Search Documents

In this paper, the logic and the capabilities of a long term production planning method for open pit mining are presented. The method is the first attempt in obtaining simultaneous solutions to the four interrelated parameters of open pit mining; 1) the mine life, 2) the specific blocks to be mined each year, 3) the amount of ore and waste to be mined each year, and 4) the ultimate pit limits. An efficient cutoff grade can also be obtained through a sensitivity analysis. None of the existing methods can bring such a comprehensive solution to the problem. A production plan for a real life gold deposit is given to illustrate the logic and the capabilities of the method.

Jan 1, 1993

By P. R. Thomas

This paper addresses the relative long-term cost and resource position of new and existing ferrochromium production in selected Market Economy Countries (MEC'S). The market impact of new ferrochromium production in nations such as India and the Philippines and the continuing change in international trading patterns are also evaluated. This paper draws upon the data and analyses of a recent Bureau of Mines, Department of Interior, Minerals Availability Program appraisal that evaluated the cost and availability of chromite and ferrochromium production from the demonstrated resources of 80 producing or potential mining operations in 10 market economy countries.

Jan 1, 1984

By D. J. A. Chambers, J. M. Wempen, K. D. Koper, M. K. McCarter, K. L. Pankow

"The EarthScope Transportable Array (TA) of broadband seismometers (www.usarray.org) was deployed across southwest Wyoming from November 2007 through May 2009. During this time period the Array Network Facility (ANF, anf.ucsd.edu) detected and located a total of six seismic events near the trona-mining district. This lack of seismicity is atypical compared to coal mines employing similar mining methods. In this study, eighteen months of continuous seismic data from several nearby TA stations are reexamined using conventional and correlation-based methods to detect seismic events. Waveform cluster analysis and epicentral locations are used to discriminate between mining induced seismicity (MIS) and seismic energy generated from surface blasts at nearby coal mines. The locations and magnitudes of the 143 newly detected MIS events are compared to regional subsidence as measured by Differential Interferometric Synthetic Aperture Radar (DInSAR). INTRODUCTION An abundance of natural resources and a favorable political climate have made southwest Wyoming home to multiple large mining operations. Among these operations are five underground trona mines located approximately 50 km west of Rock Springs, Wyoming. The trona mines employ room and pillar, longwall, and solution mining methods over an area roughly 900 km2, and produce a sizable portion of the world’s soda ash (Brown 1995). Historically, in the Rock Springs mining district, several relatively large magnitude seismic events have occurred. These events are thought to have been related to mining activity and have caused notable subsidence (Case 1997). The largest event in the region recorded by seismometers, ML 5.1, has been confirmed as the 1995 Solvay Trona Mine collapse (Pechmann et al. 1995). In addition, blasting at surface coal mines near Rock Springs produces significant amounts of seismicity; approximately 50% of all daytime seismic events in the Mountain time zone from 2007 to 2009 locate near an active surface mine in this region (Astiz et al. 2014). Much of the current research related to surface subsidence and induced seismicity focuses on wastewater impoundment (Ellsworth 2013) and hydraulic fracturing. The observable seismicity in geological injection environments is widely variable and McGarr (2014) has argued that, in such environments, the maximum amount of seismic energy that can be released is proportional to the injected volumes. Like injection environments, in extraction (mining) environments seismicity is highly variable depending on many geological and operational variables (Boltz et al. 2012; Carnec and Delacourt 2000; Fritschen 2010; Iannacchione et al. 2005; Sen 2013) and does not always correlate well spatially with subsidence, a surface expression of extraction at depth."

Jan 1, 2015

By Robert H. Carpenter

Abstract, Syngenetic uranium in pre metamorphic Idaho Springs volcanics and sediments probably, was mobilized during metamorphism (1.7 b.y.) and partly retained along unconformities. Precambrian Silver Plume intrusives (1.4 b.y.) and Pikes Peak granite (1.0 b.y.) may have mobilized uranium from the craton and. Idaho Springs metamorphics to concentrate it in cauldron sites in migmatites, pegmatites, alaskite, disseminations and greissen. Tertiary intrusives also may have upgraded uranium by anatexis, leaching and differentiation. Tertiary vein and shear zone uranium mineralization may have-been-derived from underlying magma sources, leached from Idaho Springs metamorphics and from syngenetic leaching of overlying sediments and introduced by deep hydrothermal convection systems.

