Search Documents

By Geo. A. Brown

This paper was written from conditions existing in the Cumberland Mines of The Union Pacific Coal Co., with my impressions and cause of same. These mines are located on a branch line of the 0. S. L. R. R., about sixteen miles south of Kemmerer, Wyoming. The mines are the property of The Union Pacific Coal Company with headquarters at Rock Springs, Wyo. There are two mines, No. 1 and No. 2, located about two miles apart in a seam of coal averaging about 16 feet thick which is split with a parting of rock from 4 feet to G feet from the bottom, averaging from 4 inches to 5 feet thick, mostly of soft fire clay, with an average pitch of 21 degrees to the west. The lower coal below the fire clay band being of a soft nature, much softer than the coal above it. The cover or roof next to the coal is of a massive sandstone formation from 4 feet to 60 feet thick while the floor of the seam is of a soft fire clay as far down as has been prospected. These mines are also of a dry and dusty nature, they generate lots of fire damp and are subject to fires from numerous causes. These mines were opened up in 1900 with five openings each, Main Slope, North and South Manways and North and South Aircourses driven parallel directly on the pitch of the seam which is fairly regular, entries being turned North and South at right angles off the slope about 300 feet apart. The entries were driven double 10 feet wide with chain pillars from 20 feet to 30 feet thick. The main entries are used for haulage and main intake, back entries for return aircourses. Rooms are turned on 50-foot centers and 20 feet wide, directly on the pitch Galvanized sheet iron chutes are used in the rooms. The slopes were driven down in No. 1 mine about 4,000 feet, in No. 2 mine about 5,000 feet where the cover would be about 1,400 feet in No. 1 mine and about 1,700 feet in No. 2 mine approximately. When a point about 2,000 feet on the slope had been reached with cover, 600 or 700 feet squeezing became noticeable on the entries and room pillars with slight bumps which extended clear to the upper entries of the mines and continued to get worse as the mines got deeper and with more cover as no pillars had been removed at this time. It should be stated here that faulty ground was found on the south side of No. 2 mine and on the north side of No. 1 mine, in some places looking like a fault of a down throw, some places like a want and other places like an erosion. The latter theory seems to be correct from prospecting and drilling. The mining of entries and rooms became more difficult with more squeeze and bumps of increased pressure which closed entries and aircourses and finally caused the lower workings of the mine to be abandoned. It was then decided to open up the entries from the 6th up, or approximately half way up the slope. The opening of these entries was started with the intention of extracting pillar coal but considerable danger was met with for the entries .were squeezed tight and when they were disturbed, bumps and squeeze conditions had to be contended with, also gas and fires due to the continued grind on the pillars due to overhead pressure bringing on friction which caused innumerable fires to start in the bottom coal. Bumps being so extensive at times as to close up aircourses for 500 or 600 feet, also discharge timber, coal and rock from the rib of slope and entries for hundreds of feet, dislodging tracks and throwing mine cars around just as if an explosion had taken place, filling places with gas and throwing dust into the atmosphere so that you could cut it with a knife. It became necessary to discontinue the use of black powder and naked lights entirely as a safety precaution. Permissible Powder Monobel No. 5 and Wico Electric Safety Lamps were installed. All coal was shot off the solid whenever it was necessary to shoot. ' In opening up these entries it was found that practically all of the weight was centered on room pillars up to the first crosscut chain pillars and barrier pillars between top of rooms of entry below and the one above which averaged 30 feet thick and in all practically 120 feet of ground. The rooms were mostly open from the first crosscut up to the face which showed that the points mentioned had taken the weight. It was found impossible in some of these entries to drive double entries again as the bumps and squeeze made it impossible to maintain them. This made ventilation quite a problem, small booster fans and flexoid tubing being used for ventilation until one entry could be connected with the one above which has solved most of our ventilation problems so far.

