Search Documents

By M. Sears, W. H. Su, J. Wickline, M. A. Van Dyke, G. Esterhuizen, Z. Khademian

It is commonly recognized that seismicity can be induced by rock failures or slip along geologic structures around mining excavations. The unpredictable nature of these events and their proximity to the working area may raise safety concerns in underground mining operations. Modeling can be a useful tool for estimating seismic potential for a given mine layout, but the challenge is to detect a seismic event and estimate its intensity in the model. One well-documented approach is to monitor the variation in the energy content of the model and record potentially damaging seismic events when there is a significant release of energy. Researchers from the National Institute for Occupational Safety and Health (NIOSH) employed this approach using 3DEC modeling software to simulate the anomalous seismic events that occurred in a deep longwall mine in Virginia in 2005. A four-panel model of the mine was constructed utilizing a 2D cross section at the location of the mining face at the time of the event. Seismic potentials associated with the development of each panel are evaluated by recording the seismic energy released during the simulation. The results demonstrate the occurrence of two relatively significant events during the mining of the last panel, which are consistent with the historical observations at the mine.

Apr 26, 2022

By M. A. Schimmelpfennig, A. D. S. Gillies

M.J. McPherson Having worked on the thermodynamics of air/liquid-water mixtures passing through the surface fans of deep mines, I find this paper of great interest and congratulate the authors on producing it. There are two matters, however, deserving discussion. First, the authors have described the classical theory of fog formation with fogging occurring at "supersaturation." In fact, the process of fog formation begins well below 100% humidity. The more strongly hygroscopic nuclei in the atmosphere will attract water molecules and begin to grow at a relative humidity perhaps as low as 70%. The process is a dynamic one with both condensation and evaporation taking place throughout the mixture on microscopic liquid surfaces. As saturation is approached, the rate of condensation accelerates rapidly producing the familiar reduction in visibility. Hygroscopic nuclei are present in all natural atmospheres and under the appropriate conditions of pressure and temperature, will produce clean fogs. However, if the air is polluted by particulates from combustion or other processes then the resultant coagulation with growing liquid particles may produce dense (and sometimes photochemical) smogs. It is this process that is likely to occur in underground mines when moist air is cooled below dew point. Second, the authors have summarized very well the individual measures that might alleviate the problem. In particular, I agree that neither heating nor refrigerating the air, by themselves, provides a satisfactory solution. However, there is a combination of these that provides a neat and effective control of fog formation. This involves a small, self-contained refrigeration unit within a duct but without the usual external heat rejection facility. The air is cooled below dew point and, hence, dehumidified on passing over the cold evaporator coils. The heat from the condenser is rejected back into the air downstream from the water eliminator, as shown in Fig. 1. The duct configuration can be designed to create good mixing at the outlet. I have used a climatic simulation program to illustrate the effect, assuming a 500-m (1,640 ft) long airway of cross section 60 m2 (645 sq ft), an airflow of 9 m3/s (318 cu ft per sec), inlet conditions of 19/19.25°C (66/67°F) wet bulb/dry bulb temperatures, a virgin rock temperature of 17°C (63°F) and typical rock thermal properties for a hard-rock mine. I have also assumed that 10% of the rock surface is wet. Figure 2 shows the variation in temperatures along the airway if no measures are taken. The relative humidity remains close to 100% and condensation will occur throughout the length of the airway. Before any such installation is designed, the exercise must, of course, be repeated for each location with accurate data. However, this example demonstrates the potential of the system. The idea is not new - the principle is sometimes used in air-conditioning plants for buildings. Figure 3 shows the effect of removing 30 kw of heat by evaporator coils sited 40 m (131 ft) along the airway and rejecting that heat (plus another 10 kw of compressor and fan power) into the air at 60 m (197 ft). Condensate water is produced, at a rate of 0.45 L/min (0.12 gpm). The result of this sequential cooling/dehumidification/heating process is to separate the wet and dry bulb temperatures along the length of the airway. The relative humidity increases from 80% at the duct outlet to 92% at 500 m (1,640 ft). The airway is maintained free from fog.

Jan 11, 1983

By Jon Y. Kaneshiro, Eric Dawson, Pooyan Asadollahi, Steven Hunt

This paper provides updates to the paper published by the lead author at RETC 2011 with a summary of developments in technologies, products, and approaches to corrosion analyses of gravity sewer tunnels and microtunnels. This paper presents approaches in evaluating degradation of reinforced concrete liners. Also, the carbon footprint of conventional concrete liners and alternative “green” liners are compared and their life cycle costs are considered. A few case histories from the past decade are provided indicating the latest and emerging trends in liner protection.

