Search Documents

By Richard R. Klimpel

Part 2 of this article continues the discussion of a 10-year, multimillion dollar research and plant testing program on slurry rheology and grinding circuits. The first part of the article (ME, Dec. 1982) presented the basic concepts identified by the research and some laboratory test results. This section Illustrates typical Industrial scale test results and Identifies some industrial operating implications of controlling rheology by different methods. At least four controllable factors decide the rheological character of a slurry-slurry density or percent solids, particle size distribution, chemical environment, and slurry temperature. The second factor has two interrelated facets: the shape of the particle size distribution which controls packing behavior of the solids, and the fineness of the distribution. Finer particles increase interparticle forces and viscosity. As indicated in Part 1, during a given grinding test it is possible for all four factors to change. However, regardless of the particular settings of the four factors in a given test, if the resulting rheological character is either dilatant, pseudoplastic, or pseudoplastic with yield, the associated breakage rate is correlated with the current rheological character. It is obvious, for example, in batch grinding tests run at constant percent solids, that the second and third factors, where appropriate, are changing during grinding because size distributions are changing and the production of fresh surface area takes up unadsorbed chemical. Thus the corresponding rheological character change in batch tests with increasing grind time would be dilatant to pseudoplastic to pseudoplastic with yield. The degree to which this transformation occurs depends on the changing setting of the four factors over grinding time. In continuous grinding tests, one might logically expect that dramatic changes in any one of the four factors will be less likely to occur. It will be shown that continuous mill operations offer some unique opportunities to take advantage of possible rheological transformation by more direct operational control of the settings for the four factors. One extra observation noted in the rheological studies was the variability in the location and extent of region B (pseudoplastic behavior) for the various coals and ores tested. The location of region B was usually in the region of 45-55% solids by volume and was of the extent of 0-8%, or 2-11% with chemical addition. The corresponding increase in net production ranged from 0-10% in region B and 0-21% in region B&apos;. When region B is small or zero (no pseudoplastic character is exhibited) no increase in production will be observed and the use of chemicals is often marginal. There are several reasons for some materials exhibiting this quick transformation from dilatancy to high yield values often at surprisingly low percent solids by volume such as 30%. One condition identified was for materials containing high levels of viscosity-producing elements such as- carbonates or clays. A second condition documented was for materials that exhibited unusually fine primary fragment distributions (fine B1,; curves). This corresponds to materials having small y values of < 0.5. Such a slurry developed a yield value quickly during grinding because of the rapid buildup of fines. A related problem can be presented by materials exhibiting excessively coarse primary fragment distributions, y values > 0.9. Breakage of this type of material produces size distributions that give poor packing efficiencies even at long grind times, thus hindering the normal rheological transformation presented earlier. A final condition that can cause the occurrance of region B to be small or zero is when the media void volume filling of slurry is < 100%. Figures 5a and 5b use previously published data of this study to demonstrate the influence of solids loading and weight percent solids on the net production of taconite ore in a laboratory batch ball mill. In particular, Fig. 5a illustrates several trends not generally recognized until this study. They include these two: • Increased slurry density allows for increased solids loading before passing through the maximum in the net production curve where the fall-off is due to non first order breakage. • The use of rheology control chemicals such as GA-4272 allows this trend to be extended to higher slurry loadings with an increase in net production over any previous condition by keeping grinding first order. Figure 5b shows the same data as Fig. 5a plotted for constant weight loadings. These various figures of net production versus percent solids show the location and extent of the regions A, B, and C presented in Part 1 as a function of solids loading. It is obvious that the rheological transformation pattern described earlier does not hold true for slurry loadings corresponding to less than the void volume of the media, which is also a region of

