Search Documents

By Robert Stefanko

13.1-SUBSIDENCE AND GROUND MOVEMENT ROBERT STEFANKO 13.1.1-SUBSIDENCE AND FAILURE This treatment of subsidence and ground movement will be confined to subsidence control for limiting surface damage by assessing the significant parameters affecting ground movements during mining to optimize mining techniques. The material will be equally applicable to evaporite mining as well as coal but will not deal with block caving or similar systems where failure is deliberately induced and surface protection is not necessary or provided. When an underground opening is established, the original equilibrium is disturbed with resultant stress concentrations. While many factors are involved in opening stability, the span (W) undoubtedly is one of the most important factors in failure. Assuming it is relatively small, the overlying rock strata can bridge across the opening and little if any movement or convergence of top and bottom will occur. However, as the span increases, a point is reached where the stress in the overlying rock strata exceeds some strength value of the rock, and the top breaks. If the opening span is limited to some subcritical value (-We) and/or is at great depth (D), a pseudo-arch will form, achielring stability before rupture occurs to the surface. The boundary of this arch is thought to approximate an ellipse in form with the major axis vertical and equal to four times W, although there has been little field research to substantiate this theory. However, if the width of this opening is increased at this horizon to some critical value (W,) or the same span is created in a shallower seam, the overlying strata ill progressively rupture to the surface and the characteristic subsidence trough is formed (Fig. 13-1) The area of the surface affected is much greater than the area of the seam extracted, depending on the "angle of draw" (a), which is the angle between a vertical line from the edge of the opening and another line extended to a point at which subsidence tails out to zero. This angle has been found to be about 35° in Europe but is rather academic, being a function of instrument precision in detecting subsidence. Since the subsidence effect is so small at any point beyond n 25° angle, this latter may be considered the practical limit of subsidence. Further- more, indications are that the angle of draw varies with depth and nature of the strata.' In a field study over a 1,000-ft-deep potash mine in New Mexico, the maximum angle of draw was found to be 51.5°.2 So far, only a single opening has been considered. However, the width of the excavation applies to any complex mining system of entries, rooms and longwalls as long as the seam has been fully extracted and the width represents the distance from one solid rib to another. It will be noted that the amount of vertical displacement varies from point to point on the surface (s), but the maximum subsidence for a given trough occurs at the center (S). This latter value may not he equal to the maximum possible subsidence (Sm) which occurs only if a critical or super- critical (+W,) width has been exceeded (Fig. 13-1). Substantial surface damage can result when subsidence occurs. Factors affecting the amount and type of ground movement are: thickness and properties of the seam, angle of draw, width of excavation, depth and type of overburden, inclinations of strata and surface, and the amount of support left in the gob. In Europe,

Jan 1, 1973

By R. Raby

During the 1980 decade, the rapid price increase for flake graphite has generated a high degree of interest for the discovery and the development of alternate occidental sources of supply in response to fluctuations in quality and availability from current producers. Alike many industrial minerals, graphite draws its complexity not only from its mineralogy and unique properties but also from the very large spectrum of industrial applications each calling for specific quality criterion. As new high technology uses are being developed, more rigid specifications will apply. Discovered during the latter part of 1988 by Mazarin inc., some 30 Km South of Fermont near the Quebec-Labrador border, the Lac Knife deposit was quickly identified as one of the world major long term alternate source of stable supply for this mineral. This paper also reviews the status of the project development as of late 1991, while updating previous papers published by Industrial Minerals1990 and Mining Magazine 1990.

