Search Documents

By Robert H. Carpenter

Abstract, Syngenetic uranium in pre metamorphic Idaho Springs volcanics and sediments probably, was mobilized during metamorphism (1.7 b.y.) and partly retained along unconformities. Precambrian Silver Plume intrusives (1.4 b.y.) and Pikes Peak granite (1.0 b.y.) may have mobilized uranium from the craton and. Idaho Springs metamorphics to concentrate it in cauldron sites in migmatites, pegmatites, alaskite, disseminations and greissen. Tertiary intrusives also may have upgraded uranium by anatexis, leaching and differentiation. Tertiary vein and shear zone uranium mineralization may have-been-derived from underlying magma sources, leached from Idaho Springs metamorphics and from syngenetic leaching of overlying sediments and introduced by deep hydrothermal convection systems.

Jan 1, 1979

By M. Szatkowski

The studies conducted by Laplante and coworkers (1983,1984) with flotation of galena and quartz, showed that the rate of flotation reaches a maximum value for a certain intermediate value of the air flow rate. A similar, though less pronounced, effect of the air flow rate on the selectivity was also observed. Luttrell and coworkers (1985) showed that the size of air bubbles has a significant effect on both rate and selectivity of coal flotation. These two studies used flotation tests in which no froth layer was formed. This note describes effects of the air flow rate and bubble size on the rate constant and selectivity of coal flotation, using a mechanical laboratory machine with a froth layer allowed to form. Experimental A raw, dry ground Illinois coal was used in flotation tests. The size distribution and ash content of the samples are : Particle size (µm) Weight (%) Ash (%) +600 4.30 41.7 600/200 43.05 19.0 200/74 22.25 16.0 - 74 30.40 24.0 average 20.8 No. 2 fuel oil with a concentration of 200 g/t of feed and M.IBC with concentrations of 11, 22, and 33 mg/L of pulp (128, 256, 384 g/t, respectively) were used as flotation reagents. Tap water with a natural pH of 7.0 to 7.8 was used throughout the tests. No other reagents were used. The starting concentration of coal in the pulp was 86 g/L. A standard flotation machine with the pulp volume of 5 L was used in experiments. Three different air flow rates were employed, resulting in three air escape velocity values of 14, 30, and 70 cm/min. The air escape velocity (AEV) was calculated as the ratio of air flow rate (Qa) to the slurry surface (Ss) in the machine. For a comparison, the upper limit of air escape velocity values used in commercial size flotation machines is between 70 and 100 cm/min (WEMCO, 1983). A machine consisting of a generator of fine bubbles and a separatory column, described elsewhere (Szatkowski and Freyberger, 1985), was used for some tests where bubble size lower than that generated in the standard machines was required. Prior to a flotation test, a batch of coal was mixed with water in the flotation cell for at least 10 minutes to ensure that all coal was thoroughly wet. Then the specified amount of fuel oil was added and the pulp was conditioned for five minutes. The specified amount of MIBC was added 15 seconds before the end of conditioning. After air flow was opened, flotation products were collected for 0 to 30, 30 to 60, and 60 to 120 second intervals. Content of the combustible material in samples was determined by subtracting the ash content from 100%. A photographic technique was used to determine initial distributions of bubble size generated by the flotation machines. Bubbles generated in water containing the prescribed amount of the frother but no solids were photographed against a black background. The average diameter and standard deviation were then calculated for each set of flotation conditions. The method gives results reproducible within k 5% of the average bubble size. Table 1 contains information about the measured bubble size distributions expressed by the average bubble diameter (Db) and the standard deviation ( SD ) . Results and discussion The general formula for calculating the flotation selectivity is: o = recovery of coal/recovery of ash (1)

