Search Documents

By Carl-Eric Dr. Nilsson

Energy cost for mine ventilation in Sweden is high, especially during winter time when air must be heated. This paper presents the result from a project entitled ventilation-as-required. The term ventilation-as-required means that the required volume of fresh air should be distributed only to such areas, where mining work is going on and to be reduced to a minimum in the rest of the mine. Ventilation-as-required is a monitoring system that controls the operation and capacity of the fans and measure the air pollutant gases, i.e. carbon monoxide, nitrogen and sulphur dioxide at strategic points. It is an active system that responds when equipment is under operation. MITU proposed in 1991 a project to develop a ventiation-as¬required system and such components as transmitters and receivers for the communication between the equipment and the fans. The mining companies, Boliden Mineral AB, LKAB, Outokumpu and Ammeberg Mining Corporation joined the project and have financed a joint research and development programme supported with a grant from the Swedish Government through NUTEK. MITU proposed a second project in 1992 to the mining companies to develop an improved "intelligent" fan for scope ventilation. Boliden Mineral and LKAB joined the project and have financed a joint research and development project supported by the Swedish Government through NUTEK. The Government even made a commitment to support the investment of the first 50 fans ordered with a grant of 25% of the investment cost. The result from projects show that the target set up in the plans is more than achieved, with an energy reduction that exceeds 30% compared to previous consumption. No environmental influence due to reduced ventilation is observed in the stope when work is under progress. Dilution of exhaust gases from diesel fuel decreased from 6.000 m3/L consumed diesel fuels to 3,600 m3/L. The automatic data processing and sensor system is even increasing the security of the work so that it can be done under safer environmental conditions.

Jan 1, 1995

By Laura J. Carroll, Gordon A. Goldsmith

Experts, like many of the speakers at the SME Annual Conference, are frequently called upon by lawyers to assist them in litigation. Due to the technical nature of many cases, the testimony of an expert with knowledge and experience in a particular field is necessary to help a judge or jury understand and decide certain issues. Environmental litigation is no exception. Experts routinely are called upon to offer testimony to establish the existence of contamination and its source, as well as the potential health and environmental risks associated with the contaminants. This article will briefly discuss the factors courts apply to determine whether to admit expert testimony after the recent Supreme Court decision in Daubert v. Memell Dow Pharm., Inc., 509 U.S. 579 (1993). The Court's decision in Daubert overruled a long-standing test that had based the admissibility of scientific evidence on its "general acceptance" in the field in issue. Next, the article will discuss in general terms what a party must do to "link a particular defendant's conduct to the contamination involved in order to recover from that defendant. This link, known as causation, varies depending upon the type of claim being asserted. Expert witnesses are used extensively to help establish causation. JUNK SCIENCE OR GOOD SCIENCE- HOW DOES A COURT DETERMINE WHAT TO LET IN A frequent complaint in litigation involving technical or scientific issues is that one party or another is trying to use so-called "junk science" to prove its case. While some expert testimony might be so clearly lacking in support or so "off the wall" that a court can easily determine to exclude it, other testimony, especially testimony on the "cutting edge," is much more problematic. In 1923, the District of Columbia Circuit Court of Appeals decided the case of Frye v. United States, 293 E 1013 (1923). In deciding whether to admit certain expert testimony, the court in Frye stated that while a court will "go a long way in admitting expert testimony deduced from a well-recognized scientific

Jan 1, 1998

By Omar A. Muhtadi

6.1 INTRODUCTION The three most critical factors in successful heap leaching operations are: • The methods employed to pretreat ore (i.e, crushing and agglomeration); • Placement of ore on the leach pad (heap building techniques); and • Wetting of the ore with cyanide (solution application techniques). Improper execution of any of these initial steps may result in a substantial sacrifice of total metal extraction or, in the worst case, in project failure. Ore preparation in terms of crushing and agglomeration was discussed in Chapter 5; this chapter therefore focuses on commonly employed techniques for heap construction and solution application. The main objective of heap construction is to obtain the most homogeneous heap possible. "Channeling" of leachate in heaps with preferential seepage paths leads to preferential leachate distribution and uneven/incomplete extraction. The two main contributing causes of channeling are inadequate attention to heap construction and uneven solution application. These pitfall s can best be avoided through a knowledge of the various techniques available and the applicability and success of these techniques with various ore types and site conditions. The remainder of this chapter provides a discussion on these two subjects. 6.2 HEAP BUILDING TECHNIQUES Successful heap building techniques vary with the type of ore and, since no two orebodies are exactly alike, some slight modifications are usually necessary for each specific project. However, it is possible to generalize in terms of the appropriate techniques to be used with ores having similar characteristics. This section discusses the three most commonly used methods of heap construction and provides some guidelines with regard to ore types, construction constraints, and lift height parameters for each of the three. 6.2.1 Run-of-Mine Dumping and Dozing The run-of-mine method of heap building can only be used with ore of a highly silicious nature (i.e., ore which will not generate a large amount of

