Search Documents

By Walter Steiner, Claus Becker

INTRODUCTION General Switzerland is a densely populated country in the heart of Europe. With its total surface of 41.300 km2 and a population of 6,8 million in 1986 the average population density is 163 capita / km2. The population density is lower than in Germany (245 capita/ km2) or the Netherlands (355 capita/km2). The USA have a population density of 26 capita/ km 2. However, sixty percent of the Swiss surface is covered by the Alps and another ten percent by the Jura mountains the remaining thirty percent of the surface is covered by the Swiss plateau where the majority of the population lives. The population in the inhabitated areas is thus substantially higher and may possibly reach those in major metropolitain areas. Due to the high population density in Europe in general and Switzerland in particular future traffic demands cannot be fulfilled sole by car or plane. Environmental and land-use constraints lead to the third option for growing transportation needs: High-speed rail (Bovy, 1990). Switzerland has developed its own approach to promote public transportation and in particular rail transportation: "Rail 2000" (Stalder, 1990). The system "Rail 2000" is based on a series of hubs distributed over Switzerland where easy connections can be made.

Jan 1, 1991

By Robert A. Jankowski, J. Drew Potts

The Bureau has identified several ventilation techniques and a water spray application for reducing auger mining dust levels. The dust control methods all work by improving air quantity or flow patterns at the face. Section airflow is maximized by reducing air leakage between entries. Sealing stoppings with brushed- on mortar, containing fiberglass additives, reduces leakage. Heading airflow is maximized by properly installing the brattice curtain and keeping the area between the curtain and rib free from obstructions. The brattice curtains should be hung at least 1.7 m (5.5 ft) from the ribs in 7.9 m (26 ft) wide entries and kept less than 4.6 m (15 ft) from the face. A tight curtain seal is created by using the mine air pressure to force the curtain against the timbers, roof and floor of the mine. Using both a blowing curtain and an exhausting curtain will isolate some face workers from dusty air. The Bureau designed, auger clearer spray system, can be used to force heading air across the active face. Laboratory tests indicate that the auger clearer spray system can increase face velocities by more than 0.5 m/sec (100 ft/min), while using less than 0.13 l/sec (2.0 gal/min) of water.

Jan 1, 1989

By D. B. Sikka, R. B. Bhappu

Porphyry-type copper-molybdenum (Cu-Mo) deposits typically occur in the Phanerozoic rocks and have been well-documented. During the past two decades, a number of porphyry-type Cu-Mo deposits that range in age from 1055 Ma to 2970 Ma have been identified in the Precambrian rocks of Australia, Canada, China, Finland, India. Namibia and Zambia. The Malanjkhand porphyry copper deposit M.P., India is estimated to contain 789 Mt (870 million st) averaging 0.83% copper (mill headgrade); 0.004% molybdenum; 0.2 g/t (0.006 oz/st) gold; 6 g/t (0.175 oz/st) silver and a cap of 7.5 Mt (8.2 million st) of oxide ore averaging 0.8% copper. The economic potential of the expanded copper mining milling, smelting and refining complex is expected to yield cathode copper 118.6 kt (130,700 st); molybdic oxide 830 t (914 st); gold 1.9 t (61,732 oz); silver 46.6 t (1.5 million oz); sulfuric acid 240 kt (264,500 st), copper from leach dumps 11.5 kt (12,600 st); nickel 24 t (26,400 st); cobalt 84 t (92,600 st); bismuth 16 t (17.6 st); selenium 48 t (53 st), tellurium 4.8 t (5.3 st).

Jan 1, 1995

By Richard R. Klimpel

The purpose of this paper is to summarize some of the author's experiences in applying population balance models to a variety of industrial grinding circuits. Over 26 separate industrial circuits have been studied in detail during the last 10 years, each unique in its equipment type and layout as well as in the material (s) being ground. The success of the population balance approach during these studies was variable. Fourteen of the circuits were shown to be very amenable to such an approach while the remainder had conditions present that sufficiently violated the standard population balance assumptions so that the analysis was of less than optimal utility. Some discussion of the importance of standard population balance assumptions will be given. It is increasingly becoming this author's opinion that the use of population balance models has its greatest utility in defining logically and cheaply (in contrast to actual physical testing), the relative limits and comparisons of different proposed circuit configurations and changes in equipment types and/or operating conditions. As far as specific quantitative predictions and actual optimization of existing plant performance, the results of applying the population balance approach have been often disappointing and need to be coupled at the plant level with other engineering quantification techniques in order to achieve desired improvements.

