Search Documents

By William E. Lamont

The Mineral Resources Institute (MRI) of the School of Mines and Energy Development (SOMED), University of Alabama conducted studies to determine the potential for upgrading the Eastern Devonian shales by flotation. Results of those studies indicate that flotation concentrates containing 150 liters of oil/t (36 gal/t) can be produced from shale containing 50 liters of oil/t (12 gal/t) as determined by Fischer Assay with good recovery of the kerogen. Organic carbon and trace elements such as molybdenum, vanadium and uranium also are concentrated with the kerogen. Kerogen concentration was found to be a function of the size of grind.

Jan 1, 1983

By Stephen Njoloma, William Bracken, Harald Cordes, Ivan Hee

"DC Water’s First Street Tunnel (FST) is part of the $2.6 billion Clean Rivers Project designed to reduce the occurrence of combined sewer overflows into local waterways. Due to flood events in the Bloomingdale and LeDroit Park neighborhoods, the FST Project was accelerated by DC Water to mitigate future flooding by boosting storage capacity and thus relieving the undersized combined sewers.The FST Project was finalized in 2016 as a collaborative effort between DC Water, its consulting team consisting of Greeley & Hansen and McMillen Jacobs Associates, and the design-build team of Skanska, Jay Dee Contractors (SKJD) with WSP Parsons Brinckerhoff as the designer.Scope of project. The FST Project (Fig. 1) included four primary shaft sites, a large 6 m (20 ft) internal diameter, 823- m (2,700-ft) long bored tunnel and three adit connections from the off-line shafts to the large-diameter tunnel. The adits which vary in size and length, are the subject of this article. The Channing Street site (Fig. 2) was established as the main site for an Earth pressure balance tunnel boring machine (TBM) and included a 49-m (160-ft) deep shaft with slurry wall support of excavation and 20-m (65-ft) internal diameter final cast-in-place permanent concrete liner. The construction sites at Adams Street, V Street and Thomas Street each consisted of off-line shaft structures tied to near-surface sewer diversion chambers and ventilation facilities. These three off-line shafts were connected to the large bored TBM tunnel via adit tunnels. Each of the three adits had a portion or the entire length excavated by sequential excavation method (SEM) in frozen ground.The Adams Street adit (Fig. 3) was constructed in two phases. The first phase is the 23-m (75-ft) long and 5-m (16-ft) diameter section immediately outside the drop shaft which also serves as the deaeration chamber and was excavated by SEM. The second phase which is 91 m (300 ft) long and 3 m (10 ft) in diameter was excavated by Micro TBM (MTBM) launched from within the permanently lined deaeration chamber. MTBM excavation commenced toward a reception chamber that was excavated by SEM from the previously bored FST TBM tunnel. This SEM excavation had a 5 m (17 ft) diameter and a length of 4.5 m (15 ft)"

Jan 3, 2018

By M. R. Yalamanchili

Recently, noequilbrium electrokinetic measurements using laser-Doppler electrophoresis were reported by Miller et al. (1992) for alkali halides and the sign of their surface charge thus determined. These results are generally as expected from simplified lattice ion hydration theory with KCI, under normal circumstances, being the most significant exception. In this regard, lattice defects (F centers and oxygen imperfections) have been found to influence the surface charge of KCI and its electrophoretic mobility. In particular, the presence of oxygen defect states in the crystal lattice has been found to be responsible for KCI's unexpected behavior. The concentration of oxygen defect states in KCI, as characterized by UV/Vis absorption, was varied in order to study their influence on the electrokinetic behavior and subsequently on the flotation response of KCl. At low oxygen contents « 60 ppm) KCI is positively charged as expected from lattice ion hydration theory. However, typically, KCI contains substantial oxygen (>300 ppm) sufficient to impart a negative surface charge which accounts for the selective flotation of KCI from NaCl by hetero-coagulation with oppositely charged alkyl amine hydrochloride collector colloids.

Jan 1, 1994

By B. W. Stunkard

Hibbing Taconite Company is located by the cities of Hibbing and chisholm near the center of the Mesabi Range, approximately 169 km (105 miles) from the Canadian Border. The plant site is equidistant from these two communities, about 6.4 km (4 miles) from each. A 169 km (105 mile) railroad connects us with the port of Superior, Wisconsin, where the pellet production is loaded into lake carriers for lower lakes destinations. Immediately to the south of the mine area is the world famous Hull- Rust-Mahoning Mine which produced more than 700 000 000 million tons of red ore between the years 1893 and 1973.

