Search Documents

By D. D. Liu

This paper proposes a charge induction dust measurement method based on detrended fluctuation analysis (DFA) for use in coal mine environments, based upon electrostatic interference, dust properties, wind speed, particle size, moisture content and other factors. In this methods, sequence x(t) is first obtained through a dust concentration sensing probe, and then the cumulative deviation y(t) is calculated, and y(t) is divided into same lengths. Secondly, a first-order linear fit is used for data of each interval, and mean-square deviation filtered DFA was calculated for each interval. Finally, the dust mass concentration of the corresponding time is obtain by supplemented calibration coefficient and fitted the data point which is the mean and square root for all lengths of interval. Simulation and verification experiments showed that the charge induction dust measurement method based on DFA can reduce coal mine electrostatic interference effects with high accuracy. The design has been successfully applied to select areas.

Aug 1, 2013

The goal of this presentation is to firstly, review mine effluent permits in a number of regulatory jurisdictions; and secondly, to develop a strategy for incorporating the regulatory requirements into the environmental assessment (EA) process for new mine proposals. The focus was on the province of British Columbia (BC) and their recent initiative on the One Project, One Process initiative. This task was approached by reviewing mine effluent permits for various regulatory jurisdictions and comparing them to BC mine effluent permits. This comparison revealed a variety of approaches for designing mine effluent permits, but there is a common scientific approach, which supports the conclusion that the permitting of mine site discharges can be designed based on a scientific approach. This approach is expected to: (a) achieve sound environmental protection, (b) demonstrate the application of Best Achievable Technology, (c) incorporate sound sustainability approaches, (d) incorporate regulatory objectives, and (e) create efficiencies for the regulator and mining industry. There is an essential precursor to developing a sciencebased effluent permit for which the proponent must provide: (1) the necessary technical assessment information to demonstrate the mine effluent permit application will result in an environmentally protective effluent discharge, to the satisfaction of the permitting agency; (2) the necessary level of detail for essential mitigation pollution control works to demonstrate how they will be operated to achieve the necessary treatment goals; (3) the necessary level of detail for non-treatment mitigation (passive treatment, or passive pollution control); and (4) the necessary level of detail to demonstrate how pollutants will be prevented from being mobilized (or being generated) from ore and waste materials, or, if the pollutant originates from an added milling reagent, how the reagent will be reduced. While (active) mitigation pollution control equipment is more definable in an effluent permit, non-treatment mitigation is more nebulous in terms of defining in a mine effluent permit; it is therefore recommended that appropriate management plans be developed for essential mitigation pollution control and non-treatment mitigation (passive treatment) and submitted with the proponent?s EA/effluent permit application packages. Major deficits in adequate active and passive pollution control will inevitably lead to regulatory impediments to developing a permit and allowing a mine to be developed, although EA processes strive to preclude major permit information gaps; the onus is on the proponent to provide complete information in this area. Hence the importance of EA processes ensuring that the major technical information requirements for effluent permit development are included in the EA phase. Recently, this aspect of the mine EA process has taken on a new role under the political efforts of One Project, One Review Process (Canadian) and One Project, One Process (in BC). These initiatives translate, in part, to ?synchronous permitting? (in BC): effluent permitting, for example, may be initiated shortly after the proponent submits the EA application to Ministry of Environment.

Aug 1, 2013

By Marketa D. Evans

The mining industry has a significant opportunity to capitalize on its past learnings in order to build better social relationships. The industry?s relationship with society is both critical and under pressure. Rising levels of public opposition and social conflict are already having material impacts on operations around the world. Industry has an opportunity to shape the future direction of this social engagement, build public trust and proactively respond to a material risk to operations, but first it needs to better understand the nature of the challenges and the urgency of addressing them.