Jan 1, 1924

By J. H. Emrick

When I was asked to read a paper to you, I wondered what idea I could bring before you which would be interesting and which would be helpful in your work in operating coal mines. The Institute has been studying ways and means of increasing the safety and efficiency of mine operations. Almost every subject along this line has been discussed from time to time. In thinking the matter over it occurred to me that there was one thing used by practically all coal mining companies in considerably large quantities and which in many cases does not receive the attention it should. It is the cutter bit placed in the cutter chains on coal mining machines. Coal mining machines have been repeatedly improved during the last twenty-five years until their efficiency and convenience have reached a high level. The generating units making electrical power to operate them also have been developed to a similar degree. This machinery has been in- stalled at a great expense to coal mining companies and the installation made for the sole purpose of pulling coal cutter bits through coal. Why not then give these cutter bits some attention so as to see that they do their work as efficiently as their driving and propelling units? The consideration of this question easily divides itself into three principal parts-First, the kina of steel out of which to make the bit; Second, the proper form or shape to give it; and Third, the tempering of the bit. Let us discuss them in that order. There have been tried at different times' various grades of steel for cutter bit uses. The cheaper steels, having a very low carbon content (.10 to .30 per cent carbon) have proved un- satisfactory because such steel cannot be tempered so as to produce a satisfactory cutting tool. Because of the low carbon content, it cannot be hardened to retain its cutting edge. It dulls quickly, bends easily on striking any hard obstruction in the coal, and so requires constant resetting to its original form. The high priced alloy steels when properly shaped and tempered will give a bit that would make a clean, even cut in the coal if no impurities were encountered. Such a condition is rarely found. Alloy steel is quite brittle and on striking impurities, such as sulphur balls or a sand spar, is readily broken and so the loss of material through these broken bits and the high price paid for it more than offset all the other advantages which this steel has shown in cutting. Experience has shown that steel having approximately .70 per cent carbon and from .25 to .35 per cent manganese will give the most economical results. Some mines have obtained better results by using a steel of slightly higher carbon content and in some cases a grade of tool steel has been used. The disadvantage of using a steel having too much carbon is that it can easily be spoiled in the black- smith shop by overheating. Steels having a carbon content of about .70 per cent have a sufficiently wide range of temperatures at which they can be forged and hardened so that with ordinary care and attention they are not likely to be burned. Steel of this quality, therefore, has been found to be the most practicable because of its reasonable cost, ease in working and tempering and general durability. In the early days of mining machines, comparatively few bits were used because each machine required but a few bits because there were but

Jan 1, 1925

By Richard M. Whiting

Thank you very much for that introduction. I spent part of my early career in the coal industry here in Colorado, and I am always happy to return. In such a beautiful setting, it seems out of place to talk about "Improving the Climate". But in our work-a-day worlds, we know the climate for the coal industry is something less than picture perfect. But unlike Mother Nature's climate, there are some things we can do about the climate for coal. Today, I want to talk to you about sonic of the activities that we are engaged in... and that you can support... to improve that climate. A number of challenges and opportunities face our industry. I will try to set the stage for this conference by briefly describing the current climate for coal - which is indeed very challenging. I will then outline some of the steps we are taking to broaden our base to include our allies in the rail and electricity industries and the public at large.

