Search Documents

By J. J. McDougall

The Windy Craggy copper-cobalt-bearing massive sulfide lies in the Tatshenshini map area of northwestern British Columbia, where British Columbia joins Alaska and the Yukon. The area is covered with numerous glaciers and ice fields that mask geologic detail and hamper ground access. In 1957, Ventures Ltd., the predecessor of Falconbridge Ltd., undertook a reconnaissance of the area using a float-equipped Supercub. At that time, large lakes and glaciers were unnamed and little was known of the geology. The prospecting team was led by J.J. McDougall with Stan Bridcut as pilot-prospector. Prospecting was directed at the St. Elias Mountains between the rich Kennecott copper deposits to the northwest and the Maid of Erin silver-copper mine on the Haines Road, BC. Reconnaissance flying in 1957 and early 1958 eliminated vast segments of the Kennecott-Haines Road terrain as being too inaccessible for mining. In 1958, the Supercub landed at an unnamed lake and the terminal moraine of an unnamed 12.9-km (8-mile) long glacier was prospected. The lake was called Tats Lake and the glacier named Tats glacier (short for Tatshenshini). Float of sulfide was found in the moraine. Follow-up investigation along Tats glacier led to the discovery of several small sulfide deposits and these were staked. Prospecting active glaciers in this area can be complicated because of drainage capture by eroding valley glaciers. Glacier capture resulted in the float from one mineralized area being deposited at different times in three widely separated moraines. Float of the Windy Craggy deposit, therefore, occurs along the course of older glaciers and at the base of the currently active ones. The problem of sourcing caused much additional Supercub reconnaissance. It is interesting to note that about 40 geographic names were given various features in this unmapped portion of the St. Elias Range, and these names were ultimately officially adopted.

Jan 1, 1991

By C. J. Bise, D. A. Poukhovski

Hazard recognition and prevention of accidents are two components of the 30 CFR 48 training requirements, which are mandated for new miners and newly employed experienced miners. These components are also part of the annual refresher training course required of all miners. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine and shall include a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition presents a particular challenge to safety-training specialists, because they are often limited in their ability to adequately gauge the level of awareness of the individual prior to training. Further, they must also assure that the training is relevant and presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics, because it can be used in pretraining and posttraining modes for assessment of training effectiveness, in addition to its use as a presentation tool. This article presents a recent approach, developed at The Pennsylvania State University, that applies the technology for the assessment and instruction of accident prevention through hazard recognition. The application is prepared for surface coal mines.

Jan 1, 1999

By Robin B. Steven

Rio Tinto's Kennecott Bingham Canyon Mine is one of the largest open pit copper mines in the world. In 1988 they completed a $400 million project using a conveying system to transfer the ore from an in-pit crusher to the concentrator. The longest conveyor, C-6, was 17,352ft long and ran in a tunnel through the mountain-side to the concentrator. The belt was removed after 14+ years after carrying 700 million tons of 10 minus ore. The paper discusses the original G6 belt's performance and new splicing methods used to achieve a 60% dynamic splice efficiency on the replacement belt.

Jan 1, 2004

By Vathsala Rajagopal, lwao lwasaki

The grinding media materials for the mining industry require corrosion and abrasion resistance properties not only to minimize the wear but also to improve the flotation recoveries of sulfide minerals. The media wear mechanisms and the factors influencing the grinding ball wear during grinding are discussed with respect to abrasion, corrosion and impact wear of grinding media materials. Interactions between the grinding media and sulfide minerals in a ball mill adversely affect the floatabilities of the ground minerals. The possible galvanic interactions between grinding medium-mineral and their effects on the flotation responses of sulfides are also reviewed. The selection criteria for alloy composition that reduces the overall wear along with adverse effects on flotation are brought out.

