Search Documents

Beatrix Gold Mine, a deep-level gold mine in the Free State province of South Africa, has the highest methane emission rate of any gold mine in the country. Methane is emitted from underground sources intersected during mining operations and is liberated into the general mine atmosphere. The total methane emission rate for the mine is of the order of 16001/s and the South section of the mine emits approximately 10001/s of methane gas. The mine has a history of gas accumulations which have led to a number of underground explosions. Following the last explosion in 2001 and the subsequent investigation, a number of recommendations were made. Two of these were to consider extracting the underground mine methane to render the mine atmosphere safe, and to declare hazardous locations that require special operating procedures. A number of such workplaces have now been declared at the South section of the mine. Methane gas is a potent, explosive greenhouse gas whose contribution to global warming and climate change is 21 times higher than that of carbon dioxide. To reduce its inherent danger and to mitigate its global warming impact, a carbon credit project under the Clean Development Mechanism (CDM) of the Kyoto Protocol has been developed and implemented, the aim being to capture and destroy the methane at Beatrix mine. The mine has constructed an extraction system to capture and extract 400 (Is of the methane. Percentage methane (per volume) of the gas intersected at source is 85%, with negligible concentrations of other hydrocarbons and water associated. The mine contracted the services of Group Five to design and construct the flare and ancillary equipment on surface, and Promethium Carbon was contracted to assist with the carbon¬-related aspects, approval framework, and administration of the project. A number of design and construction challenges had to be faced to extract and transport the gas effectively to the surface of the mine as the emitters are approximately 3 600 m away from the mine shaft at a depth of 860 m. Further considerations were the requirements for the type of column to be used to transport the methane gas, the pressure loss over the system, the safety systems needed to address the risk factors involved in the transport of the methane gas, and a suitable pumping system to extract the gas to the surface. The system operates under negative pressure provided by two blowers on surface delivering the emissions to a flare capable of burning off 450 8/s of methane gas. In this paper a number of benefits for the mine are discussed. These include, but are not limited to, the removal of approximately 55% of the total volume of methane gas from the general body of the air in the geographical areas of the mine where the methane gas is emitted into the atmosphere, and reducing the risk of methane-related incidents. A further benefit of this project is the mitigation of the global warming impact of the methane gas and the reduction of the mine's carbon footprint by approximately 25%. This project could also assist in alleviating the energy shortage being experienced in South Africa by means of the planned generation of 4 MW of electrical power, utilizing the methane gas, as a second phase of the project.

Jan 1, 2011

By J. Rogans

This paper discusses the comparative performances of the three activated carbon adsorption circuits at the West Wits operations of Anglogold. These circuits consist of two pump-cell circuits (at Two Plant, formerly Elandsrand and at Three plant) and a conventional counter-current adsorption circuit (at Mponeng plant). The implications of the improved performance of the pump-cell plants are discussed.

Jan 1, 2002

By D. D. Munro

Finsch Mine is a kimberlite diamond mine located at Lime Acres in the Northern Cape Province of South Africa. The mine was founded in 1961 and started surface mining in 1964. Underground production commenced in 1990 using a modified blast-hole open stoping method for the mining of Blocks 1, 2 and 3. Block 4 is currently being mined as a block cave. The process of identifying and optimizing a method to mine the Block 5 orebody started in 1991, and in 2006 incline caving was identified as being technically feasible. This paper aims to document the process employed in developing this method by the Block 5 prefeasibility team as well as discuss the technical challenges encountered during this process. The paper commences with a history of Finsch Mine and highlights the complex geology and threat of sidewall failure that prompted the decision to use block caving as the mining method for Block 4. A literature study of mines that implemented mining methods upon which the incline cave was conceptualized is then presented. These practices were then used to form the basis for the designs on which the initial geotechnical modelling was done and built upon through an iterative process of modelling and design changes. The ventilation of the mining area, initial productivity simulation results, and the applicability of automation and comminution processes in the incline cave are also presented. The paper concludes with an investigation into some of the challenges of the mining method, and shows that that incline caving is a technical option available for further investigation in determining the optimal mining method to be employed at Block 5, Finsch Diamond Mine. Keywords massive mining, incline caving, geotechnical modelling.