Jan 1, 1992

By Frank R. Field, Joel Clark, Walter C. Labys, William A. Vogely

Mineral models provide a systematic and comprehensive approach for analyzing and fore- casting the behavior of mineral markets and industries.' They also permit the analysis of a wide range of policy decisions. Obviously such models cannot capture all of the intricate relationships that shape the behavior of a mineral market. However, such models have become extremely useful and in many cases support the decision making approach of judgmental analysts. They tend to narrow the range of likely outcomes and thus reduce the risks and uncertainties of investing, trading, and speculating in minerals. Mineral models provide not only answers to "what-if" questions, they also inform analysts of the benefits and costs associated with mineral investment decisions. More recently they have been applied to specific mineral issues of the possible impact of buffer stock stabilization schemes and of import supply restrictions. Mineral Models Defined Because mineral models are so diverse, we must begin with a fairly broad definition. A mineral model is a formal representation of a mineral market, industry or system where the behavioral relationships included reflect the underlying economic and engineering factors as well as the political and social institutions. Of ten, but not always, a mineral model will consist of some combination of the following components: demand, supply, inventories and prices. Modeling of demand behavior normally begins with an interpretation of basic demand responses to prices and income (i.e., the associated price and income elasticities). Price elasticities vary among different minerals and among their diverse uses. They tend to be lower for minerals without close substitutes than for those where such substitutes exist. In addition, these elasticities vary with time as well as with the actual excess demand or excess supply. Variations like these, coupled with the relative instability of prices for a number of minerals, make explanations of demand behavior difficult. The degree to which demand responds to changes in income depends on the income elasticity of the end products to which the minerals serve as inputs. Those products with a relatively low income elasticity tend to experience proportionally smaller swings in sales than those with higher elasticities. The transmission of demand cycles to minerals producers comes through a series of stage-of-process effects. Demand measurement also is influenced considerably by mineral substitution patterns. The cross-price elasticity of a competitive or complementary commodity also varies with minerals, markets, and time. Where minerals easily substitute for one another, as in the case of cop- per and aluminum in electrical conductor applications, cross-price elasticities are relatively high. Modeling of mineral supply behavior normally involves consideration of resource development, economic conditions, geologic

Jan 1, 1985

By Richard O. Y. Breese

Geologically and commercially, the term diatomite is applied to the nearly pure sedimentarv accumulation of diatom frustules- the microscopic skeletons of unicellular aquatic algae belonging to the class of golden brown algae, bacillariophyceae. The sediments are fine-grained, siliceous, and consist primarily of amorphous opaline silica with only minor amounts of organic residue, secondary minerals, and co-deposited non-diatomaceous or crystalline clastic debris. In the geological sense, the name diatomite implies sedimentary accumulations that have reached appreciable thickness and when thick enough, such accumulations consequently may have possible commercial potential. Although the term diatomite is popularly and inappropriately applied to any sediment in which there is an abundance of diatom frustules, alternative terminology is more correctly employed to describe the less pure diatomaceous sediments, for example: clay-bearing diatomite or diatom-bearing clay. Synonyms in current usage include diatomaceous earth and kieselghur. More antiquated and obsolete terminology includes tripoli-powder, tripolite, and infusorial earth. Worldwide, diatomites occur within Tertiary to Recent lacus- trine and marine sedimentary facies. Although diatomite is wide- spread throughout the world, deposits that contain high purity, commercially versatile ore are uncommon. Physical properties of the diatom and of processed diatomite that provide unique commercial value in a broad spectrum of market end-uses include ornate fine structure, low bulk density, and high porosity and surface area. Properties of equal importance are mild abrasiveness, high absorptive capacity, insulating ability, relative inertness, and high brightness. End-use markets are diverse and range from insulating brick and absorbents through quality sensitive filter aids and premium quality functional fillers. Notwithstanding both the economic attractiveness of the specialty markets and the commercial versatility of the high purity deposits, deposits of lesser purity are mined in nearly all parts of the world for less demanding uses. Mining costs are minimized through open pit quarrying, but in Europe, Asia, Africa, and South America underground mining methods are also employed. Blasting is not required because diatomite is soft and easily broken loose with mechanized equipment. Following gentle crushing, the ore is dried, milled, and processed into one of three broad categories of products: naturally milled, straight calcined, and flux calcined grades. Each of these principal categories is further subdivided into additional grades through particle size adjustment of the powders. Agglomeration of particles, alteration of fine structure, and color change are achieved through calcination. Flux calcination further accentuates these changes. Production throughout the world is dominated by the United States, followed by Romania, the former Soviet republics, and France. Other major producers include Spain, Mexico, Iceland, Korea, Japan, and Germany. Denmark is a major producer of Moler earth products, which consist of a diatomite-clay mixture. HISTORICAL BACKGROUND The first industrial use of diatomite can be traced back some 2000 years to the Greeks and to the use of diatomaceous earth as a component in lightweight building brick and in ceramic pottery. It was not until the mid-1800s, however, that the unique properties of diatomite were first recognized and the market end-uses explored and developed. One of the most important of the early uses followed the development of dynamite by Alfred Nobel in the mid-1860s, whereupon diatomite was used as a component of the explosive to improve stability and safety. Other early uses included low temperature insulating and refractory bricks and as a component in insulating and fireproofing construction panels. During the 1920s, processing technology underwent a very rapid evolution with the development of calcination, flux calcination, and air classification technologies. Through these technologies, innumerable different size and grade classifications could be made for market applications and for rapidly diversified end- uses. Today, the application of processed diatomite for filter aid is the largest of the quality sensitive end-uses. Specific filtration uses include the clarification of beer, wine and liquor, vegetable oil, syrup and sugar, pharmaceuticals, and swimming pool water, to name a few. As a functional filler and extender, processed diatomite is ideally suited for application in paint, rubber, and plastic formulations. Other filler applications include use as an anti-blocking agent in plastic film, anti-caking agent for fertilizer, thermal insulating material, catalyst carrier, polish, abrasive, pesticide and fertilizer carrier, and chromatographic supports. Throughout much of the world diatomite is still used as a component of insulating brick and as an absorbent.