Jan 1, 1983

By Robert F. Kaufmann

INTRODUCTION In response to the Uranium Mill Tailings Radiation Control Act (Public Law 95-604, Section 114c), a report has been prepared by the U.S. Environmental Protection Agency (1980) which describes the potential health and environmental effects associated with uranium mine wastes. The author was responsible for the geology, hydrology and aqueous pathways analysis portions of the report. All potential sources of contaminants, solids, liquids, and airborne emissions, which might cause adverse impacts upon the environment or health of nearby populations were considered. Wastes at both active and inactive uranium mines (Hans and O&apos;Connell, 1981) are described and assessed with respect to dose and health effects (Blanchard et al. 1981). The emphasis of this paper is on the liquid emissions and the aqueous pathway. Model uranium mines were developed for surface and underground mines. The model underground mine was placed in New Mexico while the model surface mine was in Wyoming. Development of a generic assessment was complicated due to the inherent variability of uranium mines. Also, most information available relates to uranium mills rather than to mines, or reported measurements were often influenced (biased) by wastes from a nearby mill and did not specifically reflect mine discharges. Consequently, the assessment presented is often based on conservatve (maximizing) assumptions which are identified as such, and which were based on knowledge from field investigations, available literature, and consultations inside and outside the U.S. Environmental Protection Agency. Maximum use was made of available data, supplemented with limited field studies in Colorado, Texas, New Mexico, and Wyoming. PREVIOUS INVESTIGATIONS Stream survey work in Colorado by the Water Pollution Control Commission and the U.S. Geological Survey (Moran, 1974; Wentz, 1974) mentioned a portion of the Uravan Mineral Belt and uranium mines therein, but the work did not emphasize uranium mines. Significant amounts of acidity and total trace metal concentrations were found in streams from 18 different mining areas. Dilution and chemical precipitation below mine drainages decreased concentration and increased the pH. Given enough time and distance, the streams recover naturally, but the accumulations of trace metals in the sediments increase. Field observations in 1971-72 of streams in most of Colorado indicated that approximately 724 km of streams in 25 different mining areas were adversely affected by mine drainage (Wentz, 1974). Discussions of the impacts of uranium mining on water quality or quantity are incidental in numerous impact statements and environmental reports prepared by industry and (or) the U.S. Nuclear Regulatory Commission as an integral part of licensing or relicensing uranium mills. Coverage on mining is usually minor as the principal focus is on milling impacts. The same is true for the recently prepared generic EIS on regulation of uranium milling (U.S. Nuclear Regulatory Commission, 1979). Radiochemical assessment of surface and groundwater in uranium mining districts of New Mexico is done by self-monitoring programs associated with NPDES permits. Also, radiochemical assessment studies have been funded by the New Mexico Environmental Improvement Division and U.S. Environmental Protection Agency. Unfortunately, there has been no concerted effort to prepare broad assessments of the cumulative impacts of mining and milling in areas of interest in Texas, New Mexico, and Wyoming. Critical review and synthesis of these types of data can produce rather useful information. For example, the publication "Water Quality Impacts of Uranium Mining and Milling Activities in the Grants Mineral Belt, New Mexico" (U.S. Environmental Protection Agency, 1975) addresses the groundwater and surface water changes as the result of extensive uranium mining and milling production in a relatively confined area. A more recent report by the Wyoming Department of Environmental Quality summarizes 16 years of aqueous radium and uranium data. The study reports significant amounts of radium-226 and uranium were present in surface water in the Shirley Basin as a result of inadequate mine water treatment (Harp, 1978). In Texas, surface water and groundwater monitoring conducted by industry, as well as by State and Federal agencies, reveals little or no change of chemical quality attributable to uranium mining and milling (Gesell, 1977; Kallus, 1976). This conclusion is based on 586 samples collected from 198 stations over a period of 39 years, but primarily from 1961 to 1975. The State monitoring program by several agencies is continuing, but data reporting and interpretation is lagging. One survey (Itin, 1975) showed that none of the mine water from the 10 lakes that were sampled was suitable for human use. The lakes were also unsuitable for irrigation due to mineralization of the water by sulfate, chloride, and TDS. One of the 10 was suitable for stock watering.

Jan 1, 1981

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

10.1 I~RODUC1&apos;ION In order to understand the effects of surface subsidence due to underground mining on the ground water hydrology, a brief introduction to the rate, direction, and general pattern of ground water movement in aquifers is necessary. Ground water movement in an aquifer is controlled by aquifer lithology, structure, permeability, water levels, topographic set¬ting, and pumping patterns (Sgambat et al., 1980). Fig. 10.1 shows an idealized flow pattern of ground water in a hilly terrain (Coe and Stowe, 1984). The hill is made up of a series of interbedded permeable aquifers (mostly sandstone) and confining units (mostly shale). Since sandstone is porous and permeable, ground water moves through it downward and laterally until it reaches the interbeddings of the confining unit immediately below. The ground water then moves laterally along the interbeddings, be¬cause the confining unit is less permeable, and comes out as springs on the surface at the intersection of the aquifer and the confining unit. If there is a ground water table in each aquifer, it is a perched water table (e.g., right side of Fig 10.1). On the other hand, if the ground water recharge is larger than can be drained out, the interbedded permeable aquifers and confining units will be filled with water and a ground water table will exist only at the uppermost permeable aquifer. This is the semi-perched water table (e.g., left side of Fig. 10.1). There are three ground water flow systems: shallow, interme¬diate, and deep. Shallow flow systems occur near the land surface and the surface drainage system. The flow depth ranges from a few to several hundreds of feet with a resident time of a few weeks to a few years after entry, depending on the permeability of the rock strata. In a shallow flow system, the drainage coincides with sur¬face run-off water divides. Intermediate flow systems occur in minor hills some distance away from surface drainage. The travel distance ranges from several hundreds to several thousands of feet, the travel time from several months to tens of years. These systems are less dependent on seasonal recharge or discharge. In deep flow systems, the ground water travels from thousands of feet to miles, and transfers between surface basins. The travel time ranges from several tens to several hundreds of years. The systems generally receive recharge over a large area on major mountains and dis¬charge into major stream systems. 10.2 CASE STUDIES There are two ways of monitoring water wells for studying the effects of dewatering due to underground mining, i.e., water level and piezometric level. The water level is the water elevation in a water well that has penetrated two or more aquifers. Thus it indi¬cates the combined flow of all the aquifers that the water well intersects during the time of measurement. The piezometric level is the level to which water rises in a piezometer cased to a specific aquifer, and coincides with the pressure level of water in that aquifer. Therefore piezometric level reflects the water condition in that particular aquifer to which it is confined, while the water level represents the total yield of a water well without regard to the source of water. For instance, if a water well intersects two aqui¬fers, and if the lower aquifer is affected by undermining and goes dry while the upper aquifer does not, the water level in the well will drop, but may never go dry. Under this condition, the data obtained by monitoring the water level do not indicate the true behavior of the individual aquifers, especially if they are located at widely separated heights. 10.2.1 WATER LEVEL EFFECTS The effects of underground mining on ground water flow have been the subject of many investigations (Booth, 1984; Coe and Stowe, 1984; Owili-Eger, 1983; Rauch et al., 1984). However, the problems are very complicated, as have been exemplified by the conflicting conclusions reached by various investigators in var¬ious case studies. The most dramatic examples were described by Coe and Stowe (1984). In the first case (Fig. 10.2), the coal seam was 5 ft thick with cover from 400 to 800 ft deep. The majority of water supplies came from a sandstone aquifer in most ridge tops. When the face of the Panel No. 3 passed under it, dug well WW-1, which was approximately 670 ft above the coal, went dry, while the water level in Borehole B- 1, which was located at the center of Panel No. 4 with the bottom reaching the coal seam, also dropped about 160 ft. In Panel No. 5, the developed spring DS-2, which originated from the surface of the sandstone/shale contact and was approximately 750 ft above the coal seam, stopped when the face passed under it. The water level in the dug well W-2, which was dug into the shale about 700 ft above the coal seam dropped about 22 ft, but the well did not go dry. Therefore, nearly every spring or well located above or near the active panels was affected by longwall mining. In the second mine (Fig. 10.3), the seam was 5 ft thick with cover from 200 to 400 ft thick. Dug well DW-2, the bottom of which was 35 ft deep and approximately 330 ft above the coal seam in a perched sandstone aquifer, went dry right after the longwall passed under it. Drilled well W-3, in the sandstone aquifer, about 220 ft above the coal seam, experienced a 75-ft drop in water level when the face was under it, but showed some re¬covery after the face had passed under it. Ponds P- I and P-2 were developed in shale bedrock and were spring fed. They were not affected by longwall mining. Pond P-3 was developed in the sand¬stone aquifer, and its water table showed some decline when the face passed under it. Spring ST-1, which originated from Pond P-1 and was fed from several tributary valleys, was affected by longwall mining, probably because it passed across the panel edges where tension cracks drained off the water. Although the overbur¬den in case 2 was about half of that in case 1, the majority of water resources were not affected by longwall mining. Coe and Stowe (1984) attributed this discrepancy to: (1) a higher percentage of clays, shales, and claystones, resulting in a lesser degree of inter¬connected fracturing, and (2) a less rugged topography resulting in a less localized ground water flow system. Therefore, in order to assess the effects of underground mining, the premining ground water flow patterns, topographical, lithological, and meterological conditions must be known. Booth (1984) also monitored the ground water effects of a longwall mine (Fig. 10.4) in a seam 5 ft thick and 300 to 800 ft deep. There were three major aquifers: Morgantown sandstone approximately 30 ft thick and 630 ft above the coal; Saltsburg sandstone of up to 50 ft in thickness and 520 ft above the coal; and

