Search Documents

By R. F. Stewart

A sedimentation method involving the use of the Palo-Travis apparatus was found satisfactory for rapid determination of the size distribution of coal particles ranging from 10 microns in diameter to those passing an 840-micron opening (20-mesh sieve), The method is most useful for comparing the size distributions of samples of pulverized coal where the actual size of the particles is not required and is applicable to sieve and subsieve sizes of a wide variety of coals and chars that can be wetted and are heavier than water. An analysis, including all calculations, can be completed in 1/2 to 10 hours, depending on the time required for the finely divided coal to settle. A typical analysis requires about an hour, making this a rapid, precise method for routine size-distribution analysis of powdered coals. When used with coal particles smaller than 400 microns, the method is precise within 15 microns for wide variations in test conditions and within 5 microns for identical test conditions. The precision decreases as particle size increases, becoming unsatisfactory for particles larger than 400 microns (40-mesh). For precision within 15 microns, the samples must be equal in weight. Greater precision is obtained with 4-gram samples, but samples as small as l gram may be used.

Jan 1, 1961

By Michael G. Zabetakis, Israel Liebman, Henry E. Perlee

Flammability studies conducted to date on stratified methane - air and pentane - air mixtures in air indicate that location and extent of a flammable layer are affected by molecular diffusion , gas motion , and propagation of flame . In initially quiescent mixtures , the lower limit - of - flammability zone may be determined by assuming molecular diffusion alone governs mixing rate . The upper limit - of - flammability zone can be predicted in this manner only for stratified layers with small concentration gradients ( less than 0.2 volumepercent per inch ) ; where large concentration gradients are encountered ( for example , as much as 30 volume - percent per inch ) , the initial - mixture methane concentrations that yield flammable mixtures are larger than anticipated . Flames propagating through heterogeneous quiescent methane - air atmospheres in the direction of the concentration gradient exhibit flame speeds at any point that corresponds to the flame speed of the homogeneous gas mixture having the same gas composition as that of the point in the heterogeneous system . In flowing mixtures with large concentration gradients , the degree of mixing prior to ignition does not appear to affect the flame velocity and emitted radiation appreciably in a 6.5 - ft - diameter gallery .

Jan 1, 1964

By R. V. Ramani

In this report, the application of the Open Pit Materials Handling Simulator (OPMHS) to a mine located in Illinois using bucket wheel excavator (BWE) and a stripping shovel in tandem for overburden removal is described. The specific objective of the study is to demonstrate the application of the simulator to analyze mine planning and scheduling problems and to generate and analyze alternatives for increased production. On the basis of the simulations it was concluded that the maximum productive capacity of the system in raw coal was around 3000 tons per shift. At this production level, the equipment combination and availability also satisfy the match requirements for the stripping shovel and the BWE, and the overburden and coal removal systems. Several alternatives requiring new equipment are proposed and analyzed for increasing production. However, no economic analyses of these proposals were done.

Jan 1, 1977

By Paul W. Jeran

Subsidence was monitored by the U.S. Bureau of Mines over the ends of longwall panels operating in the Pittsburgh, Kittanning, and No. 2 Gas Coalbeds of the northern Appalachian Coal Basin. The final subsidence over the finishing ends of three panels in the Pittsburgh Coalbed are compared with the subsidence measured over the rib at these panels. The characteristics of subsidence are different. At Mine A, data over the start of a longwall panel shows similar characteristics to the subsidence measured over the rib. Subsidence over the fmishing ends of panels in the Kittanning and No.2 Gas Coalbeds are also different from the subsidence over the rib. The use of a subsidence prediction model based on data gathered over the rib of a panel will not yield accurate results if it is applied to the finishing end of a longwall panel. Acceptable results may be obtained along the centerline over the starting end of a panel.