Jan 1, 1979

By Robert Klug, Nils Engelke

"In order to extract proportionately small quantities of valuable minerals, mining companies move large amounts of earth. A resulting waste product of this process has traditionally been stored in a semi-liquid phase known as tailings, typically stored in a large pond created by an earthen dam at the low end of a drainage basin. It is generally expected that these dams are stable enough to withstand the pressure of the stored material. Unfortunately, history shows us that this is not always the case. The Baia Mare dam in Romania failed in 2000, causing tragic and prolonged environmental damage to several major European rivers. The Bento Rodrigues dam in Brazil failed on Nov. 5, 2015, and that event resulted in the loss of 16 lives.In hard rock mining, many minerals are imbedded within the ore. As part of the mining process, valuable minerals are extracted from the ore; often, the mineral content is only a fraction of the total ore volume processed. To extract the minerals, the ore is typically crushed and pulverized into very fine particles, then wetted to form slurries. The minerals are extracted from the slurries through a series of flotation and/or sedimentation steps with the aid of water-soluble separation chemicals typically known as reagents. Following the mineral extraction, the resulting residual wetted ore cuttings are labeled as tailings. At the end of the extraction process, the tailings are in a thick semi-fluid sludge state, often with trace elements of the extraction reagents.Historically, these tailings are deposited in giant basins or sludge ponds, where they pose a great threat to the environment while binding large volumes of waste process water.Process water recovery and achievingdry tailingsCurrent generation engineering studies, trials and successful field implementation have shown that an alternate process known as dry stacking is practical. The dry stacking process deposits dewatered tailings into containment areas that are smaller in overall footprint and significantly safer by reducing the transfer of reagents into the tailings storage area. In addition to achieving the dry tailing benefits mentioned, it is possible to recover valuable process water while dewatering the tailings sludge utilizing modern separation technology."

Jan 4, 2018

At the 25th Peruvian Mining Convention, the start-up of Antamina was called ?the mining event of the year.? Antamina, one of the largestcopper-zinc mines in the world, began operations in May 2001.Augusto Baertl is Executive Chairman of Compañía Minera Antamina, the operating company. He said in a convention address that Antamina would be in full production in 2002. ?I would like to stress that Antamina is, in every respect, a highly stringent operation, as it intends to be the Peruvianmine of the future,? Baertl said. ?Antamina has set the target of being, and remaining throughout time, a model mine as to technology, environmental practices and social responsibility.? [ ] In the areas of technology and operations, Baertl noted that ?we have incorporated the best engineering design available and state-of-the art technology for mining, grinding and transportation processes, among others.? In the environmental area, he said that ?we have carried out careful environ-mental impact studies and have incorporated modern technologies and methods to control and minimize any environmental impact.? In the social field, Baertl noted that ?our relationship with neighboring communities is being developed under the premises of the social responsibility philosophy.? These include popular consultation processes, environmental committees and conciliation discussion committees. The purpose, he said, is to encourage communities located within the area of influence of the project to find and lead by themselves their path toward sustainable development, beyond the life of the operation itself.?

Jan 1, 2001

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are some of the most widely used instruments in a variety of industrial applications. Their major functions are to sort, classify and separate solid particles and liquid droplets within a multiphase flow system. Research studies employing both experimental and numerical methods recognize that the performance of a cyclone is related to its geometric dimensions as well as the inner flow pattern. Although many successes have been achieved over the past years, the majority of investigations only focused on the simplified design of cyclone geometry and on single-phase flow. Therefore, this study set out to investigate the flow field in a new-design hydrocyclone and used particle image velocimetry (PIV) to explore the complex swirling flow behavior inside the cyclone within an air core. The flow field inside the cyclone was also studied by computational fluid dynamics (CFD) simulation using a commercial CFD package. Different turbulent models were tested in this study with a moderate-size mesh, and the interface of liquid phase and air phase was predicted by the volume of fluid (VOF) model.