Jan 1, 1988

By S. A. Saki, J. F. Brune

"INTRODUCTION Longwall coal mining leaves large areas where the coal has been made removed and the roof rock strata collapse, forming a zone of broken rock rubble called the gob. Figure 1 shows a typical longwall gob area along with the gate roads. The ventilation pattern for progressively sealed longwall panels follows a simple “U” pattern where fresh air is coursed inby to the headgate, flows along the face and exhausts through the outby tailgate as shown in figure 1(a). An important variation of this pattern is the back return (BR) arrangement where the exhaust air from the face is drawn inby and around the nearest open cross cut before it turns in the outby direction towards the exhaust fan. Figure 1(b) illustrates the use of back return. This arrangement moves the point of low pressure from the tailgate corner up to 60 m inby and thus maintains fresh air in the tailgate region that could otherwise be contaminated with gob air.The gob area may contain remnants of unmined coal or parts of overlying coal beds that continue to release methane, eventually filling the gob area with methane in concentrations far above the explosive range of about 4.5 to 15%. Many gob areas must be equipped with gob ventilation boreholes (GVBs) to extract methane, and GVBs often exhaust methane at concentrations from 50% to 90% (Saki, 2016). Due to oxidation processes occurring in the gob, the oxygen content is reduced to a low level, with nitrogen and CO2 making up the major remaining components of the gob atmosphere. FORMATION OF EXPLOSIVE GAS ZONES IN GOBS Since the longwall face area is ventilated with fresh air below 1% methane and the face and gob areas are not separated, an explosive fringe will form where the methane content lies within the explosive range and oxygen content remains above 12%. Figure 2 shows a typical development of such an EGZ. This figure is based on a computational fluid dynamics (CFD) model developed by CSM researchers to analyze gas concentrations and flow patterns in longwall mining. Figure 2(a) shows the formation of EGZ in the gob with a U type ventilation scheme, where EGZ lies right behind the shields in the tailgate corner. Figure 2(b) shows the formation of EGZ in the gob combining U type ventilation scheme with BR, where EGZ is pushed away from the face deep into the gob. The CFD modeling parameters and boundary conditions have been verified with field data from two cooperating, active longwall mines (see Worrall 2012, Marts 2015, Gilmore 2015 and Saki 2016). Other mine geometries, methane inflow rates and gob permeability distributions can be modeled to establish representative gob atmospheric conditions. Two GVBs were operating in the model, extracting 0.165 m3/sec each. The methane in the working areas and returns was kept below 1%. Methane flowing into the model from a rider coal bed above the mined seam was at the rate of 0.55 m3/sec."

Jan 1, 2017

By R. D. Williams

"In a very real sense, Butte, MT is where the copper came from that won two world wars. The price for that unrestricted mining and smelting of copper came due in 1983 when Butte was declared a Superfund site.One of the most complex remnants of this mining history is the Parrot Tailings site. The Parrot smelter operated from 1881 to 1910, moving Upper Silver Bow Creek to the south and depositing approximately 283,000 m3 (370,000 cu yd) of waste material adjacent to Upper Silver Bow Creek. Additional mixed waste from other processing sites deposited below the Parrot tailings at the Northside Tailings, Diggings East and Blacktail Creek Berm total approximately 171,000 m3 (224,000 cu yd) of contaminated material. As part of the Superfund remedy, the U.S. Environmental Protection Agency (EPA) proposed leaving all these wastes in place. This proposal prompted a detailed criticism by several geoscientists familiar with the site. The EPA’s 2006 Record of Decision (ROD) did in fact leave these wastes in place, which set the stage for a series of studies that continue to refine how best to protect extensive completed Superfund Remediation downstream of Upper Silver Bow Creek. History of the Parrott Mine and tailingsPlacer gold was discovered in Silver Bow Creek, the headwaters of the Clark Fork River only a few miles from the Continental Divide in 1864. This discovery led to a stampede of placer and lode claims. One of the first lode claims located was the Parrot lode, located in the fall of 1864. Progress for developing a mine at the Parrott was slow, and it was not until 1876 that one of the original locators encountered a rich vein of chalcocite. Butte had its first copper mine.The Parrott Mine was patented in 1879 and by 1881 the Parrot, having lost a “t”, concentrator and smelter were built. The smelter and concentrator were an immediate success with a considerable market for processing the district’s rich copper ore. In 1885, the employees of the Parrot smelter bought the Butte Reduction Works, another smelter. In 1885, dams were built on Silver Bow Creek to contain various tailings and related processing byproducts (Fig. 1).By 1890, the various smelters in Butte rendered Butte’s air quality as suffocating (Fig. 2). An 1889 funeral procession was rumored to have gotten lost in the thick smelter smoke and somehow ended up at the Centennial Brewery. A city ordinance was passed late in 1890 in an attempt to control smoke. The Parrot smelter employed approximately 500 men by 1890. Through the 1890s, the tailings produced grew from approximately 91 t/d (100 stpd) to more than 181 t/d (200 stpd). Copper values in the tailings were initially as high as 4 percent, but as the processing improved that was reduced to 1.5 percent."

