Search Documents

By J. Meintjest

As you pointed out, furnace power factor (and consequently transformer MVA rating) depends upon the inductive reactance, and so it is desirable to design for the lowest possible value of this parameter. The further introduction on the primary side of the transformer of capacitors, whether in shunt or in series, increases the network power factor but does not alter the furnace power factor; that is, the phase angle between electrode to- hearth voltage and current remains unchanged. Corrigenda The following amendments should be made to the article entitled 'Coal-preparation routes for maximum coal recovery', which was published in the August issue (vol. 80, no. 8) of this Journal:

Jan 1, 1980

By A. R. Barnes, C. W. P. Finn

The prereduction and smelting characteristics of UG-2 ore were studied and compared with those of Winterveld chromite ore. The UG-2 ore proved more reducible, and substantial prereduction (over 70 per cent reduction after 30 minutes at 1250oC) was obtained. No difficulty was experienced in the production oh high-carbon ferrochromium alloy containing 48 to 50 per cent chromium. Calculations of the energy balance show that UG-2 chromite has lower total energy requirements (both on the basis of unit of ferrochromium produced and of total chromium content). More than 50 per cent of the energy required for reduction can be supplied outside the smelting furnace.

Jan 1, 1983

Results from a study undertaken at a Transvaal colliery on the feasibility of undermining an urban development by conventional bord-and-pillar mining operations in the No. 4 Seam of the Highveld Coalfield are discussed. Surface ground vibrations above production sections were measured, analysed, and then compared with well-accepted guidelines so that the expected effects of vibration on inhabitants and surface structures could be determined. The measurement and scaling of ground vibration from blasting are outlined, and the effects on humans and structures are discussed. It is concluded that residential areas can be safely undermined by conventional drilling and blasting techniques provided certain simple guidelines are followed.

Jan 1, 1987

By J. Jacob

Diamondiferous linear beaches in Mining Area No. 1 have been the mainstay of Namdeb?s diamond production for more than 80 years. Most of the onshore beaches have been mined out, but in recent years mining has been extended offshore into the surf zone through a process of beach accretion. A total of 61.6 million carats has been produced from the gravel beaches since their discovery in 1928, and Mining Area No. 1 is considered to have great remaining potential from areas currently submerged under water. To date, the surf zone has remained largely unexplored due to the consistently strong winds, currents, and large waves which make access to this area extremely difficult. This paper describes the processes used in developing a practical methodology for exploration of the surf zone in a domain extending approximately 22 km long in a northwest?southeast direction and 0.3 km wide in a perpendicular direction adjacent to the current Mining Area No 1. The vigorous surf zone poses multiple technical challenges in terms of obtaining geological and diamond information. In order to access the area for sampling, a jack-up walking probe drill platform (PDP) with a 5-inch diameter reverse-circulation drill has been developed to carry out exploration drilling in the dynamic surf zone. The hydraulically driven platform has eight legs, each of which is 18 m long. Four of the legs are in fixed positions on the fore and aft sides of the platform. The other four moveable legs are fitted to sliding frames attached to the port and starboard sides of the platform. The sets of fixed and moveable legs can be raised and lowered by hydraulically powered jacking stations. By alternately lifting and lowering the sets of fixed and moveable legs in conjunction with the frames moving back and forth horizontally, a walking action is performed by the PDP. The platform can walk at a speed of 10?15 m/h, depending on weather and footwall conditions. Optimization of sampling for diamondiferous gravel occurrence in Mining Area No.1 was undertaken through creation of a virtual orebody on which different sample configurations were tested. The input data for the construction of a virtual orebody comprises a set of drilling data, collected from recently accreted areas directly adjacent to the 22 km × 0.3 km target domain. The input drilling data covers only 34% of the domain, and for the purpose of this study, a single realization is deemed to be sufficient. The texture obtained from using only the drilling data to construct a simulation did not make geological sense; hence it was necessary to make use of analog data in order to improve the simulation. The first analog data used consists of the gully patterns found in the metasedimentary Precambrian bedrock footwall. Gullies are, in general, gravel filled and it is fair to assume that gully patterns form a subset of the total gravel occurrence. Total gravel occurrence includes marine terraces (governed by sealevel stands) above bedrock peaks, together with gravel within gullies below bedrock peaks. The second analog ?data? introduced is through the use of ?expert interpretation?. The indicator drilling data is interpreted by expert opinion and the 2-dimensional result is hand-sketched, digitized, and then pixelated. The pixelated data set is then used as input for variogram calculation. This study cannot provide a single definite optimization result as the nature of the data does not permit this. The use of different validation approaches (conditioning data, where available; expert interpretation; and gully pattern data), however, can give a very good indication of how to balance sampling effort with de-risking aspects related to geological continuity. Work undertaken by sampling the simulation will give an assessment of the relative probabilities of determining gravel occurrence in the study area. This study showed that a 50 m × 400 m cross-configuration will be a good initial sample spacing for highlighting areas where gravel may be absent, and further infill drilling may be required. The relative efficiency of a 50 m × 400 m cross off-set sampling configuration has been demonstrated using a trumpet curve versus sampling effort when using kriging as the estimation method. Keywords sampling configuration, marine diamonds, orebody simulation.

