Search Documents

By M. Guzman, M. Romero, S. Bravo-Thais, M. Flores

The phytoremediation method is proposed to recover valuable metals from polluted soils. In this sense, the objective of this research is to determine if it is possible to use native plants in the recovery of precious metals from abandoned mining liabilities. The tailings samples containing Au and Ag were acquired from the northern region of Peru. Two native plant species, Stipa Ichu and Cortaderia Nitida, were used. Results show that Au was recovery around 19% (1.52 mg/Kg) and 25.43% (1.78 mg/Kg) by using Stipa Ichu and Cortadeira Nitida, respectively. Besides, Ag had a better recovery in the Stipa Ichu reaching a value of 6.83% (0.628 mg/Kg); in contrast, Cortadeira Nitida had an efficiency of 3.6% (0.814 mg/Kg). Bioaccumulation, bioconcentration and translocation factors were calculated by determining the concentration of precious metals in the roots and aerial parts of each plant. Results show that Stipa Ichu had a greater capacity of hyperaccumulated Ag compared to Au; while Cortaderia Nitida tended to have a better performance for Au. In conclusion, both plants are recommended for phytoremediation of mining liabilities.

Feb 1, 2023

By Jasinder S. Jaspal, Bradley J. Bourquin

Introduction Operation is underway at the Dutch Creek No. 1 mine of the first US longwall panel to be mined under the cooperative agreement between the US Bu¬reau of Mines and Mid-Continent Resources. The 244-m (800-ft) wide longwall face is part of a multilift longwall demonstration. A 3-m (10-ft) top slice is being extracted from the 8.5-m (28-ft) coal seam. This occurs in an area of the property where the Coal Basin A and Coal Basin B beds have come together to form one seam. This face, longest ever operated in the US, is being worked on an advancing longwall system. During the first months of its operation, this longwall face has been very productive and safe. Mid-Continent Resources operates two coal mines in the Coal Basin, located in the White River National Forest near Carbondale, CO. The Colorado Fuel and Iron Co. originally opened this property in 1895, and conducted a small mining operation for 10 years on the north rim of the basin and then abruptly shut down. Mid-Continent began operations in 1956, after the Coal Basin fields had lain idle for about 60 years. Operations commenced at the outcrop of the Coal Basin B bed situated at the 3-km (10,000-ft) elevation. At this time, coal was produced from Coal Basin A and Coal Basin B seams in the area. Since 1981, operations have been centralized at two mines, the Dutch Creek No. 1 and the Dutch Creek No. 2, both located in the center of the basin. Since 1981, Mid-Continent has shifted its emphasis to longwall mining as the primary method of production, and each of these mines is equipped with state-of-the-art longwalls using shields as the method of roof support. A 4-km (13,000-ft) long twin-bore rock tunnel is being driven at a lower elevation of 2.4 km (8,000 ft) to intersect the coal seams at depth, as they dip 12° in a westerly direction. This tunnel will enable the company to reduce costs by replacing trucks with conveyor belt haulage (Fig. 1). Mid-Continent began longwall operations in May 1976 with the US's first modern, mechanized advancing longwall face, using chocks. In August 1978, a second advancing longwall face was started. Results from two faces showed that the mining system could be used effectively to manage the difficult conditions encountered in both the Dutch Creek No. 1 and the L. S. Wood No. 3 mines. Unfortunately, low productivity and high costs plagued the company's advancing faces. The problems resulted principally from major equipment failures, poorly designed chocks and face conveyors, and the lack of an efficient, cost effective system for building packwalls. Flushing of rock between chocks and roof control were also major problems. In Sept. 1979, Mid-Continent and the US Bureau of Mines entered into a cooperative agreement to demonstrate the feasibility of mining thick coal seams using the multilift longwall mining method. Two lifts are to be used to mine the 8.5-m (28-ft) thick coal seam in Dutch Creek No. 1 mine. The Bureau provided mining equipment for 180 m (600 ft) of longwall face. This included the shields, face conveyor and drive units, shearing machines, panel belt, and stageloader. As a result of previous experience in advancing longwall mining, Mid-Continent purchased an additional 60 m (200 ft) of face, including roof supports and an additional face conveyor. Design The Dutch Creek No. 1 is a slope mine located on the flank of a plunging anticlinal structure that

