Search Documents

By Z. Abdel-Khalek, Hassan El-Shall, S. Farrah, C. Boice

Selective adsorption and surface modification of minerals by surfactants is the primary step in the process of separating certain minerals with similar physical and chemical characteristics in the flotation process. In this study, microorgan- isms are used as surface modifiers for francolite and dolomite. Results of adsorption experiments with francolite and dolomite show that the microbes selectively adsorb to one of the minerals under specific operating conditions. In preliminary flotation experiments, it is found that the microorganisms enhance or depress flotation of the minerals leading to an increase in the efficiency of separation between the francolite and dolomite. The conditions leading to selective adsorption (surface modification) and subsequently to possible efficient separation of these two minerals are discussed in this paper.

Jan 1, 2002

By B. V. Clingan

A practical application of recent design concepts makes it possible to design a column cell to fit a specific set of conditions. The design and operating parameters Of a column cell installation that replaced a conventional two stage copper flotation cleaning circuit at MAGMA COPPER COMPANY, SAN MANUEL, ARIZONA using these design concepts is described. A survey of other mineral processors using column cell technology was conducted. The results of this survey will also be discussed.

Jan 1, 1987

By Eugene F. Casey, William H. Hansmire, J. Ghaboussi, Randall L. Lentell, Harvey W. Parker

INTRODUCTION Construction of a major intercepting sewer in Brooklyn, New York involved tunneling in soil over several subway lines. In two instances the clearance between the subway and sewer was sufficiently close that concern was raised about the influence of the new construction. Prior to each critical crossing, analytical studies were performed which characterized the tunneling influence. It was demonstrated that with adjustments in construction procedures the crossings could be made without affecting the integrity of the subway linings. A comprehensive program of instrumentation and full-time monitoring was undertaken to ensure that any unforeseen adverse developments during crossing would be recognized. The successful crossings were subsequently made with minimal influence. Reported herein are the special construction conditions for the two crossings, the analytical simulation of behavior, and the results of monitoring on the subway linings. SEWER TUNNEL CONSTRUCTION AND EXISTING SUBWAYS The Red Hook Intercepting Sewer is a 2600 m (8600 ft) long tunnel which is part of a major water pollution control project in New York City. For clarity of nomenclature, the sewer is termed a 'tunnel' while the rapid transit structures are termed 'subways'. For routine construction, the tunnel was mined by hand with a 3.2 m (10 ft-5 in.)

Jan 1, 1981

By Barry N. Doyle, Tarcisio M. Carvalho, Alan K. Haines, Marcos P. de Melo, Edward J. da Silva

A metallurgical complex to recover gold from highly refractory arsenical ore was recently commissioned by Sao Bento Mineraco. The plant, with a nominal capacity of 20 000 tonnes per month, is situated in the Minas Gerais province of Brazil. The process consists of run-of-mine milling, flotation, pressure oxidation of the concentrate, carbon-in-leach, elution and electrowinning, and effluent disposal. The paper provides an account of the investigations that resulted in the decision to install the pressure oxidation circuit, process and engineering design and plant start up. A comparison is made between the results achieved during the first two years of production and the design parameters.

Jan 1, 1989

By J. J. Lewis

In the mid-1970's a major new prospect was proved in a previously unworked region of North East Leicester- shire, United Kingdom. Preliminary estimates from borehole information showed over 500 million tonnes of recoverable reserves. A special Planning Team was set up, to co-ordinate the work for the two local Areas, South Nottinghamshire and South Midlands (management of production of the UK National Coal Board is organised in twelve such Areas). The team was led by one of the authors as Deputy Director, Mining, North East Leicestershire Prospect (NELP). The remit imposed by the National Coal Board was to analyse the possible options of number, location and eventual rates of output of shaft or drift access; to select a recommended alternative in the light of geological, mining, topographical and environmental considerations; and prepare submissions in accordance with standard Board practice on major projects - such submissions including detailed engineering design, financial appraisal, and full risk assessment. To assist the Planning Team, surface and underground consult- ant engineers were appointed to prepare feasibility studies of specific civil and engineering problems.