Jan 1, 1991

By Robert S. Sanford

The Broughton and Ring magnetite deposits in Essex County, N. Y., are thought to be in a mineralized belt that extends from the Lake Sanford mining district to Lake Champlain and passes through the Mineville district. The country rook is syenite-gneiss, similar to that in the Mineville area. The Bureau of Mines conducted a vertical magnetometer survey of the area. On the Broughton properties there are no indications, magnetically, of magnetite in any degree of concentration. 'On the ding properties a number of sharp, localized magnetic anomalies were observed. One core-drill hole was bored to a, depth of 48.3 feet, also, to test one of the strongest anomalies. The field work was in progress from December 1943 to July 1944. Although no iron ore was intersected by' the drill hole, it showed that the amphibolite rook, at a depth of 6 to 100 feet below the surface, contained enough magnetite and iron sulfides to account for the anomalies recorded by the magnetometer survey.

Jan 1, 1949

By Richard F. Hewlett

Use of digital computers makes possible a more efficient and complete analysis of data from a mineral deposit . This computer program was written and used during an investigation into the efficiency of methods of computing grade and tonnage of ore , wherein it was necessary to make repeated computations involving different combinations of data . This investigation was part of a continuing program of sampling methods research at the Bureau's Denver Mining Research Center.2-4 This program is designed to compute tonnage and average grade for 40 cutoff grades using either the statistical or polygonal methods . tational rate is from 200 ( input bound ) to 1,400 assays per minute , depending on the use of either individual ( one assay per card ) assay- interval length or

Jan 1, 1963

By Joseph E. Matta, John C. LaScola, Fred N. Kissell

The Bureau of Mines investigated coal storage silos to determine how gassy coal must be for methane accumulations in a silo to become hazardous and where such accumulations are likely to occur. Methane concentrations were measured in the open space above the stored coal pile, in the pile, and in the reclaiming area. No methane layering was found in closed-top silos. Reclaiming areas were as gassy as the top part of the silos. Coal samples were collected from the conveyors entering the silos in order to assess the gassiness of the coal. No simple correlation was found between the gassiness of the coal stored and the measured methane concentrations. However, at mines where the average 24-hour gas emission from the conveyor belt samples was 14 ft3/ton or more, fans or open tops were used. It appears that a large fraction of the methane released during storage remains in the void space between the coal particles.

Jan 1, 1981

To provide a method for locating trapped miners promptly and accurately. The Approach: Develop a wireless emergency system that is intrinsically safe, compact, easy to operate, reliable, sturdy, and economical. How It Works: A (one transmitter has been developed under Bureau of Mines contracts. The transmitter weighs only a few ounces, is powered by a cap lamp battery, arid can be carried on the miner's belt. A compact loop antenna, which could either be carried by the miner or strategically located in the mine, is used to generate a magnetic field that is sensed by a mobile receiver on the surface. When needed, the antenna is deployed to form a single loop. In mines where the overburden is less than 600 feet, a loop of No. 19 wire approximately 30 feet in circumference is normally adequate. This antenna weighs less than one half pound. In deeper mines, a heavier wire and bigger loop is required; a No. 10 wire deployed around a pillar has been used.

Jan 1, 1974

By R. M. Santmyers

This paper represents one of a series of digests of foreign mining legislation that is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the mining legislation of Tunisia was prepared from a copy ( in French ) of the Mining Decree of Tunisia promulgated December 29 , 1913 , by the Resident General of France in Tunisia and effective January 1 , 1914. It is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers , to whom it will be referred through the courtesy of the Department of State .

Mar 1, 1933

By George H. Holmes

This paper , which describes mining methods and milling and manufacturing operations at the gypsum property of the Blue Diamond Corp. , is one of a series on mining methods and practices being prepared by the Mining Division of the Bureau of Mines . The property comprises about 4,000 acres and is in secs . 30 , 31 , 32 , and 33 , T. 21 S. , R. 59 E. , and secs . 5 , 6, 7 , 8 , and 9 , T. 22 S. , R. 59 E. , M. D. B. and M. , Clark County , Nev . , approximately 23 miles by paved highway southwest of Las Vegas , Nev . ( fig . 1 ) . This circular summarizes the history of company operations , describes physical features , labor and living conditions , and the geology . The method of exploration is outlined , and the section on mining methods contains descriptions of open - pit and underground systems , including loading and transportation methods . The crushing plant and tramway are described , as well as plaster-mill and board -plant practices . The boiler plant and organization are described , and wage scales are contained in the concluding section of the circular .