Jan 1, 1992

By Craig J. Nelsen, J. Leroy Schutz

The Carache Canyon Prospect consists of a hypabyssal breccia pipe which intrudes a gently dipping sequence of Cretaceous Mancos Formation and Mesa Verde Group shales and sandstones. This sedimentary sequence is intruded by a number of Oligocene (34-30 Ma) calc- alkaline sills. The formation of the breccia pipe and its subsequent gold mineralization is related to the emplacement of an alkaline intrusive complex dated between 30-26 Ma. An exceptionally large block within the pipe provides compelling evidence that brecciated sills and sedimentary rocks form a relict stratigraphy that collapsed 400-800 ft (120-240 m) below their counterparts outside the pipe without substantial changes in stratigraphic position. Native gold and sulfide mineralization within and around the pipe occurs in fractures that are primarily controlled by competency differences between sills and sedimentary rocks and secondarily controlled by ductility contrasts between the relatively brittle Mancos Formation hornfels and the more ductile Menefee Group shales. The resulting pattern of gold mineralization is a series of stacked, tabular, mineralized sills and sandstone separated by barren shale in an annular region along the southwest margin of the pipe. A series of near-vertical, subparallel, sill and sandstone breccias separated by barren or weakly mineralized shale breccia occur within shallow levels of the pipe.

Jan 1, 1990

By K. A. Natarajan

Platinum electrodes are not inert as originally thought to be. The reactivity of platinum electrodes can explain their erratic behavior in many electrochemical measurements of metallurgical interest, e.g., in flotation systems, streaming potential measurements, contact-angle measurements, and in leaching systems. The anomalous behavior of platinum electrodes in redox potential measurements in aqueous systems was studied through Eh and pH measurements in water-oxygen, iron-water-oxygen and manganese-water-oxygen systems. Stability relations between Fe++ and Fe(OH)3 and between Fe(OH)2 and Fe(OH)3 were studied to judge the correspondence between experimental and theoretical equilibrium lines. The practicality of redox potential measurements in estimating ferric-ferrous ratios in aqueous systems was investigated along with their suitability as indicators in leaching operations, e.g., the removal of iron by aeration from manganese leach solutions.

Jan 1, 1970

By J. Edberg

"This article details the use of an alternative testing method to the 2004 "Post-Tensioning Institute (PTI) Recommendations for Prestressed Rock and Soil Anchors" manual’s recommendations for temporary and permanent rock anchors for applications in shafts and tunnels. This method was developed and used for the Black River Tunnel (BRT) project in Lorain, OH as a means to reduce testing time of rock bolts during shaft construction while maintaining a similar level of quality control and assurance. The following sections will detail the project background, subsurface characteristics, shaft construction, the 2004 PTI testing method and associated difficulties, the alternative testing method and conclusions reached.Project backgroundThe city of Lorain is located in north central Ohio on the south shore of Lake Erie, approximately 40 km (25 miles) west of Cleveland and 119 km (74 miles) east of Toledo. The city chose to build a large-diameter storage tunnel and pump station to meet its requirements to reduce sanitary sewer overflows to the nearby Black River. NTH Consultants Ltd. (NTH) was retained by the city’s prime consultant, Malcolm Pirnie Inc. (now the water division of Arcadis), to perform a geotechnical investigation, develop design and construction bid documents for the tunnel and shaft liner systems and ultimately provide oversight assistance during the construction phase of the project.The BRT is an approximately 1,700-m (5,560-ft) long, 7-m (23-ft) diameter rock tunnel to be lined with a 5.8-m (19-ft) inside diameter secondary concrete lining (Fig. 1). The tunnel is designed to accept flow at a new drop shaft (Shaft 3) located on the west side of the Black River, across from the city of Lorain Black River waste water treatment plant (BRWWTP). The tunnel will be dewatered at the south end by a large diameter pump station (Shaft 1) located in the existing Lorain Port Authority Public Boat Launch. Flow from the new pump station will be discharged into an existing shallow interceptor sewer and directed back to the BRWWTP."

