Search Documents

By K. A. Allison, D. R. Van Orden, R. J. Lee

Continuing analysis of environmental samples for asbestos content has resulted in the misidentification of non-asbestos amphibole particles as asbestos fibers. These errors have received wide publicity (such as in the asbestos-in-crayon story) and have caused unnecessary reformulation of products. The primary cause of these errors has been a poor understanding of mineralogy and analytical techniques among the many asbestos laboratories that arose following the passage of the AHERA regulations. Presented here is a procedure based on published data that can be used to correctly classify an elongated particle as asbestos or as non-asbestos.

Jan 1, 2005

By R. L. Wiegel

Several mineral process modeling and simulation packages are currently available for use in evaluating the performance of alternative process flowschemes. A critical link that has been missing from these packages is the ability to quantitatively model the effect of size reduction on the liberation of the valuable and waste minerals in the ore being processed. Although there have been several approaches taken to this problem over the past 25 years, none has led to a satisfactory conclusion. A technique has been developed for measuring the effective liberation characteristics of magnetic taconite ores, and a program has been constructed which makes use of these liberation characteristics in simultaneously simulating both size reduction and mineral liberation as it occurs in tumbling mills. This is an especially important step in the modeling of magnetic taconite processes, where magnetic rejection of low grade wastes between grinding stages mandates that a predictive capability be available. The current application is specific to magnetic taconite, but it is possible that a similar approach could be used for other types of mineral systems.

Jan 1, 2002

By L. Maday, V. J. Perrone, M. B. Gilbert

INTRODUCTION The Brightwater conveyance system project in King County, Washington consists of constructing about 21 km (13 mile) of effluent and combined influent and effluent tunnels. The influent tunnels will collect sanitary sewerage from the service area and convey it to the new wastewater treatment plant (WTP) site at Route 9 in Woodinville, Snohomish County, Washington. The effluent tunnels will convey treated effluent from the WTP to an outfall at Puget Sound. The tunnels will be constructed primarily under residential areas, busy suburban roads and state highways. This 21 Km (13-mile) soft ground tunneling project faced many design challenges because of the geologic and hydrostatic conditions, long tunnel reaches, and large overburden depths. Boring depths typically varied from 45.7 M (150 ft) to 114 M(375 ft) with a maximum depth of 185.6 M (566 ft) deep. Conventional empirical methods for non-mountain terrain based on a 1:1 ratio of drilled footage per foot of tunnel bore (National Research Council, 1984) for evenly spaced borings provided a good start for the Phase 1 explorations. However a continuation of this approach with closer spacing was deemed inadequate by the geotechnical team for efficiently allocating geotechnical exploration resources for the final design. This paper presents a rational approach that was used to evaluate the value of a particular geotechnical exploration boring, pump test or other in-situ test. The method of analysis, which was initially developed for rock tunnels (Einstein et al., 1978), was modified for the Brightwater project. The method considers the potential construction cost risks resulting from variable geologic conditions, the cost and reliability of the geotechnical exploration and the earned value (cost risk reduction) of performing the geotechnical exploration. PROJECT DESCRIPTION In total the land portion of the conveyance system will include approximately21 Km (13 miles) of tunnels ranging in size from 3.0 to 5.2 M (10 to 17 ft) minimum inside diameter with overburden depths of 30.0 to 168 M (100 to 550 ft) and

Jan 1, 2005

Baja Mining is currently constructing the Boleo metallurgical plant in Santa Rosalia, Mexico to recover copper, cobalt, zinc and possibly manganese products from the Boleo ore. The process involves an acid seawater leach of the whole ore followed by solid-liquid separation and washing of the leach residue. Solvent extraction is used to separate copper, cobalt and zinc from solution. Copper and cobalt are recovered as cathode metal products and zinc as a zinc sulphate monohydrate. Manganese may be directly precipitated as manganese carbonate which can be used as a feedstock for manganese metal production. Laboratory testing has continued to refine various aspects of the process including iron removal, cobalt and zinc solvent extraction, cadmium cementation, cobalt electrowinning and manganese metal electrowinning. The results of this testing are reported in this paper.

Jan 1, 2012

By D. Bessinger, J. Nell

The electrical conductivity of rutile was optimised as a function of time, temperature and gas composition. These optimised conditions were used to treat rutile/zircon feed prep concentrate samples from a South African heavy minerals producer, prior to electrostatic separation. Enhanced separation between rutile and zircon was obtained when compared to untreated samples. Samples treated in a hydrogen atmosphere and cooled in nitrogen showed the best separation when passed through a high tension electrostatic separator using conditions of high sample temperature and high relative humidity.