Aug 1, 2013

By A. Carbonari

In order to gain competitiveness and compete at a global level, construction companies should improve their efficiency. The problem is even more relevant in the construction field, whose work processes find it hard to evolve towards new automated methods and techniques in the management field. For that reason, this paper suggests how construction companies could apply new technologies to implement automated management of environmental hazards. Based on a survey regarding the environmental risks presently experienced in construction sites, noise and dust were considered two of the main hazards. So in this paper a networked system for real time remote monitoring of the spatial distribution of dust in construction sites was developed. Such a system would relieve builders from the commitment of on-site surveys, allowing for a continuous monitoring of the site conditions and of the real exposure of each worker and pass-by to the pollutants generated by construction works. The main system requirements considered are: easy to deploy, reliable, as accurate as needed to be able to send real-time warnings and store a good estimation of the real exposure to which involved people have been subject to. So far the research produced a prototypical hardware for dust monitoring made up of wireless sensors which can be easily deployed on site. The sensors were calibrated by means of laboratory tests, where their measurements were compared with those collected by means of highly accurate instruments, which were taken as a reference. Thanks to these experiments, calibration curves for the sensors were worked out, showing also the measurement range of the sensors.

Aug 1, 2013

By H. H. Wang

Construction safety documents regulate significant safety actions and requirements by which construction workers or employees should abide in order to secure them from occupational hazard events. Therefore, facilitating faster identification of applicable safety requirements from the documents has become an important topic in the construction safety domain. To address the need in this regard, tools and techniques have been developed and research efforts have been made. One of the research efforts is to utilize ontology, a knowledge representation and reasoning approach, as the methodology to achieve the goal of identifying applicable safety requirements. In such ontology-based researches, the development and construction of the safety concept ontology is an essential task as the concepts and the relationships between the concepts both representing key safety knowledge need to be carefully identified. In this paper, the author focuses on the safety documents without predefined concept structure and aims to address the concept and relationship identification difficulties. Specifically, the author leverages the Formal Concept Analysis (FCA) methodology, a theory of data analysis that identifies conceptual structures among data sets, to mine and analyze the documents in order to discover safety concept structure and to further assist the development of the concept ontology for the construction safety documents. The author expects the application of FCA to construction safety domain can eventually benefit the ontology-based approaches for identification of applicable safety requirements.

Aug 1, 2013

By Adam Jordens

Along with gravity separation and froth flotation, magnetic separation is one of the most common techniques for separating minerals. Minerals are separated by a magnetic force that is dependent on a combination of the applied magnetic field, the magnetic field gradient and the magnetic properties of the minerals themselves. Minerals may be classified as diamagnetic, paramagnetic or ferromagnetic based on the way they interact in a magnetic field. The magnetic susceptibility of a material may be determined by using a vibrating sample magnetometer to determine the magnetic moment of the material in an applied magnetic field and then converting this measured moment into the material?s magnetic susceptibility. In the case of rare earth minerals, magnetic separation is commonly used to remove ferromagnetic iron-bearing gangue minerals and to concentrate paramagnetic valuable minerals such as monazite and xenotime. These magnetic separation steps are frequently preceded by a gravity separation step as many iron oxides and rare earth minerals have specific gravities that are much larger than those of typical gangue minerals. By varying the magnetic field intensity it may be possible to use magnetic separation to selectively separate the paramagnetic and ferromagnetic minerals that report to the concentrate after gravity separation. Test work on a Canadian rare earth ore has shown that a gravity concentration step using a Knelson concentrator was able to selectively concentrate heavy magnetic minerals as evidenced by increased recoveries, relative to the Knelson tailings and fresh feed, after processing through a wet variable intensity magnetic separator. Mass pull to the Knelson concentrate was 4.5 % and the magnetic recovery of this concentrate, at 0.94 T, was approximately 40 % higher than the magnetic recovery from the Knelson tailings (70 % versus 30 %). The products of the wet high intensity magnetic separation were also analysed using a vibrating sample magnetometer to determine the magnetic susceptibilities of the various concentrate and tailings products.