Jan 1, 1979

By A. I. Kalugin, A. A. Abramov, D. E. Kozlov, D. V. Magazanik

Based on theoretical and experimental researches of phosphate and carbonate minerals flotation in the presence of soluable glass at various pH values and sodium silicate concentrations, it has been established that the presence of soluble glass in solution leads to formation of silicate compounds on the surface of phosphate and carbonate minerals causing change in their floatability for the worse. The harmful influence of soluable salts is done by tying of collector as metallic soaps, forming precipitates on the surface of minerals to be floated and causing their depression of flotation, and breaching of the froth etc. Depressing action of slimes and products of interaction with collector depends on the ratio of values and signs of potentials of the mineral surfaces. The possibility of phosphate and gangue minerals separation can be evaluated by comparing the minimum-necessary concentrations of collector required for their flotation.

Jan 1, 2002

By F. Dakubo

"Solvent extraction of copper pregnant solution (PLS) obtained from ammonium peroxodisulfate assisted leach was modeled using response surface methodology. Mixing speed, pH, reagent concentration and organic to aqueous (O/A) ratio were selected for testing. A pitched blade mixer was used in the experiment. Mixer speed contributed significantly to copper extraction significant, while pH had minimal effect on copper extraction. The response model developed has an R2 = 0.97 and Adeq precision of 28.3. A parallel kinetic comparing study using a straight blade Rushton turbine in a turbulent regime of mixing showed no difference (p-value =0.308) between peroxodisulfate assisted leach PLS and conventional ferric/sulfuric acid leach PLS- the power draw data support this conclusion. INTRODUCTION High arsenic chalcopyrite concentrates are a problem to the smelters all over the world due to high arsenic gas emissions during smelting. Therefore leaching is often the alternative for extracting the copper in these concentrates if dilution with low arsenic concentrate is not possible. High-pressure autoclave leaching is used. Alternatively, the use of stronger oxidants such as peroxodisulfate has been proposed [16, 18]. There is a concern brought up by the hydrometallurgy community about the faith of the organic extracting reagent coming into contact with stronger oxidant residue in the pregnant leach solution (PLS) and hence the efficiency of such extraction process. This work, therefore, looks to answer such concerns. PLS generated from leaching of chalcopyrite concentrate with the peroxodisulfate ion was used in this solvent extraction experiment. As a liquid-liquid extraction, solvent extraction involves contacting the aqueous PLS with organic extractant via mixing. Mixing is known to increase the interfacial area for mass transfer by decreasing the diffusion path length (Jussi et al.1997). EXPERIMENT Instruments and Reagents Reagent grade Acorga 5910 reagent was used in the experiment was supplied by Cytec (Current name Solvay), Ammonium peroxodisulfate and sulfuric acid were reagent grade obtained from Amazon. Apparatus The solvent extraction tests were carried in a 2000 ml plastic cylindrical reactor equipped with four 0.5” baffles. In the hypothesis test, the reactor was a 4000 ml cylindrical reactor with four 1” thick baffles arranged evening in the reactor. Comparison between peroxodisulfate and ferric leach PLS via hypothesis test"

Jan 1, 2018

By F. F. Peng, Y. Xia

In modeling of hindered-settling bed separators, the published separation mechanisms are based on differences of particle density and size distributions, without the details of complexity of particles-liquid interactions. A fluid dynamic model for the separator is developed using Euler-Lagrange approach of Computational Fluid Dynamics (CFD). Fluid motion is obtained from solving the movement of liquid governing equations. The damping effect on flow pat-terns caused by the movement of particles resulted in liquid-particle coupling is included in the model. Effects of particle size, and particle density compositions, feed rate, feed water flow rate, upward fluidizing water flow rate, etc., are simulated in the 2-D separation model. Flow pattern effects on the separation of fine particles in the separators with center downward-flow and side cross-flow feed systems are investigated.

Jan 1, 2004

By B. Andersen, P. Somasundaran

An accurate knowledge of the interactions among mineral particles and between such particles and dissolved and precipitated species is important in developing efficient separation processes. In this investigation, interactions relevant to dispersion and selective reagent adsorption (the two main prerequisites for selective flocculation) within Florida phosphatic clay Waste were studied. Initial studies with artificial slimes, consisting of pure clay and phosphate minerals, showed dispersion of artificial slimes to be relatively easy. The problems that were encountered during selective flocculation of the artificial slimes were due to unselective polyacrylic acid adsorption on clay, which was caused by the presence of multivalent calcium ions on the exchangeable cation positions on the clay surfaces. This problem could be solved by exchanging calcium for sodium, which reduces the interaction between the polymer and the clay surface. This procedure, however, was not successful for mineral mixtures. Natural slimes were found to be much more difficult to disperse. This was attributed to the presence of cementing materials such as humic substances and Al and Fe (hydr)oxide precipitates. Selective removal of these cementing materials resulted in good dispersion and partial separation. A further increase in the separation of natural slimes is most likely determined by the presence of calcium on the clay surfaces, as was found for the artificial mixtures.

