecting, and displaying data from the field and the lab. Software now lets users define sampling plans, create files for field data entry, and print Chains of Custody. Laptop and handheld computers facilitate field data entry and may provide automated communication back to the office. Most labs can now create usable electronic data deliverables. QC checks and limit comparisons can be largely automated. The result is organized data that can be efficiently used for reporting, graphing, and mapping, to better understand project issues.

Jan 1, 2009

By César Augusto Martín Hilser Vicuña

El "Punto de fluencia” es el contenido de humedad crítico a partir del cual un mineral concentrado sufre “liquefacción”, es decir, libera la humedad como agua libre al ser sometido a las sacudidas propias de una travesía por mar. En esta perspectiva, el presente texto correlaciona la influencia que tiene el proceso de producción de los concentrados en el punto de fluencia a través de los siguientes factores: granulometría, efecto de los reactivos de flotación y la mineralogía. De forma que al conocer los factores que influyen notablemente en el valor de la humedad límite de transporte, se evita los riesgos de que la carga sufra licuefacción durante su transporte por mar.

Sep 14, 2009

The revised estimate of coal production in January 1977, is 39 million tons -- down 12 mi 11 ion tons compared with production in January of last year, largely as a consequence of the snow storms and cold. The major coal-hauling railroads operating in Eastern and Midwestern States reported to the Bureau of Mines that they loaded approximately the same number of cars for the week ended February 5, as in the preceding week. The Bureau of Mines estimates that U.S. coal production for the week ending February 5, 1977, was approximately 8.5 million tons, or nearly 3.5 million tons less than production for the corresponding week in 1976. Coal production from January 1 - February 5, 1977, was approximately 47.8 mi 11 ion tons compared with production of 63.5 million tons for the corresponding period in 1976. As of the first week in February, river and truck shipments of coal in the Eastern U.S. were about one-half of the normal traffic. Despite the freezing weather and ice and snow conditions of rivers and highways and reduced rail shipments, there was reportedly little or no shortage in coal supply to consumers. Inventories at electric utility plants and steel company coke plants at the beginning of the severe weather were sufficient in most cases for at least 30 days" operations. There have been no reports of coal shortages at other industrial plants.

Jan 1, 1977