Search Documents

By J. Drzymala

Particle beneficiation tests are often conducted to determine how the recovery of a key component of a particle mixture varies with overall product yield, i.e., the separation curve. The results can be misleading when an attempt is made to determine the effect of feed grade by comparing separation curves representing different feed grades or key component concentrations. This is a shortcoming of the conventional recovery versus yield diagram, which may not appear to be affected by feed concentration. To overcome this shortcoming, a method is presented for transforming and normalizing the recovery and yield coordinates so that the separation curves representing dif-ferent feed concentrations are directly comparable.

Jan 1, 2007

By Charles H. Minott, Michael J. Markow, Robert D. Wyatt, Fred Moavenzadeh

The substantial investment in tunnels anticipated in the next twenty years has focused new attention on the economics of tunnel construction itself and on some costly problems associated with underground work: the uncertain geologic conditions, the performance and adaptability of men and equipment, and the need for quicker, more efficient excavation methods. There also exists a need to develop better ways of estimating tunnel construction. Inaccuracies in current bid estimates stem from a number of causes, among them (1) the effects of geologic conditions, which are not adequately known prior to construction, (2) the dependence of actual cost on the construction method used and on the interactions among the operations occurring underground, and (3) the reliability of tunneling equipment. Inability to estimate final costs for conventional tunneling more accurately has in turn caused difficulty in gauging the costs and benefits attributable to new tunneling technologies either under development or for which R&D programs are planned. ATTRIBUTES OF THE TUNNEL COST MODEL This paper presents a computer based Tunnel Cost Model (TCM) which quantitatively assesses the uncertainties inherent in underground work, and is detailed enough to aid in preparing estimates or bids. The model employs appropriate techniques of subjective (or "degree of belief") probability and computer simulation of tunnel construction operations to estimate distributions of total tunnel

Jan 1, 1974

The Subtropolis mine is a room-and-pillar mine extracting the Vanport Limestone near Petersburg, Ohio. In February 2018, mine management began implementing a heading reorientation to better control the negative effects of excessive levels of horizontal stress. The conditions in the headings improved, but as expected, stressrelated damage concentrated within crosscuts. The mine operator has worked to lessen the impact of the instabilities in the outby crosscuts by implementing several engineering controls. With the implementation of each control, conditions were monitored and analyzed using observational and measurement techniques including three-dimensional (3-D) LiDAR surveys.

Jan 7, 2020

Caterpillar’s 797 327-t (360-st) mining truck is currently being tested at the company’s proving facilities. Mine evaluations began in the second quarter. The unit will be commerically available in North America in 2000 and worldwide in 2001. The new model is the largest of Caterpillar’s off high-way truck line. In addition, the company has replaced its 966F series II and 970 F wheel loaders with the966G and 972G models. 797 mining haul truck Caterpillar developed the 797 mining haul truck in response to mining companies seeking to reduce cost per ton in large-scale operations. The 797 is sized to work with loading shovels used in large mining operations. And Caterpillar will match the body design to the material being hauled, to optimize pay-loads.

Jan 1, 1999

By A. Moergeli

The Swiss are currently building the world’s longest tunnel, the 35-mile long Gotthard Base Tunnel. At Sedrun, for the first time in tunneling, four Roadway Support Machines will drive through most difficult ground, supporting variable diameters of up to 13 m. The machines are prepared for their first deployment. At Amsteg, two Hard Rock TBMs have successfully crossed a known fault zone by applying full circle steel arches and shotcrete immediately behind the cutter head. Comparisons between Drill& Blast and Hard Rock TBM are shown.