Mar 1, 1950

By J. M. Mutmansky

"This study analyzed laboratory comminution techniques for respirable mine dust generation and the properties of the resulting dusts. It was the objective of the study to determine the suitability of the resulting dusts in reflecting the properties of natural airborne dust. This paper deals specifically with the amount of contamination introduced into the generated dust as a result of abrasion when using nine different grinding methods. The analysis was made by comparing the content of 25 chemical elements in the lab-generated dusts with the same elements in the airborne coal mine dusts. It was found that all the lab-generated dusts possessed contamination but that several methods produced smaller percentages of contamination and that the residence time in the grinding device was an important factor in the contamination levels. INTRODUCTIONDust in the atmosphere is a health hazard and a major source of occupational diseases in the coal mining industry (Anon., 1980; Merchant, Boehlecke, and Picket-Hamer, 1986). It has been shown that coal workers' pneumoconiosis (CWP) is directly related to the inhalation and accumulation of respirable coal dust in coal miners' lungs. In order to effectively protect coal workers from coal dusts, we must have a clear understanding of dust properties including dust generation and dust-lung reaction mechanisms. This requires extensive biomedical research. Dust related research often requires large samples of respirable coal dusts to be collected, either for repeated experiments or stored for future reference. Unfortunately, current sampling instruments are not able to meet this demand. Ali a result, laboratory-generated coal dust ls frequently used as a substitute for coal mine dust in biomedical and other research applications. Now, the questions are how close the characteristics of laboratory-generated dusts are to those of mining-generated dusts and which equipment is moat appropriate for research dust production in the laboratory . These are some of the interests of this research project. The primary objective of this project was to find a laboratory technique which can generate coal dusts possessing properties similar to coal mine dust with respect to particle size distribution, chemical composition, and particle shape and morphology. However, this paper will focus only on the chemical compositions of the prepared dust samples and try to identify the sources of chemical contamination from various size reduction processes."

Mar 1, 1992

The Bureau of Mines equipped a longwall shearer with a water-jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 190 psi, and with water-jet-assisted cutting pressures ranging from 1,000 to 6,000 psi. At water pressures of 3,000 psi and higher, dust concentrations were reduced by as much as 85 pct via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1986

By Paul M. Tyler

The alkali metals , sodium and potassium , and more particularly sodium , occur abundantly in chemical combination with other elements . The elements themselves are available in metallic form but are so active chemically that they oxidize rapidly in contact merely with the air . Potassium will even catch fire spontaneously in air , and both the metals will decompose water with explosive violence . Inasmuch as they are almost as soft as wax they are not suitable for the structural or other mechanical uses characteristic of ordinary metals , and consequently the uses of these elements even in the metallic condition are based upon chemical rather than physical qualities . Sodium metal is used largely as a commercial reducing agent , but potassium metal is rarely found outside of chemical laboratories . Numerous salts and other compounds of these elements enter largely into world trade and are commercially very important , but none of these compounds except sodium peroxide and sodium cyanide are made economically from the metals . Sodium is generally considered as rather an uncommon metal , but in point of annual tonnage produced it is far more important than mercury , magnesium , molybdenum , bismuth, cadmium, cobalt , gold , silver , or the various rarer metals .