Jan 1, 1992

By A. Simon, J. Weyer, J. Brune, V. Zhiteneva

"Reiche Zeche is a lead-zinc-silver deposit in Freiberg, Germany, that was mined for over 800 years. Since 1969, Reiche Zeche has been a teaching and research mine with numerous adits for dewatering large amounts of inflowing water. Infrequent metal water quality monitoring in the 1980-1990s and flooding of the mine in 2002 led to a lack of relevant data. New measurements were taken at different level adits and ore veins for comparison to historical values, revealing pH levels as low as 1.95, conductivity as high as 22000 µS/cm, and an overall trend towards less acidic waters. INTRODUCTION Reiche Zeche is part of the Himmelfahrt Fundgrube, a former iron ore mine in Freiberg, Germany, in the Erzgebirge mining region of Saxony. The polymetallic sulfide ore found in Freiberg was mined from 1168 to 1969, and though it is no longer producing ore, Reiche Zeche remains as a teaching and research mine for the Technische Universität Bergakademie Freiberg. The most important ore minerals mined were sphalerite, galena, pyrite, chalcopyrite, and silver, and important gangue minerals include calcite, fluorite, barite, siderite, and quartz (Zänker et al 2002). Over one thousand ore loads were mined from this region during operation, which was ceased in 1969 after the lower part of the 700 meter depth was flooded, leaving only the top 200 meters under the surface open for research and teaching. Mined materials from this region can be separated into high grade ore and waste rock. High grade ore, composed of pyrite, sphalerite, galena, chalcopyrite, and arsenopyrite, was brought to surface for smelting during mine operation, and spaces were backfilled with waste rock, which is the primary site of sulfide oxidation and acid mine drainage (Haubrich and Tichomirowa 2002). The waste rock includes remnants of ore from ore loss, veins which were too small to mine, or ore minerals within host rock. Waste rock is primarily composed of biotite gneiss, with sulfides including jarosite, gypsum, minor anglesite, scorodite, and sulfur (Haubrich and Tichomirowa 2002). When weathered, the gneiss forms clay minerals such as illite and kaolinite (Haubrich and Tichomirowa 2002)."

Jan 1, 2016

By T. R. Ley

"INTRODUCTION Brutally honest mining executives will tell you that “safety is job #1 but.. dollars are also extremely important”. When economic times are tough, as they are now in mining, it can feel like you need to choose between safety and cost control. Leading edge companies know that it is excellence at both that provides the best performance. FLUID POWER SYSTEMS Fluid power systems are ubiquitous in mining – longwall systems, continuous miners, drills, haul trucks and excavators, etc. And fluid power systems are getting more powerful and using higher pressures to move greater volumes and achieve higher productivity. Average operating pressures in mobile equipment has been rising to 450 bar (6,500 psi) over the last decade. With increased system pressure comes ever increasing levels of stored energy. Stored energy that, if released in an uncontrolled fashion, can do tremendous harm to people and things.Fluid power systems are composed of pipe, flexible hoses, pumps, valves and actuators. They are filled with fluid (mineral oil or fire-resistant) to transmit power to where it’s needed for performing work. With time and use fittings can loosen, component performance diminishes and hoses wear and tear. In hostile environments, like coal mining, hydraulic hoses can fail in as little as 2 years according to DGUV (umbrella association of German Accident Insurers), maybe sooner in some particularly challenging environments. FLUID POWER SYSTEM SAFETY While appearing simple and benign on the surface, fluid power systems, particularly such systems on mobile equipment, have many potential hazards. Hazards that most workers aren’t aware of – particularly young, new hires. And those hazards that can quickly turn deadly. During the past couple of years, including at last year’s SME Conference, I talked to a wide variety of mining people about high pressure fluid injection injuries. Some people, often with little or no field experience, never heard of it. But, people with mine operations / maintenance experience were almost always aware of such injuries.Some had even seen it happen right in front of them. But most claimed it didn’t happen all that often. It just wasn’t seen as a problem!"