Jan 1, 2005

By A. Mahmoudkhani

There has been a continuous interest in chemical aids for processing Canadian oil sands by hot water extraction process since the first commercial industry operation in 1967. Several inorganic and organic chemical systems have been introduced, of which sodium hydroxide is the most widely used extraction process aid by major producers. Use of NaOH, however, results in accumulation of sodium ions in recycled water, causing higher clays dispersion and producing tailings with poor geotechnical properties that turn into mature fine tailings. This is especially true for low grade and oxidized ores, which present the greatest challenges in bitumen recovery and produce the major portion of fine tailings. In this paper, we are presenting a novel method based on use of inorganic polymers as process aids for various low grade oil sands ores. Denver flotation cell and a laboratory scale hydrotransport loop were utilized to evaluate the effect of chemical dosage and operating parameters on the processability of oil sands samples from Athabasca region. Process tailings were examined for properties such as water chemistry, suspended solids, settling rate and the ease of tailing treatments. Our results demonstrate that the use of inorganic polymers during the froth process lead to a significant improvement in bitumen recovery from low grade oil sands and can improve further tailing treatments. This offers a viable solution that can be easily incorporated into current processing facilities and deliver several operational and economical benefits. Advantages in use of inorganic polymers versus sodium hydroxide are presented in details.

Jan 1, 2012

By H. Ipek

Industrial grinding machines used in the mineral processing industries are mostly of the tumbling mill type. These mills exist in various types: ball, rod, pebble, autogenous, and semi-autogenous. Balls and rods are traditionally media shapes used in the tumbling mills. In resent years, as an alternative to balls, grinding charges with various shapes are being used. Cylpebs are slightly tapered cylindrical grinding charges with length equaling diameter, and all the edges being radiused. Cylpebs of equal diameter and length have 50% greater surface area and 45% greater weight than balls of the same material. In addition, they have 9% higher bulk density than steel balls, or 12% higher bulk density than cast balls. An important advantage of cylpebs over balls is that cylpebs produce narrower granulometric distribution due to their shapes. However, some discrepancies were found in the literature regarding the milling performance of cylpebs in comparison with balls (Chi, 2004). In recent studies, Chi (2004) has provided detailed information on cylpebs and has compared these to balls in relation to media mass, size distribution, surface area, and input specific energy. Ipek (2006) has investigated the effects of cylpebs and balls with equal mass and surface area on the breakage rate of quartz, using cylpebs and balls separately. Similarly, Lameck and Moys (2006) have investigated the effects of balls and worn balls on breakage rate of material using worn balls as grinding environment. However, no study has attempted to investigate the effects of grinding environment other than balls on the brekage distribution. As indicated by Prasher (1987), the breakage distribution function is independent of the following variables in ball mills: hold-up (Mika et al., 1967; Kelsall et al. 1969), mill speed and ball load (Herbst and Fuerstenau, 1972), media load and ball density (Kelsall et al., 1973), mill diameter (Malghan and Fuerstenau, 1976), and powder charge (Shoji et al. 1980). The aim of the present paper is to compare the effects of cylpebs and balls on the breakage distribution function of quartz with respect to same mass and same surface area. BACKGROUND Comminution as a rate process is called kinetic approach. Studies on the kinetic approach are reviewed by Oner (2001). Oner states that grinding kinetics are based on studies by Kolmogorov in 1941 and that Robert (1950) is the first to suggest this approach. Later, Melzak, Loeveday, and Reid have improved the grinding kinetics equation; and, Austin and Lynch have conducted two basic studies on the analytical solutions of these equations. Considering the results of studies comparing the size reduction mechanisms, it has been accepted that breakage constitutes of two operations. These two basic operations, first defined by Epstein (1948), are those of selection of material for breakage and the distribution of breakage material to particle sizes smaller than the initial size (Lynch, 1977). Epstein defined the two operations as: ? Pn(y), the probability of breakage of a particle size in the nth step of the breakage process. ? F(x,y), the cumulative distributions by weight of particles of size x<y arising from the breakage of a unit mass of a size y. Probability of breakage is called a selection or a breakage-rate function (Si). Characteristics size distribution after breakage is called a breakage distribution or appearance function (Bi,j). Due to the difficulties in representing particle size distributions mathematically and constantly, the batch equation based on particle size fraction is suggested. Thus, as is the case in breakage distribution and specific rate of breakage, the breakage parameters were defined by batch grinding experiments conducted in laboratories (Oner, 2001). When effective breakage occurs in the mill, the breakage of material with single feed size fraction usually fits first order grinding kinetics and the specific rate of breakage values can be calculated through the slope of semi-log plot. The values of the breakage distributions are deduced from the size distributions at short grinding times where there is mainly size 1 material breaking and only small amount of smaller sizes to rebreak (Austin et. al., 1984). B values can be calculated by using BII. [ ] where j is the top size of the charge, Pi(t) is the cumulative percent undersize of i th size interval at the short grinding time which gives no more than about 30% broken out of the top size interval. Cumulative primary breakage distribution, Bi,j, is also defined in an empirical form by [ ] where xi is the top size and Bi,j is the weight fraction of primary breakage products. The parameters F, ? and ß define the size distribution of the material being ground. On plotting size versus Bi,j on log scale, the slope of the lower portion of the curve gives the value of ?, the slope of the upper portion of the curve gives the value of ß, and F is the intercept as in Fig.1. [ ]