Apr 1, 1932

[ ]

Jan 1, 2011

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

1, Introduction This report is submitted in fulfillment of the requirements of USBM Contract No. J0255017, "Development of Emergency Escape Systems Guidelines for Underground Metal and Nonmetal Mines" Under this contract the history of past mine fires was studied. Representative metal and nonmetal mines were surveyed and escapeways, refuge chambers, life support, and emergency hoist requirements were studied to determine the problems in complying with the proposed regulatory standards and their enforcement by MESA Mine Inspectors. In addition, a computer program was written to evaluate mine evacuation performance. The completed program is included in the appendix. 1. 1 Historical Review of Metal and Nonmetal Mine Fires Early records of mine fires are poorly documented because there was no statutory provision for reporting fires to the Bureau of Mines. The survey of representative mines during the course of this contract indicated that many small fires still go unreported even though they are now required to report all fires A recent report survey approximately 80 disasters in metal and nonmetal mines, (6 ) Table I is a summary of some of these fires. Historically most metal and nonmetal mine fires have been caused by electrical problems. Spontaneous combustion and the use of welding equipment are the other major causes of mine fires(14) Although not documented, many mine personnel agree that 30 percent to 40 percent of underground metal and nonmetal mine fires have their origin from cigarettes and other smoking related materials. The number of fires related to spontaneous combustion is decreasing and equipment fires are on the increase. The reduction of spontaneous combustion fires can be attributed to the use of sandfill in more mines and the increase in equipment fires to the increased use of LHD equipment.

Jan 1, 1976

By Bill M. Stewart

To decrease the potential for fine coal waste slurry impoundment failures, the Bureau of Mines investigated a new disposal technique. The fine coal waste slurry is rapidly thickened (i.e., dewatered) and deposited on a slightly sloping surface. To accomplish rapid dewatering, a chemical flocculation system using polymers was developed to treat the fine coal waste slurry stream. The fine solids formed flocs, settled from suspension, and rapidly released excess water. During the last 5 days of the field test, slurry flowing at rates from 498 to 675 gal/min with a specific gravity range of 1.15 to 1.33 was successfully treated and dewatered. During this period, untreated slurry had an average moisture content of 227.4 pct (30.7 wt pct solids). The effectiveness of the dewatering system was determined by monitoring the moisture content of the deposited waste with respect to time. Sixty-five hours after ending the field test the average moisture content was 54.9 pct (64.5 wt pct solids); 68 days after the field test the average moisture content was 28.8 pct (78.0 wt pct solids).

Jan 1, 1986

By J. C. Holtz

Since 1937 the Bureau of Mines has conducted investigations to provide the technical information necessary to guide the safe use of diesel engines underground in the United States. Coincident with the beginning of the technical study, a survey was made of State regulations pertaining to the use of internal-combustion engines underground.3/ At that time it was found that owing to the known hazards of gasoline locomotives, many States had enacted legislation or regulations limiting or prohibiting their use underground. Some of this legislation prohibited, or could be interpreted as prohibiting, the use of any type of internal-combustion engines in underground workings. After World War II diesel-powered equipment was introduced underground in many States, and pertinent questions are received frequently by the Bureau of Mines about the regulations that permit such applications. Because it was known that new and revised regulations had been made effective in some States in the nearly 20 years that have elapsed since the previous survey,3/ the Bureau decided that a review of the latest regulations in the leading mineral-producing States would be a valuable source of information for those engaged in the production of minerals as well as others. Accordingly, where feasible, this report includes abstracts of State laws and regulations as they affect the use of internal-combustion engines underground, particularly diesel engines. The substance of comments from State officials also are included when these appear to be helpful to interpretation of the regulations.

Jan 1, 1957

By Mary F. Koehler

Interoxidic compounds, such as vanadates, have not been studied extensively in the field of thermodynamics. This is a report of three vanadates of sodium--metavanadate, pyrovanadate, and orthovanadate. Vanadates of other metals will be considered in future reports. The heats of formation at 298.15° K. of the three sodium vanadates (both from the oxides and from the elements) were derived from the results of sodium hydroxide solution calorimetry. Free energies of formation were obtained by combining heat and entropy values. The results support the conclusion that the three sodium vanadates were stable with respect to all possible decompositions in which vanadium retains its pentavalency.