Jan 1, 2000

By A. L. Jones

The subject assigned to me of "The Power" Problem of the Mine" is so broad that I have decided to confine myself to the question of the power supply itself, rather than the application of electricity throughout the property. We will look over certain economic aspects of the problem, particularly in the way it affects the mine manager or executive and his attitude toward the power plant. The accepted method of power application to the mine is by electric power, and the experience of each of you is that the job is never complete as you are always undertaking some further electrification which necessitates the stiffing up the power house to care for the additional load. The mine executive, then, is wrestling almost continuously with the problem of his power plant. Either it is overloaded and must be enlarged and rebuilt; or its operating costs are excessive; or it breaks down and limits coal output; or some one wants to sell new and improved machinery, until the manager almost hates the thought of such a restless part of his property. If he purchases power, every day new uses for it seems to be found. In many ways this unrest is due to short-sighted policy toward the problem, and the tendency when the problem of extension has to be met, to dispose of it in the cheapest way and without thought as to where the future is leading. The day when each opening had its own boiler plant, steam hoist, steam driven fans, steam pumps, steam loaders, etc., seems to be far behind us. The recognized method of power distribution today is by electric power, except for rather limited applications of compressed air; most of which is electrically compressed. During fifteen years contact with mines of Colorado and Wyoming the writer has seen nearly every mine power house double or triple in capacity or abandoned in favor of purchased power, worn. out and inefficient machinery thrown out, isolated boiler plants dropped, seam pumping at great depth changed to electric drive, all resulting in greatly reduced labor and fuel costs. Power costs, which in such isolated plants were considered normal, would be unthinkable today. One property where the main power supply was by compressed air from steam driven com¬pressors used under boilers 8.35 per cent of all the coal mined. The cost of power was 12 1/2 cents per ton of coal mined. Another property of four openings, each with its own boiler plant and usual equipment of hoists, pumps, etc., had a power cost of 10.3 cents for each ton mined; and these were days when you did not get very high prices for coal. Another property operating two mines mostly by steam used 11.1 per cent of the coal output under their own boilers and the power cost was 19.45 cents for each ton mined. Each of these properties is now electrified and power costs are from 3 to 4 cents per ton, and the fuel burned runs from 1 to 2 per cent of the output. With the broadening market and high prices for slack coal and the high prices for labor in boiler and engine rooms, the cost of steam is reaching a high figure, and efforts must be made to keep this down, by more efficient steam production and by utilizing this steam in better machinery which will increase the work done by each pound of steam. It must not be overlooked either, that the plant which is very wasteful of fuel is usually a pretty old one and one far from reliable. In a general way the more efficient the plant, the greater its reliability. Ample and reliable power supply means ability to get out coal when there is a market. The increasing use of purchased power is largely due to changing conditions which are tending constantly to push up the cost of power, unless the most efficient machinery is used and large scale production possible. The

Jan 1, 1923

By Steve Leer

Pick then introduced the convention keynote speaker, Steven Leer, President and Chief Executive Officer of Arch Coal. Following the morning coffee break, Pick introduced Howard Goodman to present the Fourth Annual Safety Awards. [ ]

Jan 1, 2001

By K. L. Marshall

A facetious title was purposely given this talk, so that a formal paper would not be expected. TWO or three days ago, while discussing with Mr. Dickinson some of the details of the dust explosion demonstrations we are planning for this coming Saturday, I remarked that we would like to have as many people as possible see some samples of 20 and 200 mesh dust, so they would more fully understand just what was causing the explosions. Mr. Dickinson requested that I bring samples and screens and in this informal manner, give you all a ".close-up" of coal dust which is considered in Explosion Hazard reports. While sampling mines, for road, rib, and roof dust, in connection with safety service and hazard reports which the Bureau of Mines Engineers make at the request of coal operators, I have often been assisted by under- ground mine officials or other men of many years experience and on almost every occasion, while we were carefully brushing the very fine dust from timbers or coal surfaces, they would make some remark such as: "never had noticed this kind of dust, didn't know it was here", or "well, that's the first time I really understood what all 'this dust talk was about." Such experience makes me believe that the much published terms, 20 mesh and 200 mesh are just numbers to the great majority of both miners and operators. We are now going to have lesson one in the primer of coal dust explosions and I want to say, in all sincerity that a complete course in the hazards of mining is deserving of a place in the curriculum of the best mining schools of this country. Sample No. 1 is fine coal and dust and is a fair sample of what can be found every where in rooms and entries of a mine, as it is too small to be gathered up with a shovel and is left in the ordinary mining at the faces and is spilled along the entries in haulage. In this you will see some quarter inch coal, much eighth and sixteenth inch coal, in fact those are the sizes I find many people have in mind when they are asked about the dust made in mining. Although the sizes mentioned are the ones which seem to almost entirely make up this sample, such is not the case, for from 10 to 20% of such a sample will usually pass this 20 mesh screen and in Sample No. 2 we have 20 mesh dust. Result of many tests, supports .the statement of the coal mining division of the Bureau, that it is quite probable that coal over 20 mesh does not take part in any but the most violent of explosions and that all dust under 20 mesh may take part in any explosion. The largest particles in this sample will not be over .03 inches in their largest dimension and a pound of dust to a foot of average heading is very easily found in most every mine I have visited and usually a great deal more can be readily gathered up. It was .found early that the finer the dust the more dangerous it was for a given coal. So for the early explosion tests conducted by the Bureau a commercial pulverizer was used and it turned out a 20 mesh dust of which about 75% would pass 200 mesh. Some men question whether the ordinary mining methods made such a dust and so doubted the explosibility of the dust in their own mines. The question was well taken, and hundreds of dust samples were taken by the field men of the Bureau to determine the kind of dust being made in all methods of mining and all classes of coal. The result of such sampling showed some coals. resisted breakage more than others and that actual mine road dust, through 20 mesh, would show from 10 to 20% through 200 mesh, and for actual rib and roof dust through 20 mesh, they would get from 20 to 40% of 200 mesh dust. In testing the