Jan 1, 1979

By C. Hanson

Two modes of potential loss of oxime extractants in liquid extraction processes for the extraction of copper have been studied. In loss "by chemical degradation, two mechanisms of acid hydrolysis are possible, some reagents degrade primarily in the organic bulk phase, Others at the interface between the organic phase-- phase protects the oxime but salts added to the aqueous acid phase can promote the rate of degradation. The reagents reported on are the LIX series (Henkel Cpn), SME529 (Shell Chem.Co.) and P5100 (Acorga) Loss by organic entrainment in the aqueous phase leaving mixer-settlers has also been studied, parameters investigated including impeller/tank geometry and the phase inlet arrangements. The consequences of extractant loss by the above mechanisms...are commented upon. They include the direct economic cost, the possible environmental problems and the implications for downstream operations such, as electrowinning.

Jan 1, 1980

By Frank E. Sullivan

The separation of liquids from granular materials has been widely studied by a number of: investigators over a period of years in an effort to more fully understand the physical phenomenon which occurs. Liquid may be removed from solids, or partially removed, by gravity separation, mechanical separation' or heat drying. Mechanical separation is advantageous when compared to heat drying principally from a cost saving standpoint and also on certain materials which are heat sensitive. It is realized however that mechanical separation of liquids has certain practical limitations. In order to evaluate the efficiency of mechanical separation and predict the extent of, liquid removal, it is first necessary to study the forces which hold the liquid to the solids. From a very practical observation using gravity drainage, it is soon obvious that a pile of coarse solids will drain faster and retain less liquid than a pile of finely divided solids of the same material. For commercial operations it is important to estimate the residual liquid which will remain after a mechanical separation. Batel (1) explored the various quantities of liquid present in the interstices of the bulk granular material. From his work and other authors which he has correlated in one of his recent papers, various formulas are now available which permit an empirical relationship to be developed showing residual moisture versus mechanical separating forces.

Jan 1, 1965

By R. J. Weigel

The Santa Fe Railway serves the dominant U. S. potash producing region which is centered at Carlsbad, NM. This rail system extends over 12,000 miles stretching from Chicago to the Texas Gulf Coast to the state of California. (see Figure 1) Since Carlsbad mining operations began in the 1930?s, Santa Fe has been transporting potash to many of the important grain producing areas of the country and to the major ports in Texas and California. Santa Fe has maintained a close relationship with the potash companies and has adopted a marketing philosophy of attempting to maximize opportunities for the Carlsbad producers where it is mutually beneficial. Potash has been an important commodity for the Santa Fe. It accounted for 8% of our revenue in 1965 and 3% in 1984. In the 1950?s, Carlsbad became the second largest revenue producing point on the Santa Fe. But this prominent position has diminished as ore reserves became depleted, imports flooded the U. S. market, and truck transportation developed.

Jan 1, 1985

By Charles H. McGuirk

The Port of Conneaut, the largest bulk material handling and storage facility on the Great Lakes, is using the latest electronic and visual testing devices to augment and enhance its well established computerized preventive maintenance system. The results of this comprehensive program have been impressive. The remaining life of components can be accurately forcast, and replacement can be programmed around operations, resulting in a significant improvement in system availability and reduced costs for the dock operator and its customers.

Jan 1, 1983

By William B. Schmidt

In July of 1974 a study team comprised of the authors was formed by the Department of the Interior. It was supported in part by funding from the National Science Foundation. The purpose of this study group was to visit coal mines and research and manufacturing facilities in England and Germany, to review the status of mining in these countries, and to identify mining technology which might have application to U. S. mining conditions. The duration of the visit was 18 days. The first week of the trip was spent in England. Time does not permit a complete recitation of the team's impressions but a few of the more interesting technologic developments will be discussed. These fall into the following categories- High Speed Development Ground Support Chainless Haulage and Face Conveyors Nucleonic Steering of Shearers Miscellaneous

Jan 1, 1975

By R. J. Weege

Conventional underground mapping methods and diamond drilling are being applied in a study to determine the nature of the copper ore occurrences near the footwall of the Osceola lava flow top, commonly referred to as the Osceola Amygdaloid. Our work to date suggests that structures formed by relatively impermeable barriers, created by flowage and injection of still-molten lava from the interior of the flow into the solidified, brecciated crust, acted as the ore receptacles. Ascending hydrothermal fluids traveling near the footwall contact were trapped and confined in these barriers which retarded the direct upward movement of the ore fluids and caused deposition of copper. Oreshoots located near the footwall appear to have been formed spatially' independently from the hanging-wall oreshoots by fluids traveling simultaneously, but along different channelways. The barrier concept as advanced by earlier writers to explain the concentration of the ore-bearing, fluids into broad shoots con¬stituting entire ore bodies is found to be equally as applicable for the localization of smaller oreshoots within the Osceola ore body.