Aug 1, 2013

By Patrick Cloutier

Presentation objectives ? Introduce discrete-event 3D computer simulation as a tool to design, improve and optimize construction projects: ? Describe a real typical construction project planning issue. ? Present an applied use of simulation to solve this issue. ? Detail benefits of using simulation versus traditional planning methods.

Aug 1, 2013

Some examples of the results of research projects, conducted in the KOMAG Institute of Mining Technology are presented. Special attention is paid to mining machines and equipment, and improving work safety and comfort of miners in underground workings. From numerous scientific and technical achievements of the KOMAG Institute within the last 2 years, a few design solutions have been selected for a presentation. Some results of European projects on innovative solutions are described as well, highlighting KOMAG?s role in the national and international research area.

Aug 1, 2013

By K. A. Mackinnon

The choice of fan type (axial flow, centrifugal or mixed flow) most suited for a mine ventilation application depends on a number of technical and economic factors. For each project, the relative importance of these factors will vary. It is worthwhile to carry out an assessment on a case by case basis. The paper, by discussing a number of technical and economic factors and their interactions, will provide the ventilation official a methodology to easily and methodically undertake such an assessment.

Aug 1, 2013

By J. G. Bennett

Coal consumption has increased globally by 57% over the last ten years. Underground mining typically provides coal of the highest calorific value and accounts for the greatest proportion of production. Despite a negative environmental image and indeed impact, this industry appears likely to thrive on the global scale for many years to come. Such mining consumes large amounts of electricity with implications for carbon dioxide emission at power plants and emits substantial quantities of the powerful greenhouse gas methane. In response to this significant carbon footprint, the European Union has funded research to examine the potential for a range of improvement technologies in a project entitled Low Carbon Mine Site Energy Initiatives (LOWCARB). Coal properties related to seams and mines, together with longwall characteristics, provide the basis for research into modelling optimally efficient methane drainage with a view to assisting mining as well as maximising electricity generation at surface and hence oxidation of the methane. Possible systems for the oxidation of very low concentration methane in ventilation air, which contributes the greatest greenhouse gas impact due to the volumes emitted, have been studied and modelled. Simulation and investigation of intelligent optimisation of electricity demand patterns provide the basis for reducing the demand peaks at mines and hence the cost and ultimately the carbon footprint of a mine, while specific investigations have been undertaken into ventilation efficiency at an unusually challenging mine and simulation of mine water pumping in order to develop an innovative method to monitor pumping systems efficiency. For post-mining use, the potential of disused shafts for compressed air energy storage to improve the operation of future electricity grids with high renewable energy penetration by reducing peak generation capacity requirements has been studied. While underground coal mining will always by definition be related to a significant carbon footprint, this paper provides an overview of a set of initiatives that can make a positive environmental impact while controlling costs across a huge global industry.

Aug 1, 2013

By Nicholas C. Williams

This paper presents the development of a demand reduction and responsive strategy capable of reducing the electrical power demand, particularly during peak conditions. The work presented includes a case study of a UK colliery. Areas explained are the equipment installation at the mine; the development of the demand reduction strategy including the load profile database and prediction optimisation model. Some live production data from the power meter installation at the mine is also presented.

Aug 1, 2013

By Mousa Mohammadi

Due to operational advantage of dragline in simultaneous excavation and back-filling, the equipment has gained vast importance in open-pit mining. Besides, absence of auxiliary haulage units and a myriad of other benefits are also credited in favor of excavation of muck piles by the draglines. However, the aspects of production, productivity and economics are of utmost significance in dragline operation and planning. In this light, the present paper is an endeavor to analyze availability and utilization of dragline operations. The paper presents a good amount of data for 4-draglines operating in one of the major opencast projects in India. The study reveals the trends of availability and utilization of these draglines during last 11-years. Furthermore, the study also highlights the salient reasons for loss of available hours and for idling of the draglines. Some startling information and facts have been illustrated in form of graphs and pie charts.