Jan 1, 1994

By G. J. C. Young

In 1986 the city of Johannesburg celebrates its first century of existence. The fact that the city was founded to exploit the gold deposits which underlaid it, prompts this review of the gold process development in the mining industry of South Africa. Clearly a complete history of, the gold recovery process to date is not called for and it is proposed therefore to outline the most significant developments which have taken place since the middle 1930's, that is to say the last 50 years or so. Prior to this period the industry had seen the development of comminution processes employing cone crushing in closed circuit with vibrating screens followed by grinding in rotating mills and the gradual disappearance of stamp mills. The all sliming process was well established as a viable route and continuous dewatering in thickeners, continuous leaching and filtration were serious rivals for the earlier batch processes. Continuous processes for gravity concentration had also been developed and the recovery of gold from pregnant solutions employed cementation on zinc dust as opposed to shavings. Thus at the beginning of the half century under review the industry had adopted, or started to adopt, many of the processes still accepted as modern practice. However in some areas little change was evident this was especially so in the smelthouse where some thirty more years were to elapse before the hand stoked coal fired calcine and reverbatory furnaces were replaced by more environmentally acceptable electric furnaces. The most significant feature in recent history has been the mining of progressively lower grades of ore and the retreatment of tailings from earlier operations, much of the latter comprising tailings only a decade or even less in age. Notable among these operations are those on the East Rand near Springs in the Transvaal, in the Orange Free State at Welkom and more recently, massive reclamation of tailings close to the city centre itself. The carbon in pulp (CIP) process has been much publicised in recent years and all new plants erected during the 1980's have adopted this route for gold recovery. However the major proportion of tonnage milled in the industry is still subjected to the more traditional process of liquid solids separation by vacuum filtration. The discussion that follows will centre largely on the developments in the traditional process route, which for the sake of completeness is listed below: Comminution Dewatering Leaching Liquid solids separation Gold recovery Smelting

