Search Documents

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"Duluth & Iron Range Railroad. The Duluth & Iron Range Railroad was built from Two Harbors to the Vermilion range at Tower, a distance of 67.6 miles, in 1884, and extended to Ely, twenty-one miles east of Tower, in 1888. It was built into Duluth in 1886, and branches were extended from its main line to the Mesabi mines in 1892 and 1893. The original grades on this road are very steep, going north, and in the thirteen miles from Two Harbors to Highland there is a rise of 1,150 feet. A new line between these points has been built with an increase of three miles in distance and with maximum grades of 1 per cent. Duluth, Missabe & Northern Railway. The Duluth, Mis¬sabe & Northern Railway was constructed from Stony Brook to Mountain Iron, a distance of 48.62 miles, in 1892. The Biwabik branch from Iron Junction to Biwabik, a distance of 15.54 miles, was constructed in 1892. The Superior branch from Wolf to Hibbing, a distance of 16.06 miles, was co11structed in 1893. The Alborn branch from Coleraine Junction to Coleraine, a distance of 53 miles, was constructed in 1906. The total main line mileage is 242 miles, of which 82 miles from Duluth to Hibbing is double tracked"

Jan 1, 1920

By Mustafa Fener, Masoud Rostami, Sair Kahraman, Behnaz Dibavar

The paper introduces a new rock mass cuttability classification (RMCC) system for roadheaders used in coal mines. It includes performance prediction models for both axial and transverse roadheaders, based on six parameters: uniaxial compressive strength, Cerchar abrasivity index, volumetric joint count, strike and dip of joints, joint aperture, and groundwater condition. The study validates the RMCC system through field and laboratory measurements, showing high correlation coefficients between net cutting rates and RMCC indices.

Nov 1, 2023

By MARK J. VANARELLI

Estimating ground-water inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies, including the Chattahoochee and Nancy Creek tunnels, for estimating steady-state ground-water inflows into deep rock tunnels. Statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations, and a semiempirical procedure was used to estimate ground-water inflows. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels that exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semiempirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Modeling using Monte Carlo simulations was observed to be an effective tool for removing data distribution irregularities and incorporating high-end permeability data to derive reasonable ground-water inflow estimates.

By Xiaodong Yu, Jinxia Zhang, Fusheng Niu, Hongmei Zhang

The three-dimensional (3D) fractal dimension is an important parameter to analyze the 3D structure and flocculation effect of the hematite flocs. In this work, the 3D fractal dimension of hematite flocs was predicted by establishing the particle swarm optimization (PSO) algorithm optimized with the back propagation (BP) neural network (PSO-BP). The proposed model considers four factors, namely, the flocculant quantity, flocculation time, stirring speed, and temperature, as the input parameters. We normalize the input data during the preprocessing stage. The BP neural network was optimized by using the PSO algorithm for realizing the 3D fractal dimension. The prediction accuracy and effectiveness of the model were evaluated. The experimental results showed that the predictions performed by the proposed PSO-BP neural network were better than that of BP neural network. In addition, the root mean square error (RMSE), mean squared relative error (MSRE), mean absolute error (MAE), and mean absolute relative error (MARE) of the proposed model are lower, compared with the errors of the BP network. Similarly, the measurement coefficient R2 of the proposed model is higher, compared with the BP network. The maximum absolute error of the model is 0.0772, the maximum relative error is 0.02405, and the regression coefficient r is 0.98592. These results showed that the proposed model has a good performance and high prediction accuracy. When verifying the practicability and the effectiveness of the proposed PSO-BP model, the prediction results of 10 groups of hematite flocculation experimental data under different conditions showed that the prediction value of the proposed PSO-BP model was closer to the ground truth as compared to the BP model. Therefore, the proposed model is suitable for predicting the 3D fractal dimension of hematite flocculation.