Apr 1, 2019

By Brendan Howard

Rio Tinto has a large globally distributed technical workforce and needs to ensure these employees have the requisite skills to not only manage technical risk and enable safe efficient production, but also ensure they are keeping pace with a fast-changing technological landscape. Traditional approaches to learning struggle for scale and an inability to respond to the extreme diversity of capability development needs. In response, Rio Tinto has successfully introduced innovative approaches to learning and employee engagement via leveraging the power of globally distributed networks for peer-to-peer knowledge transfer and providing mechanisms to recognise, reward and retain the individual technical contributors.

Feb 1, 2024

By Yang Song, Li Shaokang, Wang Zhiqiang, Wang Jinjun, Li Guofeng, Su Meixuan

The paper investigates the triboelectric charging properties of calcium carbonate (CaCO3) particles under different conditions using a cyclone tribocharger. It explores the effects of airflow velocity, tribocharge material, and particle moving distance on the charge-to-mass ratio of CaCO3 particles. The study aims to provide guidance for the design of triboelectric separation systems for magnesite.

Sep 1, 2023

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimal when the concentrations of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/liquid ratio of 67 g/L, stirring speed of 400 rpm and leaching duration of 60 min. Under these conditions, 90.49 percent and 6.78 percent of Mn and Fe were dissolved, respectively, from the ore sample in a size fraction of smaller than 106 µm. It was determined that the leaching of manganese from the ores was a second-order reaction with activation energy, Ea, of 53.38 kJ/mol. The leaching residues obtained under the optimal conditions were subjected to wet high-intensity magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20 percent Fe and 1.79 percent Mn with iron and manganese recoveries of 56.83 and 66.73 percent, respectively. To the best of our knowledge, this is the first time that a magnetic separation process was used on a residue obtained from the reductive acid leaching of manganiferous iron ores to recover iron.

By A. Martikainen, S. GYAMFI

Luossavaara-Kiirunavaara Aktiebolag’s (LKAB) Konsuln iron ore mine, located just south of the famous Kiruna iron ore mine in Malmfälten in northern Sweden inside the Arctic Circle, was developed as a test mine between 2018 and 2020 for the Sustainable Underground Mining (SUM) project [1]. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 Mtpa using conventional diesel machines. The design was created by Kiruna mine ventilation team, Stina Klemo and Joakim Jonasson, in cooperation with a consultant, Tomas Bolsöy from EOL Vent Mining AB. There is a plan to increase this rate to between 1.8 and 3 Mtpa in the future, and this requires the primary fans to be upgraded. Therefore, a study was carried out to determine whether using ventilation on demand (VOD) could avoid this fan upgrade and reduce Konsuln’s ventilation and heating power costs in the future. The study also investigated whether using battery electric vehicles (BEVs) along with VOD or as a standalone strategy could further reduce these power costs. In addition, the study analyzed the suitability of heating power reduction strategies presently or previously used in Nordic countries and Canada to investigate potential additional strategies to reduce heating power cost, the largest portion of Konsuln’s ventilation and heating power costs.

By Mike Ghassemi

It is clear that precise overground and under-ground mapping is an important factor for all designers. Due to rapid changes in underground construction, tunnel designers are increasingly in need of updating project information. This article explains the latest techniques for detecting under-ground utilities as well as underground mapping. Global Positioning System (GPS) is a very ac-curate and popular navigation and mapping system that has been used extensively above ground, but is not used for underground mapping as signals are not strong enough to pass through ground or water. Most underground techniques were developed for military applications during the first and second world wars. Later, the techniques became public. For example, ground penetrating radar was developed for the military in 1970 to be used for locating tunnels under the demilitarized zone between North and South Korea. Later, the same technique was used for detecting unexploded ordinance such as plastic land mines.