Jan 1, 2005

By Debasis Deb

The first version of the longwall strata control and maintenance system (LSCMS) has been successfully developed by the Strata Control Re¬search Team at the University of Alabama. The system includes a software package designed to monitor shield leg pressure, interpret the data and predict the forthcoming roof loads and the existence of geological anomalies. It can also detect maintenance problems of the face equipment. The LSCMS was installed underground and connected to the surface terminals at Drummond's Shoal Creek Mine in Alabama. The system has proven to be a useful and practical system for improving safety and efficiency in coal-mining operation. The Shoal Creek Mine is a new, large coal mine operated by Drummond with two longwall panels. The Blue Creek seam is the primary source of coal production. It is located at a depth of 275 to 440 m (900 to 1,450 ft) below the surface with an approximate 2% southwest dip. Typical strata conditions are represented by two stratigraphic columns (Figs. la and b). A fireclay/dark shale parting (called Middleman) 0.2- 0.7-m- (1- to 2.5-ft-) thick exists between the Mary Lee and Blue Creek seams. Mining conditions vary from area to area. This mainly depends on the Blue Creek seam thickness that ranges from 0.9 to 2.9 m (3 to 9.5 ft). The thickness of the Mary Lee and the parting is relatively consistent with a to¬tal of 0.9 m (3 ft). They are mined when the Blue Creek seam becomes thinner. In most of the panels, the immediate roof is composed of sandy shale 1.5-

Jan 1, 1997

By N. Sahin, K. Baris, A. Ozarslan

This paper aims to assess the current and future role of coal in energy strategy of Turkey and evaluates the compatibility of the policies to the EU energy policy and strategy. The Turkish government set targets to utilize more coal reserves of the country in next decades. However, the country is also in the process of becoming an EU Member State, hence, it is expected that the energy policies have to comply with the EU. Moreover, Turkey ratified Kyoto Protocol, thus the country should limit greenhouse gas emissions. Clean Coal, Carbon Capture and Storage (CCS) technologies are expected to become an important instrument for the mid-term reduction of CO2 emissions from coal-fired power plants. An alternative technique to the conventional CCS methods is CO2 sequestration by mineral carbonation. Turkey has significant resources of magnesium silicate minerals (olivine, serpentine) deposits which can be utilised in CO2 sequestration by mineral carbonation method.