Jan 1, 1962

By W. D. Hausel

The Wyoming Province is an Archean craton which underlies portions of Idaho, Montana, Nevada, Utah, and much of Wyoming. The cratonic block consists of Archean age granite-gneiss with interspersed greenstone belts and related supracrustal terranes exposed in the cores of several Laramide uplifts. Resources found in the Province and in the adjacent accreted Proterozoic terrane include banded iron formation, Au, Pt, Pd, W, Sn, Cr, Ni, Zn, Cu, and diamonds. The Province shows many similarities to the mineral-rich cratons of the Canadian shield, the Rhodesian and Transvaal cratons of southern Africa, and the Pilbara and Yilgarn blocks of Western Australia, where much of the world's precious and strategic metal and gemstone resources are located.

Jan 1, 1991

By V. Rajaram

The oil shales located in the Appalachian Basin cover an eight-state area of the eastern U. S., and are referred to as Devonian (black) shales. These shales have been exploited for their gas potential for several years. The Institute of Gas Technology (IGT) has conducted research since 1972 on the production of shale oil from the Devonian shales, and this resulted in the development of the HYTORT process. This process demonstrated that the yield from the Eastern oil shales can be greater than the value indicated by the Fischer assay method. IGT estimates that 423 billion barrels (67.3 x 109 m3) of oil could be recoverd by HYTORT processing of surface-minable eastern U. S. shales. Recently American Syncrude Corporation and Southern Pacific Petroleum N. L. have proposed oil shale projects in Kentucky. This paper will describe the surface mining and retorting techniques that have been studied for exploitation of the Devonian shales, and enumerate the problems that have to be overcome before commercial production can be realized from these shales.

Jan 1, 1983

By XUEWEN WANG, Changda Zhang, Huaguang Wang, Mingyu Wang, Bin Hu

The copper smelting process produces plenty of copper slag every year, which is a hazardous solid waste, but a secondary resource. In the present study, the extraction of copper, nickel, and cobalt from copper slag was investigated through the process of sulfation roasting–water leaching and the process of sulfation roasting–sulfate decomposition roasting–water leaching respectively. Compared with the process of sulfation roasting–water leaching, the process of sulfation roasting–sulfate decomposition roasting–water leaching is a better choice, which could not only get almost the same leaching of copper, nickel, and cobalt as the former process, but has a lower leaching of iron and aluminum. For the process of sulfation roasting–sulfate decomposition roasting–water leaching, the leaching of Cu, Ni, and Co reached up to 74.2%, 71.1%, and 69.6% respectively, under the optimal conditions including sulfation roasted with 80 wt% sulfuric acid addition at 200 °C for 60 min and sulfate decomposition roasted at 650 °C for 60 min, followed by water leached at 90 °C for 30min with a liquid–solid ratio of 2 ml/g. The leaching of Fe and Al was only 4.9% and 17.6%.

May 4, 2020

The 2012 North American Tunneling (NAT) conference is expected to attract more than 800 tunneling and underground construction professionals. But don?t let the North American part of the meeting?s title fool you. Many of the attendees will come from all over the world. The meeting is scheduled for June 24-27 at the JW Marriott Indianapolis Hotel in Indianapolis, IN. In addition to two and a half days of technical programming, the accompanying exhibit has attracted 116 exhibitors in 140 booths. And the conference will include short courses, a field trip and plenty of social activities that will give attendees the opportunity to catch up with each other.

Jan 1, 2012

By Yashar Pourrahimian, Magreth S. Dotto

Fragmentation by blasting is a critical process in hard rock mining. The blasting process and outcomes are highly influenced by rock mass properties and their response to higher stresses and loading rates. Each rock mass is unique, but some features affect the blast energy similarly, leading to similar outcomes. Having analyzed these features and their influence on blast results, they can be incorporated into the blast design to achieve better outcomes. This paper presents a numerical model validated by a case study from the actual mine blasts that studied the effect of rock mass properties on explosive energy production, attenuations, and overall blast outcomes. The results show that when the model parameters are calibrated based on real data, they can be used to simulate the fragmentation process and therefore be used to aid blast design.

Jun 25, 2023

By Ali Soofastaei

Mining operations are increasingly data-rich yet decisionconstrained. Fragmented systems, variability in geology and operations, and sustainability obligations create multiobjective trade-offs that classic analytics cannot reconcile at operational tempo. This paper proposes an end-to-end framework that fuses digital transformation practices (governed data platform, semantic layer, feature store, and MLOps) with generative AI (retrieval-augmented generation, tool-use, and agentic workflows) and decision intelligence (simulation/digital twins and multi-objective optimization). We formalize sustainability-aware objectives, define a practical stack and governance controls, and demonstrate how an AI “decision copilot” can surface options, quantify trade-offs, and document rationale. Two figures illustrate a production-grade architecture and a Pareto frontier for cost–emissions trade-offs; two tables operationalize decision-domain mapping and a transformation maturity rubric. The approach is product- and company-agnostic.