Jan 1, 2009

By Christopher J. Bise

INTRODUCTION A mine&apos;s power system represents the driving force behind all of the extraction and auxiliary operations, because the production and transportation of mined material and the operation of equipment, such as fans and pumps, are all dependent upon a power source. Once, compressed air was the primary power source in mining; today, however, electrical power dominates. This chapter reviews the basic theories of com- pressed-air and electrical power and provides several examples of applications in mine power systems. COMPRESSED-AIR POWER General Compressed air has been, and should continue to be, an important source of power in mining operations. It has been used as a means of blasting coal in conventional mining and is widely used to operate stopers, mucking machines, and other air tools in both coal and hard-rock mines. Such applications demonstrate the suitability of compressed air for applications requiring linear motion, but it is also utilized for its reliability and safety. A compressed-air system is composed of a compressor, a receiver, a distribution network, and the air-operated machines. A compressor takes in air at normal atmospheric pressure (free air) and compresses it to a higher discharge pressure. The discharge pressure must be high enough to overcome the friction in the distribution system of pipes and hoses and deliver the compressed air to the machines at the pressure recommended by the manufacturer. The most common type of compressor used in mines is the reciprocating compressor in which the air is compressed by a piston in a cylinder. An air receiver is a container or storage tank that is located in the distribution system between the compressor and the machines. It stores compressed air, when the full capacity of the compressor is not being used, and gives a more steady flow of air to the machines. The distribution network consists of pipes, Oalves, elbows, tees, and hoses that transmit the compressed air from the receiver to the machines in the mine. It is essential that the distribution system be designed with the proper sizes and lengths of pipe, hose, and other components to keep pressure losses well within allowable limits. The air-operated machines consist primarily of drifters, stopers, pluggers (sinkers), slushers, and several other pieces of equipment. Compressor Operation Every compressor is made up of one or more basic elements; a single element, or a group of elements in parallel, comprises a single-stage compressor. Many compression problems involve conditions beyond the practical capability of a single compression stage. Too great a compression ratio (absolute discharge pressure divided by absolute intake pressure) may cause excessive discharge temperatures or other design problems. It, therefore, may become necessary to combine elements or groups of elements in series to form a multi- stage unit, in which there will be two or more steps of compression. The number of stages commonly used in reciprocating compressors is as follows: Pressure Number of stages 0- 150 pig 1 80- 500 psig 2 500-2500 psig 3 2500-5000 psig 4 When pressure is referred to as pounds per square inch gage (psig), it means the pressure (in pounds per square inch) above barometric pressure as measured by a gage. The sum of barometric pressure and gage pressure is the absolute pressure (in pounds per square inch). The gas is frequently cooled between stages to reduce the temperature and volume entering the subsequent stages, thereby reducing the work required for compression. The basic reciprocating compression element is a single cylinder compressing on only one side of the piston (single-acting). A unit compressing on both sides of the piston (double-acting) consists of two basic single-acting elements operating in parallel in one casing. The reciprocating compressor uses automatic spring-loaded valves that open only when the proper differential pressure exists across the valves. Intake valves open when the pressure in the cylinder is slightly below the intake pressure. Discharge valves open when the pressure in the cylinder is slightly above the discharge pressure. In Fig. 1, Diagram A shows the basic element with the cylinder filled with air at atmospheric pressure. On the corresponding theoretical pressure-volume

