Search Documents

At Copper Refineries Pty. Ltd., Townsville, two reverberatory furnaces of 420 tonnes capacity are used to melt 210000 tonnes/year of copper for subsequent anode casting. When the refinery commenced production in1959, these furnaces were of 300 tonnes capacity. The original furnaces featured a silica brick hearth, magnesite and chrome magnesite side 'walls, and a sprung silica brick roof, but were unsatisfactory because of thelow refractory life and high costs. With continuous expansion in production and the incentive to increase furnace life and capacity the design of these furnaces has changed greatly since that time.The present furnaces feature all basic brick, a flat suspended basic brick roof, very extensive use of watercooled copper sections, and are of substantially increased (420 tonnes) capacity. Particular attention has been concentrated on high wear areas such as the taphole, side walls, and charging door jambs. Each furnace in its 24 h cycle, is charged, the copper melted, impurities skimmed off, metal "poled" prior to casting, and cast.The service condition during each of these operations is important in considering furnace refractory life.The improvements in operating practices and furnace 'construction which enabled the capacity of the furnaces to be increased are discussed. The life between major repairs to side walls has increased from 90 charges to300 charges.The scope for future improvement is considered and areas for development are suggested.

Jan 1, 1977

The reconstruction of the world after the present war must inevitably be profoundly influenced by the rise and progress of New China.The principle of Chinese mathrity has been admitted by Great Britain and the United States by their abjuration of extra-territorial tights, and by the withdrawal of the Maritime Customs Administration. The United States admits equality by her declaration that Chinese are eligible for American citizenship, and the reaction to this will be swift enmity to such peoples as may impose humiliating restrictions upon Chinese citizens.Finally, the decisions of the Moscow Conference and the recent meeting of National leaders in Cairo give partnership rights to this new State in post-war reconstruction, and open the way for a rapid realization of her destiny.It seems certain that China, if so she wills, can become, within a generation or so, one of the considerable forces of the world. The toad she wiII follow will be lighted by her own inherent and intrinsic genius. Her speed of progress can no longer be forcibly influenced by other nations and the attitude towards her of somewhat contemptuous patronage hitherto adopted by the European communities bordering the Pacific Ocean must be radically modified.It is doubtful whether the European will ever reach full understanding of Chinese mentality. The Chinese "way of life" since the dawn of her civilization has been totally divergent from that of the European, but the enormous potential strength, due to the simplicity of their requirements and their steadfast industry, is a function of that "way of life." On the other hand the trend of reorganization must obviously be towards Western standards; and a wide knowledge of the potential strength of the Chinese is possible and will be essential in our post-war world. The following, necessarily inadequate, notes are therefore offered, as an indication of the obstacles to be overcome and the capacity of the Chinese executives and operatives to overcome them.For 'thirteen centuries the political and social structure of China proper (ie, excluding Mongolia, Manchuria and Tibet) has been rigidly shaped by the philosophy of Lao Tze and the ethics' of Confucius. This Taoism, which is described as the "way of harmony" with its three jewels of character, gentleness, economy and humility, advocates the minimum of social, economic and political organization and still gives the key to the Chinese character.The Mongol and Manchu conquests of the 12th and 17th centuries, respectively, could hardly be dignified with the name of war, but the superior intelligence and harder mentality of the unwarlike Chinese finally absorbed...

Jan 1, 1944

By W Valery, A Jankovic

The ball mill in closed circuit with hydrocyclones is an industry standard, and well known methodologies exist for equipment sizing, selection and design. However, the potential to improve the capacity of ball mill circuits by replacing cyclones with screens has been recognised for many years and recently has been successfully realised, thanks to developments in fine screening technology. Proper methodology for equipment sizing and selection is required to capitalise on this opportunity, but there is currently insufficient information and few guidelines available on how to design such a circuit. This paper discusses the differences between ball mill circuits closed with cyclones and with screens. A methodology is described for equipment sizing and selection for a circuit closed with screens, and the laboratory testing requirements are described for low grade base metal ores and magnetite ores. An economic evaluation is also presented for a case study demonstrating the potential benefits of closing a ball mill circuit with screens.CITATION:Jankovic, A and Valery, W, 2013. Energy efficient ball mill circuit - Equipment sizing considerations, in Proceedings MetPlant 2013 , pp 285-295 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Frank J. Arland