Jan 1, 1985

By R. Woods, J. D. Wright

INTRODUCTION The Endako deposit was first explored in 1926, but development waited until the early nineteen sixties. It first came under the control of Placer Development in 1963, and early in 1964 a decision to bring it into production was reached. The deposit is located near the geographic center of British Columbia, and is served by an east-west communication system including a paved highway, mainline railway and good telephone, teletype, and computer facilities. The plant area is shown in Figure 1. The operation is known as the Endako Mines Division of Canex Placer Limited of Vancouver. First production was achieved in June, 1965, at a nominal rate of 10,000 tons per day, but it soon was closer to 15,000 tons per day. In 1967, two new grinding and flotation sections brought capacity to the present rate of approximately 27,000 tons per day. With mill heads of around 0.15 percent MoS2, production is about 14,000,000 pounds of molybdenum per year. A flowsheet of the operation is given in Figure 2. A legend for this flowsheet is given in Table 1. Published ore reserves are estimated at 214,500,000 tons at an average grade of 0.143 percent MoS2. PRIMARY CRUSHING The 85 or 100-ton haulage trucks dump over a grizzly into a 42 inch x 65 inch C.A.C. (Canadian Allis Chalmers) gyratory crusher.

Jan 1, 1976

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research recently developed a series of models using computational fluid dynamics (CFD) to study the gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models using Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side of the continuous miner; 100 percent of the discharge redirected back toward the face, but divided equally to both sides of the machine; and 15 percent of the discharge redirected toward the face on the off-curtain side of the machine, with 85 percent directed into the return. These models were compared against a model with a conventional scrubber discharge, where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100 percent redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner, which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.

Jan 1, 2015

By Elimame Elaloui, Kais Elghniji, Constantin Virlan, Aurel Pui, Chaima Ouled Amor

Separation and identification of minerals composing the Tunisian silica sands have been conducted by acid etching and hot filtration/sedimentation (HFS) without affecting the quartz component. It was found that the hot acid etching process is an effective method to separate quartz and clay minerals in the silica sand. The SEM micrographs of the silica sand show rough surface and some cracks with irregular shapes. The surface becomes clean and smooth after acid etching process. After chemical dissolution, the clay minerals were recovered by hot filtration following by sedimentation at low temperature. FT-IR, EDS maps, and secondary electron (SE) analyses of separated clay minerals reveal the presence of Fe2O3, montmorillonite, and kaolinite minerals. The LIBS analysis of clay minerals shows the presence of Al, Fe, Ca, Al, and Mg. The sequential etching process can be introduced in the purification methods as an effective way to separate quartz from clay minerals.

Jul 29, 2020

By A. L. de Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS). Biologically produced hydrogen sulfide has economically very interesting application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

By E. A. Schmidt

The Thompson Creek molybdenum deposit is located in the Bayhorse mining district about 20 air miles southwest from Challis, Idaho. Cyprus Mines Corporation began exploration on the property in 1968, and at present is in the pre-production stripping phase. Molybdenum mineralization is contained in a late Cretaceous (88 m.y.), composite, biotite granodiorite-quartz monzonite intrusive complex. The complex intruded carbonaceous argillites, causing local silicification and hornfelsing of the sedimentary rocks. The main portion of the orebody is unconformably overlain by up to 1000 ft of Challis volcanic rocks (49 m.y.). Surface mineralization and related rock alteration can be recognized over a 2500- x 8000-ft area extending northwesterly from the discovery outcrop. Molybdenite occurs in a network of subparallel quartz-biotite-muscovite-orthoclase veins and veinlets within the intrusive rocks. The zone of +0.020/0 Mo mineralization outlines a steeply dipping tabular configuration in the main orebody and gradually changes into a hood-shaped configuration along strike to the northwest. The overall grade [ ] of the deposit is controlled by the abundance of the quartz- molybdenite veins and veinlets in the intrusive rock. Very little disseminated mineralization is present, and no economic mineralization occurs in the argillaceous sedimentary rocks. Muscovite, biotite, and orthoclase/microcline define three alteration zones that conform with the overall zone of mineralization. The upper alteration zone contains dominantly muscovite and sericite associated with quartz veins. The central zone contains coarse biotite and locally orthoclase and microcline. Molybdenite is most abundant within this zone. The lower zone contains thin envelopes of orthoclase/microcline around quartz veins. Based on about 313,000 ft of drilling and 8592 ft of underground development work, computer-derived ore reserve calculations indicate 200 million tons averaging 0.1 1% Mo at a 0.050/0 Mo cutoff grade with a waste to ore stripping ratio of about 3:l.