Jan 1, 1988

By Michael Robert Hodson

The views expressed in this paper are those of the author and do no necessarily reflect those of CRU. The Extent of Government Involvement In 1982 national governments in the Non-Socialist world owned at least some equity share in an estimated 49 percent of the bauxite mining capacity located in their own countries.* By comparison, as Figure 1 shows, in the same year governments owned at least part of an estimated 33 per cent of primary aluminium smelting capacity. In other industries, national, or state governments in 1982 held at least part ownership of mining capacity in 42 per cent in the copper industry, 34 per cent in the tin industry, 23 per cent of the zinc industry, 15 per cent of the lead industry and 11 per cent in the nickel industry. Thus while within the aluminium industry attention has focussed on the share of government ownership in the primary aluminium sector, national government involvement through ownership is larger in the bauxite sector. Moreover, ownership by government is more widespread in the mining of bauxite than in the mining of all other principal non-ferrous base metals. Yet while the equity participation of governments in the bauxite sector is widespread, it is but one of many forms of government involvement. In addition to direct ownership or equity participation domestic government involvement has taken the form of legislation to protect the environment, controls on the level of production, insistence on the export of ore, pressure to maintain levels of employment, controls on the type of fuel used, foreign exchange *Capacity which is owned in whole or in part is included within the state sector, but capacity in one country which is owned by a wholly or partly owned government company in another company is not included in the state sector; e.g. the capacity of the Trombetas mine is included in the state sector but the capacity of Delphi bauxite would not be included.

Jan 1, 1984

By Weijian Yu, Genshui Wu, Jian Zhang, Yong Ning

Aiming at characteristics of the soft coal roadway engineering geology and deformation, the exposure research of the soft coal seam, theoretical analysis, numerical calculation and program design were carried out. First of all, according to the disclosure, soft coal seam engineering characteristics and geological conditions in Xinxing coal mine were expounded. Meanwhile, the soft coal roadway bolt supporting axial effect, the bolt supporting transverse effect, the anchorage body mechanics strengthening mechanism and problems such as supporting strength have been analyzed. The paper pointed out that the soft coal with very small cohesive force can form a composite anchorage body under the combined action of the anchor cable group, the W-type steel band and the metal net. The soft coal body in the plastic damage area formed anchorage balance arch with a certain bearing capacity and adapted to the rock deformation, and which played an effective support role in the roof outside the balance arch of the roadway. Therefore, the full-cable support technology was proposed. And then, numerical calculation and comparative analysis were conducted on three schemes of the roadway with non-support, with combined support of “anchor bolt and cable” and the full-cable support. The results show that when the roof is supported by anchor cable, it not only controls the continued increase of the subsidence value of the roof, but also effectively suppresses the convergence amount of the floor heave value and the amount on the sidewalls of the roadway. Whether it is from the stress distribution situation, or the viewpoint of plastic zone scope, the combined support of full-cable is more reasonable than that with non-support and that with the combined support of “anchor bolt and cable”. Finally, based on the features of soft coal seam in No.2265 work face of Xinxing coal mine, the relevant support schemes were put forward, and its specific support parameters and cross-section designs were drawn as well.