Jan 1, 2014

By A. M. Starfield

Discussion J. de V. Lambrechts (Fellow): The author's paper is a brilliant follow-up of an earlier paper by Starfield and Dickson.1 I have no quarrel with Dr Starfield's computerization of a complex problem, but I do not believe that he is getting quite the right answers from his programme. My impression is that his predictions about wet bulb temperature increases in very deep mines are over optimistic; in other words, that it will be hotter than Dr Starfield predicts. This is putting my views in a nutshell. This is not the occasion on which to indulge in lengthy argument about the original paper by Starfield and Dickson, but the present paper is, after all, based directly on that earlier paper and if the one fails, the other cannot succeed. I did level certain criticisms at the first paper and cannot say that the authors' replies were very convincing. I do not think it is a sin to admit that I belong to the old school which believes in thorough field experimentation and practical trials and no amount of mathematical manipulation or physical theorizing, no matter how excellent, can make up for inadequate practical confirmation. This, as I see it, is still the crux of the matter. The original paper by Starfield and Dickson still rests on somewhat scanty practical evidence and I would be much happier if Dr Starfield's computer programme, based on the Starfield-Dickson model, had been checked against a large mass of observations in the practical mining situation. This is what both Wiles2 and myself3 had tried to do previously. What we lacked in mathematics and/or computer aids, I think the present paper by Dr Starfield lacks in practical substantiation. This is no condemnation of the author's paper which, taken by itself, is excellent but I think the final stage is still lacking, namely the bringing together of theory and empiricism in a manner acceptable to all. This may be wishful thinking on my part but I hope, within the next year or so, to come up with a modified Starfield-Dickson model in such a way that the computer answers will agree in the majority of cases with the few hundred field observations which are already on record. It might be a case of applying the proverbial 'Cook's Law' to the Starfield-Dickson model! REFERENCES 1. STARFIELD, A. M., and DICKSON,A. J. 'A study of heat transfer and moisture pick-up in mine airways.' J. S. Air. Inst. Min. Metall., 68, (5), 1967. 2. WILES, G. G. 'Wet bulb temperature gradients in horizontal airways.' J. S. Air. Inst. Min. Metall., 59, (7), 1959, p. 339. 3. LAMBRECHTS, J. DE V. 'Prediction of wet bulb temperature gradients in mine airways.' J. S. Air. Inst. Min. Metall., 67, (11), 1967, p. 595. R. Hemp (Visitor): Dr Starfield's paper has very effectively rounded off one particular aspect of the general problem of heat flow in mines. The ease with which this computer programme can be used to calculate temperature increases in horizontal airways must lead to its wider use in ventilation planning and, in developing this rapid method, Dr Starfield has indeed rendered a valuable service to the mining industry. One could consider further instances of heat flow in airways in which the availability of a rapid computer method would be desirable, e.g. the flow of air down a shaft, where there is an increase in temperature due to adiabatic compression, as well as an increase in virgin rock temperature as the depth increases. However, this particular case would not present any new problems and would merely require an extension of the exisitng work. I should like in this contribution to talk about an aspect of environmental control in mines which, I think, will become more important in the future. It is well known that wet bulb temperatures are subject to fluctuations underground. In some instances, particularly in stopes, the fluctuations, both with time and position, can be considerable. The theoretical work which has been carried out on temperature increases has been aimed at the prediction of mean temperatures, and no account has been taken of fluctuations around this mean. It is questionable whether this approach will, on its own, be sufficient, particularly when temperature increases in stopes are considered. The fluctuations in air temperatures underground arise from two causes. The first of these would be the fluctuations in surface conditions, and here one could list random, diurnal and seasonal fluctuations. The second cause is the multitude of things which vary in a mine and here one could list variations in air flow quantity, sources of evaporation, heat transfer from pump and compressed air columns and, particularly in the stope, variations in air flow patterns. Fluctuations arising from surface temperature variations should be amenable to calculation, and here one envisages figures relating the decay of temperature variation with distance to factors such as air flow quantity. Fluctuations resulting from changes in the mine are perhaps more difficult to tackle theoretically and the best approach could well be to analyse underground observations. In this connection, there is a good case to be made for the increased use of statistical methods in the analysis of underground temperature measurements, and it might be of value to look at current air-conditioning practice. When carrying out cooling load calculations for a particular location it is customary to use design wet bulb