Augered-Cast-in-Place piles have been used successfully for many deep foundation applications. The four case studies discussed herein describe ACIP pile projects where problems developed during ACIP pile installation requiring changes to the method or sequence of installation. The case studies illustrate the importance of understanding existing subsurface conditions and project constraints when considering the use of this pile type. Ground loosening and over-excavation of soil during the augering process, a significant concern for fine to medium sands and non-plastic silts below the water table, can significantly impact adjacent structures. This risk needs to be evaluated during the pile selection process and generally can be mitigated, but not eliminated, by requiring the use of piling equipment with high torque and slow auger rotation speed to advance the auger with minimum amount of rotation. In some applications where high lateral stresses in the soil are present such as at the base of retaining structures, the use of ACIP piles may not be appropriate if structure movement is unacceptable. On the other hand, ACIP piles have been successfully used to support deep foundations in preconsolidated varved deposits where the new structure was designed to accommodate recompression settlement.

Jan 1, 2004

By Narasimhan K. S, Sastri S. R

A typical high silica low grade magnesite from the Salem area of Southern India, was used in studies to develop a suitable flotation system involving commercially inexpensive sodium oleate as the collector together with other reagents which can give a product of the required grade with an acceptable recovery. It was found that the presence of metallic ions such as Cu+, Fe+++ or Ca++ introduced by the addition of their salts, or by their formation with the addition of hydrochloric acid to react with magnesium and calcium carbonate in the me, can act as effective depressants for silica. The addition of 'hydrochloric acid' was found to give best results.

Jan 1, 1980

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

YOUR mom was right …count to 10. Most workers today report that they find their jobs stressful. Miners, in particular, are faced with hazardous and changing environments. Every shift provides different conditions and challenges. Coping with stress is an important tool to maintain your physical and mental health. Now, back to mom. Studies on stress tell us that shifting your focus away from what is causing your stress increases your ability to cope. Counting to 10 is one method. Science proves mom right. The stress response We are born with the stress response, which is a survival instinct, sometimes called the "fight or flight" response. When approached by a tiger in the jungle, our ancestors would perceive danger and prepare to fight or run. The body prepares for the fight or flight response in a number of ways. The bloodstream brings extra glucose and oxygen (fuel) to the heart, the sense of pain is dulled, and memory and thinking improve. The pupils dilate for better vision and the lungs take in more oxygen, while heart rate and blood pressure increase. Body hairs become erect, as puffed-out hair makes an animal look bigger and more dangerous. Once the perceived danger is gone - we have run fast enough to get away from the tiger or won the fight - the body returns to normal functions. Unfortunately, civilization gives us too many opportunities to experience this response. If activated too often, it can create wear and tear on the body, which may lead to injury and illness. Chronic and traumatic stress There are two key types of stress: chronic stress and traumatic stress. Both types can cause both physical and psychological symptoms. Chronic stress builds up from the day-to-day hassles. Traumatic stress results from a traumatic event such as a natural disaster, a mine disaster, or the sudden death of a loved one. Chronic stress is associated with an increased risk of a number of health problems including heart disease, depression, back pain, and carpal tunnel syndrome. Traumatic stress may lead to post- traumatic stress disorder (PTSD), Miners may experience both chronic and traumatic stress in their work.

By Andrzej Tejchman

Calculation of pile foundations should possibly truly reflect its real work, mainly with respect to the value and distribution of settlements, pile internal forces and bending moments within a slab. Many empirical and theoretical methods serving for an assessment of the settlements of pile group overestimate its actual values obtained from field measurements (see Tejchman et al., 2001). In the paper a simple engineering method for calculation of pile foundations is presented. The method takes into account the interaction between the slab and a soil together with the phenomenon of non-uniform deformation of the soil-pile subsoil, particularly under large foundations. In the method the scheme of the slab resting on one-parameter elastic subsoil is assumed. The comparison of the calculation results for existing pile foundation with the field measurements shows good agreement between those values.