Jul 1, 2013

By C. J. H. Steenkamp

Theoretically, the main driver behind a mining operations? sourcing decision should differ from company to company, and within a company from project to project, but in reality it often relates to cost. Research confirms that there are a number of factors, including cost, to consider when choosing between in-house and outsourced mining. While the literature is rife with factors to consider, little information exists on how to apply these in practice and the relative importance of the different factors to be considered. A study was conducted to determine whether mining is truly a core competency for a mid-tier commodity specialist mining company. Furthermore, a decision-making framework for mining operations sourcing was developed, and the critical success factors that should be adhered to if outsourced mining is chosen were determined. The research showed that owner mining is not a core competency for the mining company investigated. A decision-making framework was developed using the order winner/order qualifier structure, which can be used to facilitate the mining sourcing decision. The most important tools at the disposal of a mine owner?s team to manage a contractor miner are the social and output control mechanisms, according to the critical success factors study.

Jan 1, 2014

By Y. van der Grijp

The applicability of a stochastic approach to the simulation of gold distribution to assess the uncertainty of the associated mineralization is examined. A practical workflow for similar problems is proposed. Two different techniques are explored in this research: a Direct Sampling multi-point simulation algorithm is used for generating realizations of lithologies hosting the gold mineralization, and sequential Gaussian simulation is applied to generate multiple realizations of gold distributions within the host lithologies. A range of parameters in the Direct Sampling algorithm is investigated to arrive at good reproducibility of the patterns found in the training image. These findings are aimed at assisting in the choice of appropriate parameters when undertaking the simulation step. The resulting realizations are analysed in order to assess the combined uncertainty associated with the lithology and gold mineralization.

Jan 1, 2015

By C. -T. Mutale, A. S. Tuling

Titanium can exist in three different oxidation states. Its oxides are numerous and in presence of iron and oxygen, iron-titanium oxide compounds can also form. Some of the oxides are non-stoichiometric, making the determination of the thermodynamic properties of titanium and its oxides in molten steel and in slag difficult. Therefore, for the assessment of titanium activity in molten steel using the electrochemical measurements of oxygen partial pressure, the identification of oxides in equilibrium with titanium is important. This paper reports on an investigation of solid titanium oxide inclusions, which have been identified by combining different methods of analysis on quenched samples. These samples were taken from a Fe-Ti-melt at 1600°C, quenched in cold water then mounted and polished for optical microscopy. The oxide inclusions were analysed using transmission electron microscopy (TEM) with energy dispersive spectroscopy (EDS). Both single crystal and polycrystalline diffraction patterns were used to identify the oxides by comparing the d spacings with those in the ICDD X-Ray Diffraction (XRD) database. XRD was used to analyse the oxide particles on the top of slow cooled samples. It was found in the TEM study that the similarity of the diffraction patterns of the various phases meant that unique identification was difficult to achieve in some of the diffraction patterns. However, TiO, Ti2O3, Ti3O5, Ti4O7were identified in quenched samples, while TiO2, FeO.TiO2and iron oxides were seen in slow cooled samples. It was also confirmed that the type of oxides is related to titanium content of the samples. Keywords: Titanium, Titanium Oxides, Iron, TEM, XRD, thermodynamic.