Oct 3, 2022

By M. Boucraut

The authors investigate the influence of the basicity index CaO / Si02 on the sintering properties of hematite ore mixtures. The experimentation was performed with three different mixtures of ores from Tazadit, Nimba, Mano-River, Itabira, Marcona, Goa, Mapawa and Cassinga. Increasing the basicity index CaO / Si02 between 0.1 and 3, chiefly through limestone admixture makes possible to reduce the thermal consumption of sintering and to improve the physical and chemical properties of the sinter. In the case of a plant using hematite ores, it seems interesting to produce an hyperbasic sinter and to complete the blast furnace burden with calibrated ore or acid pellets.

Jan 1, 1968

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

8.1 INTRODUCTION Under room and pillar mining if the extraction ratio is low, (i.e., < 50%) a pillar can support the overburden without collapse and there will be no surface subsidence whatsoever. In other words, if the pillar sizes are properly determined to support the overburden weight, the roof strata cannot cave and there will be no surface subsidence, provided the entry width is small and properly reinforced so that a continuous roof fall leading to piping or the total collapse of the roof does not occur. Under the prevailing mining conditions in the US if only development mining is em¬ployed in room and pillar mining (i.e., no pillar extraction), the extraction ratio is usually less than 50% and generally no surface subsidence will occur. If pillar mining is employed, surface subsidence may occur, depending on the extraction ratio and the size of the remnant pillars (or stumps) left in the gob. The higher the extraction ratio, the smaller the stump pillars left behind in the gob. As the size of the stump pillars becomes smaller, the possibility of their support¬ing the roof without collapse is smaller. If all stumps are crushed completely, the roof will collapse and surface subsidence will occur. Again, whether surface subsidence occurs, it depends on whether the remaining stumps can support the overburden or not. Therefore, since the weight of the overburden which the stump pillars have to support is proportional to the mining depth, a fixed¬size stump pillar can support the overburden at a shallow depth, but will collapse under greater depths. In this context extraction ratio is not the only parameter for determining whether surface subsidence will occur. Furthermore, during pillar mining a pillar can be cut away in many ways to finally reach the same extraction ratio. Therefore, the safest way to determine whether or not sur¬face subsidence will occur in room and pillar mining is to compare the strength of all stump pillars in the panel of interest with the weight of the overburden that the pillars have to support. If they are too small to support the overburden, surface subsidence will occur. Under normal mining practices the characteristics of surface subsidence profiles vary with methods of mining. In the US there are two types of coal mining methods, i.e., longwall and room and pillar mining. Longwall mining is indisputably a total extraction method, but different percentages of coal recovery are achieved in room and pillar mining. Recovery is much higher for sections with pillar extraction than those without pillar extraction. For those without pillar extraction, coal recovery increases with increasing entry width or decreasing pillar size. For those with pillar extrac¬tion, the total coal recovery depends on the amount of coal ex¬tracted from each pillar which is in turn dependent on the roof conditions and methods of pillar extraction. Bauer and Hunt (1981) analyzed the characteristics of the subsidence profiles due to the three types of mining methods in Illinois. Fig. 8.1 shows the range of locations associated with the following profile features: profile edge, maximum tensile curvature, maximum slope, maxi¬mum compressive curvature, and maximum subsidence. The scat¬ter of the data increases with decreasing percentages of extraction. The profile is much sharper for longwall mining and becomes milder as percentage of extraction decreases; for longwall mining the profile edge is always beyond the opening, while in room and pillar mining it may fall within. The location of maximum tensile strain moves outward, while that of the maximum compressive strain moves inward as the percentage of extraction decreases and the maximum subsidence decreases with decreasing extraction ra¬tio. The general concepts discussed in this chapter may not apply to the entry development sections between two longwall panels where roof caving in both panels are very severe and overlap each other. Consequently, it must be treated differently. 8.2 CASE STUDIES Kohli et al. (1982) described several case studies on surface subsidence due to room and pillar mining with pillar extraction. In one case, the seam was 6 ft thick and ranged from 650 to 800 ft deep. The panel was 720 ft wide (Fig. 8.2) and was developed with seven entries. Each entry was 18 ft wide and the pillars were driven at 88 ft center-to-center between entries and crosscuts. Dur¬ing retreating, two additional pillars (pillars J and K) were devel¬oped, two blocks ahead of the pillar line, to take the barrier pillar, 160 ft wide, between panel No. I and No. 2. Pillar extraction began by taking a central slice across the whole panel, beginning from pillar 0 through J. After that, each pillar was sliced by 6 wing-slices, 3 on each side, leaving 4 stumps, 2 on each side. One of each pair was triangular shaped approximately 6 ft wide by 26 ft long. The other was trapezoidal, 26 ft long by 16 ft and 10 ft wide at the upper and lower bases, respectively. This resulted in a total extraction ratio of 85% within the panel. Obviously the stump pillars were not large enough to support the overburden and col¬lapsed completely. The final subsidence profiles were rather smooth, just like those under total extraction (Fig. 8.3). The max¬imum subsidence on Lines A and B was about 3 ft for an average mining height of 6 ft, but the locations of the maximum subsidence were skewed toward panel No. 1. Along Line D, the central por¬tion was flat-bottomed, but the maximum subsidence was only 2 ft, mainly because Line D was only two blocks from the right-side edge. Notice in every profile there was heaving of as much as 0.3 ft, beyond the edges above the solid coal. In another case (Fig. 8.4), the seam was 6 ft thick under 650 to 850 ft cover. Three panels, 710, 400, and 350 ft wide, respec¬tively, were extracted side by side. The entries were 18 ft wide and the pillars at 88 ft center-to-center between entries and crosscuts. Pillar extraction was practiced the same way as described previ¬ously. According to the mine maps, there was no barrier pillar left between the adjacent panels. Thus after extraction the three panels formed a common gob of more than 1460 ft wide. This was re¬flected in the development of the subsidence profile along the county road. After Panel No. I was mined, the maximum subsi¬dence of 1.2 ft occurred at Monument No. 1. This was increased to 1.6 ft after the extraction of Panel No. 2 and went to a further 1.8 ft after the extraction of Panel No. 3. The final maximum subsidence of 4.3 ft occurred at Monuments No. 6 through No. 8, while the remaining portion of the county road showed rebound. However it must be noted that the subsidence profiles were rather bumpy and fluctuated, perhaps an indication of the irregular stump pillars that were left and crushed at various time after mining. Moebs (1982) surveyed the subsidence profiles of four room