Aug 1, 2013

By I. A. Kovalevska

Considered problems: elaboration and implementation of resource-saving technologies, low-cost support systems improvement, openings security and support, based on wallrock condition control with supreme implication into the rock pressure occurrence counteraction work. Results of analytic and underground investigations using computer simulation of the finite elements in order to calculate stressstrain state of the multivariable geomechanical systems are presented. Solutions of concrete objectives are found using spatial geomechanical model of solid motion around openings, considering real geomechanical parameters formation of support forms with proper conditions of their contact and real mechanical characteristics. Ultimate solutions of resource-saving technologies implementation based on the analysis of multivariate vertical, horizontal, and reduced stresses components calculation and also near-contour rock, support bearing components and security constructions movements are found. Results of experimental investigations of combined supports and security constructions, which increase openings' stability in difficult conditions of flat coal seams are presented.

Aug 1, 2013

By M. Verri

The paper describes the design options available for the simultaneous production of liquid sulphur dioxide, via cryogenic condensation, and sulphuric acid in a sulphur-burning sulphuric acid plant. The impact of the operating conditions of the cryogenic condensation on plant capital and operating costs are discussed, with the main focus on the optimization of the most important economic and operative drivers of the non-ferrous mining industry, such as energy efficiency, reliability, and availability. A case history relevant to an integrated sulphurburning plant producing liquid sulphur dioxide and sulphuric acid, recently started up in the Democratic Republic of Congo, is described. Keywords sulphur burning, sulphuric acid, liquid SO2, cryogenic SO2 condensation, liquid sulphur dioxide, sulphur dioxide.

Aug 1, 2013

By R. Argane

In this work we assessed the geochemical behavior of concentrator tailings deposited at the abandoned mines of Zeida and Mibladen (Upper Moulouya, Morocco), using physico-chemical analyses, mineralogical characterization, acid base accounting and weathering cell tests. The aim of the study was to evaluate mine drainage quality and to assess metal mobility from these concentrator tailings. Chemical analyses show that the Upper-Moulouya abandoned tailings contain relatively high quantities of lead (0.261 to 0.594 % wt). Mineralogical analyses reveal the abundance of neutralizing minerals (calcite, dolomite, ankerite, and aluminosilicates) which influence mine drainage and metal mobility in mine tailings. Leachate analyses from weathering cell tests show alkaline conditions, small conductivity values, and low solubility of Pb-mineral phases. According to these results, abandoned mine tailings in the Upper-Moulouya district have very low potential for generation of contaminated mine drainage and for leaching of heavy metals. However, the inhalation of tailings exposed to winds generate dust problem facing the local population and may cause health consequences.

Aug 1, 2013

By J. Kalejta

Ever increasing depth of mineral extraction presents a challenging environment for hard rock underground mines. High in-situ stresses and associated seismicity with potential rockburst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. This paper describes a method of mechanized installation of a chain-link mesh evaluated at the Kiruna mine in Sweden and South Deep Mine in South Africa. A purpose-built mechanized roll mesh handler was used in this evaluation. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilizing the hydraulic circuit normally used for the feed arrangement. A number of key performance indicators have been identified as success criteria: ??A 30-50% faster installation compared to the conventional methodology ??The mesh should sustain any blast damage when applied to the blasting face ??No unraveling of the mesh when cut ??No failure of mesh under normal conditions Although the energy-absorbing mesh combined with yielding rock bolts is a ground support system of choice for rockburst prone conditions, the operational upsides recognized during the evaluation imply that this product can also be competitively used in less demanding ground conditions where customarily weld mesh or shotcrete are used as a primary surface support. The main conclusion: a fast, safe and fully mechanized installation.