Jan 1, 2011

By W. G. Pariseau

Conventional barrier pillars in underground coal mines are intended to protect mains and sub-main entries for relatively long periods of time. Inter-panel barrier pillars that may be used in especially deep coal mines, say, below 800 m (2,400 ft), are intended to protect longwall panel faces and adjacent panel entries for the life of nearby panels. Barrier pillar failures have serious consequences, especially when failure is sudden and catastrophic. Design of barrier pillars is thus of considerable importance to safety and efficiency of operations. Locally, failure occurs at the limit to elasticity when stress tends to exceed strength. Strength of rock is stress dependent, so an analysis of stress is central to rational design of barrier pillars. There are several approaches to stress analysis for coal mine pillar design that range from the simplified but popular tributary area method including variations that use empirical definitions of the tributary area (volume) to more sophisticated numerical methods such as the boundary element method and the finite element method. Despite ease of use, empirical methods are limited and always suspect when applied to conditions beyond their scope of definition, while boundary element methods do not generally include pillars in the solution domain. The finite element method is not so restricted and thus is a natural choice for conventional and inter-panel barrier pillar safety analyses. Caving of roof strata certainly affects the distribution of stress about longwall faces and nearby barrier pillars. Conventional wisdom that considers roof strata to respond as cantilever beams indicates the longer the span the greater are loads on longwall faces and face supports. Failure of roof beams, caving, shortens spans and relieves face and support loads. The same view is applicable to barrier pillars in that long roof spans outside of barrier pillars leads to higher pillar loads than short spans. Hence, caving should be beneficial to barrier pillar safety. However, the benefit may be small depending on the extent of caving and only in the form of a slight reduction in overburden weight transmitted to the barrier pillar, especially in case of inter-panel barrier pillars. FINITE ELEMENT MODEL Finite element models for stress analysis in rock mechanics are formulated in consideration of physical laws, kinematics, and material laws. These models meet the essential requirements for equilibrium of stress, satisfy strain displacements relations, and in a general sense, relate stress to strain through material laws, often referred to as constitutive relations. The last may be complex and replete with nonlinearities. A de facto engineering material law is the elastic model in the form of Hooke?s law for linear, homogeneous materials that may be anisotropic. A limit to elasticity is imposed by strength in the form of a failure criterion or yield function that accommodates triaxial stress states. Examples used in rock mechanics are the well-known Mohr-Coulomb (MC)criterion, the popular Hoek-Brown (HB) criterion, and the Drucker-Prager (DP) criterion. The first is linear in stress, while the second is nonlinear. Both do not include any effect of the intermediate principal stress. The last is also linear in stress but includes the intermediate principal stress. All show an increase in the major principal stress at failure with confining pressure. In the UT2/3 finite element programs, the failure criterion Y is a nonlinear, anisotropic form and is also the plastic potential [1]: [YJI=+ 11NYJI=+- (1) ] where N is an exponent, usually 2, and J2 and I1 are nonlinear anisotropic forms of the second invariant of deviatoric stress and the first invariant of principal stress. The form (1) reduces to DP when N=1and isotropy prevails. When Y = 1, the limit to elasticity is reached and plastic deformation is possible. The material constants that enter (1) are all computed from unconfined compressive, tensile, and, in case of anisotropy, shear strengths. These latter strengths may be estimated from conventional laboratory test data. Of course, joints in field-scale rock masses induce different values. How different is often a matter of conjecture. For comparative studies, laboratory rock properties seem adequate. Inelastic, that is, plastic behavior occurs with strain beyond the elastic limit. Strain hardening, ideal plasticity, and strain softening are possibilities. Ideally brittle behavior with complete loss of strength is an extreme form of strain softening [2]. Caving may also be considered as strain softening with a less drastic reduction of material properties. As intact roof strata fail, fall, and form a rubble pile below, a new material is formed with greatly reduced elastic moduli and strengths, say, 1/100th of the original intact moduli and strengths. From another viewpoint, caving is simply a natural cut and fill process. Input for stress analysis by the finite element method includes: 1. Preexcavation stress state 2. Geology (stratigraphic column) 3. Structure (major faults, joint sets) 4. Elastic moduli 5. Strengths, and specific gravities of each rock type 6. Excavation sequence Output from an analysis includes distributions of: 1. Stress 2. Strain 3. Displacement 4. Local factor of safety (element fs) The last is defined as the ratio of strength to stress and in view of the failure criterion (1), is the ratio [fsJstrengthJstress=] where the numerator is the maximum possible value and the denominator is the actual value of the square root of the second invariant of deviatoric stress. This invariant is a measure of shear stress intensity but also reduces to uniaxial tensile and compressive strengths as the case may be. An fs greater than 1 indicates an elastic state of element stress; a value of 1 indicates the limit to

Jan 1, 2009

By B. Oraee

Accurate estimation of equipment costs is a key factor in feasibility study and evaluation of design alternatives of mining projects. In this paper, capital and operation costs of backhoe loaders are estimated using multiple linear regression (MLR), based on principle component analysis (PCA). These cost functions are consisted of five independent variables; bucket size, digging depth, dump height, weight and horse power. The MLR is conducted in two steps. At the first correlation between independent variables is omitted using PCA technique. Thereafter, MLR functions are established using selected significant PCs and total cost functions are constituted as functions of initial variables. At the end, accuracy of functions are evaluated using mean absolute error rate method.

Jan 1, 2011

By D. W. Partridge, W. Lamb, A. E. Lamb, S. Bird

Due to the constant need to improve SAG mill performance and efficiency, extensive research into all aspects of SAG mill optimization has been performed. This paper will review the current evolution of SAG mill shell liner design and their performance at the Copperton Concentrator. The effect of these liner design changes will be discussed with respect to: • Liner configurations • Mill operating performance, i.e., throughput, power draw, mill control • Mill mechanical performance, i.e., liner wear profiles, liner life, liner breakage, liner hardness • Foundry manufacturing considerations • Economic evaluation of throughput versus liner life This paper will discuss the results of Kennecott Utah Copper’s (KUC) and ME International’s (MEI) test work, providing an insight into the past, present and potential future opportunities of SAG mill liner design.