Jan 1, 2014

By S. Chander

A review of the published literature on the mechanism of depression of sulfide minerals shows that a unified theory is not yet available. The various mechanisms that have been postulated include competition between depressants and collectors to adsorb at the surface sites, creation of thermodynamic conditions nonconducive for formation of a metal collector salt or formation of a hydrophilic coating on the surface. The hydrophilic coating may or matt not effect the adsorption of collectors. In yet another mechanism, the depressant nay participate directly in oxidation/reduction reactions between collectors and sulfide minerals. Examples from the literature are discussed to highlight oxidation/reduction effects in the depression of sulfide minerals.

Jan 1, 1984

By W. C. Shanks

The Pioche District of Lincoln County in southeastern Nevada (Figures 1 and 2) has been an historically important producer of silver, zinc, and lead. Economic geology of districts in the Pioche area is summarized most adequately in recent reports by Tschanz and Pampeyan (1) and Gemmill (2) and only a few major aspects will be discussed here. Production in the Pioche District began in 1869 and early mining concentrated on silver-bearing fissures in lower Cambrian quartzites. In the early 1870's the Pioche District was second only to the Comstock Lode in world silver production (3). More recent mining activities have centered on the other major ore type in the area, bedded replacement of lower Cambrian carbonates by Ag-Zn-Pb sulfide ore. Production of replacement ore peaked around 1950. The present study is focused on the Pan American Mine because it is an excellent example of low grade carbonate replacement deposits, because there is little structural dismemberment, and because access was readily available. Most previous workers have suggested that both the fissure vein deposits and the bedded replacement deposits of the Pioche districts are a result of spatially related Laramide igneous activity. The purpose of this study is to determine whether ore genesis is a result of igneous activity or if mineralization might be related to late diagenetic processes such as formed Mississippi Valley "type" deposits. Stable isotopes of sulfur, carbon, and oxygen in ore and gangue minerals have been studied to determine the probable isotopic composition of the ore fluid and paleomagnetic studies of the carbonate rocks have been utilized to determine timing of mineralization. Additionally, petrographic and field studies of carbonate lithologies were undertaken in an attempt to delineate non-structural controls on ore localization. These studies are still proceeding and the results presented herein are, therefore, preliminary in nature.

Jan 1, 1979

By Ryan P. Sullivan, Ben D. DiFiore, Robert J. Auber, Michael A. Piepenburg, Lisa M. Smiley

Pollution to Lake Erie will be significantly reduced by the Westerly Storage Tunnel (WST) system, which is mainly comprised of a 10,000-ft long tunnel and a dewatering pump station in the downstream tunnel shaft. Separate construction contracts for the tunnel and pump station required careful management of the interface risks. A key decision was to decouple the projects by relocating the mining shaft away from the pump station. The need to receive the tunnel boring machine (TBM) in the pump station shaft was eliminated by dismantling the 28-ft diameter TBM in the tunnel then carrying it back through the tunnel and up the mining shaft. This paper discusses how interface risks were successfully managed during design and construction to limit overall schedule impacts.

Dec 1, 2022

By Richard Giffen, Martha Gross, Luca Pellegrini, Pa Ousman Njie

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in Virginia includes parallel 1.5- mile (2.4 km) tunnels constructed using a tunnel boring machine (TBM). The TBM launching and receiving shafts were excavated within the footprint of two reclaimed islands abutting the navigation channel for the Port of Virginia. The shaft excavations—a circular tri-cell shaft at South Island, and a circular-rectangular twin-cell shaft at North Island—were supported by slurry walls up to 190 feet (58 meters) below the island surfaces. This paper describes specic design considerations for these shafts, as well as construction and uality-oversight aspects of their excavation and construction.