Jan 1, 2016

By Klaus Rieker

"Since the mid-19th century the River Emscher in the German Ruhr District has been used for disposing of wastewater. In the early 1990s, it was decided to replace the existing open wastewater system with a sewer system and to restore the River Emscher to its natural state. The major Emscher conversion project is divided into a large number of individual schemes, with construction phase 30 being the largest. By applying the pipe jacking method, interlinking tunnels with section lengths in excess of 1,100 m are constructed. USAGE OF THE EMSCHER OVER TIME The 85-km long river Emscher flows right through the Ruhr District. It has its source to the east of Dortmund and flows into the river Rhine near Dinslaken (Figure 1).The Emscher has been used to dispose of wastewater since industrialization began about 200 years ago. Intensive coal mining over the years led to considerable subsidence causing stagnant sewer areas which in turn led to typhus and other deceases. Thus in 1899, the Emschergenossenschaft was founded to create an efficient interceptor system for a catchment area of 865 km² through lining, raising and Emschergenossenschaft decided to free the waterways of the Emscher system from sewage and to improve them in ecological terms by 2020. A budget of 4.5 billion euros was earmarked for this purpose.The construction of sewer conduits began in order to no longer transfer the wastewater into the Emscher. The currently ongoing construction of the “Emscher Interceptor” - the main sewer - represents the heart of the Emscher conversion project. The interceptor will run along the river over a length of 51 km. Three pumping stations are required to confine the sewer’s depth to elevations between 15 and a maximum of 40 m below the surface. Since early 2012, the Emscher has been free from wastewater east of the Dortmund-Deusen clarification plant. There are two further clarification plants situated along the Emscher, which treat the still contaminated river water down-stream. Once the Emscher Interceptor is in operation, they will receive wastewater solely from the tunnel system."

Jan 1, 2016

By Z. Sample, S. Kaushik

"INTRODUCTION Industries around the globe have been making significant advancements in recent years due to innovations in automation technology. With the implementation of modern automation technology, professionals in process automation or plant operations can expect significant and exciting change, and the mining and mineral processing industries are no exception. From 2000 to 2010, the International Council on Mining & Metals (ICMM) reported that an increased output and increased value of most metals has resulted in a rise in global metal and mineral process industries from $214 billion to $644 billion. [1] Since most productivity increases in mining and mineral process industries have been achieved through the ability to process lower grade ores with improved efficiency and larger equipment, these industries have begun to adopt advanced automation and control technologies. Despite a growth slow-down, the mining and mineral processing industries are poised for continued and sustainable growth and development due to an increasing demand for energy minerals and emerging technologies requiring minerals and metals previously not demand. However, as these industries becomes more automated, new challenges are arising on the horizon. DEMOGRAPHIC TIME BOMB John Payne from BP is credited with first using the term Demographic Time Bomb to describe the upcoming crisis in the process industry in finding experienced operations personnel. From a survey of 912 mining professionals, Stratum International found that a mere 0.4% of senior level candidates were between the ages of 25 and 34 and a similar proportion aged over 75 years. This indicates that there is both a deficiency of young skilled workers and a skilled workforce that is retiring earlier than the previous generation. Combined with data published by the US Department of Labor stating that the median age of the mining workforce is approaching 50 years old, this implies that these skilled mining and mineral process professionals are an aging population with irreplaceable knowledge and experience that are expected to retire in the next 5-10 years. While it is projected that the labor pool will be sufficient to fill open positions, the real question is if this young workforce will have necessary skill sets and experiences."

Jan 1, 2015

By R. L. Taylor, S. D. Abbott

"INTRODUCTION Mines are filled with a mixture of gases, some of which are toxic, flammable, explosive. Others can be early reporters of potential problems. It has previously been shown that analysis by gas chromatograph can the most accurate conventional analytical tool for common mine gas mixtures when used correctly. There are some other detection methods (e.g hand held sensors), but they do not detect many situations which are immediately dangerous to life or health (IDLH). Examples include explosive hydrogen mixtures, toxic carbon dioxide levels, and some explosive mixtures of methane with oxygen. (Reference our previous paper). There are several reasons for mines to consider onsite GC analysis. (1) Timeliness of results. Samples can be taken and analyzed immediately. Samples do not have to be shipped to a lab and wait for results. (2) Ability to run greater number of samples a lower for the same cost. This allows mine to increase the number of samples taken to be more informed about the gases/conditions of the mine without the worry of financial constraints. (3) Fewer sample media needed, and there is no wear and tear or cost from shipping them offsite. When samples are shipped offsite, those sample media cannot be used to take until the lab returns them when the analysis is done onsite, the sample media can be used again almost immediately. However there are several challenges associated with using GC to analyze mine gas samples onsite. To date there has been a clash of the requirements for a successful analysis, the capabilities of the technology, and the practicalities of implementation. The purpose of this paper is to discuss some of the difficulties in getting accurate reliable data and doing so in an economic way. This whole measurement activity is a cost center for a mine, so there are economic concerns for the mine to address. These concerns are mainly staffing costs, capital costs, maintenance, and consumables costs. A properly staffed and equipped analysis lab, including burdened overhead, costs about $500K per year. At a sampling rate of 10 per day, this is about $140 per measurement for a proper onsite lab."