Jan 1, 1992

By Meng Li, Hao Nie, Weitian Ding, Mamdouh Omran, Ying Li, Yao Ge, Yaowei Yu, Abourehab Hammam, Lei Zan

This study examines the isothermal and non-isothermal reduction behaviors of iron ore compacts in a pure hydrogen atmosphere and compares the results obtained during the reduction process by CO. The different phases accompanying the reduction reactions were identified using X-ray diffraction (XRD) and its morphology was microscopically examined. In isothermal experiments, temperature plays a significant role in the reduction process. At any given temperature, the reduction rate during the initial stages is higher than that during the final stages. The reduction rate in H2 atmosphere was faster than in CO gas. The comparison of activation energy values suggested that reduction with H2 is more efficient thanwith CO. At the same temperature, the time required to achieve a certain degree of reduction was lower when using H2 gas than CO atmosphere. In non-isothermal tests, the heating rate has a significant effect on the reduction rate and reduction extent. At the same heating rate, the degree of reduction was higher in H2 atmosphere than in CO gas. Based on experimental data, the parameters of reaction kinetics were deduced by application of model-free and model-fitting methods. The reduction in H2 atmosphere was controlled by nucleation model (Avrami-Erofeev model), while the CO reduction reaction was controlled by gas diffusion.

Sep 29, 2020

By Evgueni Jak

Pyrometallurgy is an important sector of modern industrial society actively participating in solving current environmental, economic, materials scarcity and other challenges. Recent advances in analytical methods, experimental techniques, thermodynamic, phase equilibria and process modelling tools provide new opportunities to increase the productivity of pyrometallurgical reactors, the treatment of complex feeds and metal recoveries. Fundamental theoretical models can now be used to make a significant next step towards the development and implementation of computerised models describing real industrial processes—Virtual Reactors, and computer-aided smart-decision-making systems that may be called Pyro-GPS by analogy to GPS; these developments can facilitate knowledge-based improvement and optimization strategies. The implementation of these improvements require ongoing collaboration between researchers, industry and government