Jan 11, 1969

By F. L. D. Cloete

The following discussion relates to the paper by G. S. Hansford, C. D. Levy, and J. W. de Kock that appeared in the March 1976 issue of the Journal (vol. 76, no. 8, pp. 363-369) Competition for student members Each year the South African Institute of Mining and Metallurgy offers a prize (or prizes should the entries warrant it) of up to RI00 for the best paper or dissertation on a topic appropriate to the interests of the Institute. Engineering in South West Africa The SW A Engineering Profession Steering Committee was established on 4th April, 1977, its purpose being to formulate an Act covering the engineering profession in South West Africa.

Jan 1, 1978

By A. Koursaris, Y. N. Turan

This paper reports the results of a literature review carried out on nitrogen-alloyed austenitic stainless steels and their properties. It was found that a large volume of work has been carried out on the subject, particularly with regard to the more common stainless steels such as types 304 and 316. No work appears to have been conducted on the highly alloyed steels such as type 310S. Nitrogen has been found to increase the stability of the austenite in stainless steels and to impart significant improvements in the mechanical and corrosion properties of these alloys. Importantly, nitrogen appears to increase both the ductility and the strength of austenitic stainless steels over a wide range of temperatures.

Jan 1, 1993

By R. S. Francis

There are no manuals or handbooks for budding mill superintendents or process plant managers. Most who obtain this level of responsibility have gained their training from watching the good and bad of their predecessors and the successful ones have themselves graduated from the school of hard knocks. This paper attempts to provide some helpful guidelines and direction for those who aspire to better manage a mineral processing facility. The authors have 20 years combined experience in senior management roles at nine different mineral processing operations in Australia and overseas, covering gold, base metals and mineral sands. This summary of tips and pitfalls will hopefully benefit future leaders in mineral processing and metallurgy.