Jan 1, 2002

By C. Gherghel

The planning and operation of ventilation network systems for uranium mines require special considerations since ventilation is the primary technique of controlling ambient concentrations of radon progeny. The major environmental challenge facing the ventilation engineer is the requirement to dilute radon progeny to below the Working Level Month per year of worker exposure required by law. The application of large airflow volumes and the utilization of low residence times constitute some of the factors considered by the design engineer. Good mine planning and sequencing are also critical for protecting the health of miners. The mine ventilation must have such characteristics as flexibility, high air distribution efficiency, rapid air transit times, zero recirculation and no short-circuiting. A well established maintenance program for all ventilation appliances must be in place to guarantee control of the distribution system. Real-time monitoring systems permit assurance the adequate quality of air is delivered to working places. A case study for an operating mine is used to demonstrate how the ventilation system is successfully managed and operated using the above concepts.

Jan 1, 2009

By Steve Kral

As the current boom in the global mining industry rumbles on, mining companies have had to step up their efforts to replace mined reserves. Many of the majors are replacing and adding to their reserves and resources through acquisitions. This situation has allowed junior mining and exploration companies to do what they do best. They have been re-examining once uneconomic gold, copper and other metals properties with an eye to partnering with a major to develop them. And mines that have been closed for years due to poor economics are being given another look.

Jan 1, 2006

By D. R. Wilburn

The worldwide budget for nonferrous, nonfuel mineral exploration was expected to increase by 58 percent in 2004 from the 2003 budget, according to Metals Economics Group (MEG) of Halifax, Nova Scotia. The increase comes two years after a five-year period of declining spending for mineral exploration (1998 to2002). Figures suggest a subsequent 27 percent increase in budgeted expenditures from 2002 to 2003. For the second consecutive year, all regional exploration budget estimates were anticipated to increase. The worldwide budget for gold exploration achieved about 50 percent of the total amount budgeted in 2004.This was 68 percent, or US$715 million, higher than the reported 2003 budget. The 2004 worldwide exploration budget estimates for copper increased by 70 percent, orUS$237 million, to US$577 million from the 2003 budget. The budget for nickel exploration increased 52 percent, or US$89 million more than in 2003. The 2004 exploration budget for other mineral targets (primarily cobalt, heavy minerals, industrial minerals and silver) increased114 percent, or US$118 million.

Jan 1, 2005

By L. Bergkvist

"History can provide many answers with regard to what today’s mining industry looks like and how we got to where we are today. It has always been self-evident that safety has to be given the highest priority and, throughout history, many mine workers have been injured, become ill and have even sacrificed their lives due to the way in which attempts have been made to extract the ore, often due to ignorance of the dangers being faced. In more recent stages of history we have seen certain dangers being compensated by means of higher wages and bonus systems in order to have the work carried out: one example of this is when the rock heating method was employed and the men who first went underground to put out the fires that were burning, were paid extra. The working conditions, to which these people were exposed, with smoke-filled closed spaces, shortened their life expectancy considerably and today we can ask ourselves whether it is really possible to value these efforts just by higher wages. In all mines worldwide the working environment has been improved and many mining companies have a zero vision where work-related injuries and accidents are concerned. Despite this, incidents of varying severity still occur and a continuous improvement process and ongoing training is necessary in order to constantly minimise risks and improve the working environment. Atlas Copco takes this into account in all its development and we not only review our own production units but also the needs of our customers, with regard to the machinery that is produced in order to cater for customers’ safety and production objectives. Underground mining probably started at the beginning of the 11th century when people with modest tools tried to extract ores that were present in the bedrock. Methodology has developed enormously over the years with a strong focus on increased efficiency and higher production. In different parts of the world the development is driven forwards at different rates depending on which controlling factors are regarded as necessary. Political decisions, profit goals and productivity have partly controlled the development, but the greatest factor where improvement is concerned still remains with increased understanding of the totality. During more than 1000 years since underground mining has been conducted, all individuals at all levels have constantly improved their expertise and the human element has been of great importance with regard to the development that has been made, even though technology often occupies a leading role when we describe the improvements made."

Jan 1, 2011

By R. A. Franks

An evaluation of a nuisance-emissions-discriminating smart mine fire sensor system was made in an operating coal mine. These field evaluations were conducted to determine the sensor system?s ability to discern nuisance emissions, such as diesel exhaust, emissions from flame cutting and welding operations or hydrogen gas from a charging station, from real fires and to compare the number of falsely reported fire alarms generated between the sensor system and a standard carbon monoxide (CO) monitor. The sensor system?s ability to operate successfully in the working environment of an operating coal mine was also evaluated. The smart mine fire sensor system consisted of four sensors whose data outputs were fused with the use of a neural-network-type computer program. Long-term trials were conducted in a haulage way, a belt entry, and a track entry. The system functioned successfully in the belt entry, in accordance with its developmental goals, where the sensor system even discriminated events not anticipated during development. It was not totally effective in the haulage way and track entry, though, due to a combination of significant diurnal air temperature variations, dust, and mechanically induced vibrations. Also, deteriorating rib conditions contributed to operational problems in the haulage way evaluation. In general, the smart mine fire sensor provided nuisance emissions discrimination and was shown to be a viable new approach for mine atmospheric monitoring, enhancing miner safety. This paper describes the in-mine evaluation of the smart mine fire sensor system and discusses recommendations for improving the system. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2008