Jan 1, 2017

By George J. Dvorznak, Robert W. Waytulonis

The Bureau of Mines is conducting a research project in cooperation with the Mine Safety and Health Administration (MSHA). Mining companies, and equipment manufacturers are also participating through the Colorado Mining Association (CMA). The objectives of this cooperative research project are to determine the practicality of coupling a dry exhaust conditioning system (dry system) and diesel particulate filter (DPF) to make an integrated control system, and to determine the effectiveness and durability of the integrated system in an underground coal mine. Diesel-powered mining machines must be equipped with control devices to reduce surface and exhaust temperatures to safe levels and prevent flames and sparks from being emitted to the mine atmosphere. Diesel exhaust-gas water scrubbers have been successfully used for many years but they have several disadvantages; they are large, consume large quantities of water, and require frequent maintenance to remain functional. Additionally, diesel exhaust is a source of noxious gases and particulate matter. Particulate emissions are composed primarily of small carbon particles with absorbed hydrocarbons and they are almost entirely respirable in size. Even an engine in good mechanical condition can emit up to 400 mg/cu m of respirable particulate matter. A dry system for control of diesel fire and explosion hazards, coupled to a DPF, promises to be a complete control system for diesel engines. The dry system cools the exhaust and suppresses sparks and flame with a heat exchanger and flame and spark traps. The conditioner is smaller, consumes no water, and requires less maintenance than a comparable water scrubber. The DPF uses a ceramic substrate as a wall-flow filter and is very efficient at collecting exhaust particles. Average particulate mass collection efficiency is 90%. This report describes a cooperative research project to combine the dry system with the DPF, conduct performance tests on the integrated system at Bureau and MSHA 1aboratory facilities, and conduct field tests of the system on a production machine in an underground coal mine.

Jan 1, 1987

By V. Castranova, L. Wu, K. Van Dyke, J. Gutierrez, V. Vallayathan

Since it has been demonstrated that silica caused phagocytic cells to activate lipoxygenase metabolism of unsaturated fatty acids we thought selective inhibition of this metabolic pathway might be helpful in treatment of silicosis. It is known that lipoxygenase metabolism plays a role in the pathogenesis of a variety of inflammatory and hypersensitivity conditions. Further, it is believed that the alveolar phagocytic cells which engulf silica begin the inflammatory cycle which produces the metabolic products, cytokines and growth factors which causes fibrosis in the lung. There have been indications that drugs which inhibit lipoxygenase can inhibit fibrosis from other causes. Previously, we developed a method which detects the activity of lipoxygenase metabolism by measuring free radical oxidation via light production or chemiluminescence (CL). We decided to apply this method to phagocytic cells that would be found in the lung in the presence of silica with and without newly developed inhibitors of the lipoxygenase reaction. We used drugs which inhibit lipoxygenase directly including AA861 (TAKEDA), A63162 (Abbott), and an inhibitor that scavenges free radicals produced from the lipoxygenase reaction, nordihydroguairetic acid. In addition we used an indirect inhibitor, tetrandrine. We found drug inhibition of silica activated CL from alveolar macrophages, neutrophils and human leukemia (HL-60) cells differentiated with DMSO. Nordihydroguairetic acid 2x10-5M produced almost complete inhibition in all three cell types. In human leukemia cells (HL-60) A63162 and tetrandrine were equally inhibitory at 42% while in human neutrophils A63162 and tetrandrine were less active 22 and 10% respectively. In macrophages A63162 and AA861 were less than 50% inhibitory to cellular CL at 2xl0-5M. Direct assay of tetrandrine (2x10-5M) with sodium arachidonate and soybean lipoxygenase reveals no inhibition. All antilipoxygenase drugs regardless of mechanism were inhibitory to cellular chemiluminescence from all three types of phagocytic cells. These drugs alone or in mixtures could prove useful in treatment of silicosis.

Jan 1, 1991

By T. M. Karppanen

Shotcrete is used both in mining and tunnelling for supporting rock. Both dry and wet processes are used for shotcreting, and each produces good quality concrete. Thick shotcrete layers function as a concrete arch supporting loose rock. Thin layers prevent relative movements between the blocks of rock due to the fine concrete in the cracks and joints. No progressive fallouts occur since key blocks are kept in place. Rockbolts are often used together with shotcrete in order to create an arch around the tunnel making the rock to support itself. Shotcrete is sprayed either manually or by means of mechanized equipment. The aim is to spray required the layer thickness in one pass and with a minimum amount of rebound. Sprayed layers should also be as even as possible. The tip of the nozzle should be moved in circular movements. The shotcrete should be sprayed at a right angle to the rock surface; the optimum distance from the nozzle to the application surface must be found by experiment. In a mine shotcreting forms a materials handling system which includes batching, transporting and the actual shotcreting. The equipment used vary depending on the spraying method, mining conditions and the location of the mine. Shotcreting is performed with a purpose-designed unit in most cases where operation is mechanized. The shotcreting unit consists of a spraying machine with a hose and a nozzle, an additive system, a manipulator and a mobile carrier with all the necessary controls and accessories. The key element of the unit is the shotcreting manipulator which holds and guides the nozzle as required. The manipulators currently in use are hydraulically operated, and their remote controlled booms are also often called robots. These manipulators have enabled users to increase their output capacities, to remove the operator away from unsafe areas and from the influence of dust and rebound. Furthermore, they improve the shotcrete quality and reduce shotcreting costs.