Jan 1, 2007

By D. Clement

A comparison between hydraulic and pneumatic rockdrills by D. CLEMENT The regulation of compressed-air reticulation systems is very poor compared with that of electrical systems; this means that electrohydraulic rockdrill systems offer greater flexibility, additional power being readily available at the working face. Hydrometallurgy A new journal devoted to all aspects of the aqueous processing of metals is scheduled to appear this year. Entitled Hydrometallurgy, the journal will be published in quarterly issues, one volume per year. Mineral dressing Contributions are invited for the Symposium on Recent Progress in Mineral Dressing in South Africa, which is to be arranged jointly by the South African Institute of Mining and Metallurgy and the National Institute for Metallurgy. Mineraalbereiding Bydraes word verlang tot die Simposium oor Onlangse Vordering met Mineraalbereiding in Suid-Afrika wat gesamentlik deur die Suid- Afrikaanse Instituut vir Mynbou en Metallurgie en die Nasionale Instituut vir Metallurgie gereel gaan word. Rock mechanics The Sixteenth Symposium on Rock Mechanics is to be held at the University of Minnesota from 22nd to 24th September, 1975. The Symposium is the official Symposium for 1975 of the International Society for Rock Mechanics (I.S.R.M.), and the Council for I.S.R.M., consisting of members from 25 countries, will meet during the Symposium. Powder metallurgy The annual meeting on powder metallurgy organized by The Metals Society is this year to be held at the Stratford Hilton Hotel, Stratford-upon-Avon (the notification did not include the date of the meeting). Vacation School The South African Institute of Mining and Metallurgy has great pleasure in announcing its intention of holding a vacation school on the topic of electric-furnace melting. NIM reports Report no. 1681 The determination of sulphur and phosphorus in chromite. Report no. 1687 The viscosities and electrical conductivities of slags associated with the production of high-carbon ferromanganese alloys.

Jan 3, 1975

By R. J. Davidson, V. Veronsee

Some of the parameters affecting the elution of gold from freshly loaded activated carbon using pure water as an eluant were studied. The procedure involved pretreatment of the gold-loaded activated carbon with a strong reagent of sodium cyanide and sodium hydroxide, followed by elution of the gold with water. Gold-loaded carbon obtained from three different sources was studied. It was shown that the elution temperature was the most critical parameter, and column operation at I !OCC (gauge pressure of 50 to 100 kPa) is suggested. The effects of variations in the concentration of sodium cyanide required for the pretreatment of loaded carbon and of variations in elution flowrate were also investigated. Both these parameters were found to have only a marginal effect on the efficiency of gold elution. The investigation also indicated that gold-elution rates were affected to a considerable degree by the particle size of the carbon concerned. Higher elution flowrates could be used when carbons of finer particle size were eluted. A modified eluate-collection procedure was also developed during the course of the investigation. Oven-drying of the loaded carbon was shown to have little or no effect on the efficiency of the subsequent gold elution. The calcium and silica contents of the various carbon samples were also determined. It was immediately evident that the calcium content was very considerable in the case of loaded carbons originating from carbon-in-pulp operations. Calcium concentration was particularly high where air agitation had been employed in the carbon-contacting circuit. To some degree, the calcium build-up explains the serious carbon fouling taking place, resulting in a decreased efficiency of gold adsorption. The fouling problem was found to be less severe when mechanical agitation was used. No poisoning by calcium carbonate was observed where the pregnant solution had been acidified before it was contacted with the carbon.