Jun 23, 2024

By Jaeheon Lee, Junmo Ahn, Jiajia Wu

To reduce the environmental footprint of hydrometallurgical processing of black mass from spent lithium-ion batteries (LIBs), a green leaching system based on glycine and sodium metabisulfite (Gly-SMS) was proposed. The leaching study demonstrated that the highest cobalt and lithium recoveries of 100 percent and 99.8 percent were achieved under optimal conditions. The leaching mechanism revealed that the dissolution of LiCoO2 in the Gly-SMS solution followed the shrinking core model. The apparent activation energies for cobalt and lithium were determined as 48.05 and 41.51 kJ/mol, respectively, indicating a surface chemical reaction controlling mechanism. The leachate was then processed by an acidification- precipitation technique with oxalic acid as the precipitant to remove cobalt. Glycine complexes with metal ions by zwitterionic ligand and recycles in the leaching-precipitation circuit, reducing the reagent cost. Compared to other studies, this leaching system has near-neutral operating conditions and is cost-effective, making it an economically viable alternative for treating cathode materials from spent LIBs.

Dec 1, 2024

By S. K. Mishra

The history of the Australian coal industry is almost as old as the history of Australia after new settlement. The first cargo of coal was exported from Newcastle to India in 1799. Although coal has been mined in Australia for almost two centuries, there are indications that the first coal was processed in 1877 in the New-castle area, nearly a half-century after the first coal processing in Europe. Processing on any significant scale began only in 1944 at the Newcastle Steel Works. In Queensland, however, coal processing did not begin until the second quarter of this century. The well-known dramatic growth of mining and processing of Australian coal since the mid-sixties has primarily been due to the expansion of the export market in Japan and other Asian and European countries. Black coal occurs in most of the major sedimentary basins in Australia. The better known deposits of commercial importance are in Sydney, Bowen, Oakland and Gailiee Basins (Figure 1). Apart from Collie Basin in Western Australia, other coal deposits of the Arckinga Basin in South Australia, the Bonaparte Basin in Northern Territory and Tasmania Basin, Tasmania, are basically unexploited. Sydney Basin of New South Wales and Bowen Basin of Queensland remain the major producers of black coal in Australia.

Jan 1, 1985

I found the article most interesting and timely. I consider it imperative that mine case studies like this one are undertaken and published so that the practicing mining engineer and geologist can obtain a better idea of what is the preferred estimation and grade control technique to use, given the site-specific geology, grade distribution, etc. Mining companies, with operating gold mines, need to be encouraged to either initiate such a study in-house or support a research project by financing a graduate student at a local university. The latter method is preferable since it not only provides research support but also an excellent training opportunity for young mining engineers and geologists. Ideally, what is needed is exploration drill-hole, blasthole, and mine production data that can then be used to assess the efficiency of different estimation and grade control methods by comparing the results obtained using the drill/blasthole data with the actual production data. It is hoped that more mining companies will realize that the rewards from this kind of research greatly outweigh the sometimes perceived problem with releasing data to a university. I noticed that the authors used the blasthole data to represent the actual values, the validity of which relies heavily on the two key assumptions with regards to blasthole assays and in-pit ore-waste selection procedures. Could the authors comment in more detail on these assumptions and what criteria they used to check the validity of the assumptions? Since the article was published, have the authors had the opportunity to compare their estimates with the actual production data? It would be interesting to compare other estimation methods with OK and IK. For example, how well did the polygonal method used at the mine compare with the results given in the paper? I would like to mention that B.L. Kwa completed a similar study (Kwa and Mousset-Jones, 1986) using exploration drill-hole, blasthole, and production data from the Alligator Ridge mine in Nevada. The study compared a variety of estimation methods, including IK, and the final results are shown in Fig. 1. The IK method exhibits the smallest difference between estimated and production results and is closely followed by the indicator moving window (Ind MW) method. Reply by Y.C. Kim We do concur with Professor Mousset-Jones with respect to the merit of such case studies performed at a local university. In answer to his request for comment on the validity of the two key assumptions made in our paper, we can only say that these are reasonable assumptions that are very difficult to validate. The assumption of blasthole assays being accurate can be partially validated by a careful analysis of the nugget component of blasthole variograms. The assumption that the in-pit ore-waste selection procedure in use was an effective one can only be validated through comparison between the mine estimates of ounces of gold versus the actual recovered ounces of gold at the mill. Neither one of these two assumptions has been validated to date due to several reasons. For example, the mine went through a change in management since the study. Similarly, no compelling reasons have been presented to perform detailed variogram analysis of the blasthole data. We do, however, believe that the obtained results (i.e., indicator kriging performs better than OK in a highly skewed deposit) will remain the same in relative terms, regardless of how valid these two assumptions may be. The most recent com¬parative study by D. S. Lindsey of the Montana College of Mineral Science and Technology also shows a similar ranking between ordinary kriging versus probability kriging, which is an extended version of indicator kriging.

