Search Documents

By D. W. Agers

This paper is an extension of previous work evaluating a new extractant, LIX®-64, for recovery of copper from dilute acidic solutions. Large scale pilot plant operations have confirmed the technical and economic feasibility of the process and, with minor exceptions, scale up parameters obtained by previous laboratory work. Operating problems encountered in the pilot plants are discussed. Design parameters for-scale-up to commercial plants are presented and discussed along with a revised capital cost estimate. The future pilot program is discussed, including minor design changes and the effect of entrained organic on dump leaching efficiency.

Jan 1, 1967

By G. L. Black

Choosing a mining method for an underground ore body is a complicated and often iterative process. Advances in technology give the design team an overwhelming array of possibilities for methods and equipment. Hecla's recent discovery of the deep Gold Hunter ore body has given the staff at the Lucky Friday Mine the exciting challenge of determining the optimum mining method. Taking an ore body from prospect to production requires traditional resource characterization, including drilling, delineating and modeling. Developing the mining plan is an evolving process, changing with each new piece of information as the project progresses through exploration and development.

Jan 1, 1998

By Joseph E. Schiller

As part of the Bureau of Mines research on identification of asbestos fibers, a method was discovered for removing asbestos fibers from water. This report describes this process and its theory of operation. The surface charge of amphibole minerals in potable water was found to be negative, and in common with most other silicate minerals, the isoelectric point of amphibole asbestos fibers lies in the pH range 4 to 6. Magnesia is one of the rare oxides with a high isoelectric point of about 11. The surface of magnesium oxide will, therefore, be positively charged in water at pH 6 to 6, while the electric charge an. amphibole asbestos fibers is negative. Because of the electrical attraction of these oppositely charged solids, it was possible to remove negatively charged asbestos fibers from water by percolating water that contained suspended-asbestos through a porous bed of magnesium oxide particles. A bed of 100/200-mesh MgO was added to a glass tube with a cotton plug. Aqusous suspensions of 1 to 10 ppm cummingtonite asbestos (amosite), crocidolite, and chrysotile were percolated through this porous plug of MgO. Even though chrysotile is positively charged below pH 11, MgO is an effective filter medium for removing it. The highly basic MgO appears to cause the chrysotile to flocculate and attach to particles within the bed. Scanning electron photomicrographs indicated that essentially complete removal of the fibers from water was accomplished. Other materials tested as contact filter media and found to be ineffective or only partially effective were sand, calcite, carbon, diatomaceous earth, and cellulose. Acidic alumina collected amphibole fibers but not chrysotile fibers.

Jan 1, 1980

By Dongxu Jia, Chen Cao, Shuangwen Ma, Jun Han, Huibin Ma

Coal bump, or coal burst, is one of the catastrophic disasters in underground coalmine. Among them, approximate 80% of recorded destructive burst events were occurred in mining roadway. The bump panel is often formed by hard coal seam and hard main roof; however, the cause and course of the bump events are not understood yet. This study provides a fundamental theory for the causality and progress of a coal bump event occurred in longwall roadway. Considering hard roof condition commonly existed in bump panels, we think that the abutment pressure induced by suspended roof behind the working face is the trigger of a coal bump event occurred in the roadway. Once high abutment pressure is concentrated on the hard coal seam around the working face, the roof and the coal around the working face form a seesaw-like structure, which leads the roof in front of the working face moving upwards. The movement of roof uplifting in front of the working face is a well evidenced phenomenon in practice, namely, roof rebounding, which causes unloading of the normal stress on the roof-coal interface around the roadway. A rib coal block bump mechanical model has been developed to establish the critical equilibrium equation of the coal block. Result shows that, the force source of coal bump is the horizontal ground stress perpendicular to the rib surface; and the slippage of the coal block is caused by the unloading of the normal stress acting on the roof-coal interface. Based on the causality and consequence theory of coal bump developed in the paper, several new prediction and prevention measures have been developed, including roadway design and in-tunnel reinforcing methods. The commonly used prevention measures in present have also been discussed. This paper presents a comprehensive explanation of coal bumps occurred in longwall roadways, from abutment pressure at working face forming seesaw structure to roof rebounding leading slippage of the rib coal mass into roadway, which provides a fundamental theory for coal bump causality mechanism and prediction and prevention technology.