Jan 1, 1992

By Alan E. Isaacson

Extensive gravel deposits exist within a six-county area in the mountains surrounding the Salt Lake Valley, and in the mountain ranges to the west. The six-county area includes Davis, Salt Lake, Summit, Tooele, Utah, and Wasatch Counties. The majority of these are beach deposits from prehistoric Lake Bonneville. However, real estate development associated with a projected population increase of 54 percent over the next 20 years is expected to remove most gravel deposits in Salt Lake County from consideration for mining, forcing gravel operations to relocate from eastern Salt Lake Valley to the Oquirrh and Stansbury Mountains farther west. The gravels in these ranges are of lower quality and require additional processing to manufacture asphalt and concrete. Replacing gravel resources along the Wasatch Front with resources in the Oquirrh and Stansbury Mountains over the next 20 years has the potential to increase construction costs by nearly $1 billion. The majority of this cost (82 percent) is the result of increased transportation costs due to longer distances to market. The remainder of the cost is attributable to lower quality gravels that will require additional processing in the manufacture of asphalt and concrete. The following analysis and discussion does not take into consideration the amount of crushed stone that is currently being used in the construction industry in northern Utah, its use as a substitute for lower quality gravels, or as a factor in the base case projection.

Jan 1, 2001

The world's largest hydraulic excavator was recently introduced at Syncrude's North Mine at Fort McMurray, Alberta, in Canada. O&K's 826t (910-st) behemoth RH400, with a 42-m3 (55-cu yd) bucket, is capable of loading 72.5 t (80 st) in one pass. Syncrude's Alberta operation is the nation's largest single source of crude oil. It is also the world's largest producer of oil from oil sands. Syncrude produces 205,000 bbl/day, expects to increase production to 225,000 bbl/day by 1999 and to 320,000 bbl/day by 2005. That translates to 73.5 million bbl of Syncrude Sweet Blend (SSB) produced in 1996, 82 million bbl in 1999 and 114 million bbl in 2005. The North Mine is a new development that will replace the current East Mine, to be depleted of oil sand by the end of 1999. The North Mine will feature hydrotransport, a new and unique method of transporting oil sand from the pit to the process plant. Oil sand from the truck-and-shovel operation will be processed through a double-roll crusher and placed in a cyclofeeder where it mixes with hot water. The material is then screened and transported by pipeline to the extraction plant. Hydrotransport will replace conventional conveyor transport for moving raw product from the pit. Mine development will also use two 290-t (320-st) haul trucks to compliment the fleet of existing 218-t (240-st) trucks.

Jan 1, 1998

By Shigeru Sarata

Working places in underground mines are formed by digging. The main feature of underground working places is that they are surrounded by rock. Digging through rock, which is main operation of mining, generates great reacting force. In many cases, supports are required to maintain a roof. Working places change their location with progress of mining operation. Therefore, for automate the work in such environment, a locomotive mechanism which can endure great reacting force, can support effectively the roof and floor, and has high moving performance in rough environment, might be required. In narrow underground environment which is surrounded by rock, it is possible to generate great fixing force by means of a jack which is set between the roof and floor or both side wall it is usual to apply a jack as anchor post for fixing machinery or reacting force. Self advancing supports widely used in long wall faces in coal mines could be said an example of locomotive mechanism with propping up fixing method. However it is difficult to say that ordinary self advancing supports have enough adaptability for various condition of the roof and floor. New locomotive method for underground working place 'Swing Phase Locomotion' is proposed. It is achieved by mechanism based on frame type support and synchronous control of jacks. Furthermore, to achieved high adaptability to various conditions of the roof and floor, another walking mechanism has been developed. The mechanism employs propping up jack as its legs.

Jan 1, 1989

By Gustavo G. Pilger, Jair C. Koppe, João Felipe C. L. Costa

Information for mine planning requires to be close spaced, if compared to the grid used for exploration and resource assessment. The additional samples collected during quasi-mining are frequently located in the same pattern of the original diamond drill holes net but closer spaced. This procedure is not the best in mathematical sense for selecting a location. The impact of an additional information to reduce the uncertainty about the parameter been modelled is not the same everywhere within the deposit. Some locations are more sensitive in reducing the local and global uncertainty than others. This study introduces a methodology to select additional sample locations based on stochastic simulation. The procedure takes into account data variability and their spatial location. Multiple equally probable models representing a geological attribute are generated via geostatistical simulation. These models share basically the same histogram and the same variogram obtained from the original dataset. At each block belonging to the model a value is obtained from the n simulations and their combination allows one to access local variability. Variability is measured using an uncertainty index proposed. This index was used to map zones of high variability. A value extracted from a given simulation is added to the original dataset from a zone identified as erratic in the previous maps. The process of adding samples and simulation is repeated and the benefit of the additional sample is evaluated. The contribution of an extra sample was evaluated locally, globally and in terms of variation in total measured resources. The procedure showed to be robust and theoretically sound, mapping zones where the additional information is most beneficial. A case study using coal seam thickness illustrates the method.