By J. B. Boisvert, O. Leuangthong, T. Acorn

Optimizing final pit limits for stochastic models provides access to geologic and economic uncertainty in the pit-optimization stages of a mining project. This paper presents an approach for optimizing final pit limits concurrently over all realizations in a stochastic model and using a risk-management framework to manage the geologic and economic uncertainty. A heuristic pit optimizer is used to find multiple uncertainty-rated pit shells. These uncertainty-rated pit shells follow the mean-variance criterion to approximate the efficient frontier for final pit limits. Stochastic dominance rules are then used in a risk-management framework to further eliminate suboptimal solutions along the efficient frontier. This results in a smaller set of final pit shells that can be further analyzed for production scheduling. Additionally, the original solutions are analyzed for changes in the mining limits, and two regions are targeted as potential regions for further exploration.

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

Manufacturers have improved various stirred mill types to be well adapted to fine and ultrafine grinding applications. These stirred mills, which are operated in wet or dry conditions, may be classified as horizontal — such as AHM-horizontal agitated media mill, IsaMill and Drais mill — or vertical — such as tower mill, Vertimill, Maxmill, Stirred Media Detritor and ATR vertical agitated media mill. The main difference between vertical and horizontal structures is in their operational variations. Additionally, the scaling-up of mills is also an important parameter for selecting the suitable orientation [1]. The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch-type stirred mill. The experimental results were evaluated using stress intensity analysis. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1 × 10−3 to 5 × 10−3 Nm at 750 and 1,500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value.

By CAIJUN CHEN, MING ZHANG, ZHENWEI WU, FENG ZHOU, BOQUAN LI, XILIANG ZHANG, ZHOU PU

Traveling grate is a widely used process for iron ore pellet production, but the thermal state of pellets in the drying section is still unclear. In this study, the temperature distribution of the drying section was investigated using computational fluid dynamics (CFD). The results indicate there is a coupling effect in the drying section of a traveling grate. Gas with higher temperature in down-draught drying (DDD) transfers heat to the up-draught drying (UDD) through the gap of the insulation board, and the temperature gradient of the pellet bed changes before reaching the insulation board. The characteristics of pellet bed expected to appear in DDD are displayed in UDD in advance. To verify the model, a contrast experiment was conducted.

When multiple mines operate in an area there are social, economic and environmental impacts which cumulate over space and time. These impacts require special attention. A collective approach is required to identify, assess and manage them. No assessment of sustainability of mining can be considered complete without accounting for cumulative impacts. This paper proposes a framework and typology to deal with cumulative impacts and tests this in a coal mining area in NSW Australia.

Jan 1, 2007

By K. N. Han, J. J. Kellar, Y. Guan

The adsorption of zinc species onto silica in ammoniacal solutions was studied. The adsorption isotherms indicated that the adsorption of zinc increased with increasing pH. The adsorption density increased as the zinc equilibrium concentration increased up to =3.5x10-4 M. Above this concentration, the adsorption density was independent of the equilibrium concentration, and a maxima adsorption density was reached. Temperature had no significant effect on the adsorption density.

Jan 1, 1995

By S. S. Peng

This paper presents a computer program package for predicting surface movement and deformation caused by under-ground coal extractions. It is capable of: predicting final surface movement and deformation over underground openings; predicting dynamic surface movement and deformation process associated with underground lingual mining operations; processing and bookkeeping subsidence survey data; recommending subsidence parameters for those new coal mines where no subsidence data are available; and deducting subsidence parameters from collected subsidence data.