Apr 26, 2022

The mining industry is one of the three pillars of the Namibian economic development, besides tourism and the fishing industry. Generating 20 % of the GDP and more than 50 % of the export income, half of this amount derives from the diamond mining industry. In 2008, the annual production of 2.2 mio carat achieved an income higher than 1.44 billion Namibian Dollars (more than 750 mio Euro). After the global recession in early 2009, which also caused a significant downcrease in production to only 0.93 mio Carat, the diamond mining industry easily restored itself and the production figures for 2010 are expected to be even higher than those achieved in 2008. Compared to other diamond producing countries, Namibia is mainly producing diamonds of highest quality (jewellery quality), with less than 10 % of the mined diamonds not falling into this category. This high quality stands also for the worldwide highest prize achieved per carat. With 370 $US per carat it is more than four times higher than that of the average South African stone. In 1908 the finding of the first diamonds in the Namib desert close to the coastal town of Lüderitz was reported by a Mr Stauch, railway inspector for the then German colonial railway company. This event immediately triggered a Diamond Rush and subsequently the set-up of the restricted diamond mining area ?Sperrgebiet? through the German colonial administration. In 1913, only five years after the first mining operations had started, the steadily increasing production allowed for more than 20 % of the diamond production worldwide. After the First World War, the new South African government concentrated all mining activities in one organization, CDM (Consolidated Diamond Mines of South West Africa) which in following decades conducted an extensive and detailed exploration of the whole Sperrgebiet and started numerous new diamond mining operations.

Jan 1, 2011

By S. Bhattacharaya, S. Aich, B. K. Nandi

"At present scenario, there has been an increasing demand in the usage of blend coal in power sector; regardless of how, specific knowledge on burning and ignition characteristics and their interactive effects is stingy. In this work a detailed investigation was therefore taken up to study in detail the combustion characteristics of selected coal samples and their blends. Certain parameters were believed to have significant effects on combustion characteristics of individual coal and their blend. Major parameters identified for this purpose included proximate analysis, combustion conditions, heating rate, reaction regions, blending ratios, ignition condition, reactivity (or reaction rate) and burnout temperatures. With the help of these parameters, thermal features and reaction kinetics of the individual and blended samples were investigated through a qualitative and quantitative thermo-gravimetric analysis of two different individual coals and their blend carried out in an oxygen atmosphere from ambient to 800 0C at a constant heating rate of 10 K/min. A significant difference in terms of rate of mass loss with temperature correlated from Arrhenius expression along with coal-coal blend interactions and deviation from their expected behaviour, have been observed between the kinetics of individual and blend samples, the latter showing better ignition performance and comprehensive combustion phase. It was also found that particles having the lowest percentages of volatile matter and ash could possibly be blended with particles having high ash and volatile matter to meet the required burning condition which can be effective in terms of cost savings, improved fuel economy, reduced undesirable exhaust emissions and improved safety of coal burning equipment. Experimental results further indicated that individual samples and coal blend samples have different combustion features in terms of residue left, peak temperatures and activation energies. Thermodynamic activation parameters such as activation energy, pre-exponential factor and order of reaction were computed from the thermal data using the modified form of non-isothermal methods. INTRODUCTION Coal has been the most significant source of energy for India and would remain so at least for the next few decades. About 60-65% of the electricity produced in India is from coal fired power plants. Indian coal is of drift origin and of high ash content. Ash content of the coal burnt in power plants in India is in the range of 30-45%, most of it being Run-of-Mine coal. Most of the power plants in India source their coal from number of mines, most common being multiple sourcing. Usually coal from each source [1] is burnt separately. For various reasons mostly associated with logistics, burning of blended coal is rarely practiced. Blending of coal is practised mainly for improving the quality of available coal and meets the shortage of coal supply. Blending technique is generally practised in power industries to reduce the cost of power generation along with mitigating combustion performance or slagging problem ensuring consistency in as fired coal quality and also for environmental compliance. Blending good quality imported coal can improve coal quality and helps in preserving indigenous coal resources for longer period [2]. Use of blended coal shall reduce load on all boiler components (Mill, CHP, Boiler, AHP) & reduce O&M cost and increase the availability. The main purpose of blending is to get a blended as fired coal having ash, volatile matter and gross calorific value close to design coal and the two coals are to be blended in such ratio proportions that resultant coal blend have desired ash, volatile matter and gross calorific value [3]. For a coal to be blended certain parameters have to be considered to get compatibility with respect to combustibility ( Burn ability) of coal, grindability ( HGI), ash fusion behavior, swelling characteristics of coal, need to be checked"