Jan 1, 2002

By Brian P. Stapleton, Bill M. Stewart, Joel R. Warneke, Curtis C. Clark

Of the 28 accident/injury classifications listed by the Mine Safety and Health Administration, handling materials is second only to roof falls in terms of generating the highest number of reportable accidents in active underground coal mines. Two materials-handling activities that cause numerous injuries each year are the categories of ‘handling supplies or material, load and unload’ and ‘moving power cables.’ Mechanization and mine worker activity training are two methods that can aid in preventing these injuries. This paper describes three mechanical methods – the mobile manipulator, the in-mine hoist, and a cable-handling system - being developed and tested at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Two of the devices are specifically designed for loading, unloading, and moving supplies and materials, and the third device is for handling trailing cables in the confined spaces of coal mines. Also described are safety solutions developed for underground coal mines geared to showing miners safe and unsafe ways of performing various materials-handling tasks.

Jan 1, 2005

By J. W. Choung, J. A. Finch

Acid rock drainage (ARD) is a recognized environmental challenge facing mining industries. An ambient temperature ferrite (ATF) process has been investigated for treating ARD. Most nonferrous metal and calcium ions present in typical ARDs were found to be detrimental to the ATF process. Three approaches were examined, including C02 aeration, addition of complex agents and use of magnetic seeds. By introducing magnetic seeds in the ATF process, the interferences were minimized and all the precipitates formed with lime neutralization were magnetically recovered from a simulated ARD. The residual concentrations of major metal ions in the treated water were environmentally acceptable. The XRD pattern confirmed the spinel ferrite crystal structure of the products

Jan 1, 2000

By R. J. Sweigard, R. V. Ramani

The effects of postmining land use planning are addressed in this paper. These effects may include savings in reclamation costs and increased value of reclaimed land. However, this may result in greater planning costs and possible delays in production. Therefore, an economic analysis was undertaken in an effort to determine the importance of each potential result and to quantify the overall economic impact of postmining land use planning. A discounted cash flow analysis was performed using a surface mine cost model to analyze the sensitivity of selling price to changes in various postmining land use planning parameters. As a result of this analysis, it was determined that the profitability of a project is most sensitive to delays in production, particularly if the delay occurs after major investments have been made. Many methods have been proposed for evaluating postmining land use alternatives (Sweigard and Ramani, 1981). Both quantitative methods, such as benefit-cost analysis (Brock and Brooks, 1968), and nonquantitative methods have been proposed. The application of one specific analytical method is pursued in this paper.

Jan 1, 1988

By R. J. Lutton

The suitability of large-stone materials continues to present occasional problems in US construction. Distinctive modes of rock deterioration cracking, spalling, delaminating. disaggregating, disintegrating, and dissolving help to distinguish causes of deterioration. Design requirements, costs, and environmental factors remain critical to performance. The rating of material quality from superior hypes such as granite to marginal types such as conglomerate is too simplistic but may be useful in a preliminary way. Regardless, the market is dominated by limestone/dolomite material types because of their widespread availability. Certain tests that have been standardized are widely accepted and used for evaluating stone as riprap and armor. These tests are adapted from those used extensively for concrete aggregate; they explore the resistance of the rock to destructive processes such as abrasion, freeze-thaw, and wet-dry environmental attack. The field evaluation of the rock source is often as important as testing. Important limitations imposed by natural jointing and variations of bedding are documented in this manner. The field examination also supports the testing by estimating how much of the quarry is rep¬resented by each of the samples to be tested. Finally, quarrying and processing methods and transportation are carefully considered in regard to stone quality, average size, size gradation, and cost.

Jan 1, 1990

By L. J. Dahl, S. E. Paulson, H. L. Kuhlman

To provide basic information on the processes occurring during in situ leaching, the US Bureau of Mines developed a geologic characterization research program. This includes laboratory experiments wing leaching apparatus that can accommodate whole core samples. Whole core experiments result in a higher proportion of ore mineral contact by the leach solution than packed column experiments. They also allow for the assessment of permeability changes taking place as the result of mineral dissolution, precipitation, and clay swelling within the flow channels of the rock. The leaching apparatus developed can be wed for either constant-pressure or constant- flow rate experiments and allows for the control of flow rate, pressure, and temperature during the experiments. Details of the experimental apparatus are presented, as well as preliminary results from the first series of experiments on an oxide copper ore from the Casa Grade, AZ area.