Jan 1, 1986

By Jacques F. Abrahamse, Kevin A. Bahe, T. Arthur Palm, Gregory E. McCluskey, Stephen L. Bessinger

Introduction Basis For System San Juan Coal Company (SJCC) is a subsidiary of BHP Billiton. Until recently, BHP Billiton operated three surface mines in northwestern New Mexico: Navajo, San Juan, and La Plata. The San Juan and La Plata Mines supplied the San Juan Generating Station operated by Public Service of New Mexico. Stripping ratios at those operations were increasing, and by 2000 a feasibility study was underway to develop SJCC’s vast underground reserves as a replacement. Early in the evaluation and planning phase for the San Juan Underground Mine, it was determined that the target seams (Fruitland #8 and #9) had a high propensity for spontaneous combustion. Spontaneous combustion was identified as a risk, both to personnel and equipment, and to the ability of SJCC to reliably fulfill its obligation to the power plant. In the last 20 years, several western US coal mines suffered underground spontaneous combustion events and/or mine fires. Included in this group were Colorado Westmoreland’s Orchard Valley Mine (1987), RAG’s Willow Creek Mine (1998 and 2000), Oxbow’s Sanborn Creek Mine (1999), the West Elk Mine of Arch Coal (2000), Arch’s Skyline Mine (2002), Western Fuels’ Deserado Mine (1996), and the West Ridge Mine of Andalex Resources (2003). The cause for the majority of these fires was spontaneous combustion. Fighting the fires required injection of an inert gas or foam. Nitrogen and carbon dioxide were the predominant choices of inert gas. In all cases, the gasses had to be trucked in from considerable distances. Before the inert gas could be used, injection holes had to be drilled into or near the suspected fire locations. This drilling and trucking caused costly delays in the timing of the fire fighting effort, and was not as precise as desirable. Emergency purchasing of gas and pumping services was extremely expensive, running as high as $70,000 per day at one mine. As a result of the experience of other western US coal operators, and the risk inherent with spontaneous combustion at SJCC, it was decided to pursue installation of a nitrogen delivery facility on-site at SJCC. This decision was later expanded to include a continuous supply of nitrogen.

Jan 1, 2005

By L. L. Chasko, D. W. Alexander

Researchers from the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research conducted an assessment of the effects that ground control mesh might have on rock and float coal dust distribution in a coal mine. The increased use of mesh to control roof and rib spall introduces additional elevated surfaces on which rock or coal dust can collect. It is possible to increase the potential for dust explosion propagation if any float coal dust is not adequately inerted. In addition, the mesh may interfere with the collection of representative dust samples when using the pan-and-brush sampling method developed by the U.S. Bureau of Mines and used by the Mine Safety and Health Administration for band sampling. This study estimates the additional coal or rock dust that could accumulate on mesh and develops a means to collect representative dust samples from meshed entries.