Jan 1, 2017

By Howard M. Graff

The Inland Steel Company operates five underground iron mines in the Lake Superior District. The two largest of these, from the standpoint of productive capacity, are the Sherwood Mine in Iron River and the Bristol Mine in Crystal Falls, both on the Menominee Range of Michigan. It is at these two mines that we have had our principal experience with belt conveyor installations underground, .At the Sherwood Mine, which has an annual capacity of about 450,000 tons, the first conveyor belt installationwas made in 1947 when conveyors were installed in the main haulage drifts on the 1200 ft, level, It was estimated at that time that approximately 5,000,000 tons would be mined from the stopes above the 1200 ft, level and. that if all this material could be moved to the shaft by belt conveyor, the entire cost of operation, including maintenance and the amortization of the equipment, would be about $,05 per ton, which was slightly more than half of what the cost would have been by conventional tramming methods employing locomotives and cars. Now, ten years later, the 1200 ft, level is almost completely mined out and we have actually removed. 5,200,000 tons and. the average cost of transporting this material to the shaft by belt conveyor has been $.095 per ton. Since there has been a substantial increase in hourly rate of pay and also in the cost of materials since 1947, we feel that the anticipated savings were very nearly realized., The 1200 ft, level installation at the Sherwood consisted of two 36" trunk line conveyors 815 feet long and 380 feet long, respectively, deliverying ore to the shaft. These in turn were fed. by three lateral 36" conveyors which paralleled the sides of the orebody, These gathering conveyors passed under draw points to which ore was brought from the stopes by mea S of scrapers or shaker conveyors, Shaker conveyors were used for a number of years in conjunction with the conveyor belt system of haulage but it was finally concluded that with this particular type of ore, the maintenance on shaker conveyors was excessive. Therefore, more recently, we have gone back to scrapers for the shorter distances and. are using belt conveyors in the scraper drifts for the longer distances. After this belt system had been in operation for about three years, it had proved to be so successful that it was decided to proceed with the same system or. a new level to be opened up 200 feet below. Instead of sinking the shaft and driving a horizontal drift to the orebody on the 1400 ft, level, an inclined conveyor drift was started near the shaft at the 1200 ft. level and driven downwards toward, the orebody at a slope of 15 degrees. The conveyor installed in this inclined drift is 36" wide, 990 feet long, is powered. by a 100 hp motor, and is capable of delivering 300 tons per hour to the 1200 ft, level shaft pocket. It is fed by lateral horizontal conveyors on the 1300 ft? 1400 ft., and 1425 ft, sub levels. Wien the inclined drift was started, the rock was scraped from the breast directly to the rock pocket at the shaft. As the distance increased., double scraping was employed, until the advance had reached 350 feet, At this point a portion of the final conveyor was installed, with a scraper slide near the breast, T e drift was then advanced be scraping on to the conveyor until a sufficient distance had been driven to permit the installation of an additional 200 feet of conveyor. This proved to be a very efficient and economical means of moving the development rock to the shaft and obviated the need of using cars or an inclined skip way, At the present time 85 percet of tie entire mine output is being mined below the 1200 ft, level and is delivered to the shaft via the inclined conveyor. The system appears to be working as well and as economically as did the conveyor systemonthe 1200 ft, level.

Jan 1, 1958

By Anil Kumar

In underground mine production units that employ discrete-vehicle face haulage, feeders are used in the belt network so that vehicles can unload rapidly without transmitting to the conveyor network the high material flow rates that result from rapid unloading. They prevent production bottlenecks at the face, while reducing capacity requirements for downstream materials handling equipment. Similarly, surge bins may be installed at intermediate locations in the network to smooth flows from a number of upstream sources, thereby reducing downstream belt capacity requirements. This paper introduces new stochastic process models to temporally describe loading patterns from unit operations and techniques for computing the probability of various fill levels for the feeder or surge bin. These results may be used to analyze the effect of alternative bin or feeder capacities and discharge rates on the performance and costs of the materials handling system.

Jan 1, 1994

By G. T. Adel

The application of automatic control to mineral processing operations has been gaining momentum during recent years. Many strategies are being developed for controlling crushing, grinding and flotation circuits, however, their implementation in industrial plants is being slowed down because of the costs and difficulties in evaluating these strategies in a systematic manner. An interactive computer simulation package, developed at the University of California, provides the capability of analyzing the process dynamics of mineral processing circuits. This paper presents an overview of the simulator and its application to the case studies of grinding and flotation.