Jan 1, 2011

By T. Weatherwax, A. Rai, J. Poor

"This paper provides an overview of the current use of auxiliary ventilation products and the challenges with limited air quantity in dead-end entry or working faces. The PVC’s low frictional factor, low physical constraint and minimum leakage properties were ideal to develop as ventilation duct in conjunction with the concept of ""Made in the US and Used in the US"". The PVC duct supports the operational and total cost of ownership with on-going success. This paper will discuss the continuous improvement made in ventilation ancillary products for optimum results. The paper will also cover mine site usage of second generation PVC vent duct underground and the results from the operational and technical side making a difference in health and safety and overall auxiliary ventilation. INTRODUCTION The Barrick Turquoise Ridge Inc. (TR) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestone, siltstones, and mudstones. The weak nature of the ground facilitates the need for underhand cut and fills mining methods.Mining Method; Underhand cut and fill: The mine uses underhand cut and fill method which has 12’x12’ and or 14’x14’ top cuts with several different size undercuts. The ore body is accessed off of a secondary tertiary heading, utilizing a heading with a cross section of 14W x 14H or 15W x 15H configuration. In the wider and more massive zones, two headings in a production panel may be worked at any one time. Drift round lengths are determined by the ground conditions and drift dimension. An example of a typical topcut and associated undercut layout is shown in Figure 2."

Jan 1, 2016

By Roger Storry, Donald Bruce, Arnaud Hochart

"INTRODUCTIONThe Port of Miami Tunnel (POMT), designed and constructed by Bouygues Civil Works Florida between 2009 and 2014, was a Public Private Partnership between the Miami Access Tunnel Concessionaire, Florida Department of Transport, Miami-Dade County and the City of Miami. The project comprises dual 11.3m internal diameter, 1.27km long, twin lane road tunnels running between Watson and Dodge islands and under the main shipping channel in Biscayne Bay (Figure 1).The POMT was a unique project which embodied many technical firsts and involved the first large diameter tunnels constructed through Florida’s challenging sedimentary carbonate strata. At the outset, a comprehensive ground investigation was performed, using both conventional and less conventional investigation techniques, to characterise the highly heterogeneous ground conditions.The findings of the investigation had a major impact on the tunnelling methods, triggering a series of mitigation works to ensure that the tunnels could be excavated safely and effectively. The mitigations included modifications to the already designed Tunnel Boring Machine (TBM), to facilitate an innovative excavation process, and a unique grouting campaign (Storry et. al. 2013a). The project was completed and opened to traffic in August, 2014 and has significantly alleviated traffic congestion in Downtown Miami.GEOLOGICAL CONTEXTThe geological conditions at the project site consist of carbonate sediments which can be divided into distinct geologic units; the Miami Limestone Formation (Layers S3, S4), the Fort Thompson Formation (Layer S5), the Anastasia Formation (Layer S6), the Key Largo Formation (Layer S7) and the Tamiami Formation (Layer S8). Multiple changes in sea level over a relatively short geologic time scale have resulted in a heterogeneous profile consisting of interbedded sedimentary rocks and sediments, which vary widely, both vertically and laterally (Figure 2)."

Jan 1, 2016

By Ralph M. Barnett

It is no longer a question of "If" mining operations will meet standards and regulations set by various governing bodies and the demands of citizen groups. Legislation is fact. The needs of citizens are becoming more of a integral part of mining company planning. "Open Planning", regardless of some frustrations it provides, is working. Climax, AMAX Chemical and AMAX Exploration are successfully employing several citizen involvement techniques in exploration and feasibility study phases of planning for potential new mines.

Jan 1, 1978

By M. T. Ityokumbul

The effect of reaction conditions on the desulphurization of oil sand coke residues has been studied. The variables investigated were temperature, reaction time, heat transfer resistance, and mode of caustic soda addition. The results obtained show that oil sand coke desulphurization increases with temperature, reaction time, and heat transfer rate. In an oxidative environment, coke combustion during molten caustic leaching (MCL) commences at temperatures above 500°C. The mode of caustic addition has no effect on coke desulphurization.

Jan 1, 1995

By Adrian E. Scheidegger

Recently, a new theory of the subsidence of rock masses has been advanced by Litwiniszyn and coworkers, which is based on the notion that the individual rock particles perform random walks. It is shown in the present paper that the final equations of the random walk theory can be justified from general principles of statistical mechanics in which no specific theoretical model of particle behavior has to be made. The theory appears to account appropriately for subsidence phenomena.

Jan 1, 1966

By X. Wu

A quantitative damage evaluation caused by ground motions associated with strong roof caving is presented. The strong roofs are modeled as either cantilevering or bridging beams over continuous elastic foundations subject to an exponentially distributed vertical stress. Major factors influencing roof caveability and strain energy buildup are identified and investigated. A methodology to evaluate the strain energy accumulation caused by overhanging roof is presented. The potential for mine tremors is determined in terms of the local Richter magnitude ML which depends on the seismic energy transformed from the stored strain energy released when the roof fails. A particle velocity model is applied to estimate the damage area associated with roof collapse. A case study from a Utah coal mine shows that estimations of bump severity and damage area agree well with the field observations.