Jan 1, 2014

Many states rely upon the Pennsylvania 1957 “Gas Well Pillar Study” to evaluate the coal barrier surrounding gas wells (Commonwealth of Pennsylvania, 1957). The study included 77 gas well failure cases that occurred in the Pittsburgh and Freeport coal seams over a 25-year span. At the time, coal was mined using the room-and-pillar mining method with full or partial pillar recovery, and square or rectangle pillars surrounding the gas wells were left to protect the wells. The study provided guidelines for pillar sizes under different overburden depths up to 700 ft. The 1957 study has also been used to determine gas well pillar sizes in longwall mines since longwall mining began in the 1970s. The original study was developed for room-and-pillar mining and could be applied to gas wells in longwall chain pillars under shallow cover. However, under deep cover, severe deformations in gas wells have occurred in longwall chain pillars. Presently, with a better understanding of coal pillar mechanics, new insight into subsidence movements induced by retreat mining, and advances in numerical modeling, it has become both critically important and feasible to evaluate the adequacy of the 1957 study for longwall gas well pillars. In this paper, the data from the 1957 study is analyzed from a new perspective by considering various factors, including overburden depth, failure location, failure time, pillar safety factor (SF), and floor pressure. The pillar SF and floor pressure are calculated by considering abutment pressure induced by full pillar recovery. A statistical analysis is performed to find correlations between various factors and helps identify the most significant factors for the stability of gas wells influenced by retreat mining. Through analyzing the data from the 1957 study, the guidelines for gas well pillars in the 1957 study are evaluated for their adequacy for room-and-pillar mining and their applicability to longwall mining. Numerical modeling is used to model the stability of gas wells by quantifying the mining-induced stresses in gas well casings. Results of this study indicate that the guidelines in the 1957 study may be appropriate for pillars protecting conventional gas wells in both room-and-pillar mining and longwall mining under overburden depths up to 700 ft but may not be sufficient for protective pillars under deep cover. The current evaluation of the 1957 study provides not only insights about potential gas well failures caused by retreat mining but also implications for what critical considerations should be considered to protect gas wells in longwall mining.

Jul 28, 2020

By D. L. Petersen, C. R. Nelson, B. K. Nelson, B. D. Wagener

The Lafayette Bluff tunnel, currently under construction for the Minnesota Department of Transportation (MnDOT), will be among the widest highway tunnels in the United States. The 199-meter tunnel is being constructed in a closely jointed, variably weathered diabase rock mass. Cover above the tunnel crown ranges from 4 meters to 27 meters, and is less than the tunnel excavated width of 18.3 meters for about 60 percent of its length. These factors dictated special support and lining design, limitations on excavation sizes and required sequences for support installation. Tunnel excavation is by controlled blasting, with multiple top headings and bench. Rock support and lining consists of external portal beams, rockbolts and reinforced shotcrete. A final concrete lining provides structural support for the rock mass and the membrane waterproofing system.

Jan 1, 1991

By A. Jarosz

The surface manifestation of underground mining usually entails five distinct types of surface movements, which can affect or damage surface structures, facilities and renewable resources. These movements developing at the surface can be described by (Bell, 1975; Bhattacharya and Singh, 1984): - vertical displacement, i.e. subsidence, - horizontal displacements, - slope or tilt, i.e. the derivative of the vertical displacement with respect to the horizontal distance, - curvature, i.e. the second derivative of the vertical displacement with respect to the horizontal distance, and, - horizontal strain, i.e. the derivative of the horizontal displacement with respect to the horizontal distance.

Jan 1, 1986

By F. Habashi

The phosphate fertilizer industry is at present based mainly on the use of sulfuric acid. This technology results in the generation of large amounts of radioactive gypsum that represents disposal and environmental problems. Also it involves the use of expensive reactors for acidification that necessitates the frequent replacing the damaged agitators. Applying hydrometallurgical techniques such as in-situ, heap, or vat leaching to phosphate processing could solve these problems. In this case, however, nitric acid must be used and dicalcium phosphate (40% P2O5) may be obtained as a final product. It is insoluble in water but soluble in citric acid and is an excellent fertilizer. This technology does not interfere with uranium recovery if desired. In addition it permits the recovery of rare earths which are otherwise lost in the gypsum.

Jan 1, 2011

By Steve Kral

Invensys is a London-based supplier of automation and control systems to a variety of manufacturing and processing industries. Through its global subsidiaries, Invensys provides customized, advanced process control systems and networks for automating industrial plants, including mineral processing plants. The company employs more than 80,000 people worldwide in its four divisions. They include Automation, Control, Powerware and Software Systems. These four divisions work together to design the complete package for their customer’s automation and process-control needs.