Jan 1, 1994

By Keith G. Wallace, K. M. (Chris) Chmura, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) performed a feasibility analysis for the purpose of either modifying, supplementing, or replacing its two main mine fans. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) fa¬cility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Since the centrifugal fans were installed in 1988, multiple op¬erational and performance concerns have been identified. A com¬prehensive engineering study was conducted in 1995 to: 1) Qualify and quantify operational concerns, 2) Evaluate possible alternatives, and 3) Recommend an optimum solution. Multiple system modification and/or replacement scenarios were evaluated with associated cost estimates developed. The study considered replacement with either centrifugal or axial fans. Multiple fan duties are required at the WIPP. Therefore, Variable Frequency Drives and Inlet Vane Controls (IVC) were investigated for centrifugal fans. In-flight adjustable blades were investigated for axial fans. The study indicated that replacing the existing system with two double-width, double-inlet centrifugal fans equipped with IVCs was the best choice. This alternative provided the most desirable combination of: 1) ensuring the required operational readiness, and 2) improving system performance. The WIPP is currently planning to replace the first fan in 1997.

Jan 1, 1997

During 1993, contraction of indus¬trial economies in Germany (-2%), France (-1 %), Japan (-0.1 %), Eastern Europe (-2%) and the former Soviet Union (-13%) dimmed prospects of a robust economic recovery for North America. Some European countries that suffer from high unemployment and large government deficits have non-com¬petitive cost structures that will require long-term economic reforms to solve. Restructuring in the United States also continued in 1993. The sluggish pace of the US economic recovery, in¬troduction of federal tax increases and the persistence of high levels of unemployment did little to inspire consumer confidence. By the end of the year, however, sales of consumer durable and capital equipment began to grow. Depressed demand for minerals by industrial economies in recession was partially offset by continuing rational¬ization or abandonment of non-competi¬tive productive capacity in Eastern Eu¬rope and the former Soviet Union. Al¬though aluminum, lead, titanium sponge and zinc prices fell, increases in copper and steel consumption helped steady their prices along with prices of some alloys. Cash flow to the mining industry - the primary source of exploration funds - was therefore constrained. For many companies, exploration expendi¬tures were reallocated geographically and in terms of commodities sought.

Jan 1, 1994

By Brian Fulcher, John Eastlund, J. B. Copeland

Following the completion of the 7,600 m primary access tunnel by Kiewit/Parsons Brinckerhoff (K/PB) in April 1997, an exploratory East-West Cross Drift Tunnel was constructed at the Yucca Mountain Project over the proposed future repository block for high level nuclear wastes. The 2,681 m (8,796 LF) East-West Cross Drift Tunnel was excavated through volcanic tuffs having zones of incompetent rock using a re-built Robbins 5.000 m (16’-5”) hardrock TBM with a special arrangement of supporting equipment. Details of the unusual site and contract conditions will be discussed as well as with the unique tunnel equipment specified by the Owner. This portion of the Yucca Mountain project required eight months to complete.

Jan 1, 1999

By C. P. Mangelsdorf, Richard A. Allwes

At the request of the U.S. Department of Labor, Mine Safety and Health Administration (MSHA), the U.S. Bureau of Mines evaluated the suitability of using tri-sets for protecting mine personnel in roof-fall prone areas. A steel-set arch provided by MSHA served as a basis for evaluating the performance of the tri- set. All tests and analyses were conducted according to the arch canopy test and design procedures developed by the Bureau. Theoretical resistance functions were established for the steel-set arch and tri-set and were representative of their experimental behavior. The resistance functions were used to determine the energy absorption capacity of the structures and to predict their dynamic response to impact loading. The dynamic tests demonstrated that the arch canopy design procedure is appropriate for tri -sets and yields conservative designs for both steel-set arches and tri-sets. As a result of this work, it is recommended that tri-sets may be considered for protection against roof falls, provided that the arch canopy design procedure is utilized for each application and that the principles underlying the design procedure are understood.