Jan 1, 1924

will be held at COSMOPOLITAN HOTEL DENVER COLORADO June 3,4,5, 1931

Jan 1, 1930

The 1939 meeting will be held in Salt Lake City, the exact date to be announced later. If you have any suggestions for the place or program, send them to the Secretary at once.

Jan 1, 1938

Houston T. Aars Carter Mining Co. Sundance Rt. Moorcroft, WY 82716 Charles R. Ahlbrecht Western States Surveying Inc. 7030 So. Yosernite Englewood, CO 801 12 Dean Albon Monsanto Co. 800 No. Lindberg St. Louis, MO 631 67 Robert Anderson Mobil Oil Producing Inc. POB 17772 Denver, CO 8021 7 Stephen P. Antony Orbital Engineering 6789 So. Yosernite Englewood, CO 801 12 David Ariotti Boyle Mining Engineering Service Rt. 1 Box 15M Helper. UT 84526 Douglas Auck Falkirk Mining Co. 103 McKinley Ave. Underwood, ND 58378 Roger Backrnan N. D. Crockett & Assoc. 3467 Sorenson Way Salt Lake City, UT 84109 Richard Bailey Continental Conveyor & Equip. Co. 602 Park Point Drive Golden, CO 80401 Earl W. Baker Baker & Co. 4965 Jackson St. Denver, CO 80216 Allen P. Barber San Juan Coal Co. 705 Ocio Farrnington, NM 87421 Edward Barker Process Equipment Builders POB 7506 Paducah, KY 42001 Larry Barton Carter Mining Co. 101 5 Teewinot Circle Gillette, WY 82716 Hugh Bastian American Carbide Corp. POB 2650 Ronald N. Batdorf Monsanto Co. Box 701 Saratoga, WY 82331 Georgetown, KY 40321 Doris A. Bauer Mobile Oil Corp. POB 17772 Denver, CO 80217 Jan Beam Blount International Ltd. 2570 So. Dayton Way #E-308 Denver, CO 80231 Mac Beaudry Falkirk Mining Co. 1029 Cannon Ln. Washburn, ND 58527 R. C. Beerbower Gates Engineering Co. Drawer A Beckley, WV 25801

Jan 1, 1982

[Mr. Houston T. Aars Carter Mining Co PO8 3007 Gillette, WY 82716 Mr. Jay Abbott Union Supply Co 7458 S Jackson St Littleton. CO 80122 Mr. Ronald H. Achziger Midwest Rbr & Sply Co 6404 E 39th Ave Denver, CO 80207 Mr. Randy Acre Dorchester Coal Co 9350 E Arapahoe Rd Englewood, CO 80112]