Jan 1, 1983

By C. E. Jordan

The U.S. Bureau of Mines investigated flotation hydrodynamics to improve the recovery of coarse phosphate. Fluid velocity profile measurements were used to characterize the hydrodynamics within commercial phosphate flotation cells and laboratory flotation cells. The effects of agitation, aeration, and pH on coarse phosphate recovery were measured in the laboratory flotation cells and correlated with the hydrodynamics measurements. Test results revealed that the agitation energy and aeration level had a significant effect upon flotation response. By optimizing these two parameters, 92 pct of the phosphate was recovered in a rougher flotation concentrate grading 28 pct P2O5?

Jan 1, 1994

By Wayne A. McCurdy

I welcome the opportunity to meet with you and discuss the work and program of the Office of Coal Research. Our programs are oriented to serve the conservation objectives of the Johnson Administration and of the Nation by seeking out the most efficient and best uses for coal. We believe that even if only a portion of our program is successful, the coal industry and the Nation will benefit far out of proportion to our expenditures. Operating with a budget of $7,220,000 in Fiscal Year 1966, OCR sponsors contract research which offers potential for achieving benefits to the coal industry in the form of new production and new markets. This directs us into many areas of research activity: in coal combustion, in advancements in mining methods and coal preparation, in new uses for coal, and in associated economic and marketing research.

Jan 1, 1966

By H. Colijn

Feeders are used to provide a means of control for the withdrawal of bulk materials from storage units, such as bins, bunkers, silos and hoppers. This control function can only be performed properly as long as the bulk materials flow by gravity to the feeder in a uniform and uninterrupted fashion. A feeder can do many things, but it should never be considered a suction pump: During the past few years various papers have been written and presented on feeders and their application. 1,2,3,4,5,6,7,8,9)* It is not the intent of this paper to cover the same ground, and the readers are therefore ad¬vised to consult the referenced publications for supplementary information. This paper will be confined to some specific design criteria of bin feeders, such as feeder load and power requirements. Special attention is given to the basic design criteria of vibratory feeders.

Jan 1, 1968

By Randhir Sehgal

Heavy media processes have been used for cleaning +28 mesh coals for a number of years, Two applications, i.e., the vessels and the cyclones are widely used in the U. S. for this purpose. The basic reason for the popularity of these systems is their extremely high efficiencies for particle sizes above 28 mesh, However, application of heavy media technology to fine coals below 28 mesh, has been limited due to the following reasons: o Inability to make size separations effectively at sizes below 28 mesh o Necessity of feeding large quantitites of magnetite to the separators o Difficulty of recovering magnetite in the presence of large quantities of coal o High levels of coal contamination in the recovered media, leading to high circulating loads and ineffective control of media gravity

Jan 1, 1981

By Gamal Rashed, Tim Miller, Nicole Evanek

High horizontal stress has been identified as a critical factor affecting roof stability in underground mines, particularly when the immediate roof consists of weak or laminated rock. Numerical models were employed to better understand the influence of caprock thickness, cutting sequences, and the orientation of driving direction relative to maximum horizontal stress on roof stability in underground stone mines. These models were calibrated based on field observations of roof falls from the study mine. The findings of this study enhance our understanding of roof stability under high horizontal stress and contribute to reducing the risk of roof falls in underground stone mines.

Feb 1, 2025

By Guy T. Jr. McBride

World food production is not matching the exploding increase in world-population. Since arable land is limited, ways are being sought to increase yields by turning_ to fertilizer. Phosphate, an essential fertilizer ingredient, is undergoing a period of growth unparalleled in history. The United States is at once the world's largest producer of food and of phosphate rock. Both food and fertilizer output in the United States are being enlarged to meet the demands posed by the threatening world food crisis. New phosphate deposits are being developed in Florida and North Carolina to assure the United States' continued preeminence in this vital resource. Large fertilizer complexes are also being constructed with an eye to both domestic and foreign markets. The growth of the U. S. phosphate industry has been characterized by developing technology in the processing and distribution of phosphate raw materials. The trend from low analysis to high analysis materials accompanied by a change from a large number of small fertilizer plants oriented toward the marketplace to a fewer number of large plants located at the raw material source is illustrative. These changes in technology and distribution have also been important factors in the development of new mining areas in Florida, the Western States and North Carolina.

Jan 1, 1966

By Allan D. Fernie

Growing interest in pit crushing and conveying is evident from the many articles, technical papers, and new equipment development recently presented. Application of a pit crushing and conveying system is complex, as many factors such as mine design, production scheduling as well as initial and ongoing capital and operating costs must be thoroughly and realistically examined. This paper will address the fundamentals to be considered and review several approaches to developing a total system for a new and existing mine situation. The planning function will be outlined and operating and design criteria defined to interface the mining operation and the pit crushing conveying system.