Jan 1, 2016

By J. B. Fletcher

Miami Copper Company has used conveyor belts underground since 1947, At that time, the draw level for a portion of the orebody was only 25 feet above the haulage level To get the main haulage drifts as far away as practical from under the stoping area, 301, belt conveyors were used for lateral transfer, If the haulage drift was kept in good ground., a satisfactory draw of these stopes could be effected in that repairs to the conveyor drifts could be accomplished while drawing ore from the stopes. Some 7,400,000 tons of ore were mined with the 301d belt conveyor at a belt cost of approximately $0,004 per ton of ore. When the mining plan for a new section of the mine was laid. out in 1953, it was decided to use belts to collect the ore from the higher draw levels, and. move the ore laterally to centrally located concrete ore passes for transfer to the main haulage level (See Cut #1), The final plans used belt conveyors too collect from 3 stopes: on the 570 level, 2 stopes on the 720 level, and one stope on the 900 level. The six stopes to be mined in this manner would produce about 8 million tons of ore, and the sequence of mining was such that not more than four 400 feet conveyors would be in use at one time, Four conveyors using 36 inch, 4 ply belting were designed by the mine engineering office and fabricated at the mine shop, so that no piece was longer than 10 feet, and. the heaviest piece was the 25 horsepower motor, The head drive section, and the tail-pulley-takeup section were of bolted construction so they could be broken down for easing moving, Due to the size of the mine openings, the belt had to be transported into the mine in 400 feet rolls, requiring two splices for an installed belt. A torque arm speed reducer was used with a V -belt drive which made it possible to change the speed of the conveyor by changing the diameter of the V-belt pulley (See Cut #2).

Jan 1, 1958

By Donald C. Wotring, Douglas A. Gabriel, Michael G. Vitale

"The Northeast Ohio Regional Sewer District (NEORSD) recently completed the 24-foot diameter Euclid Creek Tunnel using a steel-fiber reinforced concrete segmental lining. During construction HMM, the McNally/Kiewit JV, CSI/Hanson JV, and the NEORSD performed a test program to evaluate replacement of steel fiber with synthetic fiber. A section of synthetic-fiber-reinforced cast-in-situ lining was also placed as part of the permanent works for the starter and tail tunnels. Laboratory and field testing were performed on two complete segmental rings reinforced solely with synthetic fibers. This paper summarizes the testing program, construction, and results of the synthetic-fiber-reinforced CIP lining and concrete segments. INTRODUCTION The principal feature of the Euclid Creek Tunnel (ECT) project is a CSO storage tunnel that is one component of the Northeast Ohio Regional Sewer District’s (NEORSD) Easterly CSO storage and conveyance system. The tunnel, shafts, and appurtenant facilities will be used for the collection and storage of CSOs from the northeastern part of Cleveland, Ohio and subsequent conveyance to the NEORSD’s Easterly Wastewater Treatment Plant for treatment. The ECT project includes five drop shafts that extend as deep as 220 feet below the ground surface. The ECT alignment and shaft locations are shown in Figure 1. Traditionally in northeast Ohio, tunnel excavations were supported with a two-pass system using steel ribs and timber lagging, followed by cast-in-place concrete. Control of rock overbreak proved difficult with large-diameter two-pass operation, and invert degradation led to train derailments. To mitigate these risks, the ECT was supported using one-pass, precast, bolted, gasketed concrete segments reinforced with steel fiber alone. Tunneling operations were very successful and experienced no significant delays or claims. As a result of the positive ECT experience with steel fiber-reinforced segments, Hatch Mott MacDonald, LLC (HMM), McNally/Kiewit (MK) joint venture, CSI/Hanson (CSI/H) joint venture, and the NEORSD performed a test program to evaluate replacement of steel fibers with synthetic fibers in segmental rings. This paper presents the laboratory and field testing program, construction, and results of the synthetic-fiber-reinforced cast-in-place (CIP) lining and concrete segments."

Jan 1, 2016

By K. Lagnese, C. Robinson, S. Muddasani

"Mine water generated from underground coal mining operations contains both dissolved and particulate solids. Dissolved solids primarily consist of sodium, calcium, magnesium, potassium, chlorides and sulfates. When discharged to a receiving stream without treatment, these constituents create a potentially toxic environment for aquatic life. A case study is presented to discuss how a centralized treatment plant treats mine water from six locations to meet discharge limitations for chlorides. Located in West Virginia, this facility consistently achieves less than the NPDES permit limitation of 218 mg/L chlorides in the discharge while generating almost zero liquid waste. The dissolved solids concentration in the influent ranges between 5,000 and 10,000 mg/L, with chloride concentrations of 1,000 to 2,000 mg/L and sulfate concentrations of 2,000 to 6,000 mg/L. The mine water is treated using advanced treatment technology to produce clean water for discharge or reuse. The treatment process comprises aeration, softening, filtration, reverse osmosis, RO reject softening, evaporation, crystallization, final effluent remineralization and sludge dewatering. The solid waste generated in the treatment process is landfilled on site. The leachate is sent back to the facility’s thermal treatment process. Because no liquid waste leaves the property, this plant is termed a “Zero Liquid Waste” (ZLW) facility. INTRODUCTION The advanced water treatment system was built to meet a new 218 mg/l regulatory limitation imposed by the West Virginia Department of Environmental Protection for chlorides discharged to surface waters. The system is designed to treat a maximum flow of approximately 5 million gallons per day (795 m3/h) of mine water. The treatment process utilizes reverse osmosis (RO) membrane treatment to achieve the effluent criteria, and evaporation and crystallization technology to manage the RO concentrate from the water treatment process. As a result, the system produces clean water for discharge while generating zero liquid waste. The effluent water can be used for industrial purposes or discharged to a receiving stream. A Water Impact Index (WIIx) study indicated that discharge of this high-quality water into the Monongahela River watershed may improve the water quality for downstream water users. The waste produced in the treatment process, including softening sludge and salt, is disposed of in an on-site landfill."

