Search Documents

By E. Ashworth

A thermistor probe has been developed to measure in situ temperature profiles underground. A full description of the probe is given. Data collected from the probe has been used to compare the actual profiles with those predicted from a finite element analysis using laboratory measured thermal properties of the different rock types. This comparison indicates the applicability of laboratory measured parameters in modeling the real conditions. Factors such as applied pressure, moisture content and anisotropy on laboratory measurements is discussed.

Jan 1, 1983

The Golden Grove Project area is located 220 km (137 miles) east of Geraldton in Western Australia (Fig. 1). The project is a joint venture involving Amax Exploration (Australia) Inc. (Amax), Electrolytic Zinc Co. of Australasia Ltd. (EZ), and Esso Exploration & Production Australia Inc. (Esso), each with 31 116% interest, and Aztec Exploration Pty., Ltd. (Aztec), with a 3 1/2% carried and a 3% contributing interest. The venture covers two significant volcanogenic massive sulfide deposits and some 40 km (25 miles) of highly prospective Archean volcanics. During the course of the past 12 years (to 1983), all four companies were responsible for operating the project at one time or another and all influenced the discoveries. The Gossan Hill and Scuddles deposits are typical examples of volcanogenic massive sulfide deposits associated with Archean explosive submarine acid to intermediate volcanic complexes. They are located in the northwesterly trending Yalgoo greenstone belt of the West Australian Archean Shield. Gossan Hill, located in 1972, is essentially a copper deposit with minor zinc lenses; to date, 97 diamond holes have delineated a geological resource* estimated to contain 13 Mt (14.3 million st) of of 3.4% Cu and 13 g/t (0.38 oz per ton) Ag in the main lenses with minor lenses totaling 2 Mt (2.2 million st) of 3.7% Cu and 17 g/t (0.49 oz per ton) Ag and 1.7 Mt (1.9 million st) grading 1.5% Pb, 14% Zn, and 87 g/t (2.8 oz per ton) Ag. Scuddles is a zinc-copper deposit with gold and silver credits. It *Resource estimate provided by Esso for inclusion in Aztec Exploration Pty. Ltd. 1982 Annual Report was discovered in 1979 and, to the end of 198 1, had been delineated with 42 diamond holes. On the basis of this drilling, a geological resource* of 26 Mt (28.7 million st) has been estimated in three coalescing lenses. The lenses comprise 7.5 Mt (8.3 million st) of 2.1 % Cu, 12 g/t (0.35 oz per ton) Ag, and 0.3 g/t (0.009 oz per ton) Au; 7.6 Mt (8.4 million st) of 0.4% Cu, 9.9% Zn, 73 g/t (2.3 oz per ton) Ag, and 0.7 g/t (0.02 oz per ton) Au; and 1 1.0 Mt (1 2.1 mil lion st) of 1.1 % Cu, 9.3% Zn, 8 1 g/t (2.6 oz per ton) Ag, and 1.5 g/t (0.044 oz per ton) Au. Readers are referred to Frater (1978) and Harris et a). (1982) for a more detailed geological account of these deposits.

Jan 1, 1991

By Gino Vogt

In mechanized tunnelling operations performance, consumption and safety are main factors for jobsites. One of the most important components effecting these factors, especially in slurry TBM operations, are Slurry Treatment Plants (STPs). Inadequate/ suboptimally dimensioned and designed STPs create bottlenecks for tunnelling operation and jeopardize time schedules and performance. Inefficiently planned STPs could drastically increase consumption figures such as electrical power, bentonite, water and polymers, etc. Inaccurately selected and treated suspension properties can cause a high-risk potential for the whole job. This paper debates the relevant key parameters for STPs from start to finish of a project and its results in influencing factors from the manufacturer´s point of view.

Jun 13, 2021

By H. A. Taylor

Bismuth, one of the heavier chemical elements, is a pinkish metalloid that is chemically related to antimony. It is a byproduct of lead and tungsten extraction and, to a lesser extent, of copper and tin extraction. Antimony is a metalloid and less heavy chemical element, an extraction coproduct of metals such as lead, silver and gold. While both bismuth and antimony are metalloids, their major uses are as chemical compounds. The most frequently updated resources that always cover bismuth and antimony are the Bismuth Advocate News (BAN) and link at www.basicsmines/bismuth and the frequently updated Basics Mines Update blog at http://basicsmines-update.blogspot.com. The Bismuth wiki on Wikipedia also can be very helpful.