Jan 1, 1983

By T. W. Newell

Small tonnage ore bodies can be developed at a profit on a short life basis. Such is the case of the Bardon Mine in. the Big Indian Mining District in San Juan County. Utah. Faced with a small initial tonnage of high grade uranium ore, the Shattuck Denn Mining Corporation Engineers developed some new ideas for sinking the shaft and planned extraction to warrant the capital risk to mine a limited reserve. The Bardon Mine is located fifty miles southeast of Moab, Utah in the south end of the Big Indian Mining -district. Shattuck Denn Company, a wholly owned subsidiary of the Shattuck Denn Mining Corporation, manages and operates the property under an operating agreement with Kerr-McGee Oil Industries, Inc. of. Oklahoma City. Oklahoma, and Anderson Development Corporation of Albuquerque, New Mexico. Based. on Kerr-McGee drilling., a tabular ore body about 350 feet long by 250 feet wide with an average thickness in excess of seven feet was indicated.- The ore body strikes easterly-westerly and dips from nine to twelve degrees to the south. Uraninite is the dominant uranium ore mineral associated with vanadium. The ore occurs in an arkosic conglomeratic sandstone with some interfingering of mudstone and shale in the Mossback member of the Chinle formation in contact with the underlying Cutler formation. The ore horizon is overlain with 40 to 60 feet of mudstone and shale. Fortunately, the back. immediately over the ore is a reasonable competent shaley sandstone which has made a fairly good. environment for roof bolting.

Jan 1, 1960

By Scott A. Norby

Kennecott's Ray Mines Division (RMD) is located in central Arizona. The pit and silicate plants are located at Ray while the 27,500 tpd concentrating facilities are located at Hayden, approximately 20 miles away from the pit. Ore is delivered in 100 ton railroad cars, 60 cars per train via the Copper Basin Railroad. The side discharge cars are dumped into a 6,000 ton trackhopper. There are 6 Nico feeders, two per belt. Three 48" belts transport the -8" ore to three 7' standard (secondary) Nordberg crushers. Each crusher is preceded by a 6' x 12' Tyler double deck screen. The secondary crushers are open circuit. The -1/21t material from the screens is transported directly to the fine ore bin at the mill. The discharge from the crushers and the intermediate product -2 1/411 x +1/2" is conveyed to a surge bin. The tertiary crusher feeder belts discharge onto five 61 x 161 Tyler double deck screens, each followed by a 7' shorthead (tertiary) Nordberg crusher in closed circuit. The -1/2" product joins the -1/2" ore from the secondary crushers and both are conveyed along a 42", 4,230 foot long belt to the fine ore bin that feeds the grinding circuits. When hard ore is experienced at the concentrator the daily throughput decreases by up to 10%. This coupled with the fact that the ore is generally becoming harder with mine depth provided the incentive to improve the performance at the crushing plant.

Jan 1, 1986

By Robert W. Cope

"Mining began, in the Colstrip area in the 1920's by the Northern Pacific Railroad. The coal was used for steam locomotives until 1957, when the advent of diesel power made them obsolete. In 1959, Montana Power Company purchased the Northern Pacific properties including the mining equipment, coal leases and the town of Colstrip. Western Energy Company, a wholly owned subsidiary of Montana Power Company was formed in 1966 to manage the mining operations in Colstrip. The Rosebud Mine officially re-opened in 1968 to supply coal for Montana Power Company's J. E. Corette Plant In Billings. Since 1970, Long Construction has operated the mine equipment for Western Energy Company". The Rosebud Mine is located in Southeast Montana and supplies coal to two 350 megawatt power plants located in Colstrip and one 180 megawatt plant located in Billings. Approximately 30 percent of Western's annual production is consumed by these plants. The remaining production is shipped to the mid-west and burned by utility companies and municipalities.

Jan 1, 1981

By C. G. Snavely

Martin County Coal Corporation produces coal from seven continuous miner sections in two coal seams which are often interlaced with rock partings. Because of high clay content and coal oxidation, all minus 100 mesh material is discarded in the preparation process. We began experimenting with various drum lacings on continuous miners in 1983 to improve product size consist and increase machine cutting rates. To date, + 6.35 mm material has increased from 61 to 73% of mined product, minus 0.15 mm material has decreased from 6% to 4% of product, and machine cutting rates have increased by 50 percent.

Jan 1, 1985