Jan 1, 1989

By W. H. Pailes, V. Castranova, K. Van Dyke, J. H. Kang

Recruitment and activation of phagocytic cells after inhalation of occupational dusts has been implicated in the development of pulmonary inflammation, fibrosis, or emphysema. Plateletactivating factor has been described recently as a potent inflammatory agent. The objective of the present study was to investigate if platelet-activating factor might play a role in the inflammatory response of the lung to occupational dusts. In vitro exposure of alveolar macrophages to cotton dust (4 mg/ml), silica (10 mg/ml), or coal dust (10 mg/ml) results in the release of picomole levels of platelet-activating factor with a potency of cotton dust > silica > coal dust. Time course studies indicate that platelet-activating factor release from alveolar macrophages is maximal approximately 10 minutes after in vitro exposure to silica. In vitro, platelet-activating factor is a direct stimulant of polymorphonuclear leukocytes increasing chemiluminescence 2.3 ± 0.3 fold above control. The maximal response occurs in the dose range of 10-10 to 10-7M platelet activating factor. In addition, plateletactivating factor potentiates the response of polymorphonuclear leukocytes to a second stimulant; i.e., chemiluminescence generated from polymorphonuclear leukocytes exposed to plateletactivating factor (10-9M) plus chemotactic peptide (FMLP, 10-9M) is 88 ± 22% greater than the sum of the separate effects of these stimulants. In contrast, platelet-activating factor is not a direct stimulant of alveolar macrophages in vitro, having no stimulatory effect on chemiluminescence or superoxide anion release even at levels of 10-6 to 10-5M platelet-activating factor. However, platelet-activating factor (10-5M) does potentiate zymosan-stimulated activation of chemiluminescence and superoxide release from alveolar macrophages by 117 ± 56% and 30 ± 4%, respectively. In conclusion, these data indicate that exposure of the lung to occupational dusts results in the release of platelet-activating factor which may activate polymorphonuclear leukocytes and potentiate the responsiveness of alveolar macrophages to dust. The net result would be pulmonary inflammation and hypersecretion of reactive species by pulmonary phagocytes which could lead to tissue damage and pulmonary disease.

Jan 1, 1991

By Wolfgang Pietsch

Roller presses were first invented in the middle of the 19th century, for the economical size enlargement of coal fines as fuels. Coal briquettes became quickly accepted for industrial and domestic use giving rise to a large and sucessful industry, particularly in Europe, Japan, and North America. When, towards the middle of the 20th century, coal was more and more replaced by other energy sources, such as electricity, gas, and oil, roller press manufacturers searched for alternate applications of this equipment. In addition to contemporary coal briquetting, in fields such as smokeless fuel and form-coke, it was found that redesigned and modernized roller presses, which are now capable of exerting high forces, are versatile machines for many tasks in mineral processing. Today they are used for: - the "classic" pressure agglomeration and - the "new" high pressure comminution. In pressure agglomeration, the characteristics of fine minerals are improved by forming briquettes or granulated products from compacts. During size enlargement with roller presses briquettes are directly obtained while granular materials are produced by crushing and sizing of compacted sheets. The processes are carried-out essentially dry and often do not require binders other than those inherently contained in the feed and "activated" by the high forces and/or elevated feed temperatures (e.g. hot briquetting). Therefore, no foreign materials (impurities) are added. Another advantage of the technology is, that wide particle size distributions are acceptable or desirable as feed materials, including millimeter or even centimeter sized particles. Plastic particles deform and brittle materials are crushed during pressure agglomeration. A relatively new application of roller presses in mineral processing is the utilization of the crushing effect when brittle materials pass the nip area between the rollers. It was found that this crushing mechanism is very efficient thus saving energy, particularly in grinding circuits handling large capacities. The paper introduces the fundamentals of the process and describes the design as well as applications of modern roller presses in mineral processing.