Jan 1, 1992

By K. Pietruszka

The article presents the concept of the application of the Finite Element Method (FEM) and ABAQUS software in the global monitoring of changes in the rock mass and on the surface of the area, as a result of backfilling the workings. Waste materials applied for stabilizing old mining workings can have a strong influence on the rock mass and surface. According to the regulations, this process should be carefully monitored, especially in terms of the safety of surface structures and rock mass stability. The article presents the concept of an analytic and graphic presentation of the results of the measurements of old workings, applying the Finite Element Method and ABAQUS software in model studies. The main purpose of such interpretation of the geodetic observations results is the application of methods providing wide possibilities to present the geometry of workings, their changes and the influence of the rock mass and surface.

Jan 1, 2008

By J. Moreno, P. Sinton, R. Vogwill

Groundwater models are often used to estimate and optimize dewatering volumes, locations, and rates, as well as water supply production for mines. Projections of future dewatering rates are highly dependent on the conceptual model used as a basis for the numerical model. This paper presents an audit of modeled dewatering rates versus actual data and an examination of the reasons for discrepancies. The setting is a gold mine, in a collapsed volcanic crater breached by the ocean. Mining will occur to about 200m below sea level within a remnant geothermal system. A detailed hydrogeologic investigation was conducted to support dewatering and geothermal depressurization design for future mining operations. These studies included development of a three-dimensional model to simulate heat and density-coupled groundwater flow, using software developed by URS/Dames & Moore. In this paper, the groundwater modeling results prepared 5 years previously by others was audited using operational dewatering data. This model was then extended using the new mine schedule and actual locations for dewatering wells to predict future dewatering requirements. In addition, a comparison between “hot” and “cold” model results was used to assess the need to use a heat-coupled versus a standard groundwater model for dewatering predictions.

Jan 1, 2003

By R. Tanaskovic

Unfavourable climatic conditions in stopes are of significant economic and social importance due to the following reasons: - Working effect is much lower leading to decreased output and work productivity disregarding implementation of mechanization. - Manpower operating capability decreases much faster under unsatisfactory climatic conditions. Under normal climatic conditions a workman would expend much less effort in line with a shorter effective time for the achievement of identical production effects since the work would be more efficacious. The objective of study of problems and climatic conditions is to make the working environment in mines suitable for normal development of operations. Lowering of mining works to increasing depths and winning of a growing number of small orebodies over a broad area makes the problem of creating suitable climatic circumstances more complex. Mining costs are growing due to bench conditions in line with decreasing metal content in the ore, so frequently the investments required for creating favourable climatic conditions represent, in addition to the selection of mining technology, a very important parameter when making decisions regarding exploitation. As known, the basic factors affecting climatic operating conditions in mines-are: temperature, humidity and speed of air flow, implying that the climatic operating conditions are closely related to mine ventilation. Usually, the concept of unfavourable climatic operating conditions includes increased mine air temperature and humidity and low air flow velocity so that heat exchange between human organism and the working environment is impeded or reduced to minimum. Metal mines in Yugoslavia are characterized by the existence of a large number of active faces - stopes and horizons and lowering of mining operations to increasing depths, so that face ventilation solutions are more and more complex. Since its foundation (1961), our Institute is engaged in investigation of factors influencing climatic circumstances improvement of calculations for air distribution and distribution control in complex ventilation networks and study of problems related to ventilation of large volume and irregular configuration faces, as well as application of gained knowledge in our mines. The paper presents the knowledge and experience gained in the case of Lead and Zinc Mine "Trepca" - Stari Trg.

Jan 1, 1980

By Jinrong (Patrick) Zhang

Improvement of conventional flotation efficiency, separation of carbonates from apatite, recovery of phosphate values from phosphatic clay and other ways of utilizing the clay, disposal of clay slurries and subsequent reclamation of the settling areas, and conservation of resources and energy remain major challenges in the beneficiation area for the phosphate industry. These problems have been actively investigated by the industry, government agencies, and research organizations for decades with modest success. However, some recent research activities have generated promising results and possible new technologies. The dominant position of the Crago process in phosphate beneficiation is being challenged by some of the single stage processing schemes. Heavy media separation enables one producer to process a portion of high carbonate ores. Separation of dolomite from apatite by reverse flotation of carbonates with phosphate depressants showed potential for industrial application. Consolidation of phosphatic clays in mine cuts using a modified "sandwich" process is being tested. Beneficiation in the acidulation plant or grinding at the mines may be considered in the future.

