Search Documents

By Raj K. Rajamani, Samira Rashidi

Wear is an extremely important topic when considering high-pressure grinding rolls (HPGR) for any new application. Given the inevitable variations in ore properties throughout a mine’s life, it is difficult to predict the effect of material and operating conditions on the wear parts: specifically, the HPGR rolls. However, the possibility of continuous scanning of rolls provides ample information to review the wear pattern and ways to optimize it. In this regard, as part of a broader investigation, the feasibility of in-line scanning of HPGR rolls in a laboratory-scale HPGR is studied and presented. The choice of scanners and methods adopted to achieve high-level accuracy for determining wear is discussed in this paper, and the inherent variability affecting the measurements is evaluated. 

By Wedam Nyaaba, Edward Wellman, Angelina Anani, Eduardo Cordova, Sefiu O, Cluber Rojas, Adewuyi

This study aims to investigate the optimal method for ore pass construction in incompetent rock masses. We evaluated the conventional and raise boring methods based on safety, efficiency, excavation control and ground support for ore pass construction. A stability analysis using analytical Q-raise (QR method) and kinematic analysis methods for ore pass construction with a raise borer before and after grout injection of the rock mass was performed. As a case study, an ore pass (diameter of 3 m, depth of 100 m) within an incompetent rock mass was considered to gain further insight. The rock mass was characterized according to the classification methods Q Barton, rock quality designation (RQD), rock mass rating (RMR) and geological strength index (GSI). The grout intensity number (GIN) method of grout injection was used. The safety factor of less than 1.075 obtained before injection was lower than the acceptance criteria. However, grout injection before raise borer excavation resulted in a safety factor greater than 1.5. Using a raise borer without pre-grouting indicated that the maximum unsupported diameter (MUSD) of the ore pass was less than the required 3 m and equal to or larger than 3 m post-grouting.

Dec 1, 2024

By Byron R. Berger

Epithermal Ag-Au deposits form at low to moderate temperatures in near-surface environments. Historically, these deposits have been the source of high-grade ores. Increases in the market prices for gold and silver make lower-grade ores economically viable when available in large tonnages. Both the high-grade and bulk-tonnage ores are a consequence of the same processes, and general models of epithermal systems can be useful in the search for new precious-metal resources. A detailed study of deposits at Round Mountain, Nevada; Balei, Russia; Creede, Colorado; Guanajuato, Mexico; and Chanarcillo, Chile, indicates that the hydrodynamics of the fluid systems as determined by fracture geometries, the permeability, and composition of the host rocks are the key factors in the creation of both high-grade and bulk-tonnage epithermal deposits. End-member models that explain the range of observed deposit characteristics are: (1) the hot-springs deposition model; (2) the stacked-cell convection model (where mineral deposition occurs laterally along the interface of two partially separated fluid reservoirs); and, (3) the closed-cell convection model (where deposition occurs in vertical zones due to the relatively unimpeded vertical flow of hydrothermal fluids). Boiling and fluid mixing appear to be agents of precious-metal deposition with the self-sealing of the hydrothermal system being an important adjunct to boiling. Imaginative application of model concepts in exploration has led and can lead to the discovery of new high-grade and/or bulk-tonnage precious-metal deposits.

Jan 1, 1982

Evver since it first displayed an autonomous mining truck at the 1996 MinExpo show in Las Vegas, NV, Caterpillar has been building the blocks to a fully autonomous mine. In May, the company unveiled another block in that progression, the new Cat MineStar System that it says is ?the industry?s broadest, most comprehensively integrated miner operations and mobile equipment management system.? The full system is comprised of five capability sets ? Fleet, Terrain, Detect, Health and Command ? to help operators define the size and scope of their management system based on the needs of their mining operations. Michael Murphy, technology and autonomy manager for Cat Global Mining, explained that the customers were not ready for an autonomous mining truck in 1996, but that many customers wanted the building blocks to eventually get to autonomous mining. After 15 years of work, Murphy said the building blocks have come together in the form of the Cat MineStar System.

Jan 1, 2011

By L. Gutierrez, J. S. Castro S. Laskowski

Water is a medium in which flotation takes place, and flotation efficiency is highly dependent on water quality. Of the total water resources on Earth, less than 2.5 percent is fresh water. This water is used in agriculture, by households and by industry. Among the industrial users of fresh water, the mining industry occupies an important position. Furthermore, mining operations are often located in arid areas with very limited access to fresh water. The demand for and shortage of water in these parts of the world, such as the Atacama Desert in Chile, makes the use of seawater by the mining industry the only sustainable solution. 