Jan 1, 1960

By Philip C. Good

The Bureau of Mines investigated the feasibility of utilizing low-grade phosphatic shale as a feed for phosphoric acid production. Present practice in the phosphate mining operations of southeastern Idaho is to remove and either stockpile or waste low-grade phosphatic shales as the high-grade phosphate beds are selectively mined. Acid digestion studies were performed on uncalcined shale and on shale calcined to remove free carbon to determine phosphoric acid quality, yield, and amenability to filtration. The untreated shale, containing 21.4 pct P205, was digested with sulfuric acid in a single-tank reactor to yield phosporic acid and gypsum residue. Although 96 pct P205 recovery was attained in digesting uncalcined shale, only the calcined product gave satisfactory filtration rates. Calcined shale yielded phosphoric acid recovery of about 93 pct of the contained P205. It was higher in impurities than commercially prepared acid derived from high-grade western phosphate rock. An acid filtration rate of 745 lb P205/ft2/day was attained. This value is lower than the rate of 900 lb P205/ft that is generally considered to be acceptable in industrial production of phosphoric acid from high-grade phosphate rock.

Jan 1, 1981

By C. P. Fang, V. A. Marple, K. L. Rubow

"Studies of the flow fields and particle impaction characteristics are more complicated in multi-nozzle impactors than in single-nozzle impactors, since the jets of air must penetrate cross-flowing air to impinge on the impaction plate. Results of heat and mass transfer analysis are employed to describe the cross-flow pattern in multi-nozzle impactors. A cross-flow parameter has been derived to predict the deflection of the air jet by the cross-flow. This parameter is expressed as a function of the geometric parameters for the multi-nozzle impactor. DnN 4D,, where N is the number of nozzles, Dn the nozzle diameter and D, the nozzle cluster diameter. Empirical particle collection data show that multi-nozzle impactors operate satisfactorily, if the cross-flow parameter is less than a critical value of 1.2. Impactors operating with a cross-flow parameter larger than this critical value are shown to possess poor particle collection characteristics.Inertial impactors of many designs have been used for sampling aerosol particles. Impactors can be single stage, consisting of a nozzle and an impaction plate, or a cascade impactor with several stages in series. The simplest design for a stage is a single nozzle with a flat impaction plate. However, many designs use stages with multiple nozzles of identical size, which allows for compact impactors to be designed at rather substantial flow rates and moderate pressure drops.Nearly all of the theoretical work, and much of the experimental work, has been performed on single-nozzle impactors. The results of single-nozzle impactor analysis are often applied to multiple-nozzle impactors, which are assumed to be a group of individual nozzles, each operating as though they were single nozzles. However, an important fact is often ignored: the interaction of flow from adjacent nozzles can change not only the fluid mechanics in the impaction region, but also the locations of the jet stagnation points, and the impaction characteristics of each nozzle.The effect of multiple nozzles on the particle collection characteristics of impactors has been studied by a few investigators. May (1964), Fletch et al. (1967), Friedrichs (1968), and Vaughan (1986) reported that the quantity of particles in deposits of nozzles in the first two stages of the Andersen multi-nozzle cascade impactor were not equal. The inner deposits appeared to contain fewer particles than the outer ones. However, Vaughan (1986) in addition showed that many of the deposits in the outer three rows were missing on the first stage, even though the outer deposits that were present were larger than the inner deposits.May (1964) conducted experiments and explained the phenomenon of smaller deposits near the center than near the edge. He noted that in Andersen cascade impactors the air issuing from the nozzles moves radially outward along the narrow channel between the nozzle plate and the impaction plate. This flow at 28.31min -1 created a pressure difference of about 1 mm water between the inner and outer sections of the channel. The effect was most pronounced in the first two stages, where the pressure drop across the nozzles was also about 1 mm water. Here, the flow velocities in the nozzles, and hence the deposits, were smallest at the center and increased toward the periphery of the impaction plate. since the pressure drop across the nozzles was the smallest at the center and a maximum at the periphery. This effect was negligible in the lower stages because of a larger pressure drop across the nozzles. According to May (1964), this effect could be eliminated by increasing the nozzle-to-impaction-plate distance to three nozzle diameters and improving the nozzle arrangement to allow air flow to escape to the periphery more easily."

Mar 1, 1992