Jan 1, 1984

By C. M. Brown

The semi-autogenous grinding circuit at the Utah Mines Limited, Island Copper Operation, located on Vancouver Island, British Columbia, is described. Since start-up of the operation in 1971 grinding circuit throughput has been progressively increased from the initial design rate of 30,000 to the current average 45,000 tonnes per day (t/d) of porphyry copper ore. Key developments and modifications in operating and maintenance practice that have contributed to this increase are reviewed.

Jan 1, 1985

By William Gleason

At 6,898 ft below surface, the historic No. 9 shaft at Resolution Copper near Superior, AZ is now the second deepest single lift mine shaft in the United States and connects to the deepest single lift mine shaft in the U.S., Resolution Copper’s No. 10 Shaft (6,989 feet). The shafts serve as ventilation and access for future underground development of what could one day become one of the most significant copper mines in the United States. It is from the base of No. 9 and No. 10 shafts that hundreds of employees of Resolution Copper, a joint venture of Rio Tinto and BHP, hope will soon be given the go ahead to begin driving lateral tunnels to reach a copper deposit that is estimated to contain 28 Mt or 40 billion pounds of copper. Copper was recently added to the U.S. Geological Survey’s (UGGS) critical minerals list, in large part because of increasing demand. A study by S&P Global Energy & Market Intelligence “Copper in the age of AI: Challenges of electrification” released on Jan. 8, 2025, “identifies a transformative trajectory for copper demand, projecting a surge from 28 Mt (31 million st) in 2025 to 42 Mt (46.3 million st) by 2040 – a 50 percent increase that underscores the metal's pivotal role in multiple technological and economic domains.” The surge in demand is driven in large part by the global energy transition, electrification of vehicles, growth of artificial intelligence and data centers, and most recently robotics. Meanwhile, geopolitical tensions have increased the focus on the need for the United States to secure more of its own mineral supply chain. S&P Global’s report is one of many warnings that while copper demand has accelerated rapidly, future supply is being held back. Resolution Copper stands out as one example of a known mineral deposit remaining locked in the United States’ complex and lengthy permitting slog.

Feb 1, 2026

By Peter I. Brooker

The turning bands method for the simulation of spatially correlated data in two or three dimensions requires that the relation- ship between the covariance obeyed by the realizations first generated on lines, and the covariance of the two or three dimensional process must be solved. In three dimensions the solution is immediate, but in two dimensions the integral equation relating the covariances of the one and two dimensional processes is more complex. This is solved in this paper and is applied to the most common model used in ore deposit description, the spherical covariance.

Jan 1, 1984

By Marc Lonoff

Byproducts are more important to the copper mining companies than to the copper market. Copper ores frequently contain gold, silver, molbydenum and cobalt. With the increase in the prices of these metals copper mining has become more profitable. If byproduct prices remain high, additional firms will be attracted to the copper industry; the increased supply of copper will reduce the long-run copper price. However, this is unlikely to happen because the markets for the copper byproducts, especially molybdenum and cobalt, are small. Increased recovery from copper and other sources will depress the prices of these byproducts before the copper price is significantly affected. Should byproduct prices remain high the copper market will both settle at a lower long-run price and be more unstable in the short run. Since changes in the copper price do not affect the entire earnings of a multi-metal mine, the copper price must fall further before such mines reduce output in the short run. Higher byproduct revenues will make copper supply less responsive to copper price; shifts in copper demand will result in greater copper price fluctuations in the short run than they did before.