Jan 1, 2004

By M. Gous

Keywords: Pyrometallurgy, Namakwa Sands, ilmenite, DC arc furnace, titania slag, pig iron Namakwa Sands is a heavy minerals mining and beneficiation business in the Anglo Base Metals Division, and operates along the West Coast of South Africa. The business encompasses mining, mineral concentration, separation, and smelting operations. The smelting process comprises the carbonaceous reduction of ilmenite to produce titania slag with a TiO2 content of 86%, and iron with a carbon content of 2.5%. The Namakwa Sands smelter, situated near the Saldanha Bay harbour, commenced smelting operations in 1994, when a 25 MW DC arc furnace was commissioned. The smelting operations were expanded in 1999, with the commissioning of a second 35 MW DC arc furnace. Despite the fact that ilmenite smelting poses a technical challenge in terms of the high temperatures required, the physical characteristics of the slag, the constraints placed on the feedstock, and the tight product specifications, Namakwa Sands has continually increased slag production since 1995. High furnace feed-on utilisation and furnace stability, complemented by continuous improvement drives, will be the vehicle to drive performance in the short term, with longer-term performance enhancements due to strategic process development.

Jan 1, 2006

By M. Machikicho, N. R. Shoko, J. Chirasha

Keywords: Pyrometallurgy, furnace, ferrochromium, alloys, Zimbabwe Zimbabwe Alloys was founded in 1949 by a consortium led by the John Brown Group. It was the first ferrochrome plant in Africa. The establishment of the refinery was necessitated by an increase in world stainless steel demand and the need to reduce cost by shipping alloy rather than chrome ore. The location of the refinery in Gweru was influenced by a number of factors, not least of which were the abundance of chrome ore deposits, access to inexpensive power from Kariba, the availability of reductant coke from Hwange, accessibility to ports (as the town was well served with rail and road networks second to none in the country), and of course cheaper labour costs. The production of Low Carbon Ferrochrome (LCFeCr) was commissioned in 1953 and produced from an Open Arc Furnace with a Submerged Arc Furnace producing Ferrosilicon Chrome (FeSiCr) that is used as a reductant in the production of LCFeCr. An experimental furnace was commissioned in 1958 to help with efficiency and control on larger furnaces. A second Submerged Furnace was commissioned in 1963. Three other Submerged Arc Furnaces were built between 1967 and 1974. Several mines were acquired between 1974 and 1984, as a strategic move to ensure the growth of the refinery. A briquetting plant was commissioned in 1977, enabling the use of friable ores to enhance the capacity of ore supplies and ore cost management. A plant to recover alloy from slag was established in 1994 to capitalize on market demand without large capital outlay that would be required to build other furnaces to increase capacity. Zimbabwe Alloys has created employment opportunities throughout the years. There have been direct employment opportunities at both the refinery and the mining divisions. With time, indirect employment was realised both upstream and downstream of the refining process, enhancing the livelihood of numerous people. Zimbabwe Alloys' involvement with various labour skills has, of necessity, enabled it to develop a culture of safety at work, home, and play. Zimbabwe Alloys has contributed to society by participating and funding various local initiatives primarily to impact positively on societal needs. The latest development was in 1996, when Zimbabwe Alloys entered into a Technical Transfer Agreement with Japan Metals and Chemicals to improve the efficiencies and hence the profitability of the LCFeCr production process. A significant quantity of various alloys has been produced since inception, and significant foreign currency has been earned for the country. This was in spite of challenges that included the cyclic nature of market prices, the upheavals of sanctions affecting the macro-economic environment, and the challenges related to the deteriorating grade of chrome ore and reductant coke.

Jan 1, 2006

By L. Andrews

Keywords: mineralogy, phase-chemical, chemical-looping combustion, XRD, SEM, EDS, QEMSCAN, PGM, slag, matte, ilmenite Mineralogy, traditionally associated with concentrator studies, is being increasingly applied to problems in pyrometallurgy. Such investigations commonly make use of a number of techniques, and the results are combined for a meaningful interpretation, which can lead to a successful solution. Mineralogical applications are described from pyrometallurgical operations. Examples are given of studies and investigations involving mineralogy in chemical-looping combustion, feed monitoring to platinum-smelting furnaces, and losses to slag in base metal and platinum smelting.