Jan 1, 1988

By K. V. K. Prasad

Solution of most engineering problems requires, in addition to vast numerical calculations, substantial use of practical judgement and expertise. With advances in applied mathematics and computer technology, the numerical aspects of problem solution have reached a considerable level of maturity. However, it is only recently that approaches like the expert systems methodology have been developed to incorporate the judgemental aspects as well. For rapid development and prototying of expert systems, expert system building tools or "shells" have become widely available. For the expert system developer, identification of the key characteristics of the problem domain and selection of the right expert system tool are of crucial importance. In this paper, the important attributes required in an expert system shell for use in the development of a mine ventilation planning expert system are discussed. These attributes are general in that most engineering problems in mining would have these requirements. Also, the results of an exercise undertaken to evaluate commercially available shells for application to mining engineering problems are presented.

Jan 1, 1989

By J. Duran

Mining at Phoenix is currently done by surface operation in the Fortitude and Bonanza Pits, at a combined rate of approximately 110,000 tons per day. A portion of the ore bodies targeted by these pits was mined previously by underground mining methods, dating back to the mid to late 1800?s. Most of the underground workings (voids) are located in the west central area of the Bonanza Pit. The surface operation requires excavation through voids, and there is a risk of pit floor subsidence that has to be addressed. This paper presents a review of the risk mitigation measures that were implemented to reduce risks to people and equipment working in the area.

Feb 23, 2014

By J. R. Cobble

The Bureau of Mines has developed a process to improve the leaching kinetics of diffusion controlled systems. The system features the Bureau-developed turbomill, an attrition grinder which scrubs the reaction product coating away from the unreacted mineral grains during leaching. The system can be continuously operated at any temperature up to the boiling point of the leaching agent. This paper describes the research on the dissolution of chalcopyrite with acidified ferric sulfate which forms a sulfur product on the unreacted chalcopyrite surface. This method is a hydrometallurgical alternative to chalcopyrite smelter technology which eliminates S)2 emission problems with its associated costs. Batch testing at 90? C with the chalcopyrite/ferric sulfate system resulted in better than 99-pct extraction of copper. At an optimal energy consumption of 1,520 kW h/st, 95 pct of the copper was extracted. Recent work has been directed to development of a continuous system and SX/EW treatment of the resulting pregnant liquor from the chalcopyrite/ferric sulfate leach.

Jan 1, 1991

By R. L. Keiski, H. Miettunen

"The serpentinite massifs of Hitura are located in the municipality of Nivala in Central Finland. The most important sulfide minerals in the ore are pentlandite, pyrrhotite and chalcopyrite. The ore body consists of amphibolite rocks in contact with serpentinite against mica gneiss. The mean Ni grade of the ore is about 0.7%, and the highest Ni grades have been encountered in close contact. In general, the inner parts of the ore are strongly serpentinized ultramafite and some sulfides have been converted to mackinawite and valleriite. The degree of alteration varies considerably within the ore body and, correspondingly, the grain size of the sulfides varies as well. In this study, flotation tests were done with samples from different zones of the ore body. The flotation test results on the bench scale and plant scale are discussed in terms of the mineralogical features of the ore. Ores in the North Hitura zone differ from those in the South Hitura zone.IntroductionThe Hitura nickel mine, like the entire Nivala area, is part of the Bothnian Svecokarelian schist zone, where numerous Ni-Cu boulders have been discovered since the early 1930s. The Nivala area has therefore been the subject of exploration activities by the Geological Survey of Finland (GSF) and mining companies. The first period of exploration started in 1936, and the Makola nickel deposit, located 3 km south of the Hitura mine, was discovered by GSF in 1937. About 415,000 tonnes of ore were mined at Makola between 1941 and 1954. In 1937, during the exploration and development stage of the Makola mine, boulder tracing and a geophysical survey revealed a significant ultramafic body with some lowgrade Ni-Cu occurrences in the South Hitura zone.In 1961, GSF continued the exploration program in the area and discovered the North Hitura ultramafic complex and its allied Ni-Cu occurrences. In 1964, Outokumpu Oy bought the property and, after underground exploration, comprehensive mineralogical studies, process research and a feasibility study, production started in 1970 (Isohanni et al., 1985)."