Jun 13, 2023

By Kenneth Deaton

"A packaged cooling system is being developed for refuge alternatives (RAs) that will meet U.S. Mine Safety and Health Administration (MSHA) qualification guidelines for deployment in coal mines. This system will allow full occupancy ratings of deployed refuge alternatives to be maintained by keeping the apparent temperature inside the RA from exceeding 35° C (95° F).Research investigations sponsored by the National Institute for Occupational Safety and Health (NIOSH) have shown that heat buildup caused by occupants in mobile RAs will result in apparent temperatures that exceed the 35° C (95°F) limit established in 30 CFR 7.504.Figure 1 shows the temperature rise in an inflatable RA having an occupancy rating of 23 people at an 27° C (81°F) mine air temperature. This plot shows the need for either heat mitigation or occupancy derating in warmer mines.The Refuge Alternative Environmental Control System (RAECS) will be designed to provide enough heat mitigation to eliminate occupancy derating due to heat buildup over the 96-hour refuge period.This article describes testing of a prototype cooling system that uses proven vapor compression technology powered by batteries to keep the RA interior below the 35° C (95° F) limit for a minimum of 96 hours. Testing of this prototype cooling system was conducted in December of 2015 and January of 2016 at the NIOSH test mine in Bruceton, PA. December testing was conducted at the prevailing mine ambient temperature — approximately 15.5° C (60° F). The January testing was done with the mine ambient temperature in the immediate vicinity of the RA artificially elevated to 29° C (85° F). Realistic heat gain from RA occupants was provided by human simulators developed by NIOSH. These simulators add sensible heat corresponding to human metabolic processes and latent heat generated by respiration and perspiration. Heat generated by CO2 scrubbers was also added. Results of cooling system performance using these simulated loads at the two ambient conditions are described. A comparison of the apparent temperature in the RA using two different control techniques is also presented. This work documents the ability of the cooling system to meet the established apparent temperature limit at the full occupancy rating of a six person RA. A new cooling system intended for use with existing RA deployments and having greater cooling capacity is currently in development and will be described.Expendable desiccant modules were also used to provide supplemental water vapor removal and their role in mitigating cooling load is addressed."

Dec 1, 2016

By A. Noble

"In coal and mineral processing, several numeric parameters are used to quantify the separation performance of unit operations. For density-based separations, the partition curve is used as the starting point for many stages of diagnostic analyses. The curve is often quantified by its midpoint slope sharpness, and this single value is subsequently used for technical evaluation, benchmarking, and comparison. While this analytical approach does depict misplacement by relative density class, it inherently prioritizes middling separation and does not consider process economics or the micro-price value of individual classes. An alternative parameter, the organic efficiency, does indirectly consider process economics, but it does not reveal information on the root cause of lost revenue or misplacement. In this paper, a new analytical approach, the partition moment of inertia, is introduced. This parameter reconciles the technical misplacement data derived from the partition curve with the economic data derived from micro-pricing. The result is a new analytical procedure that promises better use of performance data. IntroductionPartition curves are commonly used in the characterization, evaluation and simulation of various physical separators. In mineral processing, partition curve analysis is routinely applied to hydrocyclones, screens, density separators and other beneficiation technologies that are based on intensive physical properties. Graphically, the partition curve depicts the recovery of particles as a function of the physical property on which the separation is based, such as particle density, size or magnetic susceptibility. Given the probabilistic nature of many real separators, the partition curve often exhibits a characteristic S shape (Fig. 1), similar to a cumulative normal distribution. Other geometric features of the curve are also depicted in Fig. 1, including the high and low closeout, or bypass, values; the midpoint slope; and the separation cut point, defined as the property value with 50 percent recovery.Partition curve analysis was originally proposed to evaluate coal washability (Tromp, 1937). Given the limited computational resources at the time, the analytical methods relied heavily on graphical construction and interpretation of the curve. Owing to the simplicity of calculation and interpretation, many of these graphical approaches are still widely used for performance analysis today. The most common calculations are based on the slope of the partition curve at the midpoint. Increased slopes correspond to enhanced separation performance, as a perfect separation exhibits a stepwise transition from 0 to 1 at the desired cut point, that is, an infinitely large slope. One common formulation of this slope, the Ecart Probable, Ep, is derived by evaluating the slope between the 25 and 75 percent recovery points:"

Jan 1, 2016

By John A. Brooks

The description of a phosphate flotation operation is repeat information for many people, except for variations in flow sheets. This paper is written to show the variations in flows, and to give enough. of the overall flows to allow anyone not familiar with the operation to be able to formulate a fair idea of the operations.