Jan 1, 2010

I was very interested in Professor Park's data on subsidence over longwall panels. His paragraph labeled "Conclusion," however, does not seem appropriate for the article. Nothing in the article gives any discussion of how knowledge of subsidence characteristics can be used in mine design to minimize damage. That thought may have been a reason for undertaking this study, but not a conclusion of it. From his article, I would conclude that subsidence movements last considerably longer at great depth. And the National Coal Board's subsidence prediction model represents this area reasonably accurately, though most literature claims their model predicts far greater disturbances than actually occur in most areas of the United States. Also, I would like to know, is the method used to determine angle of draw? The criterion used can make a significant difference in the value obtained. With 30 m (100 ft) spacing and a 122-m (400-ft) depth the angle between stations can be up to 14°.

Jan 1, 1989

By J. D. Megeath

In the October 1988 issue of MINING ENGINEERING, J.G. Wargo's paper discusses the problem of measuring and analyzing permeability, porosity, and fracturing in its relation to in situ leaching of disseminated gold deposits. This paper made me suspect that a good deal of information and analysis may have been done on this in reverse in the petroleum industry. Some years ago, I was involved with the US Geological Survey in a project studying the Devonian shale of the eastern United States. The Devonian shale contains gas deposits that have the characteristic of slowly seeping gas over a very long time period. To understand the rate of seepage, considerable study and analysis was done on the interrelationship of poros¬ity, permeability, and fracturing. The purpose was to find out how and why the gas could escape in the varying rates found in wells throughout the formation. It strikes me that this is the mirror image of the problem faced in attempting to understand how a cyanide solution will travel into a deposit. To possibly invent our own personal wheel a little faster, I would suggest a look at the work done on the Devonian shale. Some of it is contained in "Estimates of Unconventional Natural-Gas Resources of the Devonian Shale," US Geologi¬cal Survey Open-file Report 82-474, 1982, and "Additional Data for the Estimates of Unconventional Natural-Gas Re¬sources of the Devonian Shale," Open-file Report 83-676, 1983. It is entirely possible that some of this previous work could shorten the time required to make in situ leaching of dissemi¬nated gold deposits a profitable technique.

Jan 1, 1989

By R. C. Kirkman

Your interesting and well-written paper brings up the issue of the purpose or use of a mineral property appraisal, specifically the value of these evaluations when the quality and quantity of the mineral resource to be exploited have not been thoroughly investigated. I am not a practicing professional in regards to valuation of limestone investment opportunities. I simply wish to make a few generic observations about the appraisal process in order to stimulate meaningful thinking by appraisal professionals whose reports may be reviewed by professional investors and "laypersons" alike. It is my contention that the analysis given in your paper is very thorough, considering the data that was made available to you. But I would not like to be the person responsible for investment decision making without having a feel for the risk involved. Therefore, the reviewer must classify this type of analysis as relatively "subjective" because they have not received an indication of the inherent risk involved in exploiting a mineral resource. This risk can best be quantified by using probabilistic methods in conjunction with the quality and quantity of the mineral to be produced. Most appraisals passively ignore this problem. Specifically, you have accurately identified the various costs and values entering the economic appraisal process. These can usually be quantified with a great deal more certainty than the capability of the resource to provide 25 years of quality material. Also, in Cases A (West Virginia)and B (Alabama), you are fortunate enough to have previous operations data. What if there had never been production from these properties? How does a potential mineral property investor evaluate the resource capability to meet various projected financial outcomes without spending a good deal of up-front capital to drill and delineate enough quality resources for a 20-plus year operation. These questions pose a substantial risk to any potential mineral investor. Only probabilistic methods should be used to quantify this type of problem, short of drilling and metallurgical testing. I might be considered a "layperson," not being familiar