Jan 1, 1980

By Gregg R. Bierei

Arch of Illinois is a mining complex comprised of two surface and two underground mines located in Perry County, in southern Illinois. The company a division of Apogee Coal Co. of St. Louis, MO. Arch of Illinois' two surface mines, the Captain and Horse Creek Mines, use large stripping shovels and cross-pit bucketwheel excavators to remove overburden from three seams of coal, the Herrin No. 6, Harrisburg No. 5 and Danville No. 7. All are considered high sulfur reserves. The two underground operations are managed by Arch of Illinois. They are the Kathleen Mine and the newly constructed Conant Mine, which began production in 1991. Both underground mines are continuous miner operations. They mine the No. 6 coal, which is about 1.8 m to 2.1 m (6 to 7 ft) thick. All coal is currently transported by truck to a central preparation plant located at the Captain Mine. This preparation plant produces 27 kt/d (30,000 stpd) of clean coal. Production in 1992 reached 5.9 Mt (6.5 million st) of saleable coal. Of that, about 66% or 4 Mt (4.4 million st) are produced by the surface mines and the rest the by under ground operations. Change is in the wind for Arch of Illinois. In 1988, 100% of all production (6.2 Mt or 6.9 million st) came from surface operations. By 1995, only 38% of production is scheduled from surface mines. And by the year 2000, 100% of production will from underground mining methods. Dwindling low ratio reserves, compounded by increasing environmental and land acquisition costs, coupled with more efficient underground mining equipment, have started an evolutionary trend toward development of underground reserves. For Arch of Illinois to maintain profitability of remaining surface reserves and to compete effectively mining underground, it must improve efficiency, productivity and cost reductions. These efforts are essential for maximizing current surface reserves and to ensure a continued existence in the presence of clean air legislation and the softening of the high sulfur coal market.

Jan 1, 1993

By R. D. Stewart

Abstract. Induced fluorescent sorting is a means of beneficiating an ore by selective labeling with a reagent combination which fluoresces when activated by ultraviolet light The reagent combination normally consists of a surface active compound and a fluorescent dye. The surfactant adheres selectively to a specific surface and carries the dye with it. Upon activation with ultraviolet light, the labeled pieces, in the size range 1.27 cm to 20 cm (0.5 to 8 in.), are detected during free fall by photosensitive cells and ejected by water jets. Either ore or gangue may be labeled.

Jan 1, 1980

By J. `. Spitzinger

In situ recovery (ISR) of uranium alters the baseline groundwater geochemistry in order to mobilize and complex uranium to extract and concentrate it. ISR wellfield restoration is often challenging, and primarily relies on groundwater sweep, reinjection of treated permeate, and/or injection of reductants. Greater focus should be placed on injection-based approaches (using existing infrastructure) based on established engineering concepts used for in situ remediation of groundwater plumes. Such injection-based approaches could shorten restoration timeframes consequently reducing long-term operational costs. This paper addresses various types of injection-based approaches to wellfield restoration based on in-situ remediation success with other constituents that require similar treatment. This paper describes necessary design practices for injecting reactive chemicals (e.g., reductants or biostimulants), operations and maintenance (O&M) strategies to prevent fouling of the chemical delivery system and well network, and natural constraints to restoration. Best practices for successful biostimulation strategies that minimize residual uranium, radium, oxoanions, and other trace elements are as described. Advantages of such injection-based approaches could include significant reductions in restoration times, and consequently, lower restoration costs.