Jan 1, 1987

By William Gleason

"While the American Exploration & Mining Association (AEMA) was preparing to close one chapter and begin another during its annual conference in Spokane, WA Dec. 3-7, word of a significant victory on an issue that has been important to the association for many years came from the halls of Washington, D.C.During a keynote address on Dec. 6, Joe Balash, assistant secretary of Land and Minerals Management for the U.S. Department of the Interior (DOI), told a sold-out lunch crowd that the DOI had released final drafts of proposed revisions to the Obama-era greater sage grouse conservation plans. The revisions suggest removing hundreds of thousands of acres of federally protected habitat in Utah, and easing restrictions on energy development and other activities, including mining, in Colorado, Idaho and Wyoming.The protections of the sage grouse were put in place by the Obama administration in 2015. The sage grouse, a prairie fowl, is considered by conservationists to be a key indicator species for the health of America’s sagebrush ecosystem. The previous plan to protect the ground-dwelling bird imposed restrictions to development in sage grouse habitat, but did not place the birds on the endangered species list — a move that many believed would have imposed far more rigid rules.AEMA, and its executive director Laura Skaer, led the way in the fight against the Obama-era greater sage grouse plan, arguing that the plan unnecessarily hurt economic development.“We were the first organization to point out that the greater sage grouse was being used to stop mining, oil and gas production and grazing on public lands in the interior mountain west,” said Skaer who is retiring from AEMA with a significant legal win on this front. “Early on, we cautioned that the proposed Land Use Plan Amendments would be worse than a listing (of the sage grouse) under the Endangered Species Act. Very few believed us until they saw the plans with all of the restrictions and the recommendation for a 4-million-ha (10-million-acre) withdrawal from mineral entry. We were the only organization that filed comments on all 88 Land Use Plan Amendments in 11 states covering more than 24.2 million ha (60 million acres).”"

Feb 1, 2019

By Robert J. Greaves

High-resolution seismic reflection profiling can be used to evaluate detailed struc¬tural and stratigraphic features of coal pros¬pects. Since most coal prospects are relatively shallow (less than six hundred meters deep), the vertical and lateral resolution of seismic data can be significantly improved by high sampling rates in space and time. The case study present¬ed shows the effective use of seismic data in evaluation of the Wyodak coal at a prospective coal gasification site. The data were used to map the detailed structure and thickness of the coal and to search for lateral discontinuities, such as pinchouts and. faults. An important find was a paleochannel cutting across the base of the coal seam, which was later confirmed by drilling.

Jan 1, 1983

Nearly as impressive as the machines that will be on display at MINExpo are the massive engines and tires that keep the machines moving. As you can imagine, it takes a special tire and special engine to run these machines. The following is a look at some of the exhibitors that will be at MINExpo displaying engines and tires. Cummins Inc. Cummins Inc. will display a lineup engines from 37kW to 2,983 kW (49 hp to 4000 hp) at MINExpo, representing the most extensive ?smallest to largest? range the company has ever put on display.

Jan 1, 2012

By Hugh W. Evans

Many reports and papers have been delivered on projects under construction or already in operation, but we believe there are few that have been written about projects yet to be built specifically dealing with advanced mine and environmental planning. This paper describes such planning for Atlantic Richfield Company's Black Thunder mine. Project planning is a cyclic phenomenom involving four broadly overlapping planning steps (Figure 1). The demands of the public include needs that can be satisfied through planned resource development. Using a base of information that partly exists and must in part be gathered and updated, the preplanned development can be, evaluated. The evaluation process, with built-in environmental constraints leads to an implementation procedure. Implementation results in the development, including the release of the affected area to other public demands that follow.