Jan 1, 2002

By Stone. Jon P.

INTRODUCTION Countries that are currently developing their mineral potential have unique information systems requirements to support these activities. The mining laws usually grant the State considerable authority over the process. In many instances, the mining laws give a government agency the responsibility for granting and controlling exploration permits and development concessions. This is the case in Costa Rica. The Direcion of Geologia, Minas, y Hidrocarburos (DGMH) of the Ministerio de Industria, Energia y Minas (MIEM) is responsible for the management and operation of the National Mining Register. This paper describes the results of two studies of the information system requirements to support the National Mining Registry as well as those supporting some of the other function of the DGMH. The first of the studies reviewed the situation before the installation of computer equipment. The second study evaluated the installed systems. BACKGROUND Historical Perspective Mining in Costa Rica is at present a relatively minor part of the economy. It consists primarily of industrial minerals and gold production. Gold production is largely by small-scale miners and may be more substantial than reported. There is considerable interest on the part of the Government in both having a better understanding of the existing mining industry and promoting future development. Mining law was first provided by the Ordinanza de Mineral (of 1830). This was replaced by the first Mining Code of 1953. Apparently, one of the first problems caused by the 1953 law was the granting of concessions which were not worked. A 1968 agreement with ALCOA also resulted in political conflict. The Government worked on a new Mining Code for many years and in 1982 the current Mining Code was enacted. Draft implementing regulations were prepared in April 1984. Mining Code of 1982 The Mining Code of 1982 addresses most aspects of mining in Costa Rica including the declaration that all mineral resources are to be the property of the State. The State may grant exploration permits and exploitation permits. The exploitation of hydrocarbons, radioactive minerals and certain water resources was reserved to the state. The DGMH was given authority to settle placer claim disputes, maintain a registry of exploration permits, and exploitation concessions. and generally supervise mining activity. Towards this, the Mining Code of 1982 includes rather detailed requirements for the processing of application for permits and concessions. Mining Code Application Requirements The following briefly describes the requirements to give the reader a feeling for the complexity of the process. Currently, over 1,000 active applications, exploration permits and exploitation concessions are being monitored under the process. The number remains relatively consistent in that the number of new applications is usually about the same as the applications that are put aside. The time and date of the filing must be certified by the DGMH. The application must include all the information specified in the Mining Code. If incomplete, DGMH must notify the applicant of the deficiencies or omissions and direct that the applicant correct the deficiencies or omissions within 8 business days (a single 30 business-day extension is allowable). If the applicant does not respond as directed, the application is deemed as not having been filed and the pertinent information is placed in the files. The DGMH must reject the application outright and direct it be placed in the files in the following cases: (a). If the new application covers the area of a previous permit or concession, either being processed or already granted.

Jan 1, 1987

By Christopher Haycocks

The growth of computer and ground control technology in recent years, combined with an urgent demand for low-cost fossil fuels and mineral resources, has set the stage for full-scale utilization of computers in mine planning. Steeply rising production costs and the need to preserve the environment are placing great demands on engineers to improve their mining efficiencies, which can best be accomplished by applying the full capabilities of the computer. Pressure to develop and perfect programs with an immediate potential for improving mine de- sign, reducing mining costs and extending the viable coal reserves of the country has already come to bear in the form of exploding energy requirements, environ- mental considerations and the visible limitations of other energy sources. The computer program discussed in this paper, RAMPLAN (Rock Mechanics Applied to Nine Planning), was constructed as part of a continuing effort at Virginia Polytechnic Institute & State University under the sponsorship of the Office of Coal Research to develop a suite of programs to benefit the mining engineer in improving mine design and evaluation techniques. This program averages out structural data values obtained from randomly placed or gridded point sources across a mining property and uses these values in structural design equations. The basic purpose of the program is to provide accurate estimates of mineable tonnages, based on a realistic assessment of structural conditions existing in the deposit, for use in subsequent evaluation programs. Program output, however, also provides sound engineering data for the mine planner to use in planning and laying out new properties. Mining dimensions produced by the program provide a good starting point for initial layouts; and as more refined procedures are developed for increasing and improving the quality and quantity of information from boreholes, this information may be used with increasing confidence. The rock mechanics principles utilized in the program are generally well-established with full details provided to the user. To produce meaningful results extensive input data, obtained from exploration borehole core data, outcrop sampling points, or mine samples, are required. To assist the engineer, details of the types of tests that should be conducted have been listed. By including all of the ground control equations in the program the otherwise long and tedious calculations can be performed easily and quickly, and the work can provide the basis for a more detailed ground control study. The program is written in Fortran IV Level G to run on an IBM 3701155 ASP and requires 156K storage.