Feb 22, 2026

By R. S. C. Rogers

The present study examines the use of two vs. one stage of hydrocyclones in a pilot scale ball mill circuit. The approach used for doing this is based on computer simulation with mathematical models that explicitly account for the grinding mill/classification system interaction. Parameters for the ball mill model are obtained using a short-lived radioactive tracer method in open circuit tests of the study mill. The hydrocyclone model, based on the size selectivity concept, is developed and validated in standalone testing of the study hydrocyclones. Simulation procedures are validated through actual tests of the closed circuit grinding configurations of interest. Results of the evaluation indicate that two stages of hydrocyclones in the study circuit would improve classification, increase productivity and lead to more closely sized circuit products when compared to the conventional one stage hydrocyclone circuit. A computer simulation approach for comparing these circuit configurations in larger scale grinding circuits is also suggested.

Jan 1, 1981

By P. H. S. W. Kulatilake

The presence of discontinuities strongly affects the mechanical and hydraulic behavior of rock masses. Joint geometry networks play a vital role in civil, mining, and petroleum engineering projects associated with jointed rock. The need for a realistic representation of joint geometry in rock masses has been recognized. The first part of the paper shows how to build three-dimensional stochastic joint network schemes and also shows how to perform validation studies for these schemes using joint data from the Stripa mine, Sweden. Due to the existence of complex joint patterns, mechanical behavior of jointed rock masses usually exhibit scale effects and an-isotropic properties. A correct understanding of the mechanical properties (strength and deformability) of jointed rock masses is important for designing and performance estimation of structures build in and on rock masses. Beyond a certain volume, the mass proper-ties of the rock may remain essentially constant with respect to the effect of joints. This minimum volume may be used as the element size to represent the equivalent properties of a statistically homogeneous rock mass volume which contains a significant number of joints. This volume may be termed as a "Representative Elementary Volume" (REV) and may be of great importance for engineering purposes. Investigations are underway at both the 2D and 3D levels to look into the possibility of establishing relationships between REV mechanical properties and joint geometry parameters. Recently developed joint geometry modeling schemes are linked with existing distinct element codes (both 2D and 3D) to create a stochastic/deterministic stress analysis approach in achieving the goal. Results obtained so far in this direction are presented in the second part of the paper.

Jan 1, 1992

By Richard M. Chamberlin

Perlite is an altered rhyolitic glass with 2 to 5 wt % water that expands or "pops" when heated quickly to plasticity while evolving steam to form lightweight, glass foam. Commercial perlite deposits in New Mexico are well-developed zones of chemical weathering (hydration) superimposed on highly permeable and thick glassy zones at the chilled upper surface and toes of high-silica-rhyolite lava flows and lava domes. The maximum tonnage of glass in these volcanoes was predetermined by their unique eruptive histories. New Mexico perlite production (80% of US production of 571,00 st) is mostly from the 3.9 Ma high-silica-rhyolite lava flows at the No Agua Peaks volcanic center. The primary vent at No Agua is defined by a 900 ft-high rubidium-rich composite lava dome, known as West Peak, that contains minor perlite reserves. Slightly less rubidium-rich lava squeezed out from under the west flank of the dome to form relatively thin (250 ft) but highly vesicular lobate flows that now consist of about 50 % recoverable perlite. Finally, rubidium-poor lavas were extruded from a radial dike on the northeast flank of the dome. These thicker (400 ft) flow lobes contain about 20 % recoverable perlite. The largest mass of lava does not always contain the most perlite. The thinner (west) flow at No Agua yields the largest perlite reserves rather than the large composite lava dome or thicker (east) flow.

Jan 1, 1994

By Melvin W. Jackson

The study of the excavation of large spherical cavities in salt formations first became of interest in 1958 when it was recognized that a large cavity could be of value in the study of the detection or concealment of underground nuclear explosions. Previously unpublished studies are reported in this paper and other studies reviewed relating to the excavation of large cavities in salt by mining ad by solution. Special emphasis is placed on the utilization of the Tatum salt dome (about 22 miles southwest of Hattiesburg, Mississippi) for the proposed site of a large excavated cavity. The U. S. Atomic Energy Commission has recently been studying such a cavity as Project Payette, but no details have yet been published. If Project Payette is determined feasible and work funded, it would eventually involve the firing of a nuclear explosive at the center of a large cavity.

Jan 1, 1969