Jan 1, 1962

By Alten F. Grandt

Surface mining consists of the removal of the geologic strata overlying the coal seam usually with large electric shovels, draglines or bucket wheels. The method produces more or less parallel ridges or peaks of cast overburden, usually called "spoil banks". The mined lands vary widely in their inherent characteristics to produce a vegetative cover and thus can be put to a wide variety of uses. Use is the key to economic and social benefits. Physical and Chemical Characteristics of Soil Material of Surface Mined Lands after surface mining operations, the soil material is a heterogeneous mass whose physical and chemical properties are dominated by the character of the geologic strata overlying the coal. These strata are highly variable in thickness and character. They may include the surface soil, loess, glacial till, sands, shales, slates, limestone and sandstone rock. The method of mining with the several types of mining equipment will also affect the resultant mined area.

Jan 1, 1968

By J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is n practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota (a) must be covered with about 70 cm of soil material to achieve maximum production; (b) topsoil must be segregated and spread separately from subsoil; (c) potential production depends on the quality of the soil material returned; and (d) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation. Almost half the nation's cool reserves are in the Northern Great Plains underlying several million hectares of agricultural land. Social pressures to return mined land to agriculture or other productive uses have resulted in recent enactment of state and federal legislation, which is intended to restore productivity to disturbed areas. All such legislation relating to the Northern Great Plains has stipulated that useable soil material be saved and returned to mined land after spoils are smoothed. This requirement immediately raises questions as to how much soil material is needed, what criteria are important in defining useable soil material, how is the soil material to be handled in the earth-moving operations involved, and how can replaced soil material be maintained and revegetation. Scientists at the USDA Northern Great Plains Research Center at Mandan, North Dakota have conducted research on the reclamation of disturbed lands since 1970. Initially this research was designed to identify and characterize those physical and chemical properties of spoils that are most restrictive to plant growth (1). Basically, they found that any properties of spoils that reduced the efficiency of storage and utilization of the limited precipitation received adversely affected plant growth. Thus, in the Northern Plains, revegetation of mined land was found to depend upon the management of factors affecting the availability of water to plants - the same as on unmined land. After the major problems in revegetation were identified, technologies were developed to circumvent the effects of the growth-limiting factors (2). Basically two approaches were identified by which plant growth-restricting properties of spoils could be corrected: (a) various amendments (gypsum, sulfur, Fertilizers, mulches, calcium chloride, etc.) could be applied to spoils to improve their ability to conserve precipitation and provide water for plant growth; or (b) undesirable spoils could be covered with suitable soil materials to reduce or alleviate adverse effects. The latter approach appeared to be more feasible in most instances And is the approach specified in current legislation. The remainder of this paper discusses research on the use of roil materials returned to spoils and summarizes the information obtained.

Jan 1, 1978

By A. J. S. Spearing, A. Mueller

The support of intersections in coal mines remains an important safety issue, mainly because the large diagonal span compromises the stability of the roof. This structural weakness is further exacerbated if the intersection is developed incorrectly, the pillar corners fail or the crosscuts are angled (not perpendicular). This report details the current support systems used and investigates unplanned falls of ground in intersections in coal mines throughout the United States. A possible failure mechanism is proposed and some suggestions are made to improve the effectiveness of the support in these vital areas.

Jan 1, 2009

By Emre Karakaya, Niyazi Bilim

Boreholes are used for many purposes in mining operations, petroleum engineering, and construction works. Numerous factors affect the performance of drilling equipment. Researchers continue to work on the variable drilling parameters that can be adjusted in order to reach more efficient drilling operations. Penetration rate is an essential indicator in drillability analysis and estimating. This parameter is of great importance in mining projects. There are almost no models that can estimate the penetration rate for core drilling operations. Under the abovementioned circumstances, this paper focuses on developing models that allow estimating the penetration rate based on rock material properties. During the conduct of this study, drilling experiments under 11 different pressure forces were performed on 8 different rock units, and the equations which estimated the penetration rate depending on the physico-mechanical properties of the rock samples were derived. Experiments were carried out under different pressure forces to investigate the effect of the pressure force on the derived estimation models. The obtained results allowed deriving equations that ensured estimating the penetration rate based on the physico-mechanical properties of the rocks and the applied pressure force. Using these equations, the penetration rate in core drilling operations can be estimated.