Jan 1, 1995

By P. T. Bissert, L. Yan, M. D. Klein

"Federal regulations require the installation of refuge alternatives (RAs) in underground coal mines. Mobile RAs have a limited ability to dissipate heat, and heat buildup can lead to a life-threatening condition as the RA internal air temperature and relative humidity increase. The National Institute for Occupational Safety and Health Office of Mine Safety and Health Research performed heat testing on a 10-person tent-type training RA and contracted ThermoAnalytics, Inc. to develop a validated thermal simulation model (TSM) of the tested RA. The TSM was used to examine the effects of the constant mine strata temperature assumption, initial mine air temperature (MAT), initial mine strata surface temperature (MSST), initial mine strata temperature at depth (MSTD), and mine strata thermal behavior on RA internal air temperature using 117 W of sensible heat input per simulated miner. For the studied RA, when the mine strata temperature was treated as a constant, the final predicted RA internal air temperature was 12.8°F lower than it was when the mine strata thermal behavior was included in the model. A 10°F increase in the initial MSST resulted in a 7.1°F increase in the final RA internal air temperature, whereas a 10°F increase in the initial MSTD yielded a 2.5°F increase in the final RA internal air temperature. INTRODUCTION Since 2008, the Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines (1). MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. NIOSH recommended an apparent temperature limit of 95°F in its 2007 report to Congress (2). In 30 CFR 7.504, MSHA has specified a maximum apparent temperature of 95°F inside an occupied RA (3). The apparent temperature is calculated using both air temperature and relative humidity (4). Calculations could be used to determine if the air within an occupied RA will reach the apparent temperature limit. In these calculations, in order to simplify the problem, the mine temperature could be assumed to remain constant. With this assumption, the effects of the mine strata thermal mass and thermal conductivity on the heat buildup in an RA are ignored. OMSHR research has shown that the mine air and strata temperatures surrounding an RA increase when subjected to the heat of an occupied RA (5). Thus, calculations performed with the assumption that the mine temperature is constant would under-predict the resulting dry-bulb temperature and apparent temperature for a given RA occupancy. The mine air temperature has been used as the basis for RA temperature calculations. However, research has not been used to confirm that the mine air temperature is the appropriate basis."

Jan 1, 2016

By M. Poulton, J. A. Botín, C. Gatica

"The Chilean minerals industry faces a shortage of 27.000 new skilled professional by 2023. Enhancing the integration of women into the workforce is a possible solution. This study analyzes the state of women in the mining workforce over the past decade. Several key indicators are presented: percent in the workforce, salaries, career profiles, presence at management level, and participation in academia are studied. The study also analyzes the strategies used by government, industry, and universities to recruit and retain women for the minerals industry. The main results show that women represent 7.4% of the mining workforce in Chile and less than 1% of senior positions with a salary gap of approximately 30%. Systematically, women prefer professional programs in geology, chemistry, and environmental areas. The Chilean statistics are compared to data from the United States mining industry. INTRODUCTION The Chilean mining industry faces a significant shortage of professionals for the next decade which compromises competitiveness and productivity. The demand for human capital in mining depends on several factors. First, the age structure of workforce, which determines future retirement needs. Second, minerals market considerations, determining the amount and size of mining projects entering production in the coming years. Third, the evolution, positive or negative, of productivity, mainly driven by technology and innovation, and negatively affected by the declining ore grades. Finally, negative trends in lead times to production of mining projects, due to social opposition, changing regulations and other project contingencies, negatively affecting the demand for human capital. Regarding the supply of human capital, the fast increase in the technology level of the minerals industry and hence, the increase of technical qualification requirements of the human capital generates a rise in the time required for trade and university education of mining professionals, which may cause imbalances in the labor market. According to (Consejo Minero, 2014) human capital gap in Chile by 2023 will be around 27.000 workers for extractive, processing and maintenance jobs, which represents 14% of the current workforce (Figure 1)."