By Jianbo Hu, Gang Han, Tao Zheng, Junfeng Jiang, Rui Su, Qihua Zhao

The rock quality designation (RQD) is a commonly used index for the classification and evaluation of rock mass quality and is widely adopted in mining and geological engineering. The traditional method of obtaining RQD still requires manual measurement of core length and calculation of RQD, which is inefficient. To address this problem, we propose a framework for drilling core image segmentation and RQD estimation from digital images of cores in core boxes based on the deep learning algorithm. The proposed framework is generated by combining the Mask Region-Based Convolutional Neural Networks (Mask R-CNN) instance segmentation algorithm, the U-Shaped Convolutional Neural Networks (U-Net) semantic segmentation algorithm, and the image processing functions of the Open Source Computer Vision Library (OpenCV). To demonstrate the accuracy of the proposed method, seven boreholes in the Xiushuihe vanadium-titanium magnetite mine, located in the Sichuan Province, China, were used as the case study. According to the comparison of the manual measurements and calculations of the cores taken from seven boreholes used to conduct this study, the framework can record the length of the drill cores and calculate RQD within an average error rate of 3.42%, while it saves about 85% of the working time. The results illustrate that the proposed framework enhances the efficiency of RQD calculation while satisfying the engineering requirements.

Jul 31, 2023

By G. K. Hoffman

Humate, defined as weathered coal or mud-stone rich in humic acid (HA) and fulvic acid (FA) have been mined, primarily as soil amendments or drilling mud additives, in New Mexico for 15-20 years. The New Mexico humate resource is estimated to be 11 Gt, including weathered coal and organic mudstone. The HA and FA content determines the end-use, therefore a simple and consistent method of measuring organic-acid content was developed. The New Mexico Bureau of Mines and Mineral Resources method is based on repeated alkali leaching and acid precipitation. Precipitates of humate are ashed, with mass balance of solids maintained, to correct for material added during alkali-acid treatment. Analyses of upper coal member, Cleary Coal Member (Menefee Formation) and Fruitland Formation samples from the southeast San Juan Basin show ashing to be important in accurate analysis of FA content. Ash in the total FA fraction averages 70% compared to 2% in HA. The FA in weathered coal and organic mudstone are similar, although HA is significantly higher in the former. As weathering progresses, the FA content of weathered coal increases faster than in organic mudstone because of the greater total organic material in coal.

Jan 1, 1994

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector, which has an important place in terms of raw material and energy supply, is referred as a sector with one of the highest fatal accidents in comparison with other sectors. In this century, where occupational health and safety awareness has increased, it is important to review the past accident statistics and to determine the current deficiencies by using the information in the inventory. In this study, the Malmquist total factor productivity index (MPI) has been utilized to investigate the changes in the work accidents occurring in the Western Lignite Corporation (Turkey), where underground and surface production methods are applied, and to determine the measures to be taken. According to the results obtained, both the decrease in production amount and the increase in the number of accidents caused inefficiencies during the period in concern due to the expected 10-year economic life of the mechanized system operating in the underground production panel that came to an end in 2007 and the flooding took place in early 2017. Compared with the underground operations, it has been determined that production can be carried out at the appropriate scale despite the heavy working conditions encountered due to the changing climatic conditions and the progress of production in the surface operations.

By J. Mark Richardson

The use of an integrated software package to simulate and optimize the performance of mineral processing circuits is illustrated by three examples. Each represents application of the software and associated techniques to optimization of an existing plant. In the first example, a South-western U. S. copper company employs the method to simulate and improve performance in crushing, screening and SAG milling. A second copper producer evaluates equipment changes and flowsheet alternatives in a closed-circuit ball mill-cyclone operation. A Southeastern U. S. aluminum refinery optimizes performance of a dry milling and classification circuit for production of carbon particles used in anode casting. Graphical and tabular data describe the circuits simulated and the results achieved in each example.