Jan 1, 2002

By Frank Callanan

The Ameristar Casino expansion project included the design and construction of a 25-story hotel and 9-story parking structure expansion. The site is located in a floodplain on the banks of the Missouri River in Saint Charles, Missouri, where the underlying soils are potentially liquefiable. The geotechnical engineer performed subsurface exploration and analysis, which included site-specific seismic response and liquefaction, and provided geotechnical design recommendations. In the event of an earthquake, post-liquefaction settlement was calculated to be approximately 14 inches. Additional project constraints included wetlands protection, construction adjacent to the existing facility, flood protection and river bank stability. Because of the liquefaction issue, the geotechnical engineer consulted with a specialty geotechnical contractor on ground improvement methods. This consultation led to a proposal to eliminate deep foundations from the design and support the structures on shallow and mat foundations. The geotechnical engineer assisted the design team with foundation design analysis and value engineering assessments. Together with the project team, the geotechnical engineer used the data to evaluate foundation options and construction methods to overcome the site challenges and concluded that ground improvement was the optimum course of action. Because of the nature of the site constraints, a number of ground improvement methods were needed. The geotechnical engineer evaluated the methods proposed by the geotechnical contractor and provided the technical specifications for the ground improvement bid package, which included vibro-compaction, compaction grouting and micropiles. The ground improvement allowed for the use of shallow foundations (mat and spread footings), which provided the client with significant time and cost savings over the deep foundation alternatives.

Jan 1, 2009

By Rao P. K, Sahoo P. K

The main constituents of ferromanganese slags are silicates of Mn, Ca and AI. Factors affecting the recovery of manganese from a low manganese content ferromanganese slag (about 16 per cent MnO) during acid leaching were studied. These included time, temperature, agitation, sulphuric acid addition, solid:liquid ratio and particle size. Agitation rates greater than 300 rev/min. leaching periods greater than 30 min and temperatures above ambient were found to have no effect on Mn recovery. Dissolution of Mn was found to be highly dependent on the amount of acid added.About 90 per cent of the Mn was recovered when 5·5 times the stoichiometric amount of acid was used. About 28 per cent of the Mn was recovered when the stoichiometric quantity of acid (with respect to Mn alone) was used. However, the recovery increased to about 75 per cent when the total stoichiometric requirement of acid with respect to Ca, Al, Mg and Fe as well as Mn was used for leaching. The extent of Mn dissolution also depended on the particle size of the slag. The percentage of Mn recovery (using 5·5 times the stoichiometric amount of acid) increased from about 60 per cent to about 92 per cent when particle size decreased from -36 +52 to -150 +200 mesh (B.S.S.). When the results of this study were compared with those in a previous study involv,ing the leaching of a high manganese content slag (containing about 40 per cent MnO) results were similar except that there was a gr-eater consumption of acid in the present case (i.e. low manganese content slag).

Jan 1, 1979

In order to reach a large, untapped reserve of high-quality coal, D8 Cloverlick mine proposed to mine a corridor nearly 2,000 ft deep beneath the Benham Spur of Black Mountain, Kentucky’s highest peak. D8 Cloverlick mine was extracting the Owl seam, but the corridor’s route lay approximately 70 ft above century-old mine workings in the C–(Darby) seam. Adding to the concern, three serious coal bursts had recently occurred in nearby Owl seam workings.

Jan 7, 2020

Following the experimental work of Denny, Robson, and Irwin, and the clinical investigation by Crombie and Blaisdell, an investigation of aluminium therapy was begun at Washington, Pa., which is situated In a very large industrial section of the State. Some of the men to be studied were from plants manufacturing silica brick, refractories used in steel and glass manufacturing, and semi-porcelain table-ware; others were workers in foundries, sand blasters, and men engaged in the quarrying of ganister rock.This group of workmen gave an opportunity to study the effects of aluminium on various types of silicosis which differed somewhat from that found in hard-rock miners.EXPOSUREIn their occupations, the men studied were exposed to silica dust concentrations ranging from 17 to 97 per cent free silica. In the silica brick industries, the unfired product averages 96 per cent silica in the form of quartz, whereas the fired brick contains 50 to 62 per cent. cristobalite plus 11 to 80 per cent. tridymite, forms of silica that, on account of their higher solubility, are more toxic than quartz. The operational dust counts in the plants varied from 15 to 9,500 particles per c.c., and the median particle size from the aerial samples was 1.0 micron for the green product and 2.0 microns for the fired product. The length of exposure varied with the occupation as well as with the individual plant, but disabling silicosis could be produced in less than four years in certain exposures. The average time needed to produce radiological silicosis in those susceptible to this disease was eight years. Some of the men in our series of cases have been treated as long as fifteen years after exposure had ceased, and have improved under treatment.The dust counts mentioned above had been reduced prior to the aluminium therapy studies and the presen.t exposures do not exceed '900 particles per c.c., the average being 370 particles. per c.c. This improvement in dust conditions was due to improved dust control apparatus, which was installed before aluminium therapy was instituted. Aluminium powder is not a substitute for dust control.PATHOLOGYThe pathological picture of silicosis in men engaged in the ceramic industry is somewhat different from that in hard rock miners." Due to exposure to high concentrations of dust containing high percentages of silica of varying degrees of solubility andvery small particle size, these men are subject to a relatively rapid type of silicosis, which sets up an acute...