Jan 1, 1983

At the Annual Meeting of the RMCMI Board of Directors held June 29, 1985, the following amendments to the corporation bylaws Article III were made: Section 2. Advisory Board. There shall be an Advisory Board of Directors which shall be com- posed of all former presidents of the corporation and of the unincorporated association, also known as The Rocky Mountain Coal Mining Institute, of which the corporation is the successor. The Advisory Board shall periodically review the philosophy and policies of the corporation and make recommendations concerning the same to the Board of Directors. The Advisory Board shall hold an annual meeting at the same place as and immediately pre- ceding the annual meeting of the members in each year and written notice stating the place, day, and hour of the meeting shall be given or mailed to each member of the Advisory Board at least thirty days prior to the date fixed for such annual meeting. The annual meeting of the Advisory Board shall be for the purpose of electing a chairman from among its members and the person so elected chairman shall also serve as a member of the Board of Directors of the corporation. The Advisory Board shall meet at such other times and conduct its affairs in such a manner as it shall determine from time to time by resolution. Section 4. Regular Meetings. A regular meeting of the Board of Directors shall be held immediately following the annual meeting of the members, at the site of the annual meeting of the members, the day and time to be fixed by the Board of Directors at its annual meeting immediately pre- ceding the annual meeting of the members in each year, without the necessity of any other or advance notice. Such regular meeting of the Board of Directors shall be for the purpose of considering committee appointments, and for the transaction of such other business as may come before the meeting. A regular meeting of the Board of Directors shall also be held in the Fall of each year following the annual meeting of the members and written notice stating the place day and hour of the meeting shall be given or mailed each member of the Board of Directors at least thirty days prior to the date fixed for such regular meeting. Such Fall regular meeting of the Board of Directors shall be for the purpose of receiving the treasurer's annual financial report of the previous fiscal year as reviewed and approved by the auditor, to take action on the budget, and for the transaction of such other business as may come before the meeting. Section 8. Standing Committees. The Board of Directors may create by resolution adopted by a majority of the entire Board of Directors, a Bylaws and Resolutions Committee, a Nominating Committee, a Finance Committee, and one or more other committees each of which shall consist of two or more directors and which shall have and may exercise such authority in the management of the corporation as shall be provided in such resolution or in these bylaws. Section 9. Ad Hoc committees. The Board of Directors from time to time may by resolution create a Membership Committee, a Scholarship Committee, an Education Committee, various convention committees, and one or more other committees each of which shall consist of members of the corporation and which shall have and may exercise such authority, other than in connection with the management of the corporation, as the Board of Directors may determine. MINUTES of the Rocky Mountain Coal Mining Institute 81 st Member Annual Business Meeting July 2, 1985 The 81st Annual Business Meeting of the mem¬bers of The Rocky Mountain Coal Mining Institute was called to order by the president, Charles W. Margolf at 1:35 p.m. Tuesday, July 2, 1985 in the Windom Peak Room of the Tamarron Resort near Durango, Colorado. Thirty members were present and a quorum was established. It was moved by Bill Balaz, seconded and car¬ried to dispense with the reading of the minutes as these were published on pages 67 thru 77 of the 1984 issue of the Proceedings. The chair called for reports of the various com¬mittees and these reports will be placed on file in the RMCMI Office. Bylaws and Resolutions. Chairman Loren V. Linville reported that the Board of Directors had adopted changes to Article III, Sections 2, 4, 8 and 9 calling for clarification of Ad Hoc and Standing Committees as well as setting forth a purpose for the Advisory Board meetings and stating a time for an annual meeting. He further reported that the Board had passed three resolutions: (One) Noting the passing of these members since the last conven¬tion - Einar M. Arentzen, Gerhardt A. Benne¬witz, Claude P. Heiner, Raymond A. Johnson, Vard H. Johnson, P. T. Schonstrom, Augusta F. Whiteside and Edward Wiemann; (Two) Of appreciation to the officers, chairmen and their commit-