Jan 1, 1973

By E. Lammer

"Underground mining processes are dangerous. The design of mining equipment, which is able to cope with the hostile underground environment, is a challenge for all machine manufacturers. Presupposition for realizing the vision of SANDVIK for zero harm for working with SANDVIK equipment is the installation of the appropriate processes. Into the product engineering and product development processes of Sandvik Mining and Construction, a specific "Product Safety Process" has been integrated, where all safety related activities like identification of all life cycle hazards, risk management and safety verification / validation are planned, performed and documented. Product safety shall be „designed into" the products. Therefore, specific research activities have been started, to address the safety and health related topics for the development and for the engineering of SANDVIK mining machines."

Jan 1, 2011

By Robin B. Dill, Mark Pelletier, Daniel J. Dobbels, Subodh Bhaumik, Daniel J. VanRoosendaal

Although primarily cut-and-cover excavations are required for replacement of the existing elevated I-93 interstate highway through the heart of Boston for the Central Artery/Tunnel (CA/T) project, some mined tunnel construction was also undertaken. The mined tunneling conducted was the 22-m-wide northbound roadway structure which passed below a 20-m-deep operating underground subway station that was built in 1913. The innovative underpinning scheme used to support the subway station during construction resulted in the successful mining beneath the subway station with negligible vertical settlement. Two grouting galleries were carefully mined below the subway structure, and pre-grouting of the granulary, pervious glacial soils and weathered bedrock was carried out from these galleries. The reinforced concrete walls of the underpinning structure were constructed within three stacked drifts that were sequentially mined below each grouting gallery. After 11 cross adits were mined between the grouting galleries, cast-in-place post-tensioned girders that spanned between the stacked-drift walls were constructed to support the subway station. The stacked-drift walls also provided lateral support for the 22-m wide by 29-m long by13-m high opening beneath the girders.

Jan 1, 2001

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4 km (6.5 mi) long, 14.4 m (47.5 ft)bored tunnel that will run under the City of Niagara Falls from the Upper Niagara River to the Sir Adam Beck Power Station. The completed project will enhance the capacity of the Sir Adam Beck Power Station by adding 500 m3 (17,657 ft3) of water per second through the tunnel. The paper describes the project in which the world’s largest hard rock TBM at14.4 m (47.5 ft) in diameter is being used to excavate the tunnel. Features of the project include the use of a High Performance (HP) Main Beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area. The paper will also discuss the optimization of the TBM system as the tunnel advances through the varying geology. In June 2004 the Ontario Government announced that Ontario Power Generation(OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls—the first two tunnels were constructed in the 1950s using drill and blast techniques. The third tunnel, appropriately named The Niagara Tunnel Project (NTP), consists of a 10.4 km (6.5 mi) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG announced the selection of Strabag AG of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP Project at a price of CAN $600 million. In September 2005, Strabag A.G. selected The Robbins Company of Solon, Ohio to design, manufacture and deliver a new 14.4 m (47.5 ft) diameter High Performance state-of-the-art Main Beam Hard Rock TBM to be used in the excavation of the tunnel. In order to meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be supplied as “ready to bore” within a 12 month period after the contract was awarded to Robbins.

Jan 1, 2007