Jan 1, 1945

By John Watson

The earliest known records related to mining document in dramatic terms the fact that mining methods have undergone significant change over the centuries. Wooden wedges, hammers and chisels, “fne setting”, to name a few, were the frst tools used to extract ore .or quarry rock for civilization. These inefficient tools and unsafe practices have been replaced today with some of the highest technology known to man. At the heart of most mining operations is the blasting program which utilizes one of the most efficient tools ever invented.. . explosives. Ever since they were invented, miners have been searching for more efficient products and methods with which to harness this “tool” and make it safer, reliable, and more eficient to use.

Jan 1, 1997

By M. Arvola, A. Mäkinen, N. Isomäki

Arsenic is a compound that has no significant market value. However, it needs to be removed from ores, concentrates and other process streams because of environmental or technical processing concerns. A wide range of arsenic containing minerals exists in nature, and in many instances these minerals are also associated with the ones that have commercial value. For example, sulfide copper ores are normally closely associated with minerals like enargite, Cu3AsS4 and tennantite Cu12As4S13. After mineral processing these arsenic sources can report to the waste waters and these effluents need to be treated before discharge or recycling. Ferric arsenate precipitation is a well-established method for stabilizing arsenic in effluents. Electrochemical arsenic removal utilizes the same adsorption/precipitation ideology as ferric arsenate precipitation. Electrochemical arsenic removal, even though it is a simple process in terms of equipment, is a complex system involving chemical and physical mechanisms taking place simultaneously to remove dissolved and/or solid arsenic components from wastewaters. The whole process can be described by the following three steps: 1) electrolytic oxidation at a sacrificial anode (dissolving electrode metal, iron for example), 2) chemical reaction between dissolved iron and arsenic to form a solid precipitate and 3) aggregation of the particles to form flocs, which can be removed by known solid/liquid separation methods. Electrochemical arsenic removal is a very efficient way to remove arsenic from different waters to very low residual concentrations.

Jan 1, 2016

By F E. Grader

A linear motor properly wound can serve as a mechanism for separating paramagnetic sulphide minerals, like pyrrhotite, from other sulphides and associated gangue minerals. The effectiveness of separation depends on the energising current of the separator, the frequency of the ac cycle, and the particle size of the minerals. The speed of travel of the minerals over the surface of the separator is also a function of particle size, and appears to be constant. The movement of pyrrhotite, magnetite and iron filings of comparable size fraction (150 ¦m +74 ¦m) on the linear motor surface has been observed using a cine camera. An attempt, has been made to give a theoretical basis for the movement of the particles by calculating the minimum electrical energy required to move them. Further, the rate of decay of magnetic moment of the particles has been estimated for magnetite and it has been found that sufficient residual magnetism existed in the particles after they had been exposed to the first half of an ac cycle for them to have like polarity with the second half of the cycle. The particles are therefore repelled from the motor surface every second half of the cycle. This repulsion due to remanent magnetism is the probable cause of particle movement over the linear motor surface.

Jan 1, 1980

CAPTAIN JOHN H. BALLAMY John H. Ballamy, Captain on the Regimental Staff of the 103d Engineers, was killed near Fismes, on August 9, 1918. Captain Ballamy was born at Plymouth, Pa., in 1886 and graduated from the High School of that town in 1903. In the following year he began work as a coal miner, and at the same time began the study of mining engineering in the evening and any other spare time. He continued this diligent and energetic practice for many years. For sixteen years he continued in the employment of the Delaware, Lackawanna & Western Railroad Company's coal mining department, first as a practical miner, next as rodman on the survey corps, of which he soon became chief, then draftsman and mining engineer in the company's office. In January, 1916, he was promoted to the position of district engineer in charge of mining engineering work. He became a member of this Institute in September, 1917. CAPTAIN JOHN H BALLAMY. Captain Ballamy's military experience began at the same time as his engineering practice. He was a charter member of Company A, Engineers, N. G. P., which was organized ten years ago. He saw service on the Mexican border as First Lieutenant of this Company, and remained in that position until November, 1916. In July, 1917, he was again called into service and was sent to Camp Hancock, Ga., with the 103d Regiment of Engineers. Before joining this regiment he attended a school for officers at Fort Sill, Okla., where he received special training in field fortifications. In December, 1917, he was commissioned Topographical Captain on the Regimental Staff, and in April, 1918, preceded his regiment by about six weeks to France, where he again attended an officers' training school. He rejoined his regiment on July 15, near Chateau Thierry and was killed near Fismes on August 9, 1918.