Jan 1, 2011

By P. J. Knottenbelt

Outcomes from a workshop organized through the SAIMM revealed that the minerals and metals industry must develop its ?Engineering Team? if it is to continue to meet the challenges of globalization. The very economy of the country is largely dependent on a competitive and stable engineering team within the minerals and metals sector. With the Chamber of Mines (COM) passing on its education and training initiatives to the industry, the professional bodies like SAIMM must (despite meagre resources) continue the good work done through the COM in the past. The workshop highlighted recruitment and selection, further/higher education, socialization and initial training, deployment and retention and continuing education as priority areas. These are further detailed in this report. Office Bearers have considered the outcomes and the areas where the Institute should or should not be involved have been stated.

Jan 1, 2002

By S. A. Aye

Vibration levels on a variety of equipment in a South African opencast mine were measured in this study. The well-established ISO 2631-1 (1997) standard methodology was used for the computation of weighted root mean square (WRMS) and vibration dose value (VDV). This method was used to evaluate the whole-body vibration (WBV) on a wide range of equipment in the opencast mine using the two main parameters, namely the daily exposure A(8) which is based on the WRMS concept and the VDV which measures shocks. The results obtained show that while the majority of the equipment rendered exposure levels that are below the exposure limit value (ELV), exposure levels on about half of the equipment do exceed the exposure action levels. The study also highlights the importance of shock in the observed responses.

Jan 1, 2011

The roasting of sulphide ores and concentrates is often the first step in the production of metals or chemicals. In many processes, the production of sulphuric acid is viewed as a by-product, whereas in some plants production is an important economic factor. Regardless of the purpose, a pyrite roasting plant consists of mainly three plant sections: roasting, gas cleaning and sulphuric acid. With the addition of air, the pyrite concentrates are transformed into solid oxides and gaseous sulphur dioxide at temperatures of 600?1000°C. After cleaning and cooling, the sulphur dioxide in the roasting gas is further processed to sulphuric acid. Two types of reactors are used depending on the application: stationary or circulating fluid bed. For over 60 years, Outotec has progressively been developing the principle of fluidized bed technology in several different reactor types for a multitude of process applications. The versatility of the fluidized bed reactor system has manifested itself in the treatment of minerals, including solid fuels, and for metallurgical processes both in the ferrous and non-ferrous fields. Process applications have included roasting, calcining, combustion and charring of coals, as well as off-gas treatment. This paper provides a summary of the pyrite roasting technology currently used along with a simple cost comparison of pyrite roasting and sulphur burning processes.

Jan 1, 2009

By D. A. Spencer, L. J. Gardner

In light of the apparent productivity benefits provided by mechanised stoping, Impala Platinum Limited commissioned a study to investigate its possible implementation for mining reserves located 1200 – 1700 m below surface. This paper records the methodology employed for designing a support system for such mechanised mining, as well as initial conclusions of the work done. Preliminary results show the concept to be technically feasible; work was however stopped due to financial non-viability. En considération des bénéfices de production apparents que donne l’exploitation par gradins mécanisée, Impala Platinum Limited a commissionné une étude visant à examiner sa mise en œuvre possible pour des réserves minières situées à 1200 – 1700 m sous la surface. L’étude présente rapporte la méthodologie employée pour créer un système de support pour ce genre d’exploitation mécanisée, ainsi que les conclusions initiales de ce projet. Les résultats préliminaires montrent que le concept est techniquement faisable ; cependant le travail fut arrêté à cause de difficultés de rentabilité. Im Licht des offensichtlichen Produktivitätsnutzens auf Grund mechanisierten Stossbaus, kommissionierte Impala Platinum Limited eine Studie, die dessen mögliche Implementierung für den Abbau von Reserven 1200 - 1700 m unterhalb der Oberfläche untersuchen soll. Dieses Elaborat dokumentiert sowohl die Methode die für das Design eines Unterstützungssystems für eine derartige mechanisierte Abbauweise angewendet wird als auch die anfänglichen Konklusionen der geleisteten Arbeit. Anfängliche Resultate zeigen daß das Konzept technisch durchführbar ist; die Arbeit wurde jedoch wegen der finanziellen Nichtrealisierarkeit gestoppt.