Jan 1, 1975

By J. H. Tu

The technical paper correctly points out that the kriging variance is not a good measure of the uncertainty of the estimated (i.e., kriged) value of individual blocks. The authors claim that their proposed jack-knife method, which is a rekriging of each block by eliminating, in turn, one sample from m the original sample set and then taking the average of the rekriged estimates, not only gives good block estimates, but the resulting jackknife kriging standard deviation is a useful indicator of the "true uncertainty associated with block estimates." However, they immediately abandon the idea of using the block-by-block standard deviations, reasoning that these standard deviations are not independent and that there is no easy way to utilize them. There may be another reason for not using them. The jackknife standard deviations for individual blocks given in their example are mostly in the range of 0.004 to 0.005 oz/st (0.14 to 0.17 g/t) with only one block having a high value of 0.012 oz/st (0.41 g/ t). These individual block standard deviations are as low as the jackknife standard deviation for the mean grade of the entire shape, i.e., 0.0041 oz/st (0.14 g/t). Do they represent the "true uncertainty" .of the individual block estimates? Could the authors explain this? In a global shape consisting of a large number of blocks, any given sample will affect the kriged estimate of only those few blocks within its vicinity. This is the rationale for the authors' selective rekriging, making the jackknife algorithm more efficient. On second thought, why not do away with jackknifing altogether? Just cumulate and normalize, if necessary, the kriging weights of each sample used during the ordinary block kriging process, and then compute the global variance from these kriging weights and their respective sample grades? After all, isn't the global mean grade nothing but the weighted average of the samples used in the estimation? Reply by G.S. Adisoma and M.G. Hester The jackknife is one of the many tools in a practitioner's toolbox to solve estimation problems. The strengths of the technique lies in its simplicity, i.e., it uses the concept of mean and standard deviation and the fact that it can be easily combined with other tools, in this case kriging. Because the jackknife kriging (JK) estimate is also the mean of the pseudovalues, the JK standard deviation is attractive just as the standard deviation of the mean explains the variability of the data. The difference is that the pseudovalue calculation in jackknife kriging uses the ordinary kriging (OK) weighting scheme instead of simple arithmetic averaging. The data used to illustrate the jackknife technique in the paper con¬sist of high values that are roughly three times the low values. The resulting JK estimate of the block grades show that the highest estimate is roughly twice the grade of the lowest estimate. The contrast between the low and the high estimate is more evident in the JK estimate than in the OK estimate, even though the mean grades of the blocks for the two estimates are very similar. Nonetheless, in this paper, we are concentrating more on the need for a more realistic measure of uncertainty, or precision, for the estimate. Unlike its OK counterpart, the JK standard deviation of the blocks clearly reflects the original data variation. The highest JK standard deviation of the blocks is three times its lowest value. This follows our intuition that, when the samples used to estimate a block is more variable, the resulting estimation variance (or standard deviation) should be higher than the case where the samples are more uniformly valued. However, block-by-block standard deviation or variance is of little practical value in reserve estimation and classification, as well as in mine planning. One is usually more interested in quantifying not the variance of the individual block estimate, but the uncertainties associated with a much larger dimension, such as the minable reserve. Thus, the thrust of the paper is to find a simple way to obtain a single estimation variance or standard deviation associated with the reserve grade estimate. The discussion by J.H. Tu did not mention how one would obtain the global variance from the OK weights and the sample grades. As a technique that offers a data value-based measure of uncertainty for its estimate, the "leave-one-out" jackknife fills this need nicely through the block kriging shortcut approach described in the paper. Note: The first column and the last two columns of Table 3 in the paper should have contained a single number each, namely, an OK estimate of 0.0317, a JK estimate of 0.0333 and a JK standard deviation of 0.0041 oz/st, respectively, for the shape, as are obvious from the text.

Jan 1, 1997

By R. T. Hukki

The paper describes a two-stage industrial hydraulic classification system including hydrocyclones for primary classification and newly developed cone classifiers for secondary classification. Performance data based on large scale grinding and classification tests are presented.

Jan 1, 1981