Jan 1, 1990

By SHANTAE LEE, ELAHEH TALEBI, Frank A. Drews, W. Pratt Rogers

Fatigue in mining operations is a serious issue and a significant contributor to incidents and accidents. While mine operators are using or introducing new technology to monitor operator fatigue, there is little work that focuses on the subjective experience of fatigue and the use of fatigue monitoring technology. To investigate this issue, eight focus groups with a total of 44 operators of heavy haulage equipment working for two mining companies in the Mountain West of the USA participated in 1-h focus groups. The topic of the focus groups was the experience of operator fatigue and issues surrounding fatigue at the workplace. The results of the content analyses suggest that operators are well aware of the signs of fatigue, and that they understand the severity of these signs as well. In addition, they are aware of the effect of fatigue on driving performance and are using a wide range of methods to manage fatigue. Finally, based on participants’ assessment, current fatigue monitoring systems lack face validity and reliability and are perceived as not being effective. The results of this study emphasize the importance of a socio-technical systems perspective in the context of miner health and safety management. Only such a comprehensive perspective can result in improvements that are sustainable.

Jun 17, 2020

By L. J. Vincze

The program of study of pellet binder materials was begun by the ORF in 1963 to examine various Canadian materials as substitutes for bentonite which is imported in large tonnages (199,270 tons in 1969) from the U.S.A. for Canadian pellet plant operations. Most of the raw bentonite used in Canada originates in Wyoming, North Dakota and more recently Greece, resulting in relatively high transportation costs to pellet producers. Some Canadian bentonites available in Western Canada (Alberta) can be beneficiated for uses as pellet binders but could not compete in cost with U.S. sources due to the cost of beneficiation and the higher rail transport charges to Eastern Canada. It is difficult to find a substitute for bentonite, and many materials have been investigated by research groups but, so far, no economic substitute is in use. However, some success is apparent in studies of low cost materials such as clays, sea weed, peat moss and low grade coal, The work done by the ORF over several years has covered systematic test¬ing of Ontario clays, lignite, some types of tree bark, waste sulphite liquors of various kinds, and peat moss as binders for iron ore pellets. The major effort has been concentrated on peat moss and has included a study of the influence of different additives. Since analysis of peat moss for humic acid is difficult and time consuming, a certain amount of time was devoted to development of improved methods, the most useful of which was a spectrophotometric method based on extraction of peat by sodium pyrophosphate for determination of humic substances. In the present paper, only the most recent work concerning the use of peat moss with suitable additives is discussed in detail, since it is the most conclusive and best documented portion of the program.

Jan 1, 1971

By Amir Karami, Scott Munro

This paper focuses on remediation of a 3.6 km long water conveyance tunnel that suffered two large falls of ground (FoGs), one of which subsequently progressed to the ground surface, resulting in full collapse of the tunnel. The tunnel is part of a network of water conveyance tunnels and open channels that direct water into two turbines located in an underground powerhouse, originally constructed in the 1970s. At the time of construction, the tunnel was partially supported with shotcrete or rock bolts, with no further ground support added since construction. Two sonar surveys in 019 and 01 identied two adacent large FoGs in the tunnel, approimately 1.2 km from the tunnel outlet. Historical geological and geotechnical information indicated that the FoGs occurred within a 60 m wide fault zone. Remediation plans were developed, which included stabilization of the outlet channel, the portal, the tunnel leading up to the FoG areas (1.2 km length) and the FoG areas. Several remediation options were considered to restore the tunnel, including construction of a diversion tunnel to bypass the FoGs or remediation of the FoG areas with steel ribs and backlling the void above the FoGs to surface.

Jun 23, 2024

By R. Mensah-Biney

The aqueous biphase separation process (ABS) has been used to separate ultrafine industrial minerals. The partition behavior ofTiO2, Al2O3, Fe2O3 and kaolin was not pH dependent. The partition behavior of SiO2 was, however, pH dependent. The partition coefficient of kaolin in PEG 3400/ Na2CO3 biphase system was 150 and that of the silica in the same system was 0.02, resulting in a separation factor of 8500 between kaolin and silica. The aqueous biphase separation system was used to separate free silica from kaolin in a raw clay sample from Mexico. The partition behavior of mica, feldspar and clay from North Carolina was also evaluated.