Jan 1, 1995

By Barnaby J. Watten, Sibrell. Philip L., Brian J. Vinci, Andrew E. Friedrich

We evaluated a new process for remediation of acid rock drainage (ARD). The process treats ARD with intermittently fluidized beds of granular limestone maintained within a continuous flow reactor pressurized with CO2. Tests were performed over a thirty day period at the Toby Creek mine drainage treatment plant, Elk County, Pennsylvania in cooperation with the Pennsylvania Department of Environmental Protection. Equipment performance was established at operating pressures of 0,34,82, and 117 kPa using an ARD flow of 227 L/min. The ARD had the following characteristics: pH, 3.1; temperature, 10 OC; dissolved oxygen, 6.4 mg/L; acidity, 260 mg/5; total iron, 21 mg/L; aluminum, 22 mg/L; manganese, 7.5 mg/L; and conductivity, 1400 uS/cm. In all cases tested, processed ARD was net alkaline with mean pH and alkalinities of 6.7 and 59 mg/L at a CO2 pressure of 0 kPa, 6.6 and 158 mg/L at 34 kPa, 7.4 and 240 mg/L at 82 kPa, and 7.4 and 290 mg/L at 117 kPa Processed ARD alkalinities were correlated to the settled bed depth (p<0.001) and CO2 pressure (p<0.001). Iron, aluminum, and manganese removal efficiencies of 96%, 99%, and 5%, respectively, were achieved with filtration following treatment. No indications of metal hydroxide precipitation or armoring of the limestone were observed. The surplus alkalinity established at 82 kPa was successful in treating an equivalent of 1136 L/min (fivefold dilution) of the combined three ARD streams entering the Toby Creek Plant. This side-stream capability provides savings in treatment unit scale as well as flexibility in treatment effect. The capability of the system to handle higher influent acidity was tested by elevating the acidity to 5000 mg/L with sulfuric acid. Net alkaline effluent was produced, indicating applicability of the process to highly acidic ARD.

Jan 1, 2000

By Stefan Lorenz, Robert Galler

"The technical lifetime of underground structures does not only depend on the long-term behavior of individual support elements and material characteristics, but also on various boundary conditions, which influence the entire long-term system behavior of the structure. Thanks to the construction of second tunnel tubes and the corresponding cross passages sampling of support materials such as shotcrete, concrete of the inner lining and rock bolts including sheet membranes is possible. To evaluate the stresses and the supporting effects of the tunnel shells, flat-jack tests and different simulations were performed. With these simulations the percentage of the load bearing behavior of the shotcrete shell can be determined. From the results, conclusions for new design approaches for tunnel construction should be generated. New concepts, in which the outer lining is part of the permanent support elements can be considered. This approach would be applicable for conventional as well as mechanical tunneling. INTRODUCTION Tunnels are an indispensable part of modern transport infrastructure. As multi-generation structures their long-term preservation as well as their technical service life is of central importance. The current state of research in the field of durability of structural elements must be considered separately. In almost all areas a prediction of materials and structural components towards lifetime exists. System-wide investigations were rarely performed, so that there is no technical lifetime consideration of the outer lining in systems included. In this study the mechanical behavior of the interface connection in a double shell lining (DSL) tunnel was investigated in laboratory tests. Objective The target of this work is, at first, to create a large database with the lifetime of different structural elements and materials, which may be the basis of durability considerations of tunnels. Secondly, the goal of these investigations is to optimize tunnel designs and their dimensioning regarding to the technical lifetime. For that matter, it is necessary to analyze the selected approaches of the loss of strength and stiffness of the outer lining."