Jan 1, 2003

By T. van Heerden

A range of supported gold catalysts was prepared by ion exchange, varying many of the preparation variables, including concentration in the precursor solution, washing procedure, as well as drying and calcination procedures. These catalysts have been characterized extensively. TEM images show essentially the same crystallite size distributions, between 2?5 nm, for almost all catalysts, the only exception being catalysts not washed in ammonia, which did not show any small crystallites. Additional characterization with SEM yielded an interesting discovery. Catalysts that appear identical on the TEM also contain some large crystallites in the range of 50?500 nm. Differences in dispersion due to the drying procedure not seen on the TEM can now be observed. Oxygen chemisorption is being investigated as an additional method to characterize gold based catalysts to complement the typically used electron microscope techniques.

Jan 1, 2012

By C. Sarkar

Increased competition in today’s global economy has put mineral industry under excessive pressure to effectively manage production assets to generate business wealth. Capital intensive industry (CII) organizations are seeking ways to manage skill resources, internal processes, and organizational networks with a view to reduce the cost of ownership of assets and increase efficiency of operations and service. The emerging concept of Enterprise Asset Management(EAM) is a collection of business processes that allow CII with right focus on return on investment on assets, to make right decisions on planning, acquisition, maintenance, operation, rehabilitation, and disposal of assets. Information technology (IT) can drive significant returns if the infrastructure covers seamlessly all business processes and all systems, like geographic information system, maintenance management, investment management, laboratory information management, and supervisory control and data acquisition system. The simple approach to IT in the past with disconnected silos of technology, information, and business processes cannot deliver the expected benefits under the modern business environment. Identification of business and application component is a prerequisite for the development of an asset management system that links effectively disciplined processes having characteristics of agility, speed, and integration. This paper discusses various issues and outlines the steps for developing an asset management roadmap in an organizsation. It also presents major business and application components of the system. Keywords: Enterprise asset management, Business architecture, Business component, Application component, Asset ownership, Asset operations, Information technology, Capital Intensive industry

Jan 1, 2003

By W. G. Huang

To recover the coal resources of high-sulphur anthracite in Jincheng Mining Area, underground coal gasification (UCG) of No. 15 seam in Fenghuangshan Coal Mine was proposed. The feasibility of the project was confirmed by investigations of occurrence conditions, coal properties, and roof conditions, as well as experimental studies and theoretical analysis. It was found that UCG technology is appropriate to be adopted in the mining of the No. 15 seam, due to the stable rock conditions, simple geological structure and hydrogeology, the high carbon content of the coal, non-cohesiveness, medium-thermal stability, high ash fusion temperature, and weak reactivity with CO2. Further factors are the characteristics of the immediate roof, which consists of 9.11 m of limestone and mudstone with a compact structure and low permeability, and 4.27 m of dominantly mudstone with low permeability.

Jan 1, 2012

By P. Rosario

The application of high pressure grinding rolls (HPGR) has been growing in the mining industry for the last 10 to 15 years. The major benefits supporting this trend are better energy efficiency, improved grinding capacity, and higher metal recovery in downstream processes such as heap leaching and flotation. In general there is limited quantitative knowledge on the true benefits of HPGRs relative to SAG mills in comminution, and about which situations one deals with better than the other. This paper will present a structure for comparison of the energy requirements for HPGR versus SAG mill considering complete circuits for comminution of precious and base metals hard ores. The work presented is from the design of four complete circuits based on ore data from two sites.