Jan 1, 1993

By R. V. Ramani

Control is a vital management function by which operations are brought into compliance with predetermined standards to achieve the goals of an enterprise. Events that are characterized by a low degree of expectation, avoidability, and intent necessarily have a low degree of control. Such events are difficult not only to predict but to control as well. Fortunately, very few industrial situations fall into that category of events. It is an axiom of control technology that in order to control, one must first measure; further to measure, one must know the characteristics of the subject (or environment) upon which the measurement must be made. Finally, if measurements are to be made reliably, the influences that affect the measurement must be known and, if possible, understood. The complete control cycle therefore consists of the following: (1) defining the objective, (2) planning to achieve the objective, (3) putting the plan into practice with appropriate instructions, (4) measuring variables or parameters of interest, (5) transmitting and transforming the measurements to analyze the system's status and to predict the future outcome, (6) comparing these with the defined objective, and (7) determining and taking corrective actions to bring the actual results closer to the objective. The management principle underlying the control cycle is the principle of management by exception. The application of the principle and the frequency with which corrective actions are taken vary according to the purposes of the review and control. For example, the control of a machine operation (e.g., truck on a haul road) may require adjustments and therefore data, analysis, and decisions, in intervals of seconds whereas the review for ore-grade control may take several hours. Reviews, on the other hand, for cost control may be done in intervals of weeks or months. In any case, three specific purposes of the control cycle are: (1) to correct the operation so that it follows the accepted plan closely, (2) to evaluate the operation and predict future outcomes in light of changes in the environment or of more experience, and (3) to review the objectives and modify these to be reasonable and realistic.

Jan 1, 1979

By John C. Draper

The principal object of an underground coal mine transportation sys- tem is to move coal from the face where it is produced to the outside of the mine where it is prepared for market. In addition to the movement of coal, a transportation system must also move supply materials to the inside; it must move men in and out of the mine; and it must move rock and other debris out of the mine for disposal. Usually, mine haulage is divided into three categories named for the various areas of the mine served : 1) Pace Haulage. This is used at face from the mining machine to the intermediate transport system. 2) Intermediate or Secondary Haulage. Generally this is used between face haulage and main haulage. Sometimes this is merely an extension of the main haulage. 3) Main Haulage. This extends from the secondary haulage to the outside and is usually either a track or conveyor system, sometimes a combination of both. Transportation modes of coal in the various areas pose different problems, but the whole system must be synchronized. For instance, at the face the coal should be removed quickly from the various places to facilitate the movement of machines, whereas the intermediate system just passes the same coal on to the main transportation system. Selection of the transportation system must be based on the seam height, mining methods used to extract the coal, capacity required, ease of coal handling, and haulage efficiency. When driving rooms, mine cars can be used. They often simplify supply haulage and rock handling because they can also handle these items. Conveyors could be used and would have a greater haulage capacity but they cannot handle supplies easily or segregate the rock. When using a different mining method, such as longwall, mine cars cannot be used because there is not sufficient space to move the cars at the face nor can the cars haul the coal without delays which would cause excessive losses in production. As for ease of handling at a longwall face, conveyors are convenient because of their low height, ruggedness, and ability to operate while being advanced. Similarly, in low seam heights, conveyor systems are easier and more economic to operate than the regular track haulage because roof has to be taken down for handling mine cars of adequate size.

Jan 1, 1981

By Hans-Henrik Wallin

The stresses in the heads and shell of a grinding mill are largely dependent on the bending moment produced by the trunnion bearing. By using spherical roller bearings in a special narrow housing a short moment arm is obtained and the bending moment is reduced. For large mills a hydrostatic shoe bearing which also gives a short arm, can be used. Spherical roller bearings also require less maintenance and have a long service life. As the bearings are grease lubricated an automatic lubricator is used instead of an oil lube system. Service data from two Swedish mining companys confirm the fact that the above arrangements provide a long service life.

Jan 1, 1979