Feb 23, 2014

By E. Galán

The largest Spanish kaolin deposits formed on granites occur in Galicia (NW Spain) due to a widespread kaolinization of Variscan granitoids. This paper provides insight of the origin of this kaolinization process on the basis of a mineralogical and geochemical study carried out in two kaolin deposits, presently mined to be used in the paper industry. Mineral composition of the deeply kaolinized rocks is dominated by well-ordered kaolinite with minor quartz, K-feldspar, mica (illite/muscovite), locally gibbsite, and traces of resistant accessory phases (rutile, ilmenite, zircon and monazite). The content and structural order of the kaolinite decrease with depth. Kaolinite formed by extensive replacement of feldspars (plagioclase). Differential mobilization of major and trace elements during kaolinization has been inferred by using a mass-balance approach. Significant amounts of Na, Ca and minor Mn, Sr, P and U were removed from incipiently leachable minerals (plagioclase and apatite), and K, Rb, Cs and Ba were released from K-feldspar and mica. On the contrary, Ti, Zr, Th, Hf and the REE are retained in the resistant trace minerals that are concentrated in the fine fractions of the kaolins.

Jan 1, 2010

By T. M. Klemetti, T. J. Batchler, T. Matthews

From 2013–2017, there were over 1,120 documented injuries, including fourteen fatalities, from ground falls in underground mines in the United States (MSHA 2017). The majority of these ground-fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely used in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded-wire screen as used in underground coal mines by conducting a laboratory testing program using the Mine Roof Simulator (MRS) in NIOSH’s Bruceton Research Center Laboratory in Pittsburgh, PA. The load-displacement characteristics of an 8-ft x 12-ft area of 8-gauge welded-wire screen were evaluated using a test frame designed for testing multiple load-pull locations. In previous tests, load-pull contact was always in the center of the bolted screen section. In this study, larger pull contact areas are used to simulate roof falls. The information obtained in this and similar studies can be used to better understand the loading behavior and surface control capability of roof screen in underground mines. INTRODUCTION AND BACKGROUND The large majority of ground-fall injuries are caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Compton et al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded-wire screen as used in underground coal mines by conducting a laboratory testing program in the Mine Roof Simulator (MRS) in NIOSH’s Bruceton Research Center Laboratory in Pittsburgh, PA. Previous tests to evaluate the performance characteristics of various types of screen have been conducted by the University of Alberta (Tannant, 2001). In this study, the load-displacement properties of welded-wire, chain-link, and expanded-metal mesh were measured by performing full-scale pull tests. A flat steel plate was pulled through a screen test sample that was bolted to a special test frame while the pulling force and mesh displacement were measured. These tests established the general load-displacement behavior of the screen. Peak load capacities and stiffness were determined for each screen type, showing how welded-wire mesh has a much stiffer initial loading response, whereas chain-link and expanded-metal mesh have large displacement capabilities and exhibit significant post-peak ductility.

Jan 1, 2019

"Hecla Limited has been investigating the potential benefits of using a Spendrup/Compact Filter Technic (CFT) diesel filtration system to remove diesel particulate matter (DPM) from the mine atmosphere to optimize use of the available air. The National Institute for Occupational Safety and Health (NIOSH) has evaluated the scrubber efficiency for dust and DPM which is to be presented in another report. This paper reports on a new mining application of a carbon particulate sensor’s ability to continuously monitor long-term mine DPM levels in conjunction with the scrubber evaluation. Magee Scientific is the manufacturer of the Aethalometer®, a continuous black carbon monitor which has been used extensively in worldwide ambient air quality monitoring networks. Two Aethalometers were used at the mine to assess their potential to continuously track underground DPM levels. In this first underground mine application, the Aethalometers were used to continually monitor black carbon (BC) in the intake and exhaust of the CFT scrubber system. Results showed that an off-the-shelf Model AE33 Aethalometer could continually track underground BC levels for extended periods of time over the course of the six-week trial. Data at the scrubber intake over 14 days of testing showed that DPM filtration would be required less than half of the time to maintain BC levels below 50 µg/m3. If the Aethalometer BC data output were “smart coupled” to control a 200-HP in-mine scrubber, significant electrical cost savings would be realized. INTRODUCTION Mine ventilation airflow quantities are calculated to maintain a safe and healthy environment for miners. Dilution of diesel particulate matter (DPM) is often a key factor used to determine the required quantities of ventilation air (Bugarski et al. 2011). DPM emissions and exposure levels are highly variable depending on mine schedules and activities (Janisko & Noll 2010); however, lacking technology to continuously monitor levels, mine ventilation systems are often over-designed in order to handle worst-case scenarios to ensure that DPM levels are maintained at or below regulatory limits. As mines go deeper it becomes more difficult to supply air, and the development of new shafts for air is not economically feasible (Basu et al. 2008). Cleaning and reuse of available air then becomes an attractive option to maintain good air quality."