By Barbara J. Arnold

Combat Infantrymen’s Badge and Bronze Star Medal. Following his discharge from the Army, he re-entered SDSM&T in 1946 and earned a B.S. degree in Metallurgical Engineering in 1948. He then received an M.S. from Montana Tech (MT), worked several years in industry and then as an Assistant Professor at the University of Washington (Seattle). He joined his Montana Tech colleague, Douglas W. Fuerstenau, at The Massachusetts Institute of Technology (MIT), receiving his doctorate in 1957. While at MIT, he married Clare M. Donaghue of Dorchester, Massachusetts, in 1955

Jan 3, 2022

By Zengwu Zhao, Peng Xu, Jieliang Wang, Qingwei Bai, Xinyang Liu, Xiao Lei

The paper investigates the capture and recovery of rare earth minerals from Bayan Obo ore using superconducting magnetic separation. A finite element model (FEM) was established to study the influence of various factors on the capture of rare earth minerals under a high-gradient superconducting magnetic field. The study aims to improve the efficiency of rare earth mineral separation and recovery.

Oct 1, 2023

By Ihsan Berk Tulu, Haochen Zhao, Deniz Tuncay

The process of designing pillars and selecting support measures in underground coal mines relies highly on the accurate assessment of mining-induced loads and the load-bearing capacities of the supports. This study proposes a new method to estimate the percentage of load carried by the gob in underground coal mines using a new parameter that introduces the site-specific overburden geology.

Jun 1, 2023

By BHAMIDIPATI S. SASTRY, KATTAMURI PAVAN KUMAR, ADITYA PANDEY

Several laboratory methods are available to determine the thermal conductivity of rocks, but most of them are complex and cumbersome. The present study explains the working principle of Lee’s apparatus, which is relatively simple, easy to fabricate and use, and provides consistent results. In the present study, thermal conductivities of sandstone cores obtained from an Indian coal mine are determined using Lee’s apparatus. An approach is discussed to determine the temperature gradient of sandstone specimens while cooling and is used to calculate thermal conductivity. The thermal conductivities of different sandstone specimens have values between 2.37 and 2.59 Wm−1°C−1. For different sandstone cores obtained from the field, properties including specific gravity, specific heat capacity, thermal diffusivity and porosity, along with thermal conductivity, were determined and highlighted in this study.

By Mahmut Altiner

Magnesium is listed as a key critical raw material in a report by the European Commission that evaluated raw materials based on supply risk versus economic importance [1]. It has extraordinary properties, such as nontoxicity, inertness, high melting point, stability, low weight, chemical resistance, electrical insulation, optical transparency, corrosion-resistant behavior and refractory nature. It is widely used in the areas of agriculture; the environment, for antibacterial and water-purification purposes; electronics; automotive; drug delivery; ceramics; construction, as filler in brick; and concrete production, in the forms of magnesium oxychloride and magnesium oxysulfate. Magnesium oxide (MgO) particles can be produced through the calcination of magnesite ore at different calcination conditions depending on the desired quality of the product, classified as fused (2,800 °C), dead-burned (>1,400 °C), hard-burned (1,000–1,400 °C), or light-burned MgO (700–1,000 °C) [2]. However, the global availability of magnesite ore is limited.

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence events induced by underground longwall coal-mining operations can cause various disturbances to surface structures, ranging from integrity and stability to functionality problems. Highway bridges, as a kind of special road construction that can only tolerate smaller movements and deformations than road pavements, are particularly susceptible to severe influence caused by subsidence-induced ground movements and deformations. However, based on accurate subsidence prediction and correct influence assessments, efficient and effective mitigation and remediation measures can be designed and implemented to ensure the continuous service of bridges, safety of travelers, and smooth mining operations. In this paper, based on the predicted final and dynamic surface movements and deformations, the techniques to assess subsidence influence on the integrity, stability and functionality of bridge structures (such as decks, beams and abutments) are presented. A number of mitigation measures to protect bridge structures are recommended, along with an actual application case.

By William Gleason

"What will the mine of the future look like? Will it resemble the current operations that supply the world with the products it needs to function, or will it be something totally different? How will the demands from the communities that are most affected by mining operations shape the mine of the future? How will technology and innovation be used to help miners reach deposits that are getting harder to access, and what are the dangers of this new world? Who will work at the mine of the future, and what will that work look like?These are questions that do not yet have definitive answers, but they are questions that need to be asked for the mining industry to move into a future that is as filled with uncertainty and challenge as it is with promise and opportunity.On Feb. 16, the 2015 SME Annual Conference and Expo and the 117th CMA National Western Mining Association conference began with a keynote address, "The mine of the future: Forecasting opportunities and challenges for the global mining industry." Panelists from five sectors of the mining industry participated in the session, which was followed by the conference and expo, that in large part, were also trying to answer the question of what the mine of the future will look like.In coming months, Mining Engineering will continue the discussions and answer some of the questions submitted by members of the 2,000-person audience during the keynote address in a monthly feature called, "Predicting the Mine of the Future," and in Thought Leaders Podcasts with the panelists and other industry experts."