Jan 1, 2013

By Yuexin Han, Yanjun Li, Peng Gao, Yongsheng Sun, Qiang Zhang

The non-isothermal magnetization roasting process and isothermal magnetization roasting process of siderite ore were investigated using thermogravimetric (TG) analysis and a real-time infrared gas analyzer. X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) were used to analyze the characteristics of samples. The results showed that the decomposition degree and decomposition rate of siderite ore were vitally affected by heating rate and roasting temperature. It was determined that A1 reaction model (f(α) = 1 − α) and A3/2 reaction model (f(α) = (3/2)(1 − α)[−ln(1 − α)]1/2) were the most probable mechanism function of the non-isothermal decomposition process and isothermal decomposition process, respectively. The phase transformation and decomposition mechanism during the roasting process were evaluated. Siderite decomposed in the process of magnetization roasting, released CO and CO2, and transformed into strongly magnetic magnetite. The SEM images highlighted that as the decomposition progressed, the structure of roasted samples was destroyed, and an increasing number of cracks and pores emerged on the surface, which is advantageous to the following grinding process.

Mar 26, 2021

By Chester O. Ensign

The White Pine Mine is situated in the southwestern portion of the Keweenaw Peninsula of Upper Michigan approximately 6 miles south of Lake Superior (Fig. 1). It is east of the Porcupine Mountains in Ontonagon County. The ore deposit is about 70 miles southwest of the famous native copper deposits of the "Copper Country" lying northeast of Houghton. Geological conditions are different at every mine and create a special set of problems in dilution control. This paper is largely intended to describe the techniques applied in mine dilution control (grade control) at White Pine, and present results of the program. For necessary background information major geologic characteristics of the deposit, particularly those that exert control over the distribution of ore, are briefly discussed. Mining methods are described in considerable detail since applied grade control techniques are adapted to these.

Jan 1, 1964

By K. E. Hjelmstad

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air, rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine, fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage.

Jan 1, 1989

By R. N. Chakravorty

Spontaneous combustion presents a very serious hazard to both safety and economics of mining operations. Notwithstanding considerable research that has been done over the years to present and control spontaneous combustion the risk still exists. Consequently, this problem poses a major challenge to mine safety researchers; new and improved techniques are constantly being developed to deal with this major hazard. This paper reviews the current practices to prevent and control spontaneous combustion in coal mine operations highlighting new developments in this area. Research and development work presently being carried out in Canada to' deal with this problem is also discussed which includes monitoring, inertization and application of biotechnology.

Jan 1, 1988

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of x-ray backscatter, iron Ka fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1992

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk, either at the commissioning of a concentrator or at the point of implementing an improvement to an existing concentrator operation. High-confidence flotation testing (HCFT) was developed for this purpose and is part of the list of technologies at various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of research on this methodology at Xstrata Process Support, Sudbury, several improvements to the HCFT method and complementary connections between sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified. Key words: Flotation testing, Flotation

Jan 1, 2010

By Theodore S. Jordan

The discovery of a major porphyry-type copper deposit on the Papago Indian Reservation in Pinal County, Arizona was announced by El Paso Natural Gas Company in 1968. The deposit, known as the Lakeshore Property, contained an estimated 470 million tons of sulfides and oxides averaging 0.75 percent copper. History and Geology of the area have been described by Harper and Reynolds (1969). El Paso subsequently&apos; entered into the agreement for joint development of the property with Hecla Mining Company, with Hecla as the operator. The ore body consisted of three types of mineralization: 1) Disseminated Oxide Ore, <1% Cu 2) Disseminated Sulfide Ore, <1% Cu 3) Tactite Ore, >1% Cu