Jan 1, 1985

Allis Mineral Systems ARCO Coal Company Buckley Powder Co. CALCO, Inc. Coal Magazine Colowyo Coal Company Continental Conveyor & Equipment Company Crane & Hoist Sales Cummins Southwest, Inc. Energy West Mining Company Paul J. Epley FMC Corporation The Falkirk Mining Company Fleischli Oil Co., Inc. T. J. Gundlach Machine Company Halbach & Braun Harnischfeger Corporation Hemscheidt Corporation Hyatt Regency Beaver Creek Jennmar Corporation Joy Technologies, Inc. K&P Sales Engineers, Inc. Kennametal, Inc. Kerr-McGee Coal Corporation McLanahan Corporation National Coal Association The North American Coal Corporation Northwestern Resources Company Peabody Coal Company Phillips Machine Service, Inc. Pincock, Allen & Holt, Inc. Pittsburg & Midway Coal Mining Co. Roberts & Schaefer Company Rust Tractor Company Salt River Project Santa Fe Pacific Coal Corporation Schroeder Industries Shearson-Lehman Brothers Southern Pacific Transportation Stamler Corporation Trapper Mining Inc. Wagner Equipment Company Western Energy Company Wheeler Machinery Company

Jan 1, 1992

Amercable, Inc. Andalex Resources, Inc. ARCO Coal Company Behre Dolbear & Company, Inc. Colowyo Coal Co. L.P. Continental Conveyor & Equipment Company Crane & Hoist Sales Crested Butte Mountain Resort Cyprus Amax Coal Co. Energy West Mining Company The Falkirk Mining Company Fleischli Oil Co. Inc. Halbach & Braun Industries Hemscheidt Corporation GH Henley Industries Ingersoll-Rand Co. Jennmar Corporation Joy Technologies, Inc. K & P Sales Engineers, Inc. Kennametal, Inc. Kerr-McGee Coal Corporation L & H Welding & Machine Co. McLanahan Corporation National Coal Association The North American Coal Corporation Northwestern Resources Company Peabody Western Coal Company Phillips Machine Service Pincock Allen & Holt Ramsey Technology, Inc. Rust Tractor Company Salt River Project Schroeder Industries Stamler Corporation TerraMatrix TIC (The Industrial Company Wyoming, Inc.) Trapper Mining Inc. Wagner Equipment Company Western Energy Company Wheeler Machinery Company

Jan 1, 1994

[ ]

Jan 1, 1996

[Mr. Scott Aberle Western Energy Co POB 99 Colstrip, MT 59323-0099 Mr. Brian L. Acton Oxbow Carbon & Minerals Inc 1601 Forum Pl-#P2 West Palm Beach, FL 33401 Mr. Laine W. Adair Genwal Resources Inc POB 1420 Huntington, UT 84518-1420 Mr. Thomas D. Aderman The North American Coal Corp 14758 Preston Rd #1100 Dallas, TX 75240-7891]

Jan 1, 1998

[Participating Scholarship Colleges and Universities 154 ACZ 149 AmerCable,Inc 144 Andalex Resources, Inc 118 Behre Dolbear & Company, Inc 101 Canyon Fuel Company 145 Commercial Testing & Engineering Company 95 Continental Conveyor 148 Cove Shoes 136-137 Crane & Hoist Sales Inc 121 Crested Butte Mountain Resort 134 Cyprus Amax Minerals Company 115 Dakota Coal Company DriltechInc 135 Empire Machinery Company 94 Energy West Mining Company 122 Fluor Daniel 100 GH Hensley Industries 126. 127 Hitachi Construction Machinery (America) Corp 123 Holme, Roberts & Owen 98 Honnen Equipment Company 150 Ingersoll-Rand Company 141 Jennmar Corporation 142 Joy Mining Machinery - A Harnischfeger Industries Company 104 K & P Sales Engineers, Inc 114 Kennecott Energy Company 155 Kerr-McGee Coal Corporation 96 LeTourneau,Inc 160 Long-Airdox Company 112 Magnum Metals, Inc 133 McLanahan Corporation 129 Mine Technik America 124 Mineral Tech 151 Morrison Knudsen Corporation 97 The North American Coal Corporation 130 Northwestern Resources Company 125 P&H MinePro Services 157 Peabody Western Coal Co 131 Phillips Machine Service, Inc Pincock Allen & Holt 120 Powder River Coal Company 107 Pyro-Chem 156 RamseyTechnology, Inc 119 Rust Tractor Company 90 Salt River Project 91 Savage Industries Inc 89 Schroeder Industries 147 Sheraton Steamboat Resort and Conference Center 111 Skelly & Loy 138 Snowmass Village at Aspen 146 Stamler Corporation (An Oldenburg Group Company) 117 Tamarron Hilton Resort 140 TerraMatrix Inc 139 TIC (The Industrial Company of Wyoming, Inc.) 99 Trapper Mining Inc 106 Wagner Equipment Company 116 Weir International Mining Consultants 113 Westech 152 Wheeler Machinery Company 128]