Jan 1, 1991

By J. W. Furlan

Due to the time consuming nature of froth testing in a laboratory environment, it is required, due to practical limitations, to develop a method of applying a single set of performance test data (Visintainer & Whitlock, 2012) obtained for a single froth pump at a given speed, to a range of froth pump speeds and sizes, % air contents, and liquid viscosities. Head, efficiency, and flow all vary as functions of both liquid viscosity and air content. As such, it is necessary to develop a technique which can be used to interpolate from existing test data in order to predict froth pump performance for pumps of various sizes running at variable speeds. Details of the technique developed in order to achieve this goal as well as the insights gained from analysis of the resulting regressions are discussed. Additionally, comparisons are made between the performance predictions of this test-derived method and those of the Hydraulic Institute Standard for the effects of liquid viscosity on centrifugal pump performance (ANSI/HI 9.6.7-2010).

Feb 27, 2013

By Madan M. Singh

With the current emphasis on ecology, safety, and conservation of natural resources, some consideration should be given to methods of mining that reduce surface damage, make the mining of coal less hazardous, and allow exploitation of a larger percentage of the coal in situ. One method that can be helpful toward attaining these objectives is the use of packing or stowing. Stowing involves the replacement of the ore that has been removed by waste material obtained from within the mine or elsewhere. Evidently, it would be most beneficial if this waste for packing were available from the mine being worked, but generally this is not possible. If complete stowing is adopted, it is necessary to bring in packing material from other sources. Stowing tends to reduce surface subsidence, but not eliminate it. It enhances roof support and curtails accumulation of methane in the gob, making the mining operations safer. It may also allow one to obtain a larger amount of coal. Currently, in the United States, a substantial amount of coal is left in place as pillars, in the hope that it will support the overburden indefinitely. Some of these could be extracted with stowing. The mining of thick, steep, or contiguous seams would also be facilitated.

Jan 1, 1974

By MUSTAFA ERKAYAOGLU, ENVER YILMAZ

Coal mining is likely to sustain its critical role as energy requirements are increasing. While surface mining exploits coal seams near the surface, underground mining techniques are crucial for extracting deep coal reserves. Longwall mining is one of the most common methods used in underground coal mining operations. This paper introduces a data-based framework — including data collection, data analysis and the interpretation of operational data — for understanding the system efficiency of a longwall shearer. Operational performance is evaluated by the time between arrivals (TBA) and duration of the shearer stoppages, shearer drums’ reversal time, cutting speed and flit speed on daily production in a longwall top coal caving (LTCC) mine. A discrete event simulation model is developed to represent the bidirectional cutting sequence of a longwall shearer.

By Ralph L. Merklin

One of the most commonly employed set of calculations in mill design and research is the material balance, known in wet beneficiation plants, as an Ore and Water Balance. For mill designers, the balance is one of the principal requirements in determining the proper size of launders, pipelines, process equipment, etc. In process development, one of the major goals is the establishment of an optimum balance. The usual procedure for calculating a material balance involves a manual technique utilizing reference tables, pre -obtained data, and a slide rule or desk calculator. With these, the engineer must perform a series of calculations which are repetitious in nature and time consuming. Figure I is the flowsheet of the grinding and flotation circuits for a copper concentrator. The initial ore and water balance was calculated manually and required approximately 24 manhours. Later, a number of changes were made in the balance, each of which required an average of 8 manhours.

Jan 1, 1967

By W. Wan

Diesel particulate matter (DPM) emitted from diesel engines is currently considered to be a health problem in underground mines. As a result, attempts have been made to control DPM both by reducing emission rates and by managing the DPM that gets into the mine atmosphere. This paper presents a method for modeling the generation, transfer and distribution of DPM in the mining sections through the use of a convection-based computer model so that controls for emitted DPM can be evaluated. A variety of ventilation strategies and diesel deployment schemes for room-and-pillar development sections were simulated to compare their effects on average DPM concentrations at several fixed and mobile personnel locations in the section. Input data for the model was gathered from actual diesel development sections and derived from experimental study results provided by other researchers. Studied using the model were ventilation schemes using vent tubing and brattice, exhaust location strategies on the vehicles, and the direction of ventilation at the feeder-breaker location. A summary of results from this study will be presented.