Jan 1, 2016

By S. G. Vick, K. E. Robinson, W. D. Webb

INTRODUCTION This paper discusses two uranium tailings waste disposal studies that reflect the United States Nuclear Regulatory Commission (NRC) regulatory actions and their changing requirements during the mid to late 1970&apos;s. Present guidelines require that all new uranium tailings impoundments be designed and constructed to eliminate, to the extent that it is reasonably achievable, exposures and risks to the public from the tailings. This includes positive measures for control of seepage losses from the impoundment and for control of radiological releases caused by wind and water erosion. Long-term stability of the reclaimed impoundment is also a very important requirement. That is, it is intended that the tailings impoundment, once it is reclaimed, will require little or no care or maintenance as long as the uranium tailings remain a hazard. Principally because of the long-term stability objective, the NRC has now identified subsurface burial of the tailings as the "prime option" for tailings disposal. The environmental implications of these proposed regulatory actions are obviously desirable. The economic implications the actions may have on a particular project are not always so obvious because they are so dependent on environmental suitability of site conditions. Selection of a site with favorable topographic, geologic and hydrologic conditions will usually result in the most economically and environmentally attractive alternative for tailings disposal. The first project discussed in this paper was initiated before the NRC guidelines had been developed to favour subsurface burial. At the beginning, seepage and radon emission control requirements were moderate. Constraints were imposed on the design by site topography, geology, and project capitalization considerations, factors which were dealt with according to straightforward engineering and design principles. More serious constraints were imposed by changing regulatory requirements. Unlike the more usual engineeringrelated constraints, regulatory requirements were upgraded during the design process, causing the design itself to undergo numerous modifications. The second project was initiated after the NRC proposed regulations had become better defined and below grade burial appeared to be the preferred

Jan 1, 1980

By Jianmin Qin, Raja V. Ramani, Wilson Miola

The number of underground work entities operating under reduced dust standards in U.S. coal mines has been increasing since the start of the decade of the 80s and is currently approaching 10,000. The concern for controlling the quartz levels in airborne respirable dust in coal mine has manifested itself in several improvements in equipment selection and operation, face ventilation practices, and dust control procedures. At the same time, fundamental studies have been initiated on determining the source-sink relationships of the airborne quartz dust. The P-7 method is the prescribed method for the determination of quartz in the respirable airborne dust samples from coal mines. Questions have been raised on the reliability of the P-7 infrared spectrometry method for quartz analysis in powders. No specific method has been defined for quartz determination in bulk samples from the mine. In a recent study on the relationship between quartz in the airborne dust and that in the materials being mined, both infrared (IR) and x-ray diffraction (XRD) methods were used on a suite of samples from several coal mines. These samples encompassed airborne respirable dust samples, airborne total dust samples, the oversize fraction from the respirable samplers, ROM samples, channel samples, and chip samples from the face, roof, and floor materials. In this paper, the sample preparation and analysis procedures for the samples are discussed. The data, analysis results, and comparisons of the P-7 and XRD results are presented. The quartz percent determined for the same sample by the two methods are different. In 85% of the samples analyzed, the quartz percents determined by the XRD method are higher than those obtained by the P-7 method. However, there is a strong linear relationship between the results from the two methods. Further, the XRD method indicates an average of 20 percent more quartz than that from the P-7 method. The reasons for the differences in the results and the need for additional studies are explored.

Jan 1, 1991

By Dennis Dolinar

Improperly designed support systems have led to unplanned roof falls in longwall tailgates. To prevent such falls requires appropriate support and adequately designed support systems. The National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. To design the support system with this methodology requires a quantitative assessment of the ground and support interaction, which is developed from instrumented test sites installed in longwall tailgates. To compliment and expand the field data results and to optimize the support design, numerical modeling is also conducted. The models are calibrated from the test site data. In the present study, data was obtained from a longwall tailgate in the Illinois basin. The test site was located in the Herrin No. 6 coal seam at a depth of 500 ft. At the site, the immediate roof was a weak shale overlain by a competent limestone. Above the limestone, sandstone formed the intermediate roof. The floor consisted of a weak underclay. In the study, the performance and interaction with the surrounding rock mass of two different standing supports, an engineered crib and a conventional 4-point wood crib were monitored. The two cribs have similar load-displacement characteristics at least through 6 in of displacement. Beyond 6 in, the engineered crib becomes unstable and begins to strain soften and shed load. The measurements and developed ground reaction curves indicated that the tailgate at the mine was a low convergence environment until well inby the face. Because the convergence was well below their capacity, both supports provide more than adequate levels of support to the tailgate. Significant convergence and support loading did not occur until 90 to 100 ft inby the face. The results of this study were also compared with results from similar studies conducted in the Pittsburgh seam to further advance the development of the ?ground reaction curve? based support system design.