Jan 1, 1985

By Ashraf A. M. A. Wali

Many of the economic resources of Egypt have been recognized and exploited for thousands of years (e.g. gold and copper). Most of these minerals, particularly those from hard-rock sited deposits, are found in complex form along with other components while those present in sedimentary sequences are largely in simple compounds or as native elements. Recognition of their characteristic settings (structure, basin development, environment of formation etc.) is the main clue in predicting and locating their presence. The main economic minerals exploited in Egypt today come from sedimentary sequences and include sodium and potassium chlorides, gypsum, sulfur, and sedimentary iron ores. Large amounts of low grade sedimentary phosphates are known but are not of economic value at today&apos;s prices. Recent intensive investigation in the north-eastern Sinai (EI Arish) and along the southern coasts of the Gulf of Suez has revealed new and extensive sulfur and chloride deposits, and considerable oil and gas are now being exploited from closely related sediments. Tin is the only mineral that is produced from hard-rock sources, and gold and copper deposits are present but not of high enough grade to be economically viable. However, a significant part of Egypt has not yet been studied in enough detail to close the door on future discoveries. Another point of considerable geological interest is the presence of diverse, modern evaporitic settings, from which we may draw the analogs for many of the older gypsum, anhydrite, chloride and sulfur de-posits. In fact these analogs are so well displayed that both the Sinai and Gulf of Suez-Red Sea evaporites (Middle and Upper Miocene) can be readily compared with these modern deposits.

Jan 1, 1990

By K. A. Natarajan, M. R. Sabari Prakasan

"Biodegradation of sodium isopropyl xanthate using two types of bacterial strains, Paenibacillus polymyxa and Pseudomonas putida, is demonstrated. At concentrations higher than 50 mg/L, the presence of xanthate in the growth medium resulted in bacterial toxicity, retarding growth kinetics. Adaptation through serial subculturing in the presence of higher xanthate concentrations resulted in the development of xanthate-tolerant bacterial strains. Stress proteins secreted by bacterial cells grown in the presence of xanthate were isolated. Bacterial cells could utilize xanthate as a growth substrate, degrading xanthate species in the process. Acidic metabolic products generated by bacterial metabolism promoted efficient xanthate decomposition. Probable mechanisms for the biodegradation of isopropyl xanthate are illustrated.IntroductionDifferent types of alkyl xanthates (ethyl, isopropyl, amyl, etc.) have been used as flotation collectors in the concentration of sulfidic ores for several decades. Large quantities of waste water and xanthate-containing effluents are generated by ore flotation processes, posing considerable environmental challenges. Billions of cubic meters of such process waste waters are produced annually across the world, most of which are discharged to the environment, often without any treatment. Leakages and accidental release of xanthate reagents from manufacturing plants and during transportation and storage can also contaminate the environment. Residual concentrations of xanthate reagents are encountered in waste effluent, which are found to be toxic to aquatic life and unfit for human consumption (Harris, 1984; Okibe and Johnson, 2002). Further, direct recycling of such waste waters for plant operations can compromise water quality standards required for process operations. The presence of residual xanthate in recycled waters from flotation plants deleteriously influences flotation processes. Xanthate can be easily decomposed at low pH values; however, CS2, which is more toxic, will be produced by the acidification of neutral and mildly alkaline xanthate-containing solutions. Physico-chemical methods such as flocculation, chemical oxidation and decomposition and physical adsorption used to remove residual collector reagents from mill process waters are often expensive and not environment-friendly (Oliveira and Rubio, 2009; Cheng et al., 2012; Molina et al., 2013,)."

Jan 1, 2015

By G. Purcell

When coal in an oil/water slurry is ground to minus-200-mesh in a ball mill, some of the mill energy, normally wasted as heat, can be usefully recovered to help emulsify the oil. If the discharge flows onto a suitable sized trommel screen, water and ash material are rejected through the screen while coal and oil ball together to give a clean coal product. A small (6-lb/hr) continuous plant has demonstrated the feasibility and the limitations of this process for New Mexico coals.

Jan 1, 1980