Jan 1, 1979

1. Recent publication Iron and steel works of the world. Worcester Park (England), Metal Bulletin PLC, 1987. 9th edition, 728 pp. £94.75 by air mail.2. Canadian publications Mining and mineral processing operations in Canada, 1987. Mineral Bulletin MR 216. $15. (Obtainable from Printing and Publishing, Supply and Services Canada, Hull, Quebec, KIA 059 Canada.) Peat producers in Canada, 1986 directory, by M. Prud'homme. MRI 87/7 Canadian mines: Perspective from 1986. Reserves, production capability, exploration, development. Mineral Buletin MR 215. $9.95. 3. Mintek publications Report M313 The testing of abrasion resistance in pipeline materials, by D.P. Enright. Nov. 1987. 36 pp. Report M328 The installation and commissioning of a Hilger Monospek D500 scanning monochromator, by A.E. Watson. Sep. 1987. 11 pp. Report M331 The design and operation of hot-air dryers for the drying of granular activated carbon. Nov. 1987. 30 pp. Report M338 Ore microscopy, image analysis, and the extractive metallurgy of sulphide minerals-an overview. Nov. 1987. 14 pp. Report M339 The determination, by flow-injection analysis, of sulphate in solutions containing chromium(I/I) and iron(I/I). Nov. 1987. 11 pp. Report M222D The simultaneous determination of common anions by ion chromatography, by A. Cameron and C. Pohlandt. Oct. 1985, reissued May 1987. 10 pp. Report M227D The spectrophotometric determination of silica in metallurgical-grade fluorspar, by M. Solomons. Nov. 1985, reissued Jun. 1987. 9 pp. Report M229D The determination of metalic iron in prereduced iron ores, by R. Lownsbrough. Dec. 1985, reissued Jun. 1987. 7 pp. Report M252D The spectrophotometric determination of bismuth in sulphide materials, by M. Solomons. Mar. 1986, reissued Jun. 1987. 13 pp. Special Publication no. 12 Platinum in South Africa, by A.M. Edwards and Silk. 1987. 64 pp. Illustrated in colour. R30 ( Africa), US$30 (other countries). 4. Journals of interest Industrial Minerals. London, Metal Bulletin Journals Ltd. Tin and its uses no. 154, Nov. 1987.

Jan 1, 1988

By L. Morin, S. Mortazavi, K. Volchek, A. Demers, A. Di Feo

The objective of this paper was to investigate the possibility of reducing process (fresh) water and increasing recycled water (thickener tank overflow water). As part of the investigation, rougher flotation tests were done with the two water types and a mixture of the two (50%/50%). The effect of recycled water on the grade-recovery response and rougher recoveries was investigated. When thickener tank overflow was used (50% and 100%), the nickel+copper grade versus nickel recovery decreased. The decrease in the grade-recovery was due to higher pyrrhotite recovery. Also, there were no effects on nickel and copper recoveries, which was confirmed using multivariate statistical analysis at the 95% significance level. Keywords: Flotation, nickel, copper, water recycling, multivariate statistical analysis, MANOVA, reverse osmosis

Jan 1, 2020

By J. S. Preston

The properties of some recently developed solvent-extraction reagents for the separation of cobalt and nickel sulphate solutions are reported. New commercial extractants based on alkyl phosphonic and alkyl phosphinic acids are described. These reagents show much improved selectivity for cobalt compared with established extractants. Some novel extractants developed at Mintek for the selective recovery of nickel in the presence of cobalt are also described. These reagents, which are based on mixtures of carboxylic acids and non-chelating oximes, are of interest in that no commercial nickel-selective reagents are currently available. Graphs showing metal loading and stripping, and pH-functionality, are presented. together with details of the metal separations achieved in batch countercurrent- extraction experiments with the various reagents.

Jan 1, 1983

Minerals and Manpower - PRESIDENTIAL ADDRESS given by R. P. Plewman, Pr. Eng., B.Sc. (Eng) (Wits), M.A. (Oxon.) INTRODUCTION What I want to discuss is the future pattern of manpower in the mining industry, and I should like to begin by examining some relevant statistics. There are four areas that must be examined. Firstly, the future rate of production of different minerals must be estimated. Secondly, an assessment must be made of the balance of different mining technologies likely to be used for each mineral. Thirdly, the manpower requirements for each technology must be determined. And, fourthly, the future manpower resources of the country must be explored. NIM report Report No. 1646 Examination of the methods of analysis for calcium fluoride in fluorspar.