Jan 11, 1918

By José Arango

El presente texto describe la aplicación del sistema MIMS en las estadísticas de producción de la Sociedad Minera Cerro Verde S.A. El sistema fue instalado inicialmente para el control de mantenimiento de los equipos, movimiento logístico, y contable. Posteriormente, se realiza el cambio del sistema de información manual a un sistema computarizado, donde se analiza los problemas cotidianos del sistema de información antiguo y se los compara con los cambios experimentados. En ese sentido, el objetivo de este sistema es facilitar el alcance de sus metas a la organización mediante el uso eficiente de todos sus recursos disponibles: personas, información, equipos, tecnología, y materiales diversos. La eficiencia de la utilización del recurso de información es medida por la relación del costo para obtenerla y el valor del beneficio derivado de su uso.

May 25, 1998

By Faan Bornman

"Reeves and Platt1 stated that dense medium separation is one of the most complex unit processes in mineral processing today particularly if cyclones are used. It is also the most efficient gravity concentrating process available to process engineers. The complexity of the process and large number of design and operating variables means that the process has largely remained more an art than a science. Dense medium separation is well established in the diamond, coal and iron ore industries but is gaining popularity as a pre-concentration step in other industries. The maintenance issues are addressed that will affect the efficiency of the operation.INTRODUCTION The purpose of the dense medium separation (DMS) process is to separate the valuable material from the waste based on gravity differences. However, the specific gravity difference between the two fractions must be large enough to achieve high efficiencies. Heavy particles sink through the dense liquid and light particles float. DMS is also used for the pre-concentration of minerals before further downstream processes like communition, in order to minimise the treatment costs. Examples are the pre-concentration of diamond ores or metalliferous ores like nickel, copper and cobalt. Dense medium separation is also used to upgrade the material to meet different market specifications, for example in coal and iron ore applications. A typical dense medium separation process for a diamond application is shown in Figure 1."

Jan 1, 2014

It is the purpose of this paper to produce some evidence on the accuracy to be expected from normal assay procedure using the usual first class equipment, and to examine the effect that many assaying inaccuracies have on reported metallurgical recoveries.Generally speaking, the evaluation of the gold content of a mineral ore sample by the fire assay method is a relatively simple process.A weighed quantity of finely ground ore is fused with suitable fiuxes including litharge and a reducing agent to give a button of lead and a quantity of slag. The shower of lead produced by the reduction of the added litharge collects the gold and silver present in the ore, concentrating the values into the lead button.The button of lead, after separation from the slag, is, on heating in an absorbent cupel in a current of air, reoxidised to litharge and absorbed into the cupel leaving a gold and silver bead in the cupel. This bead' is heated in a solution of nitric acid to dissolve the silver, leaving the gold undissolved to be dried and weighed. Knowing the original weight of the ore and the weight of the gold prill the value of the ore is easily calculated.Summarising1. Fusion Process.-Ore plus fiuxes give a slag plus lead button.2. Cupellation Process.-Lead button is re-oxidised to litharge leaving a gold and silver bead.

Jan 1, 1952

By Tyler Acorn, Brandon Wilson, Jeff Boisvert

Scenario-level uncertainty is a representation of large-scale differences encountered when considering ultimate mining pits optimized over various subsets of stochastic realizations. Accounting for scenario-level uncertainty allows mine plans to be assessed against several probabilistic subsurface interpretations. Scenario-level uncertainty is found through clustering stochastic geostatistical realizations and optimizing final pits across the realizations in each cluster. Where these pits are geometrically different, plans for each scenario differ. Knowing these differences allows the value of each planning alternative to be assessed based on the value and relative probability of each scenario. These results also facilitate the use of formal decision-making frameworks for planning, leading to optimization that better represents the full statistical characterization of the deposit. An example utilizing this approach evaluates both infrastructure placement and drilling program requirements. In both cases, scenario-level uncertainty improves initial plans by limiting opportunity costs and identifying additional potential.