Jan 1, 1986

By S. A. Saki, J. F. Brune

"INTRODUCTION Longwall coal mining leaves large areas where the coal has been made removed and the roof rock strata collapse, forming a zone of broken rock rubble called the gob. Figure 1 shows a typical longwall gob area along with the gate roads. The ventilation pattern for progressively sealed longwall panels follows a simple “U” pattern where fresh air is coursed inby to the headgate, flows along the face and exhausts through the outby tailgate as shown in figure 1(a). An important variation of this pattern is the back return (BR) arrangement where the exhaust air from the face is drawn inby and around the nearest open cross cut before it turns in the outby direction towards the exhaust fan. Figure 1(b) illustrates the use of back return. This arrangement moves the point of low pressure from the tailgate corner up to 60 m inby and thus maintains fresh air in the tailgate region that could otherwise be contaminated with gob air.The gob area may contain remnants of unmined coal or parts of overlying coal beds that continue to release methane, eventually filling the gob area with methane in concentrations far above the explosive range of about 4.5 to 15%. Many gob areas must be equipped with gob ventilation boreholes (GVBs) to extract methane, and GVBs often exhaust methane at concentrations from 50% to 90% (Saki, 2016). Due to oxidation processes occurring in the gob, the oxygen content is reduced to a low level, with nitrogen and CO2 making up the major remaining components of the gob atmosphere. FORMATION OF EXPLOSIVE GAS ZONES IN GOBS Since the longwall face area is ventilated with fresh air below 1% methane and the face and gob areas are not separated, an explosive fringe will form where the methane content lies within the explosive range and oxygen content remains above 12%. Figure 2 shows a typical development of such an EGZ. This figure is based on a computational fluid dynamics (CFD) model developed by CSM researchers to analyze gas concentrations and flow patterns in longwall mining. Figure 2(a) shows the formation of EGZ in the gob with a U type ventilation scheme, where EGZ lies right behind the shields in the tailgate corner. Figure 2(b) shows the formation of EGZ in the gob combining U type ventilation scheme with BR, where EGZ is pushed away from the face deep into the gob. The CFD modeling parameters and boundary conditions have been verified with field data from two cooperating, active longwall mines (see Worrall 2012, Marts 2015, Gilmore 2015 and Saki 2016). Other mine geometries, methane inflow rates and gob permeability distributions can be modeled to establish representative gob atmospheric conditions. Two GVBs were operating in the model, extracting 0.165 m3/sec each. The methane in the working areas and returns was kept below 1%. Methane flowing into the model from a rider coal bed above the mined seam was at the rate of 0.55 m3/sec."

Jan 1, 2017

By R. D. Williams

"In a very real sense, Butte, MT is where the copper came from that won two world wars. The price for that unrestricted mining and smelting of copper came due in 1983 when Butte was declared a Superfund site.One of the most complex remnants of this mining history is the Parrot Tailings site. The Parrot smelter operated from 1881 to 1910, moving Upper Silver Bow Creek to the south and depositing approximately 283,000 m3 (370,000 cu yd) of waste material adjacent to Upper Silver Bow Creek. Additional mixed waste from other processing sites deposited below the Parrot tailings at the Northside Tailings, Diggings East and Blacktail Creek Berm total approximately 171,000 m3 (224,000 cu yd) of contaminated material. As part of the Superfund remedy, the U.S. Environmental Protection Agency (EPA) proposed leaving all these wastes in place. This proposal prompted a detailed criticism by several geoscientists familiar with the site. The EPA’s 2006 Record of Decision (ROD) did in fact leave these wastes in place, which set the stage for a series of studies that continue to refine how best to protect extensive completed Superfund Remediation downstream of Upper Silver Bow Creek. History of the Parrott Mine and tailingsPlacer gold was discovered in Silver Bow Creek, the headwaters of the Clark Fork River only a few miles from the Continental Divide in 1864. This discovery led to a stampede of placer and lode claims. One of the first lode claims located was the Parrot lode, located in the fall of 1864. Progress for developing a mine at the Parrott was slow, and it was not until 1876 that one of the original locators encountered a rich vein of chalcocite. Butte had its first copper mine.The Parrott Mine was patented in 1879 and by 1881 the Parrot, having lost a “t”, concentrator and smelter were built. The smelter and concentrator were an immediate success with a considerable market for processing the district’s rich copper ore. In 1885, the employees of the Parrot smelter bought the Butte Reduction Works, another smelter. In 1885, dams were built on Silver Bow Creek to contain various tailings and related processing byproducts (Fig. 1).By 1890, the various smelters in Butte rendered Butte’s air quality as suffocating (Fig. 2). An 1889 funeral procession was rumored to have gotten lost in the thick smelter smoke and somehow ended up at the Centennial Brewery. A city ordinance was passed late in 1890 in an attempt to control smoke. The Parrot smelter employed approximately 500 men by 1890. Through the 1890s, the tailings produced grew from approximately 91 t/d (100 stpd) to more than 181 t/d (200 stpd). Copper values in the tailings were initially as high as 4 percent, but as the processing improved that was reduced to 1.5 percent."