Jan 1, 2015

By Takayoshi Otsuka, Taher Elsamni, Ashraf Bou-Krisha, Takaya Takimoto

"INTRODUCTION Tunnel is a closed space structure and it is necessary to ensure the sufficient time and route for safe evacuation for the tunnel users in case of a tunnel fire. In order to do so, damages and collapse of the tunnel linings and the secondary disasters can be avoided. Furthermore, the road tunnel is one of important infrastructural facilities and stopping its function for a long time for a tunnel fire could cause a great economic loss. Therefore, the tunnel structure shall be the one which can be repaired as soon as possible, and the fire protection methods need to be selected among those which enable the service to start as early as possible. The necessity of the fire protection works is evaluated for the tunnel structure with the consideration of the expensive tunnel construction cost and the economic effects of the tunnel service. Naturally, the fire protection works, which can protect the tunnel linings from the tunnel fire with small repairs, are inevitable. Design engineers of the fire protection works estimate the scale of fire from the degree of damages on the linings and its repair cost, the effect of fire extinguishers placed inside of the tunnel, the secondary disasters in accordance with the tunnel lining damages if any, and the ratio of fire protection cost calculated from tunnel operation cost. Based on this information, the engineers design the fire protection works according to the permissible limits Among the design cases of the tunnel fire protection in Japan, as shown in Table 1, there is no cases that used the fire temperature-time curve to design the fire protection works for large fire caused by vehicles catching fire. However, the most of cases used 30-60 minutes for fire duration based on the entry prohibition of dangerous goods carrying vehicles or the effect of early fire fighting. This paper will study the variation between different methods used for fire protection in road tunnel in Japan to evaluate them and try to found some recommendations. Especial l care will be attention to Polypropylenes (PP) which is starting to be applied lately."

Jan 1, 2016

By P. Knudsen, S. Rosenthal

INTRODUCTION In 2010, Montana Tech was gifted 65 acres of land immediately west of the campus. The parcel of land included an old silver mine called the Orphan Boy Mine. The Orphan Boy and its sister, Orphan Girl, were developed about1895 and operated until 1956. In addition to the gift of land, a significant industry gift was obtained to develop a first class training facility, which we call the Underground Mine Education Center (UMEC). The UMEC has been funded primarily by industry through donations of dollars, equipment, and supplies. The UMEC is a unique hands-on, educational environment for today’s students who are being trained to find, develop and process the worlds' natural resources. The center complements courses in mining engineering, geological engineering, environmental engineering, metallurgical engineering and occupational safety and health. It also serves as a as research facility utilized by students and faculty, and other organizations interested in doing research a hard rock underground mine. LOCATION The Orphan Boy and Orphan Girl Mine are located approximately 700 feet (ft.) apart and the Orphan Girl Mine is part of the World Museum of Mining. Underground they are connected on various levels and all levels below the 100 ft. level are currently flooded. The Orphan Boy mine was 804 ft. deep and Orphan Girl was 3200 ft. deep. The surface locations of the two mines and some of the underground workings on the 100 ft. level are shown on Figure 1 (2015). CONSTRUCTION Land ownership was gifted from BP/ARCO in 2010 and planning started immediately. In June of 2011, site development for the decline to the 100 ft. Level of the Orphan Boy began with a satisfactory portal site developed (Figure 2). We hoped to be able to start driving the decline in July. However, the portal was sited approximately 125 ft. away from a natural gas line that bisected the Montana Tech campus. While outside the right of way for the line, Northwestern Energy requested that no blasting be performed near the gas line until such time as the gas line was abandoned in the fall so decline development was put on hold. The gas line was officially abandoned in January of 2012.

Jan 1, 2019

By J. Castaneda, J. Schmidt

"INTRODUCTION Chino is an open-pit copper mining complex faced with intricate material routing requirements. Historically, this was challenging at the mine, in part because the shovel dig plan, haul plan, and dump plan were prepared completely separately. The mine now uses an integrated workflow for faster evaluation of schedules, which facilitates preparing balanced cutoff grade-to-equipment requirements, supports better mineral production, and improves schedule viability, while considering operational implications. Located in the state of New Mexico, Chino is one of nine Freeport-McMoRan mining operations in North America. This presentation discusses the benefits of implementing an integrated approach to tactical mine planning, and shares practical examples that were learned as Chino implemented an integrated tactical planning method. This includes improvements in completion time for preparing a schedule, minimal risk from manipulating Excel macros, data integration required to make short-term planning decisions, and better understanding of the mine plan’s effect in relation to the business’s key performance indicators. Ultimately, the integrated approach to tactical mine planning at Chino has led to production forecasts which are more achievable and reduced planning and execution variance. PROJECT OVERVIEW Chino mine is a porphyry copper deposit wholly owned by Freeport-McMoRan, the largest publicly traded copper producer in the world. Chino mine is located in Grant County, New Mexico, a short distance east of Silver City. Ore material mined from the pit today includes oxides, primary sulfides, and secondary sulfides. The mineralized material is sent to a mill, with a rated throughput of 42,000 tons per day, or to ROM leach pads with variable dumping capacities. At Chino, the short-range objective is to maximize total copper pounds sent to the mill, but no fixed cutoff grade accomplishes this for all periods. Instead, 12 different material classifications, including four sulfide classes that can feed either the mill or other destinations, and 38 cutoff bins, are aligned with the needs from operations, leaching, and the concentrator to create a schedule. Cutoffs vary from one week to another to cope with a highly intermittent ore body."