Jan 1, 2014

By T. Faulkner, S. A. Richards

"The Scale-Distance formula is one of the primary means of determining the maximum amount of explosives that can be safely detonated at one time by a single delay. This paper describes a method of applying the Scale-Distance formula to the entire mining area using gridded surfaces. Using this technique, the operator can better determine the economic impact of nearby structures on the mine plan. INTRODUCTION As the surface mining of coal and stone encroaches near populated areas, precautions must be taken to minimize blast vibration damage to protected structures. The common method employed to minimize vibration damage is not to reduce the total amount of explosive in the hole (which would negatively affect fragmentation), but rather to introduce delays to reduce the amount of explosive detonated at any point in time. The Scale-Distance formula, an industry-accepted standard, may be used to calculate the maximum weight of explosive that can be detonated at one time without damaging the structure. This information may then be used to determine the number of delays required for each hole. Detonators make up a large part of the cost of blasting. At roughly $15 per detonator an additional detonator in the hole can be significant. It is normal to set off hundreds of holes at in one shot. An additional detonator in each hole can cost additional thousands of dollars per shot. The number of detonators is also a function of the depth of the holes and the hole spacing. Being able to accurately forecast the economic impact of blasting near structures improves a company’s ability to make informed decisions on how to approach property owners. Operators basically have three options when dealing with property owners: 1. Buy the property and blast without restriction 2. Negotiate with property owner for a waiver to allow unrestricted blasting 3. Comply with the legal blasting restrictions This paper proposes a method for the engineer to forecast for all points in the proposed mining area the impact of nearby structures upon the blast design. Being able to create a contour map and ultimately estimate the number of delays required for the entire forecasted mining area, the engineer can create accurate economic forecasts of the cost of blasting. The objective is to reduce the level of uncertainty in the forecast of the blast component portion of the forecast."

Jan 1, 2016

By William Gleason

"Ed Rapp is among those who believe in the saying that necessity is the mother of all invention. Rapp is the president of Caterpillar’s mining group. As such, he is tasked with leading the world’s largest mining equipment maker, and its customers, through this time of lower commodity prices, while also positioning his company to be prepared for better days that lie ahead.The decade-long mining boom fueled by growth in emerging markets and demand for commodities that led to record prices for some metals paused in 2008 with the global financial crisis. However, according to Rapp, thanks to stimulus packages around the world, and in particular the stimulus from China that was focused on infrastructure, the mining sector recovered fairly quickly, and from 2010 to 2012, mining was strong.And then the stimulus stopped. Credit dried up and global growth began to slow down and, in the three years since, commodity prices have declined by an average of 60 percent. Caterpillar expanded during the boom, acquiring Bucyrus, and investing billions into the mining sector. It has felt the pinch of the slowdown as much as any mining company in the world. These pages, and those of other mining publications as well as mainstream media, have been filled with stories of doom and gloom about the industry. But Rapp, while acknowledging that the difficult times have been painful, also said Caterpillar sees opportunity in the slow down and reaffirmed his company’s commitment to the mining industry as absolute."