Jan 1, 1997

The sixth Annual RMCMI Mine Rescue Evaluation was held during the 1997 Institute convention at Sheraton Steamboat Resort, Colorado. The Mine Rescue committee, co-chaired by Becki Boam and Gary Cook, is one of 18 committees of the Institute. In 1997 the largest number of teams participated in the program. There were nine: BHP Minerals - La Plata Mine, BHP Minerals - Navajo Coal Co., BHP Minerals - San Juan Coal Co., Bridger Coal Co., The Coteau Properties Co., General Chemical Co., The Sabine Mining Co., Solvay Minerals and Western Energy Co. Professional evaluators who provided challenging scenarios for the 80 participants were Jack Knight of Milton, Florida; Wilson Begay, Chris Saxon, and Gaylon Yazzie all of Western States Security; Mary Bailey, Bailey Associates; Tom Bass, California Department of Corrections; and Art Saenz, BDC. Seven members made up each team plus one or more trainers and represented the states of Montana, New Mexico, North Dakota, Texas and Wyoming. Ten different scenarios were presented during the two day evaluation. Each team was given the pertinent information to solve the problem as they assembled at the site. Mine Rescue families and friends participated as victims providing realistic scenarios to simulate the stress of an actual rescue incident. Each team was unaware of the circumstances until arriving at the various scenes in and around the Sheraton resort. [ ] These teams are providers of prompt rescue and medical care for accident victims at their respective properties. The members act with immediate and professional knowledge to save lives and prevent further injuries. Sponsors who contributed financially to the 1997 program are: Argo Industrial, Antelope Construction, Fisher Safety Supply, Flanders Electric Motor Service, Inc; Intermountain Electronics, Inc.; King Energy Services, Inc.; Rocky Mountain Electric Motors, LS.; TerraMatrix and Triune Inc. On Saturday evening, June 28, a reception was held for all mine rescue participants and spouses who had advance registered for this social event. The RMCMI Board of Directors was invited to attend and meet with the teams. As convention attendees, all mine rescue participants and registered families attended the Monday night country western reception and Bar-B-Q. This was followed by an adult western melodrama. [ ] Glass awards with the RMCMI logo and a Mine Rescue figure were presented at the Tuesday Mine Rescue buffet breakfast to all nine teams, each of which had achieved proficiency at level 3. Captains of the teams pictured below are (from left standing): Ron Neff, BHP-San Juan; Ted Laughline, Bridger, Terry Davis, Coteau; Jim Knutson, General Chemical (from left kneeling): Dan Allerdings, Rosebud; Ron Miller, BHP-Navajo; Jonathan Sorrell, BHP-La Plata and Ray Blaisdell, Solvay. Gary Cook is to be commended for his solo last minute supervision of the Mine Rescue program, due to Becki Beam's unavoidable absence. The teams look forward to the 1998 convention at Snowmass Village Resort, Colorado Thursday and Friday, June 25 and 26.