Jan 1, 2010

By G. A. Bezuidenhout, J. P. T. Kapusta, D. K. Chibwe

"Peirce-Smith converters (PSCs) are extensively used in the copper, nickel, and platinum group metals industries. The typical converting operation involves lateral purging of air into molten matte through a bank of tuyeres. This blowing operation occurs at low pressure from the blowers, resulting in a bubbling regime that is considered inefficient from both a process and an energy utilization perspective. Inherent drawbacks also include recurrent tuyere blockage, tuyere punching, and low oxygen efficiency.Western Platinum embarked on a full-scale industrial evaluation of generating a jetting regime by using sonic injection. Prior to industrialscale tests, a numerical assessment to ascertain the feasibility of implementing sonic injection into a PSC was conducted. The work included flow characterization at high-pressure injection achieving sonic velocity at the tuyere exit. The 2D and 3D simulations of the three-phase system were carried out using the volume of fluid method together with the RKE turbulence model to account for the multiphase and turbulent nature of the flow.This paper discusses the key findings in understanding plume extension, velocity distribution, shear wall stress analysis, and phase distribution characteristics in the system. Plant trials are also discussed with reference to the commercial aspects of a full-scale implementation of sonic injection in the smelter."

Jan 1, 2015

By D. J. Steynfaard

Sishen Iron Ore Mine is situated 280 km north-west of Kimberley in the Northern Cape Province of South Africa. The mine produces and sells high quality iron ore of various specifications to various national and international clients. The saleable product is derived from the blending and beneficiation of different types and qualities of hematite iron ore. This paper documents the new developments which were implemented (or are in the process of being implemented) on the mine in the long-term planning, medium-term planning, grade control and material tracking in the beneficiation plant with special attention being paid to the quality of the final, saleable product. The process starts with the long-term planning where the pit shell and pit optimization is determined by Whittle 4X. New developments include the introduction of a linear programming based scheduling system to enhance the long-term schedule generated by Whittle 4X. The LP route was decided on in order to take into account all the constraining factors of the final product that could not be configured in Whittle. To complement this the XPAC Auto Scheduler scheduling package was introduced to do the medium-term mine scheduling. This 18-month rolling plan includes cost parameters to enable the planner to extract a detailed operational budget from the scheduling while ensuring that production standards are maintained and grade constraints are met. The existing grade control system was enhanced with GPS capabilities and a computer system to do material tracking. The high precision GPS system introduced on the shovels allows for the accurate control of the loading procedures at the mining face. Because of the complicated geology and grade composition of blasting blocks it is imperative to accurately differentiate between different materials in the same blasting block and being able to excavate that with the loading equipment. The GPS system on the trucks allows for accurate location monitoring of dumping in order to keep track of specific material types. The state-of-the-art material tracking system developed for Sishen will enable the grade control officer to keep track and record various parameters of the material from its in situ position in the blasting blocks, through the crusher and onto different stockpiles, in various stages of the beneficiation process and onto the blending beds, into the dispatching trains and eventually into the ships for international distribution. These developments elevate the Sishen planning and grade control systems to a new level of service excellence from which management can obtain accurate and timely information on product status. It also enables Sishen to maximize resource utilization while still complying with the tough market constraints.

Jan 1, 2003

It is estimated that the tailings dam of the Mouteh Gold Mine, in Iran, contains more than 770 kg of gold. Microscopic analysis reveals that sulphide minerals and active carbon are the main sources of the gold in the tailings residue. Flotation and cyanidation tests on the samples of tailings were conducted. Flotation concentrates, containing around 87.79% of the gold, which were associated with sulphide minerals, were recovered. By regrinding, roasting, and cyanidation of the flotation concentrate, the gold dissolution recovery was in the range of 87.8 to 98.4%. The carbon-in-column method was used to recover 98% of the gold from the solution. Keywords: gold ore, pyrite, flotation, roasting, cyanidation

Jan 1, 2009