Jan 10, 1974

By M. A. Ford

This paper reviews the history, sources, mineralogy, extraction metallurgy, conversion, and enrichment of uranium in South Africa. Over the past 40 years extraction plants were built at 27 sites, an9.over 140 kt of uranium have been produced. Older plants have had to adapt to changing market conditions, no single technology has had the opportunity to become entrenched, and costs have been reduced to a third of those of the original flowsheet. The research efforts aimed at developing the country s nuclear raw materials have been particularly rewarding, as they have enabled South Africa to become a world leader in the extraction of uranium from low-grade ores and to develop methods for uranium enrichment and the production of nuclear fuels.

Jan 1, 1993

By k. Lebecki, S. Trzcionka

The prototype and test results of the instrument for quick determination of incombustible content in deposited dust as a protection against coal dust explosion propagation are presented. Presently existing methods do not permit to obtain quick information about incombustible content, needed for the proper protection of workings. As the operating principle for the e instrument the dependence of reflection of infrared radiation intensity on incombustible content in the sample is chosen. The construction is based on the modern electronics. The measurement will be done at the sampling site. The range of the instrument is 0-100% of incombustible, direct reading, autonomous supply, weight no more than 0.5 kg, and is intrinsically safe according to EN Standards. During the Conference the instrument will be commercialized.

Jan 1, 2003

By B. Kenealy

A typical deep shaft is President Steyn No. 2 in the Free State, where 9 tonnes of ore are hoisted at about 15 metres per second from 2378 metres below surface. The skips and attachments each weigh 7 tonnes and they are connected by 43 tonnes of rope, so that to hoist the 9 tonnes of payload, a total of 66 tonnes is accelerated from stand still to 55 km/h for each cycle, using an average of 3185 kilowatts of power in the process. The cycle time for the hoisting is 3.22 minutes. The peak power consumption is 6954 kilowatts, which determines the size of the motor used. Is this the right approach? Are larger skips moving at higher speeds the answer? Is there another way?

Jan 1, 1996

By M. Wu, X. Zhao

This paper presents an integrated pipeline transport system for thickened coal sludge, which combines pretreatment and pipeline transport with combustion techniques of thickened coal sludge. The pipeline can transport thickened coal sludge with a sufficiently high solids content (about72%?77%) and high apparent viscosity (about 1 000Pa?S?3,000 Pa?S) directly by pipeline having neither use for water nor an addition agent. The transport distance can be as high as 1 000 metres. In particular, the operating principles, key equipment and technical parameters of this integrated system are examined in this paper. The integrated system effectively causes no pollution to the environment because it is completely sealed, and conserves energy over traditional conveyer designs. Keywords: pipeline transport; integrated system; circulating fluidized bed boiler; thickened coal sludge; high solids content

Jan 1, 2007

By A. V. L. Narasimham

The practice of refractory lining in Fe Cr furnaces is purely based on the behavior of various refractories used in different parts of the Furnace at elevated temperatures. The choice of the pattern of lining is mostly done on traditionally based concepts. Refractory Lining of a furnace is the most crucial enabler for operational excellence for Ferro Alloys production. During the last few years, no major technological change has taken place in ?Refractory Lining Management?, only freeze lining concept is becoming popular. Many ferro chrome furnaces today, have the refractory lining problems especially at tap holes, resulting in shutdowns and production losses. The author with his experiences for the last 37 years in furnaces of all sizes tried to attempt to investigate into the reasons for premature failure of lining.

Jan 1, 2007

In a gold CIP/CIL circuit, adding new circuit water to a final tails thickener and then directing the thickener overflow to the head of the circuit significantly reduces the cyanide concentration at the TSF discharge spigot. The new water is used to dilute the final tails. The dilution and recycle of the tails in this manner may have the added benefit of reducing reagent consumption, in some cases to the point where the reagent savings justify the expenditure and Cyanide Code compliance is achieved at no extra cost. Potential circuit configurations and water recycles can be modelled by splicing a flowsheeting and thermodynamics package, such that changes to the composition of the water can be reduced to chemical speciation with a Gibbs free energy minimisation enabling a complete understanding of the circuit water chemistry.

Jan 1, 2007