Jan 1, 1997

[Participating Scholarship Colleges and Universities 138 AmerCable 130 Andalex Resources, Inc 82 Behre Dolbear & Company, Inc 83 Commercial Testing & Engineering Company 86 Continental Conveyor & Equipment Co 87 Crane & Hoist Sales Inc 12 Crested Butte Mountain Resort 88 Dakota Coal Company 89 Empire Machinery Company 90 Energy West Mining Company 91 GH Hensley Industries 92, 93 Hitachi Construction Machinery (America) Corp 96 Ingersoll-Rand Company 131]

Jan 1, 1998

[Scott Aberle Western Energy Co POB 99 Colstrip, MT 59323-0099 Randy Acre Joy Mining Machinery 2569 Silver Oak Ct. Grand Junction, CO 81505 Brian L. Acton Oxbow Carbon & Minerals Inc 1601 Forum P1-#P2 West Palm Beach, FL 33401 Laine W. Adair Genwal Resources Inc POB 1420 Huntington, UT 84528-1420 Kent Adamson Solvay Minerals POB 1167 Green River, WY 82935]

Jan 1, 1999

The eighth annual RMCMI Mine Rescue Evaluation was held during the 1999 Institute convention at the Crested Butte Marriott Resort, Colorado. [ ] Elliott Tsosie, Mary Rowell, Janna Aune, Guy Horton, Art Saenz and Bill Balaz were pleased with the 1999 Mine Rescue Program, The Mine Rescue committee is but one of 17 volunteer committees; this one co-chaired by Bill Balaz, Elliott Tsosie and Janna Aune. There were three evaluators, Art Saenz, Western Environmental; Mary Rowell, ProCare and Guy Horton, Horton Rope Rescue. Nine teams participated and brought 89 participants, 26 spouses, nine children and five teens. The teams were BHP LaPlata, BHP Navajo, BHP San Juan, all from Farmington, NM; Bridger Coal Co., Rock Springs, WY; The Coteau Properties Co., Beulah, ND; Northwestern Resources, Jewett, TX; Powder River Coal Co., Gillette, WY; Solvay Minerals, Green River, WY and Western Energy Co., Colstrip, MT. To observe were members from Centralia Mining Co., Centralia, WA. [ ] Evaluators: Mary Rowell, Guy Horton &Art Saenz The three professional evaluators provided challenging scenarios for the Mine Rescue participants on the grounds of the resort property. Some attending convention were alarmed to see stretchers with "victims" and phoned the hotel switchboard to report the catastrophe. Team members had no prior knowledge of what the scenarios might be and derails were provided only as they arrived at the scenario location, with one exception. Seven to ten or more articipants make up each team. Some teams also ring an alternate and team trainer. For identification purposes, the "victims" wore white shirts emblazoned both front and back with a red VICTIM designation. There was a staged demonstration by three response teams who had not previously worked together. This was enacted on the convention floor following a Technical Session meeting attended by about 200 members. Three response teams from BHP's Navajo and San Juan Mines together with Coteau Properties' Freedom Mine provided a demonstration of their response skills. For never having worked together before, they presented a very professional enactment. This is described at length in the Welcome Session copy. Training sessions were held Saturday and Sunday to enable the teams to prepare for the scenarios. A swap meet was Saturday evening for teams to swap hats, shirts, belt buckles, stickers etc. Each participant received a royal blue golf shirt and ivory cap with royal blue bill. Culmination of the Mine Rescue program was a Tuesday morning Awards breakfast when teams were presented with jade acrylic plaques. [ ] Teams participating in the Mine Rescue Evaluation received trophies on Tuesday morning. The captains above represent BHP-La Plata, BHP-Navajo, BHP¬San Juan, Bridger Coal Co., The Coteau Properties Co., Powder River Coal Co., Solvay Minerals, and Western Energy Co. Sponsors who contributed financially to the 1999 Mine Rescue program were Balaz & Associates, CMC, Civil Constructors, Colstrip Electric, Farmington Fire Equipment & Safety, Fisher Safety, Flanders Ellctric Motor Service, Magnum Metals, Richard Palmtag, Rocky Mountain Electric Motors, Sedona Consulting and Western Water Consultants. [ ] Evaluator Art Saenz likes to have the upper hand and will take whatever steps necessary to get it.

Jan 1, 1999