Sep 30, 2020

By P. J. G. du Toi

Anaconda's experience with percussion longhole drilling in Butte, Montana, has consisted of six phases: 1. Drilling horizontal blast holes in stopes with push feeds. 2. Ring and parallel blast hole drilling in longhole stopes with bar mounted as well as skid jumbo mounted longhole drifters. 3. Ring and parallel drilling in raise climber shrinkage stoping using special raise climber drilling decks designed and built in Butte, Montana. 4. Parallel longhole drilling in horizontal cut and fill stopes with monorail jumbo. 5. Drilling water drain holes between mine levels. 6. Drilling leach holes through caved zones into old stope workings for leaching purposes. 7. Sample hole drilling.

Jan 1, 1970

By Arthur E. Belton

Ever since the industrial Revolution both major and small companies have put much emphasis on the use of incentives to compensate top management for extra effort and extra skill. For many years industries have also provided hourly rate employees with incentive plans. More recently incentive plans have been extended to include the "front line" supervisors. Many companies have what are called Christmas bonus or profit-sharing plans. The incentives for foremen in mining, which we shall discuss, differ from such bonus plans in that the incentives are paid on a definite measured performance for each individual, and thus directly reflect his effort and skill. What is the objective for paying incentives? The objective for any part of an industrial Engineering Program is to increase productivity and reduce unit cost. The unit cost must include the entire cost of the program. From what base do we start an incentive plan? One should think of art incentive program as the top rung of the Industrial Engineering ladder. Therefore, a company must take several steps before reaching this top rung. The following steps are necessary:

Jan 1, 1960

By Edward S. Plotkin, Gary A. Almeraris, Thomas F. Peyton

The lining of the tunnel and shafts for a new section of New York City's- water system required extensive components to produce, deliver and place a continuous tunnel linning. The project placed approximately 153,000 CM (200,000 cy) of concrete for 5,340 M (17,520) of drill and blast 7.3 M (24 ft.) ID tunnel, located at depths of 152 M (500 ft.) to 213 M (700 ft.) . This section of tunnel will be connected to the surface water distribution system via four shafts of varying diameters ranging from 5.8 M (19 ft.) ID to 1.5 M (5 ft.) ID . All work was done beneath the streets of Manhattan under the rigid constraints of the City of New York and the Bureau of Water Supply regulations.

Jan 1, 1987

By Chee Theng

"In 2013, Coeur Mining had more than $55 million in general and administrative (G&A) costs and less than $100 million in cash flow. This year, its G&A costs stand at $30 million, down by more than 40 percent, its all-in sustaining costs have shrunk by more than 30 percent, and its cash flow is above $200 million. To realize this, the company aggressively reduced both its corporate overhead cost and operating cost and repaid more than $300 million in debt.The more robust balance sheet meant the precious-metals producer was well positioned to reap the rewards of an upsurge in commodity prices in the early part of 2016. Its stock price soared from $1.75 in January to $15.98 in August. Although the stock price has since dropped to around $9 due to a stronger dollar and a more hawkish Federal Reserve that recently raised U.S. interest rates, shifting the opportunity-cost argument away from buying gold and silver, Coeur remains attractive to analysts in light of its prudent spending and improved fundamentals.Focus on balanced portfolioCoeur is the largest primary silver producer and one of the largest gold-producing companies in the United States and one of the largest silver companies in the world. Incorporated in 1928, the U.S.-listed company has a total of five operations: three in the United States, one in Mexico and one in Bolivia. About two-thirds of its revenue comes from the United States.The company is conscientious about having a balanced portfolio, so no single mine accounts for more than about 30 percent of its business. Being in three different jurisdictions provides further diversification, and its revenue split of about 60 percent from gold and 40 percent from silver gives it some metals mix. This year, it expects to produce about 466 t (15 million oz) of silver and 10.3 t (330,000 oz) of gold."