Jan 1, 2015

By T. W. Peterson

There are two approaches to developing a minicomputer based application for an industrial grinding circuit. Usually, the control program is coded and compilation-debugged on a large-scale scientific computing system or the minicomputer itself if the machine is available. Final debugging and testing must wait for installation and checkout of the entire minicomputer system. Two immediate disadvantages of this approach are the need to obtain, install and check out the hardware before the final debugging stages of program development can begin, and interference with normal mill operation during such final testing. This work reports on an alternative to the usual procedure. Here both compilation and execution bugs are eliminated from the application program before hardware installation by testing the control program against a reasonable dynamic simulation of the entire process. Thus, software development can be completed before the target mini is installed. Such off-line development requires a reasonably accurate mathematical model for the entire process system as well as a suitable simulation package for communication between the simulated environment and the minicomputer application program. Specific data describing the design configurations and dimensions of the mills, cyclones, sumps, pump characteristics and analog controller configuration were supplied by ANAMAX for a grinding division consisting of a rod mill followed by two ball mills in parallel. This information was used to set up a plausible model structure. Steady state ANAMAX data on particle size analysis at various points in the circuit and corresponding values of flow rates, pump speeds, sump heights and slurry densities were used for model parameterization. The preferred operating control strategy - "best grind at operator-set rod mill feed rate" - was set by ANAMAX. An inferential particle size analysis technique using the cyclone cluster as an on-line particle size sensor was used in a novel control strategy_ to achieve the stated objective. Two disturbances common in the ANAMAX circuits - rod mill scoop pluggage and shut down/start up of one of the ball mills - were studied in detail. This report out- lines the steps in system development and testing and the results obtained.

Jan 1, 1974

By F. N. Kissell, H. K. Sacks

This study examines the accuracy of area sampling for measuring the dust exposure of mining machine operators in coal mines. The specific objective of this research was to find locations where an area sampler might work better than earlier studies have indicated. The results show that fixed-location area sampling cannot accurately predict the dust exposure of a machine operator, even when the best fixed location is sought, the fixed location is quite close to the operator and the bias due to the dust concentration gradient is corrected. Industrial hygienists have known for many years that area sampling is unsuitable for measuring air contaminant exposures in the workplace. Near contaminant sources, the dilution air and the contaminants are not evenly mixed. Therefore, when workers are near contaminant sources, exposure measurements must be taken from the worker's breathing zone to be accurate.

Jan 1, 2003

By Laurence M. Demers, Douglas C. Kuhn

It has been suggested that radicals on the surface of dust particles are key chemical factors in the pathophysiology which results from the occupational inhalation of coal and silica dust. In addition, oxygenated derivatives of arachidonic acid (eicosanoids) have been implicated as important biochemical mediators of mineral dust-induced lung disease through their role in bronchial and vascular smooth muscle reactivity, inflammation, and fibrosis. Therefore, we assessed eicosanoid production by the rat alveolar macrophage (AM) exposed in vitro to mineral dusts with varying surface chemical characteristics in order to determine if radicals associated with the mineral dub1 could influence the production of pro-inflammatory mediators in the lung environment. Rat AM were exposed to freshly fractured or "stale" bituminous coal dust, as well as untreated silica or silica calcined to 500°C and 1100°C. Prostaglandin E2 (PGE2) and thromboxane B2 (TxB2) levels in incubation medium were determined by specific radioimmunoassay. When AM were exposed to freshly fractured coal dust, PGE2 and TxB2 production were markedly increased. In contrast, exposure of AM to "stale" dust significantly reduced PGE2 and TxB2 production. In vitro exposure of AM to untreated silica resulted in a significant increase in PGE2 and TxB2 production compared to control. However, exposure of AM to silica calcined to 1100°C resulted in eicosanoid levels which were not significantly different from control. These findings suggest that radicals associated with respirable coal and silica particles may play a key role in the ability of mineral dust to activate AM eicosanoid production.

Jan 1, 1991