Jan 1, 2009

By Robert L. Randall

The mineral industries have a continuing need for market forecasting and analysis for a variety of purposes, among which are organization and control of the sales effort, financial and corporate planning, and evaluation of the anticipated revenue from investment in proposed projects. For anything beyond the simplest extrapolation, some kind of economic reasoning or analysis is called for, which may or may not be incorporated into a formal or quantitative model. The principles described here apply to most of the commercially significant minerals and metals. The examples are drawn largely from the copper market, as it is the one with which I have the most practical experience. Practical forecasting is the process of analysis and synthesis from three categories of knowledge: facts and statistics, theory, and practical knowledge and informed opinion. Although many attempts have been made to build forecasts on only one of these three pillars, none has been successful as an operating procedure because of the lack of balance. There are no facts about the future-only about the present and the past. Facts can illuminate the future, but the future can be described only in terms of probability or more or less likely states of affairs-not as a continuous extension of the past and present. Likewise, theory, although useful as an organizing discipline and for providing a methodology of analysis, is inadequate for the complexities of reality. This is especially so when there is feedback between plans and forecasts to produce a new outcome and when there are significant elements of unpredictable free will, such as presidential jawboning or foreign policy considerations. Such elements are difficult to accommodate in neat theories, although they must certainly be reflected in the forecasts. Pure opinion frequently suffers from both a lack of-disciplined reasoning and the presence of biases or self-interest. While the future is unknown, it tends to cast its shadow before it; hence, forecasting is the art and science of positioning oneself so that the shadow becomes visible to the forecaster.

Jan 1, 1979

By Henryk Bystron

The underground fire areas are formed as a result of failure of an active fire extinguishing in mines. Such areas bring about a fire hazard for the work safety and for the mining operations. For liquidation of fire areas it is necessary to create conditions under which a possibly small amount of air is flowing to the fire. To achieve this end, isolation methods are used which consist in erection of full stoppings of various types, sealing practically the fire areas. These methods usually fail in oases when the coal seam is thick and the fire area is situated between the intake shaft and the outtake shaft in which a high-pressure fan is in operation. In such oases ventilation methods based on the balance of aerodynamic potentials in fire areas are to be used. For a very long time the isolation and ventilation methods have been developed in the world mining, No sooner than since 1980 the aerodynamic potential has been used in ventilation methods [1,2,6]. So far, the aerodynamic potential was called in different ways and was determined by different formulae which gave its numerical values more or less approximative. Nevertheless, even in situations featuring by a lack of sufficient theoretical bases of the aerodynamic potential the ventilation methods brought considerable profits in the field of safety in mines and of economics in mine ventilation [1-6,9,10]. The increase in the depth of underground mines and their equipment with expensive machines (apparatus) brought about that the Central Mining Institute at Katowice undertook research works which are crowned by the theory of the aerodynamic potential in mine ventilation networks [7]. The use of this theory in the mentioned ventilation methods will increase their effectiveness. Since the theory will be published in the III rd quarter of this year, we cite in the present paper the formulae and relations associated with this theory which are indispensable to present the balance of aerodynamic potentials in the fire areas in their control by ventilation methods.

Jan 1, 1980

By Ted D. Johnson

INTRODUCTION The tailing dam is part of the SOHIO L-Bar Uranium Mine and Mill located about 70.8 kilometers (44 miles) west of Albuquerque in northwestern New Mexico. The dam location is shown on Figure 1. The tailing dam is one of the last upstream method dams permitted in the industry. Design and construction aspects of the project, as well as operation and maintenance considerations, are reviewed herein. Since initial construction, SOHIO Western Mining Company and Woodward-Clyde Consultants have developed several modifications and improvements in the dam&apos;s operating and monitoring procedures. This work has been done in coordination with the New Mexico State Engineer&apos;s Office and in accordance with recommendations in a report done for the Corps of Engineer&apos;s Phase I Dam Inspection Report. Modifications and improvements described should be of particular interest to owners and operators of other tailing dams utilizing the upstream method of deposition. The tailing facility was designed for a 10-year life to provide an ultimate storage capacity of 6 1/2 billion kilograms (7 1/2 million short tons) in an area of about 180 acres. A plan view of the tailing dam is shown on Figure 2. The tailing consists of approximately 75% sand size material and 25% fines (material passing the No. 200 sieve). The tailing dam includes a small earth starter dam with raises of the dam accomplished using tailing deposited by upstream method techniques. The starter dam is a homogeneous embankment about 610 meters (2000 feet) long, a maximum height of 12 meters (40 feet) and 2 1/2:1 (horizontal to vertical) upstream and downstream slopes. The starter dam contains an internal drainage system which includes a near vertical chimney drain connected to horizontal finger drains. A typical section through the maximum height of the starter dam is shown on Figure 3. A small confining dam, approximately 1.6 meters (5 feet) high, is constructed beyond the limits