Feb 1, 2017

By Inoka E. Perera, Robert Hildebrandt, Gerrit V. R. Goodman, Krzysztof Cybulski, Zdzisław Dyduch, Michael J. Sapko, Marcia L. Harris

To prevent coal dust explosion propagations, rock dust needs to be lifted and suspended in the air with the coal dust during an explosion. The addition of anti-caking agents prevents caking of rock dust in the presence of water. Mining and rock dusting processes can frequently create alternating layers of rock dust and float coal dust on mine surfaces. For this test series, a thin layer of coal dust was distributed on top of a layer of either treated or non-treated rock dust in the Experimental Mine Barbara, Poland. The experimental results compare the effectiveness of treated and non-treated rock dusts to attenuate a propagating coal dust explosion initiated with either strong or weak methane explosions. Experimental results indicate that the treated rock dust performs better than non-treated rock dust in arresting a propagating explosion, especially in the presence of moisture.

Jan 20, 2020

By Ch. R. V. S. Nagesh, Ramesh Naidu Mandapati, Venkata Swamy Nalajala, Tondepu Subbaiah, Naga Jyothi Kothamasu

Leaching studies of magnesite obtained from Tamilnadu Magnesite Limited, Salem, have been carried out using hydrochloric acid leaching and percentage of magnesium chloride recovered was estimated. The variables considered in this study were the following: duration of leaching, volume percentage of hydrochloric acid, temperature, and pulp density. Percentage recovery of magnesium chloride increased with duration of the leaching, volume % of concentrated hydrochloric acid, and temperature. Percentage recovery of magnesium chloride decreased with increase of pulp density. The optimum conditions found to be pulp density (10%), hydrochloric acid concentration (30%), duration of leaching (2 h), and temperature (348.15 K). Iron was removed by treating the leach liquor with hydrogen peroxide and by raising the pH to 3.5–4. The purified leach liquor was subjected to spray drying for producing high pure magnesium chloride.

Jun 7, 2022

By W. M. Husslage

The permeability in the blast furnace shaft is adversely affected by low temperature reduction degradation of sinters. The fundamental cause is an expansion of the iron oxide phase resulting from reduction of hematite to magnetite. The present study showed that expansion behavior during the hematite / magnetite reduction step and the resulting microstructure are strongly influenced by the reduction temperature (viz. partial oxygen pressure), the reducing agent and the nature of the hematite. The reduction rate is of minor importance. A reduction mechanism is proposed, explaining the dilation behavior and the magnetite microstructure. The results can provide better insight into reduction degradation behavior.

Jan 1, 1998

Critical safety tools to locate miners underground are featured by several exhibitors at MINExpo. Communication was the buzzword for health and safety products at the 2008 MINExpo, and it is still important in 2012. Products unveiled following the Miner Act in 2006 have been upgraded and improved. Saving lives and reducing injuries through better leadership, planning and practice is the goal of every mine professional.

Jan 1, 2012

By Henry Rumfelt

Strip mining in the domestic coal industry is contributing a greater proportion of overall production than at any time in the past. U. S. Bureau of Mimes statistics show that the percentage of total production mined in 1958 by stripping methods in- creased to more than 30 pct, up from 22 pct in 1951. The tendency to favor strip and open pit mining exists in other mining activities, but such trends are not as clearly outlined as in the coal industry. Significantly, the depth of overburden in coal properties considered suitable for stripping is also increasing. A depth of 50 to 60 ft of overburden was once considered to be about the maximum amount that could be handled economically, Today, a depth of 80 to 100 ft is frequently taken into consideration for simple overcasting operations (i.e., excavating over- burden and dumping it in the spoil position where it remains indefinitely). Significantly, the depth of overburden in coal properties considered suitable for stripping is also increasing. A depth of 50 to 60 ft of overburden was once considered to be about the maximum amount that could be handled economically, Today, a depth of 80 to 100 ft is frequently taken into consideration for simple overcasting operations (i.e., excavating overburden and dumping it in the spoil position where it remains indefinitely).

Jan 1, 1960

By David A. Fawcett

An auxiliary cross-pit mining system, working in tandem with the prime excavator, is evaluated technically, operationally and economically for application in the selective removal and replacement of soils and unconsolidated ovezburden. Previous studies on cross-pit technology and applications of this technology are briefly reviewed. Stratigraphy plus pit, operating and economic parameters are assumed and applied in the evaluation and comparison of a base case dragline system with two alternatives - a dragline/scraper-dozer combination and a drag- line/cross-pit system combination. The economics of the proposed cross-pit system favour it as a viable alternative to conventional systems.

Jan 1, 1981