Jan 1, 2016

By A. K. Fallaw, D. L. Taylor, G. Wang, L. R. Moore, S. Dobson, C. B. Parkinson

"Over the years, the decline of high grade ores have become an increasing problem in the global mining industry. As such, techniques and chemistries must change in order to continue to meet the market demand and quality. Reverse cationic flotation of quartz and silicates is one of the most important techniques for generating the industry standard product from minerals such as iron and phosphate ores. Amine collectors are the global standard in such processes. However, as the ore quality continues to decline so must the chemistry change to meet the change in ore composition. This paper will focus on the introduction and full scale application of a novel amine collector towards a cleaner flotation process in phosphate beneficiation with Crago process. The results suggests the collector is capable of improving the phosphate recovery, in this cleaner circuit, to approximately 94% with minimal sensitivity to the everyday changes in feed grade.INTRODUCTION The days of mining high grade minerals are long gone, but the demand continues to increase. Phosphate ore, for example, is most dominantly demanded from the agriculture industry as a fertilizer component (i.e. diammonium phosphate, DAP) (FAO, 2014). Some literature suggests that global food production must increase by approximately 70% by 2050 (Cordell, 2009). It is also suggested that the peak global phosphorus production will occur around the year 2033, which is the period at which the easily accessible reserves have been depleted. Currently, phosphorus is commonly mined with a BPL (Bone Phosphate of Lime) concentration of 12-20% and a remainder typically being gangue minerals such as silica, clays, metal oxides, calcareous minerals, and carbonaceous minerals. These gangue components can lead to various negative processing and utilization consequences. Calcium, from carbonaceous minerals, is problematic due to the elevated levels of sulfuric acid required to convert the phosphate rock to the acid form (SRI Consulting, 2009). Calcium can also lead to elevated dosages of flotation reagents due to the desire of the fatty acid to coordinate to calcium minerals. Carbonate leads to increased levels of foam during the wet acid process. Silica is associated with the level of insols (acid insolubles), which must be less than 10% in the final concentrate that will be transferred to the chemical plant for acidification. Phosphate ore can generally be classified as carbonaceous or siliceous (El-Shall, 2003). Siliceous ores are commonly processed through various sizing steps followed by multi-staged flotation (Figure 1) (FIPR, 2014 & Güven, 2010). Though the higher grade phosphate pebble is declining, many mines are still able to size good enough to produce some amount of such pebble. Unlike most metal flotation processes where grinding is a necessity for an optimal process, Florida phosphate flotation does not generally require aggressive grinding and can typically operate at 0.1-1.0 mm. The rougher flotation step applies pH modification to achieve the optimal pH of 8.8-9.3 followed by conditioning with a fatty acid type collector, which builds a hydrophobic waxy layer on the surface of the particle to assist in the flotation. This generally achieves higher than 85% recovery of a product with 50-60% BPL and 15-30% insols. Unfortunately, DAP production generally requires 3.5 tons of phosphate rock containing greater than 63% BPL to produce 1 ton of phosphoric acid (ArgusMedia, 2014). Thus, further purification is required to achieve the grade by the chemical plant for fertilizer production. After the fatty acid is scrubbed off the phosphate particles using sulfuric acid (pH 2.5-3.5), the pH is generally operationally readjusted to 6.5-7.2 by washing with “fresh” water. A second collector is applied prior to the cleaner, which is a reverse cationic flotation process. This collector is typically a cationic amine based reagent, which should have an affinity for silica containing mineral"

Jan 1, 2015

By G. Jeffrey Taylor

The environment at the lunar surface is drastically different from the one we are used to on Earth. The Moon has one-sixth of Earth's gravity, virtually no atmosphere, a surface bathed in radiation and micrometeorites, large temperature gradients, low seismicity, and a dusty, rubbly surface. To successfully mine and process materials on the Moon and to mitigate degradation effects in the hostile lunar environment, these factors require new designs for equipment and development of new techniques and technologies.

Jan 1, 1990

By K. L. Kasperski, M. T. Ityokumbul

The effect of reaction conditions on the desulfurization of oil-sand coke residues was studied. The variables investigated were temperature, reaction time, heat transfer resistance and mode of caustic soda addition. The results show that oil-sand coke desulfurization increases with temperature, reaction time and heat-transfer rate. In an oxidative environment, coke combustion during molten-caustic leaching (MCL) commences at temperatures above 500 °C. The mode of caustic addition has no effect on coke desulfurization.

Jan 1, 1996