Jan 1, 1980

By S. Henley

There is much in common between the requirements of open-pit mining and quarrying operations. Both involve the extraction of large volumes of material from surface excavations. The principal differences are of degree: open-pit mining of materials such as coal or gold generally involves the extraction of only small volumes of &apos;mineral&apos; and large volumes of waste-they are operations with very high stripping ratios, and are made viable only because of the high unit value of the extracted mineral. In quarrying operations, the unit value of the mineral - sand, aggregate, limestone, or clay - is much lower, but stripping ration Are also lower. Thus the same techniques of geological modelling, reserve estimation, and pit planning are applicable, as is shown in two examples from the British quarrying industry. In each case, a primary requirement is the definition of production volume or tonnage. Sometimes, this need may be addressed simply by the use of a survey data processing package. However, in other cases, such as the two examples addressed in this paper, of sand and clay quarries, detailed assessment of the variation of mineral grades is a vital part of the exercise, and simple volumetric modelling cannot in itself be sufficient. In these cases, a block model approach using simple logical and numerical post-processing is also required to obtain required parameters for commercial classification of the products to be extracted. Pit designs themselves may be optimised by use of algorithms such as Lerchs-Grossmann, but the value of mineral produced can be dependent on factors other than its grade in any one part of a single pit, and the &apos;optimised&apos; pit itself must be considered only a good sub-optimal. Given the right degree of healthy skepticism, and a software package with sufficient flexibility to be adapted readily to the rather different requirements of the quarrying industry, there is no reason why the quarrying industry should not benefit from the many years of investment in mining software technology.

Jan 1, 1989

By Jerome C. Motz

Los tipos, tamaños y número de trituradores empleados en un sistema completo de reducción varían con factores tales como: el volumen de mineral que debe ser procesado, tamaño de la mina, tamaño máximo del todo-uno, dureza del mineral y de su roca soporte y tamano requerido para el producto final. Básicamente, sólo existen tres tipos distintos de equipos de trituración para la etapa primaria. Estos son: machacadoras de mandíbulas, trituradores giratorios y molinos de impactos, y cada uno tiene unas características operativas propias. Las trituradoras de mandíbulas operan por aplastamiento de las rocas entre dos paredes, una fija y otra móvil, en una cavidad determinada. Han sido ensayadas variaciones en la caída y movimiento, pero la mayoría de las máquinas del tipo Blake tienen un ángulo de trituración de aproximadamente 27° entre las mandíbulas fijas y móviles. El principio de trabajo del triturador giratorio es muy simple. Si un cono es montado en un eje vertical y la parte superior del eje se sitúa estacionaria mientras que la parte inferior gira excéntricamente, el cono tendrá también un movimiento excéntrico. Si el cono se coloca en una carcasa conveniente se movers aproximándose y retrocediendo de las paredes que lo contienen a la vez que gira. Si el cono y las paredes de la carcasa son suficientemente robustas y pesadas, cualquier cosa apresada entre ellas será triturada. Al lado de los incrementos de la eficacia desarrollados por las continuas acciones de trituración y el curvado de las caras de trituración, los trituradores del tipo giratorio tienen las siguientes ventajas: 1. La gran abertura de alimentación disponibles en comparación con trituradores de otro tipo. 2. El alto rango de tamaños y capacidades, que se encuentran entre 600 y 6.000 toneladas por hora. 3. Generalmente no es necesario control en la alimentación. Dumpers de 150 a 200 toneladas descargan directamente en las actuales instalaciones.

Jan 1, 1982