Jan 1, 2014

Peru has become an established mining country. The industry and industry-related businesses account for a significant amount of the country´s revenue, on state and local levels. But like other countries with thriving mining industries, Peru has seen its mining industry revenues fall off in recent years due to a lackluster global economy. And the mining industry in Peru must also deal with increasing concerns about mining?s environmental impacts, local community and other social issues, as well as a regulatory environment that has placed more restrictions on what miners can do. That said, the Peruvian government is beginning to realize how important mining and natural resource development is to building the nation?s economy, improving its infrastructure and lifting its population out of poverty. The government support was evident during the Perumin 2013 mining convention, held in September in Arequipa. In addition to Peru?s President Ollanta Humala speaking at the closing ceremony, the country?s ministers of Energy and Mines, and Economy and Finance participated in the event, as well as numerous other federal and state authorities. Perumin is put on by the Instituto de Ingenieros de Minas del Peru (IIMP, or Peruvian Institute of Mine Engineers). The 31st edition of the convention, billed as the ?world?s largest mining convention? by the IIMP, this event was led by Abraham Chahuan CEO of Antamina and Romulo Mucho (SME member) as president of IIMP, attracted about 118,000 participants from more than 48 countries. This was more than the anticipated 75,000 attendance and well past the 51,000 people who attended the 2011 convention. The last edition of PERUMIN was led by the CEO of Compañía Minera Antamina, Abraham Chahuan and Rómulo Mucho (SME member) and representative of the IIMP. The event attracted more than 1,000 journalists from all over the world, the IIMP said. A total of 2,213 booths from equipment and machinery supplying companies from the five continents were present at the Mining Technology Exhibition (Extemin), including companies from the United States, Canada, China, South Africa, Germany, Australia, Brazil and Chile, among others. The convention has grown so large in recent years, that the IIMP shifted its location from Tecsup vocational school in Arequipa to the Cerro Juli Convention Center. The venue is 116 percent larger than Tecsup, the IIMP reported, covering about 20 ha (40 acres). It was reported by Latinomineria magazine that about 10 million Peruvian soles were invested in the new venue to create a world-class events center. It was also estimated that the event generated more than 234 million soles to Arequipa?s economy.

Feb 1, 2014

By Yuting Xue, Lihong Zhou, DAVOOD BAHRAMI

The paper discusses the use of machine learning (ML) to develop a predictive model for determining the location and size of underground mine fires using simulated ventilation data. The study highlights the importance of prompt fire location determination for effective firefighting strategies and reducing injury risks. The ML model was trained with simulated data and achieved an accuracy score of 0.920, which improved to 0.962 by grouping closely connected airways.

Sep 1, 2023

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering and display technologies have generated increased accessibility to virtual reality. Virtual reality allows for the creation of dynamic, high-fidelity environments to simulate dangerous situations and test conditions and to visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, U.S. National Institute for Occupational Safety and Health (NIOSH) researchers developed a virtual-reality framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization and training. This paper describes the features of VR Mine, including mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

By MATTHEW HART, THOMAS BAMFORD, Kamran Esmaeili, MICHAL KOWALCZYK, FILIP MEDINAC

Improved haul-road conditions can have a positive impact on mine operations, resulting in heightened safety, productivity gains, longer tire life and lower maintenance costs. For these reasons, a monitoring program is required to ensure the operational efficiency of the haul roads. Currently, at Bald Mountain Mine, monthly site severity studies, ad hoc inspections by frontline supervisors or operator feedback reporting are used to assess road conditions. These methods are subjective and provide low temporal resolution data. This case study presents novel unmanned aerial vehicle (UAV) technologies, applied on a critical section of haul road at Bald Mountain, to showcase the potential for monitoring haul roads. The results show that orthophotos and digital elevation models can be used to assess the road smoothness condition and to check the road design compliance. Moreover, the aerial mapping allows detection of surface water, rock spillage and potholes on the road that can be quickly repaired/removed by the dedicated road maintenance team.

By S. D. F. Rocha, A. L. A. SANTOS, E. M. A. BECHELENI, F. P. C. Silvas

Hydrometallurgical processes are needed to extract nickel (Ni) when it is disseminated in mineral matrix. High-pressure acid leaching (HPAL) and atmospheric acid leaching (AAL) are alternatives, and AAL has the advantage of requiring mild temperatures and pressure. Reducing-reagent tests improved the extraction of metals for the specific limiting portion of the ore. Low dosage of sodium thiosulfate presented better selectivity and safer operating conditions, allowing metal extractions of 50–62 percent at 95 °C. However, the low extraction rate obtained for Ni and the similar levels of impurities — magnesium (Mg), manganese (Mn), cobalt (Co) and iron (Fe) — extracted may represent economical and technological challenges in the downstream process.

By ETHAN FUSTER, STEPHEN LEE, Richard Ray

By offering savings in space and capital cost compared to ducted axial and centrifugal fan systems, horizontally mounted jet fans are commonly used worldwide to ventilate vehicular tunnels. They discharge high-velocity jets to transfer momentum to the surrounding airstream to induce longitudinal flow in the same direction as the jet. Vertically mounted jet fans installed in exhaust shafts have been successfully used to ventilate a large passenger rail overbuild in New York City. A comparison of shaft dimensions, vertical placement of the jet fans and measured shaft airflows is presented to evaluate optimum jet fan configurations. Measured shaft airflows are compared to airflows predicted by computational fluid dynamics (CFD) simulations of a three-dimensional model of the overbuild.

Sep 1, 2022