By Wern-ping Chen, Jean Habimana, Jinyuan Liu, Mirza M. Rabbaig, Robert Barbour

To mitigate and control the combined sewer overflows from 17 outfalls in the City of Detroit, three outfalls in Dearborn Heights and eight outfalls in Redford Township, the Detroit Water and Sewerage Department has completed the preliminary design of a storage tunnel in 2005. In 2006, a final design has revised the alignments and the inside diameter (ID) of the tunnel. The revised tunnel system includes an 11.28-km(7-miles) 9.14-m (30-ft) ID tunnel, a 24.4-m (80-ft) ID pump station, two work shafts about 15.2-m (50-ft) ID each, and 14 drop shafts with various IDs. This paper discusses the latest development of this tunnel system.

Jan 1, 2007

By A. Noble

Traditional simulations of mineral processing circuits are solved by straightforward numerical techniques which require iteration to accommodate recirculating loads. Depending on the complexity of the simulated circuit, this solution technique can be inexact, computationally intensive, and potentially unstable. In this communication, an alternate calculation approach is presented, wherein an exact analytical solution is determined as a function of the individual units? separation probabilities. All the stream data, including recirculating loads, may be solved simultaneously, negating the need for iteration. Furthermore, with an analytical solution available, circuit analysis may then be utilized to diagnose the relative separation potential of the circuit. By integrating these tools, the authors have developed a software package for evaluating circuit configurations. This paper presents the theory, development, and limitations of the software?s methodology along with industrial examples which highlight the tool?s applicability to industrial circuits.

Jan 1, 2012

By Greg Partington, Darryl Thorburn, Charlene Wildman, Elisa Puccioni, Connie Payne, Campbell McKenzie

"Mineral prospectivity modelling of polymetallic nodule deposits has been completed over the Cook Islands Exclusive Economic Zone (CIEEZ) using the GIS based Weights of Evidence modelling technique. Polymetallic nodules, also known as manganese nodules, have been explored as a possible resource for a number of metals including cobalt since the early 1970s. Recent data on the nodule composition and abundance in the CIEEZ has led to a renewed interest in the prospectivity for manganese nodules in the region. The predictive modelling has used the most recently accepted mineral model for polymetallic deep-sea nodule deposition to identify factors that are most likely to map the presence of this type of mineralisation in the CIEEZ.Manganese nodules form on the deep seafloor as concretions formed by concentric layering of iron and manganese hydroxides around a core and they grow at a very slow rate, on the order of millimeters per million years. The available data for the CIEEZ indicates a greater abundance in the area of nodules formed by hydrogenetic processes, which are the result of slow precipitation of metallic components from seawater. The environment in which the nodules are most abundant is at depths between 4,000 m and 6,000 m in areas of low sedimentation rate. Hydrogenous nodules commonly grow on siliceous and pelagic clay sediment, they are less common on other types of sediment."

Sep 1, 2014

By M. L. Harris

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five underground coal mines in MSHA District 2 (Pennsylvania) and three underground coal mines in MSHA District 11 (Alabama). While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (percent IC) determined by the CDEM agreed well with those obtained later by low-temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

Jan 1, 2008

By C. Sykes, E. Turner, M. Wyart-Remy

This paper follows that of the Milos Conf, 2002 and examines the collection and reporting of SDIs in the industrial minerals industry in Europe. It compares the characteristics of the GRI Reporting Guidelines, with its Metals and Mining Sector Supplement with those of the EU DG Enterprise Scheme, launched in 2001. The particular issue of SME's and companies which are not publicly traded is examined. The pros and cons of participating in such schemes is a central theme of the paper. The paper concludes that there and many business benefits for these companies in participating and submitting their data. The European Commission Scheme is strongly recommended for companies in the sector which are SME's and not-publicly traded as well as large firms who are listed on European Stock Exchanges.

Jan 1, 2005