Apr 1, 2019

By Yang Song, Li Shaokang, Wang Zhiqiang, Wang Jinjun, Li Guofeng, Su Meixuan

The paper investigates the triboelectric charging properties of calcium carbonate (CaCO3) particles under different conditions using a cyclone tribocharger. It explores the effects of airflow velocity, tribocharge material, and particle moving distance on the charge-to-mass ratio of CaCO3 particles. The study aims to provide guidance for the design of triboelectric separation systems for magnesite.

Sep 1, 2023

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimal when the concentrations of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/liquid ratio of 67 g/L, stirring speed of 400 rpm and leaching duration of 60 min. Under these conditions, 90.49 percent and 6.78 percent of Mn and Fe were dissolved, respectively, from the ore sample in a size fraction of smaller than 106 µm. It was determined that the leaching of manganese from the ores was a second-order reaction with activation energy, Ea, of 53.38 kJ/mol. The leaching residues obtained under the optimal conditions were subjected to wet high-intensity magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20 percent Fe and 1.79 percent Mn with iron and manganese recoveries of 56.83 and 66.73 percent, respectively. To the best of our knowledge, this is the first time that a magnetic separation process was used on a residue obtained from the reductive acid leaching of manganiferous iron ores to recover iron.

By Brendan Howard

Rio Tinto has a large globally distributed technical workforce and needs to ensure these employees have the requisite skills to not only manage technical risk and enable safe efficient production, but also ensure they are keeping pace with a fast-changing technological landscape. Traditional approaches to learning struggle for scale and an inability to respond to the extreme diversity of capability development needs. In response, Rio Tinto has successfully introduced innovative approaches to learning and employee engagement via leveraging the power of globally distributed networks for peer-to-peer knowledge transfer and providing mechanisms to recognise, reward and retain the individual technical contributors.

Feb 1, 2024

By A. Martikainen, S. GYAMFI

Luossavaara-Kiirunavaara Aktiebolag’s (LKAB) Konsuln iron ore mine, located just south of the famous Kiruna iron ore mine in Malmfälten in northern Sweden inside the Arctic Circle, was developed as a test mine between 2018 and 2020 for the Sustainable Underground Mining (SUM) project [1]. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 Mtpa using conventional diesel machines. The design was created by Kiruna mine ventilation team, Stina Klemo and Joakim Jonasson, in cooperation with a consultant, Tomas Bolsöy from EOL Vent Mining AB. There is a plan to increase this rate to between 1.8 and 3 Mtpa in the future, and this requires the primary fans to be upgraded. Therefore, a study was carried out to determine whether using ventilation on demand (VOD) could avoid this fan upgrade and reduce Konsuln’s ventilation and heating power costs in the future. The study also investigated whether using battery electric vehicles (BEVs) along with VOD or as a standalone strategy could further reduce these power costs. In addition, the study analyzed the suitability of heating power reduction strategies presently or previously used in Nordic countries and Canada to investigate potential additional strategies to reduce heating power cost, the largest portion of Konsuln’s ventilation and heating power costs.

By Mike Ghassemi

It is clear that precise overground and under-ground mapping is an important factor for all designers. Due to rapid changes in underground construction, tunnel designers are increasingly in need of updating project information. This article explains the latest techniques for detecting under-ground utilities as well as underground mapping. Global Positioning System (GPS) is a very ac-curate and popular navigation and mapping system that has been used extensively above ground, but is not used for underground mapping as signals are not strong enough to pass through ground or water. Most underground techniques were developed for military applications during the first and second world wars. Later, the techniques became public. For example, ground penetrating radar was developed for the military in 1970 to be used for locating tunnels under the demilitarized zone between North and South Korea. Later, the same technique was used for detecting unexploded ordinance such as plastic land mines.

Jan 1, 2011