Aug 1, 2013

By H. Nejati

Experimentally, the Semi-Circular Bending Moment (SCB) fracture toughness test results of Basalt Specimens Under Illumination (BSUI) have shown reduction in fracture toughness and failure force as a result of micro-cracking. The fractographic investigation of BSUI confirms initiation and extension of micro-cracks. Determination of a relation between strength reduction (herein fracture toughness reduction) and density, location and orientation of thermo-mechanical induced cracks due to microwave radiation is critically important. Numerical modeling can bridge strength reduction and the density of thermal microcracks generated due to microwave radiation. Discrete Element Modeling (DEM) is a power tool for simulation of micro-crack initiation, coalescence into macroscopic fractures and failure mechanisms in brittle rock specimens under different stress regimes (herein combination of pure tensile stress due to SCB testing, and thermal stress due to microwave radiation). For this purpose, a DEM modeling of SCB testing of basalt using EDEM (i.e., a DEM based software). DEM models are calibrated according to results of experimental SCB testing as reported in previous papers. This paper first reviews some background data on SCB fracture toughness, and experimental results of fracture toughness of microwave treated SCBs. Then it proposes a new methodology for simulation and validation of rock samples exposed to microwave illumination with regard to experimental results, and discusses the correlation between fracture toughness of BSUIs and density of micro-cracks, which is attributed to applied microwave power and duration of illumination.

Aug 1, 2013

Leadership "Organizing a group of people to achieve a common goal" Paradigms ? Rush to produce or cut costs. ? The most important thing after safety is production. ? We?ll take care of ??this?? once in production. ? I know what to do, 30 years of experience in mining. ? I want a 100% reliable operation.

Aug 1, 2013

By Julian V. Simela

Conventional methods of underground surveying use theodolites/total stations and 3D laser scanners to obtain information about the underground environment. Current methods of geo-referencing these instruments to a mine reference system include triangulation, trilateration and resection. However, despite technological advancements, surveying procedures have remained slow, laborious and relatively unchanged during the last half-century. Recent innovations in the robotics community have shown that automated mapping of underground mining tunnels can be undertaken using 2D/3D laser scanners. These techniques have the potential to, in turn, improve upon current underground surveying and mapping methods. Automating surveying and mapping using current surveying tools without changing the setting up procedures or removing current constraints, or even changing the type of equipment used, does not change the status quo. The problem of moving from a static, tripod based surveying and mapping system to an unconstrained mobile surveying and mapping system is the subject of this paper. A current challenge for automated mapping is the ability to automatically geo-reference a mobile mapping system to a mine reference system. For a mobile mapping system that uses a horizontally mounted 2D laser scanner to gather data of the underground environment, the challenge of determining its position and orientation within the mine environment is magnified even more. This paper introduces Mobile Automated Scanner Triangulateration (MAST), a technique under development at Queen?s that is designed to geo-reference a mobile mapping system to a mine reference system for the purposes of underground mine surveying. MAST quickly and automatically determines scanner 2D position and orientation (azimuth) in a mine reference frame by using minimal human input.

Aug 1, 2013

By S. Beitler

The availability of renewable energy does not meet the demands of consumption. Hence, fossil fuels will continue to be an important energy source, and coal promises to cover the requirements for the coming decades. Because of its high energy content, deep lying bituminous coal and anthracite are important for energy generation. One trend in the future of coal mining is thin seam mining, because thick seams more and more have been exploited. A well-known and approved longwall mining method for thin seams is plowing which has big advantages compared to a shearer because of its compact design. The extraction of those thinner coal seams will become more and more important in coal industry and therefore the plow will receive more attention in future. Most approaches in longwall automation are focused on the shearer and need a more or less intelligent exploitation machine. Therefore those approaches cannot be used for the plow technology. The authors introduce a shield-data-based horizon control (SDHC). The developed approach integrates the shield data provided by the roof support and process monitoring into the horizon control process to keep the plow in seam even if the seam trend changes. This control concept can be used for the shearer as well as for the plow. The basic idea of SDHC for plow application will be introduced in this paper and first simulation results will be shown.

Aug 1, 2013