Jan 1, 2018

By P. G. Martin

"As the speed of business has continued to increase over the last decade, the focus on real-time control of the performance of both stationary and mobile assets has become an increasing priority. Traditionally the maintenance team has been focused on the management of the availability of assets while the operations team has been focused on the throughput of those same assets. Typically operations and maintenance teams worked almost independently in spite of the fact that they were both working with the same assets. Part of the problem has been their traditional performance measures which have often been diametrically opposed. Recent advancements in the area of real-time performance measures and decision support have helped to drive higher levels of collaboration between operations and maintenance leading to real-time asset performance control and higher levels of business performance. This paper will explore the forces driving the need for changes, present an effective approach to the definition of the most appropriate business performance measures, and examine the effectiveness of contextualized real-time decision support resulting in asset performance control. TRADITIONAL APPROACHES TO ASSET PERFORMANCE MANAGEMENT In most industrial operations the phrase asset performance management is synonymous with maintenance of the industrial assets. This is the way industry has viewed asset management and asset performance management for decades. This is a very limited perspective that is serving to constrain the profitability of industrial operations. As industrial organizations began to form following the Industrial Revolution, the complexity of the operations forced an organizational design based on specialization. No single person could understand all of the aspects of an industrialized operation. This was particularly true at the plant floor level where the operation and maintenance of the industrial equipment required very different skillsets and training. To accommodate the vast differences most industrial organizations set up operations teams to run the equipment and maintenance teams to keep the equipment available to the operation. Both teams were dealing with the same industrial equipment but from very different perspectives and with very different performance measures. Typically the operations team was measured on maximizing the output of the equipment – or throughput. On the other hand the maintenance team was measured on the uptime – or availability of the equipment."

Jan 1, 2015

By Angela K. Braden

Igneous rock exposures occupy only a minor portion of surface area (<18 mi2) in Arkansas, and are divided into two major groups: nepheline syenite (7 mi2) and syenite complexes (8 mi2), with various dikes and sills representing the remaining surface exposures. The syenite complexes have been the sites of major vanadium and minor titanium production during the past 50 years. Nepheline syenite exposures were important in the early production of locally used building stone; however, aggregate and roofing granules have now become the principal market for the production of nepheline syenite in Arkansas. Nepheline syenite intruded into a sequence of Paleozoic sedimentary rocks in Arkansas and is exposed in two areas: in Saline County near the town of Bauxite, and in Pulaski County at Granite Mountain, just southeast of Little Rock. Although the central Arkansas region had been investigated thoroughly for bauxite by the early 1950s, the nepheline syenite resources of the region have yet to be evaluated systematically by the state. Arkansas nepheline syenite was evaluated for its ceramic uses in 1952. Some recent industry interest has revolved around its potential use as a sand-blast abrasive. The largest exposed areas of nepheline syenite, located at Granite Mountain, currently are being mined by the Minnesota Mining & Manufacturing Company (3M) and McGeorge Contracting (Granite Mountain Quarry). 3M has been in operation since 1947 and mainly produces roofing granules. A fine powder produced by 3M during crushing that is marketed under the name Donnafill? recently has seen use as filler in self-compacting confined construction and as an additive (frit) in common brick. Since the early 1960s, Granite Mountain Quarries has produced a variety of aggregates, ranging from riprap to industrial sand, and recently constructed a computerized hot-mix-asphalt production facility. Approximately 4.5 million tons and 1.2 million tons of syenite were produced from Granite Mountain and 3M, respectively, during 1979. No production values are available after this date; however, combined production from both quarries is estimated to be at least 6 million tons annually.

Jan 1, 1999

By L. Andrews, G. Smits, M. D. Adams, E. A. Viljoen

A new approach has been developed that is capable of ascertaining the ore component that is responsible for the preg­robbing of pregnant pulps. Many gold mines are currently treating ores containing a component that is detrimental to the recovery of gold, in that they "preg-rob" the pregnant pulp by adsorption of some of the dissolved gold. The identity of the preg-robbing component in this type of ore has been the subject of considerable debate over a lengthy period, th various suggestions including amorphous carbon, chlonte, chalcopyrite and layered silicates, such as the phyllosilicate minerals pyrophyllite, kaolinite, phlogopite and illite. A means is now available to identify and characterize the preg-robber in gold ores. This new approach consists of contacting the ore with a synthetic aurocyanide solution, identifying the mineral grains by optical microscopy and analysing each grain individually using high-sensitivity electron microprobe analysis. The approach is exemplified in this initial study by identifying the preg-robbing component in an active sample of gold-bearing shale to be an amorphous carbonaceous phase consisting of discrete particles of about 5 µm diameter interspersed with shale particles and agglomerated into grains of up to 100 µm diameter. Microanalysis of these grains as well as other mineral particles revealed that the gold content of some of the carbonaceous grains was close to 7000 g,lt, with no gold being detected in any of the other mineral phases that were found to be present (e.g. quartz, chlorite, muscovite, pyrophyllite, etc). Bulk analysis of the sample for carbon and gold confirmed that gold loadings of around 7000 g,/t would be expected if all of the gold were adsorbed onto the carbonaceous component. The carbonaceous constituent is probably also responsible for the anomalously high surface area measured for the material. It probably acts in a similar fashion to activated carbon, and the correct choice of organic blinding agent will decrease the extent of preg-robbing by lowering the activity of the material for gold, without causing any downstream problems such as fouling of the activated carbon used for gold recovery