Jan 1, 1994

By Glenn Mongillo

Discrete Element Method (DEM) software has been successfully used to simulate various machine/soil interactions and provide insight for industries such as mining and bulk material processing. This paper will investigate typical calibration techniques used in particle models for DEM simulation and physical calibration experiments with soft ground TBM cutting tools to incorporate parameters such as tool drag forces that contribute to required TBM torque. With a well calibrated DEM model, it is expected that TBM simulation results will be more meaningful and provide better insight into TBM performance, power requirements, cutting tool placement, and overall cutter head design.

Jun 13, 2021

By Taner Aydogmus

The A$29 billion Chevron-operated Wheatstone Project is one of Australia’s largest resource projects. Located at Ashburton North, 12 kilometers west of Onslow in Western Australia, the project will consist of two Liquefied Natural Gas (LNG) trains with a combined capacity of 8.9 million tons per annum and a domestic gas plant. The LNG Plant will serve the offshore gas fields, which are situated some 250 km off the coast of Onslow in Western Australia. Once operational and on-stream, the Wheatstone Project will contribute to Australia becoming the world’s second largest exporter of LNG. For crossing the environmentally sensitive shore area, a micro-tunnel with an internal diameter of 2 m and approx. 1,242 m in length has been constructed by means of the pipe-jacking method. The micro-tunnel will accommodate a 1.1 m diameter pipeline (trunkline) to deliver gas from the offshore fields LNG Plant. The Wheatstone shore crossing design involves a number of unique challenges owing to its coastal location, where the alignment crosses through a shore area and terminates in a marine environment. This paper provides an overview of the Wheatstone Shore Crossing Project, presents the key features, and discusses the main aspects of the micro-tunneling design.

Jun 13, 2021

By Donald G. Rogich

The concept of initiating a large action-oriented contract, directed toward inherently safe mining systems, was conceived by the U. S. Bureau of Mines in January 1970. At that time we were in the process of establishing research contracts and grants, about 100 of which were let in FY 71 to deal individually with fairly specific technological areas. These projects in the aggregate covered a wide spectrum of health and safety problems. What appeared to be necessary was the creation of a project or program that would provide a focal point for the demonstration of many of the results of this research and also in the action sense culminate with working hardware and systems that could be tested and demonstrated over a fairly long teen. The concept of working demonstrable systems, rather than just a conceptual study, was, felt to be necessary for two significant reasons. In the development of any new system, the translation from concept to working hardware is usually a costly and time consuming process which acts as a deterrent to implementation. Secondly, many decisions in the mining community to change equipment or systems ,are based on first hand observation of the new system, in operational practice, an attitude which is certainly understandable in view of the high capital costs of equipment. The decision was made to procure a single R&D contract which would be aimed at developing underground coal mining systems which

Jan 1, 1972

By David H. Carlson

Mechanical sorting of "poor" rock accumulated from past native copper mining operations has been under study at the Michigan Tech's Institute of Mineral Research for several years. Prior to this work, the poor rock dumps totaling approximately 9 million tons containing an estimated 35-70 million pounds of copper (1) have been considered mainly as a local source of road aggregate used from time to time and consequently of minor value. An electro¬mechanical sorting machine developed by International Sorting Systems Corporation of Santa Barbara, California has been tested for preconcentration of the waste rock before conventional milling (2,3). The ISSC machine has possibilities for underground preconcentration of crushed mine-run native copper ores. The objective of the study described here was to provide information about limi¬tations on sortability due to characteristics of the ore and present crushing practices. When the native copper mines were in operation prior to termination in 1969, two types of ore were produced, amygdaloidal and conglomeritic. In the first type copper occurs in vesicles left by gas bubbles entrapped during rapid cooling of the tops of lava flows. The conglomeritic ore beds consist of rounded pebbles and fragments cemented together by calcite, epidote, chlorite, and feldspar; the copper occurs around pebbles, in cracks, and sometimes as partial or total re¬placements of pebbles. The copper in the conglomeritic ore usually is in finer grain sizes than that in the amygdaloidal ore, and large (plus 4 inch) copper masses are virtually absent.