Jan 1, 2016

By Vytas Svalbonas

Sophisticated computer analysis methods such as finite elements, finite differences, and numerical integration have become tools in the mineral processing industry for design of large mill shells. While use of such methods allows the analyst-designer to take new freedoms with his designed structure, there are also pitfalls and dangers which must be recognized for the proper use of such sophisticated tools. One of the worst of these is treating any computer answers as "gospel truth". The present paper discusses the knowledge required by the analyst-designer for proper use of computer analysis, as well as explaining to the layman how to identify questionable areas in such structural analyses.

Jan 1, 1979

By L. B. Sand

Zeolite ores and protores occur in extensive deposits in the western United States. A recent paper1 describes the general geology and mineralogy of these deposits and their geographical distribution. The zeolites are alkali-and silica-rich varieties of mordenite, erionite, chabazite, phillipsite, ferrierite, and clinoptilolite. The zeolites were formed primarily by the alteration of Tertiary pyroclastics and in some cases by the alteration of Tertiary siliceous flows. The altered pyroclastics are of principal economic significance. The volcanic ash and tuff were deposited in restricted basins where saline lakes developed. The pyroclastic layers often are of uniform thickness and macrotexture for miles from the center of the basin and interfinger with detritals toward the edge of the basin. Thus, in addition to unaltered volcanic glass, the gangue minerals in these deposits include some combination of primary minerals in the pyroclastics, alteration products of the glass other than the zeolite of interest, and detrital minerals. The gangue minerals include quartz, cristobalite, tridymite, opal, orthoclase, micro cline, montmorillonite, hornblende, calcite, gypsum, thenardite, and iron oxides. The presence of one or two other zeolites in the layer in some cases also is considered as gangue. There are no quantitative mineralogical descriptions of these deposits in the literature; this: study was undertaken to obtain this information. As the zeolites occur as single crystals, crystal aggregates, zeolite-glass particles and in cemented aggregates, a method of study was chosen which would give the size distribution of the zeolite in these types of association. For this reason dispersion of the rock was achieved with a minimum of grinding action. This excluded those zeolite ores, silicified by hydrothermal altera¬tion which require grinding. A relative index of the ease of disaggregation of the zeolite ores thus is obtained, but the technique does not give absolute size distributions of the zeolite crystals. Samples were selected for analysis which do not necessarily represent the best ore horizon, but do represent a spectrum of zeolite occurrences from significant deposits. They are mordenite, erionite, and phillipsite from Rome, Oregon, clinoptilolite and chabazite from Reese River, Nevada, chabazite (and var. herschelite) from Bowie, Arizona, erionite from Jersey Valley, Nevada, and erionite from Pine Valley, Navada.

Jan 1, 1967

By T. E. Wilson

An exploration bore core sample of coal ought to be reduced from its original cylindrical form to a particle size distribution and particle composition that reflects, insofar as possible, a process stream of? raw? coal it represents. Often, coal cores are reduced with a laboratory crushing machine, the product of which may not match the raw coal size distribution or size fraction composition. This study employs drop-shatter impact breakage followed by dry batch tumbling in a steel cylinder rotated about its transverse axis in order to characterize the core material in terms of first-order and zeroth-order breakage rate constants. These are indices of the propensity of the coal to degrade during excavation and handling. Initial drop-shatter and dry tumbling tests were done with synthetic cores, to reduce material variables and . conserve difficult-to-obtain coal cores.? Cores of three different coal beds --Illinois No.6, Upper Freeport, and Pocahontas No. 5 -were subjected to drop-shatter and dry batch tumbling tests to determine breakage response. Comparison of coal preparation plant feed with a crushed bore core and a bore core prepared by drop-shatter and tumbling (all from the same Illinois No.6 coal mining property) indicated that the size distribution and size fraction composition of the drop-shattered/tumbled core more closely resembled the plant feed than the crushed core.