Jan 1, 1993

By Peter Kolitsch, Galyn Rippentrop

INTRODUCTION On April 14, 1994, the joint venture of Kiewit Construction Company and Kenny Construction Company was awarded a 76 million dollar contract for the construction of the New Hampshire Avenue Tunnels in Washington D.C. The Notice to Proceed was given on May16, 1994 and scheduled completion is September 1997. This project is one of five contracts for the Mid-City E Line as part of the Washington Metropolitan Area Transit Authority (WMATA)Greenbelt Route. Once completed, the Mid-City E Line subway tunnels will connect service between the U Street-Cardozo and Fort Totten stations (See Figure 1). The New Hampshire Avenue Tunnels project consists of approximately 6800 feet of twin single track subway tunnels, three vertical shafts, associated utility work and comprehensive restoration work. Section E4b involved two methods of tunneling along the project alignment. The first method consisted of the well known soft ground open face shield driven tunnel and the second method consisted of tunnels driven using the New Austrian Tunneling Method (NATM) . The NATM section of twin tunnels begins at the Buchanan Vent Shaft and proceeds approximately 2630 feet under Rock Creek Cemetery, including the Farragut Emergency Access Shaft and connects approximately 390 feet beyond to the existing Fort Totten running tunnels (See Figure 2). Special considerations had to be given to the portion of the tunnel alignment which passed beneath Rock Creek Cemetery. The analyses and subsequent selection of the tunnel support system were based on anticipated geological conditions and the sensitive tunnel alignment. The New Hampshire Avenue Tunnels project was the second soft ground NATM project in Washington D.C. The first, by no coincidence, was completed at the adjacent Fort Totten Station and Running Tunnels Project by Mergentime/Hochtief, AJV. Currently, on a nearby WMATA jobsite, the J.F. Shea Construction Company has started a third NATM soft ground tunnel. Tunnel support systems were studied with respect to three tunneling methods: •A one-pass system consisting of a bolted precast concrete segmental lining •A two-pass system consisting of an unbolted precast concrete segmen

Jan 1, 1997

By Nelson R. Shaffer

Secondary minerals, amorphous materials, and biologic entities that form on building stone can cause aesthetically unflattering changes in color and may even result in stone decay. Techniques to determine causes of such changes generally have entailed destructive sampling and often required chemical, thin section, X-ray, or other relatively slow, expensive measurements. We have found that a rapid leach of in-place stone using small volumes (50-100 ml) of very pure distilled, deionized water provides recovery of sufficient dissolved material to help diagnose stone anomalies. Water is sprayed onto the stone and collected in a nonwetting plastic pan. Ion chromatograph analysis of waters thus collected from more than 160 sites showed wide variations in concentration of anions F, Cl, NO3, and SO4. Anion analyses were made in minutes for less than $20 per sample. Cations Ca, Mg, Fe, and Sr also were detected, and analyses might be used to determine mineral sources using equilibrium computer models. Solid particles filtered from the samples can be examined microscopically to provide further information about atmospheric agents affecting the stone. The collected water can even be evaporated to precipitate dissolved minerals. Chloride values in samples rinsed from stone ran as high as up to 17,000 ppm, nitrate to 100 ppm, and sulfate to 1,000 ppm. Limited data also indicate that measurable amounts of fluoride were found in some of the rinse waters. Chlorides were most abundant in areas where the stone has become dimpled or spalled. Nitrates were generally higher near ground level, and sulfate tended to be more abundant in samples taken from higher sites or from sheltered sites. Dark-stained limestone tended to yield less soluble material than clean-looking stone. Leachable elements were higher in samples from urban areas. Most of our data are from limestone buildings, but the technique works on other types of dimension stone, man-made construction materials, and even natural outcrops of rocks. Longitudinal studies show that soluble materials vary through time and are affected by climate. This rapid, in situ leach technique, although still being perfected, shows great promise in the diagnosis of stone alteration and in the evaluation of stone treatments because it is completely nondestructive.

Jan 1, 1999

By T. Stuczynski

In the past ten years about 3000 wastewater treatment plants have been built in Poland. The result of this development has been a massive increase in overall sludge production. According to data supplied by the Ministry of Environmental Protection, 400,000 dry tons of sludge are generated every year in Poland (Koblak-Kalinska 1996). Still it is difficult to estimate the amount of sludge, which is used in agriculture or for reclamation purposes. However, it can be assumed that this comes to no more than 10 percent of all sludge produced in Poland on a yearly basis. Thus it became obvious that an urgent solution to this problem was needed. Local authorities in Silesia realized in the early 90?s that a demonstration was necessary to encourage the proper utilization of sludge. This was the basis for establishing the Biosolids Subpart of the Silesia Project, which addressed the use of biosolids in the reclamation of mining and smelting dumps (Stuczynski et al. 1996). Metal waste sites themselves are known to contain more than 87 million tons of waste (Pistelok et al. 1995). Each year this amount increases by approximately 400,000 tons. We realized that a simple solution for stabilizing these sites would be to cover them with vegetation in order to reduce leaching of toxic elements, as well as to keep metallic fugitive dust from entering the environment. The reclamation of smelter waste sites, which was carried out within the framework of the Silesia Project was a joint effort of local government, industry and international research institutions/agencies, including the US Environmental Protection Agency (EPA), the Center for Research and Control of the Environment (OBIKS), Virginia Polytechnic Institute and IUNG. One of the goals was to evaluate the possibility of adapting the rules of sludge management currently used in the United States to conditions commonly found here in industrial regions of Poland. However, the main objective of the Silesia Project was the development of guidelines concerning all aspects of sludge use for the reclamation of degraded lands and waste sites. Biological aspects related to reclamation of metal waste with the use of biosolids will be discussed in this paper.

Jan 1, 2002