Jan 1, 1999

By Richard E. Ray, George N. Aul, Fred Garcia, William P. Diamond

Increasing longwall panel dimensions, particularly face width in gassy coalbeds, may result in unexpected increases in methane emissions. To investigate this problem, continuous longwall face emission monitoring studies were conducted at two adjacent mines operating in the Pocahontas No. 3 Coalbed, where longwall faces were to be extended from 229 to 305 m (750 to 1,000 ft). It was predicted by regression analysis of methane emissions data from 229 m (750 ft) wide longwall faces that extending faces to 305 m (1,000 ft) would increase methane emission rates by only 7 percent (0.6 m3/min (20 cfm)), to 8.6 m3/min (304 cfm) at the VP-1 Mine. In contrast, it was predicted that extending faces at the VP-3 Mine could increase methane emissions by as much as 13 percent (1.8 m3/min (65 cfm)) to 16.1 m3/min (567 cfm). The geologic and mine design factors in¬fluencing the variation in face emissions between the two mines will be discussed.

Jan 1, 1997

By K. Awuah-Offei, A. U. Rehman

"Information diffusion potential of a social media user affects how quickly information about a mineral project can diffuse through that user. If management can use social media and network analysis, in community engagement program, to understand how fast and how far information will diffuse to communities and followers of particular social media users, it can selectively focus on the most influential users. This paper proposes a method to examine the information diffusion potential of social media accounts. The work uses Gephi, an open source software, to extract and analyze data from different Twitter handles to predict their information diffusion potential. The work uses case studies of real Twitter users (e.g. mining news organizations and bloggers) associated with mining to illustrate the approach. The case study results show that there are significant disparities in information diffusion potential that will demand selective attention. This research will help mines develop effective social media engagement strategies. INTRODUCTION The mineral industry provides raw material for industrial activity to support our society (Martens and Rattmann, 2001). Mines have changed conventional mining practices to sustainable ones because of the negative impacts of mining and increased public awareness (Wang et al 2016). The concept of sustainable mining is getting mature as stakeholders (e.g., governments, investors and host communities) are getting involved in mining projects (World Economic Forum, 2014). The failure of mining companies to address the demands of these stakeholders might result in failure to acquire social license to operate (Thomson and Boutilier, 2011). The social license to operate (SLO), if granted, is mutually beneficial to all stakeholders. Mines prefer being granted SLO and keeping it to avoid any kind of social unrest due to their operation (Prno, 2013; Moffat and Zhang, 2014). Mining communities can grant different levels of SLO; ranging from withholding SLO to psychologically identifying with the project (Joyce and Thomson, 2000; Thomsan and Boutilier, 2011). Most of the previous work to understand community perceptions and SLO in mining is generally qualitative (ICMM, 2012a; Thomson and Boutilier, 2011; Prno, 2013; Moffat and Zhang, 2014; IFC, 2014). In particular, there is limited work on how community perceptions change over time due to information diffusion (Boateng and Awuah-Offei, 2017). However, SLO changes with respect to time (Yates and Horvath, 2013), which can result in risks that are not easy to predict. Mine managers and engineers have a desire to understand these changes so as to mitigate these risks (Que and Awuah-Offei, 2014; Que et al., 2015)."

Jan 1, 2018

By James N. White

Completion of the Hall Street Coal Transfer Terminal in St. Louis marks the beginning of a major shift in the movement of coal to the power generating stations of the Midwest and South Central regions of the United States. The location of the terminal is significant. The 10 million ton- per-year facility is the first high capacity rail-to-barge transfer terminal to be built on the western shore of the Mississippi. This terminal and others to follow will link the massive coal fields of the West with the high coal consuming markets adjacent to the 25,000-mile Inland Waterway System.

Jan 1, 1979

By S. Hamm

Elevated total dissolved solids (TDS) content in waters downstream from surface coal mines in Central Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and ICP-MS was used to determine how leaching conditions affected release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that, for certain spoil materials, SC in leach column effluent was effectively reduced when spoil was leached first with acidic rainwater followed by ambient rainwater (vs. ambient rainwater leaching alone). This suggests that accelerated leaching might aid in long-term stabilization of some materials.

Feb 23, 2014