Jan 1, 1998

By Kenneth A. Grace

Each and every mining operation from a simple sand-and-gravel pit to the largest integrated mine-mill-concentrator-smelter-refining complex has, as its foundation, a quantity of extractable natural resource the reserves. Without reserves, there is no mine, and any concentrating or extracting plant, no matter how sophisticated, is simply so much scrap metal. And, of course, without resources there are no reserves. It is remarkable, therefore, especially in this age of careful planning, high quality engineering, and state-of-the-art financial analysis, that such a fundamental and vital item is so little understood and the subject- of so much confusion. Time and time again it has been the experience of the author, when called in to a mining operation that has run into trouble in reaching projected production targets, to find that the designed-for tons were not reaching the concentrator/extraction plant, and/or the grade of such tonnage was substantially below the forecast and design grade of the plant. The mill blames the mine for delivering below standard tons and/or grade and the mining engineer blames the geologist for overly-optimistic assessment or incorrect interpretation of the deposit. The geologist blames the mining and metallurgy division for wrongly interpreting his data and conclusions, or simply fouling-up a fine orebody.

Jan 1, 1983

By R. R. Klimpel

The grinding of coal-water slurries has received increasing industrial attention during the last decade. In particular, there is long-term interest in the use of pulverized coal-water slurries to replace oil in combustion equipment and the development of coal gasification/liquefaction processes which require coal-water slurries as feed. More specifically, the use of coal-water slurries in gasification requires grinding a high density slurry containing the smallest amount of water consistent with slurry pumping and spraying. As part of a fundamental engineering research support program aimed at the industrial implementation of dense coal-water slurry grinding, this author has published several papers on how specific rates of breakage vary as a function of slurry rheology, Klimpel (1982, 1982/83). These papers demonstrated that there is a consistent pattern of change in specific rates of breakage of coal in dense slurries with controlled variations in slurry rheology. By matching rheological data with laboratory grinding results, it was possible to identify directly slurry conditions that correspond to: (1) slowing down of breakage rates, (2) the occasional acceleration of breakage of some sizes, and (3) conditions where chemical additives will increase rates of breakage.

Jan 1, 1990

It has been reported previously that dolomite samples from different locations showed varying flocculation behavior with Poly(ethyleneoxide) (PEO). In this study it is determined that palygorskite associated with the Florida dolomite samples is responsible for their flocculation with PEO. A detailed characterization of the dolomite samples from different locations and its relevance to flocculation with PEO is discussed.

Jan 1, 1994

By G. J. Gersbach

The Robe River Iron Ore Project began in 1962 when Cliffs International acquired mining leases in Western Australia's Pilbara Region. Initial reserves were proven and bulk ore samples sent to the U.S.A. for pilot plant testwork. Cliffs Western Australian Mining Company Pty. Limited (30%) manages the project in joint venture with Mitsui Iron Ore Development Pty. Limited (30%), Robe River Limited (35%) and Cape Lambert Iron Associates (5%).

Jan 1, 1983

By Craig Smith

California is the nation's leading producer of diatomite products. The Lompoc Mining District in Santa Barbara County is the world's largest source of commercial marine diatomite. Grefco Inc. exploration has defined a large embayment of commercial grade freshwater diatomite in Shasta County. Exploitation of this massive deposit could substantially increase California's diatomite production.

Jan 1, 1980