Jan 1, 1970

By Giovanni Barla

The stress-relief method for the determination of the ground stress tensor is a common procedure in rock mechanics. In particular, the method of applying gauges to the end of a borehole is a well-established technique. Investigations, both experimental and theoretical, indicate that large discrepancies can exist in the determination of the ground stress tensor when the rock substance is not the ideal elastically isotropic material assumed for the reduction of data. The purpose of this paper is to extend the analysis of strain gauges applied to the end of a borehole to rock material more closely approximate to an orthotropic substance.

Jan 1, 1969

Despite two large projects represented in the keynote docket, the mood of the 2011 SME Arizona Conference was summed up best by Ferol Baker, general manager of New Mexico Copper Corp. (a wholly owned subsidiary of Themac Resources Group), ?In the past, it seemed like you couldn?t go to a conference like this without hearing about one big new greenfield project after another. Now what you see is companies doing internal expansion or small-scale brownfield development.? Overall, the tone of this year?s meeting, held at the J.W. Marriott Resort at Starr Pass in Tucson, AZ, was upbeat, yet practical. From the keynote and luncheon addresses to the six panels of sessions, the projects described were positive about the future, yet focused on the details required to make those projects come to fruition.

Jan 1, 2012

By Mohammad Ranjbar, Zahra Manafi, FAZAELIPOOR MOHAMMAD HASSAN, HAMGHAVANDI MOHAMMAD RANJBAR, Mahin Schaffie

Bioleaching has an increasingly important place among available mining technologies as biological processes have emerged as alternatives for metal recovery, especially for metals like gold and copper. An important disadvantage of bioleaching is the slow reaction rates, with microbial attack times often lasting weeks. Therefore, applicable research is required to improve these rates. From previous research, copper bioleaching has been divided into two specific regimes: (1) surface reaction controlling step and (2) mix of surface reaction and diffusion controlling steps. The presented model, which includes the effects of both these regimes, predicted the results of copper bioleaching recovery with good accuracy.

By J. J. McClellenand, R. A. Jankowski

Face ventilation and water sprays are the primary controls used on continuous miner sections to protect workers from respirable coal and silica (quartz) dust. Laboratory tests were conducted by the U.S. Bureau of Mines to determine the impact on respirable dust concentrations when increasing airflow from 3000 to 9000 cfm (1.42 to 4.25 m3/sec), water flow from 15 to 35 gpm (0.057 to 0.132 m3/min) , and water pressure from 80 to 200 psi (5.52 x105 to 1.38 x106 pa). The effective limits for each control and interactions between these controls were of particular interest. Initial analysis concentrated on defining the impact of the control parameters on the respirable fraction of the feed dust, which was a blend containing 90% coal and 10% quartz. Gravimetric sampling indicated that airflow had the most significant individual impact on respirable dust levels and resulted in reductions of 99% at the operator and 57% in the return. Regression modeling was used to predict dust concentrations at the operator and in the return. Significant interactions were observed between control parameters and often, defined the level for a control parameter where increases above that level did not significantly benefit dust control. Increasing airflow to 8400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.65 x105 Pa) typically provided respirable dust reductions at both sampling locations, while optimizing use of control resources. After determining these relationships for the total respirable fraction, selected filters were analyzed for quartz content to define the impact on the quartz component of the feed dust. For the individual control parameters, airflow again had the most significant impact and resulted in reductions of 98% at the operator and 26% in the return. Regression modeling of the quartz concentrations indicated that no significant interactions between control parameters were present. At the operators location, airflow was the only parameter identified as having a statistically significant reduction for quartz dust. A reduction in quartz approaching 95% was observed for increasing airflow to 6000 cfm (2.83 m3/sec). Increases above 6000 cfm had little additional impact. In the return, a linear relationship between control parameters and quartz levels was observed with reductions of approximately 27% predicted for increasing any one control parameter to its maximum level. The synergistic impact of increasing all control parameters to maximum levels resulted in a maximum predicted reduction of 81%.

Jan 1, 1991