Search Documents

By F. E. Griffith, C. H. SEELING

Cardox blasting is used widely in coal mines in the United States . A model of a Cardox blasting device was approved by the Bureau of Mines subject to certain conditions and limitations , and the approval was extended to other models from time to time . Certain special hazards are entailed in the use of Cardox as with explosives . One of these is flying shells . In some blasts , the Cardox shell is violently ejected from the borehole and flies like a projectile , frequently ricocheting off solid objects and striking points considerably off the line of its initial flight . Flying shells have been known to pierce the webs of structural - steel beams , to pass through both sides of allsteel mine cars , to be driven through stout hardwood timbers , to knock out timber sets , to damage loading equipment , and to break or short - circuit power lines . A considerable number of shot - firers and other workers have been struck by flying shells and killed or injured . Accidents from this cause , although not as frequent as other types of mine accidents , are usually serious , closely approximating accidents caused by blasting with ordinary explosives . The increasing number of such accidents prompted a Bureau of Mines field investigation of possible methods of preventing dangerously violent ejections of Cardox devices . This report contains pertinent data collected during the investigation and describes methods tested and discarded as well as the development and proof of an apparently satisfactory method .

Jun 1, 1943

By L. J. Douglas, A. G. Kim

Methane and other hydrocarbon gases, byproducts of coalification, are emitted from coal at widely varying rates and often present ventilation problems during mining. The air in some coal mines apparently contains no methane. To determine if coals from mines which had no history of detectable gas emission contained adsorbed methane, samples of coal at the shaft bottom and at an active face were obtained and placed in sealed metal cylinders. The atmosphere around the coal was sampled and analysed by gas chromatography. Methane, ethane, ethylene, propane, propylene, and butane were found to have been desorbed from these coals. Hydrogen and helium were also detected. An estimate of the amount of residual gas per ton of coal indicated that coal samples from the active face generally contained more adsorbed gas than coal samples obtained from the shaft bottom, although in both instances the total amount of gas was relatively small.

Jan 1, 1973

By James W. Vogh

The report covers initial findings in an experimental program to identify diesel exhaust odorants and determine their contributions to diesel odor. The approach was to isolate selected component groups from exhaust and to evaluate the contribution of each group to exhaust odor. Results were obtained for those carbonyls and phenols that could be isolated from exhaust through inter-mediate conversion to oxime derivatives. Unsaturated aliphatic aldehydes and sterically hindered carbonyls were not included. Hydrocarbons intermediate in the diesel range were "also evaluated and an odor contribution was found from those of the aromatic group. The evaluated carbonyls, phenols, and hydrocarbons were found to account for about 20 pct of the total odor in exhaust from an indirect-injection engine during idle. For exhaust from the indirect-injection engine operating under load and from a direct-injection engine at no load, these compounds were found to have no significant levels of odor.

Jan 1, 1972

By M. D. Schlesinger

Experimental data for coal hydrogenation are presented to show that when a vehicle oil produced from coal is present, coal is hydrogenated to the same high conversion whether molybdenum catalyst is impregnated on the coal or intimately mixed with the slurry. Differences in product distribution could be related to the severity of operating conditions. No minimum mixing time was established, but 2 hours was sufficient. Longer periods of mixing, to 14.75 hours, had no effect on the results. The hydrogenation conditions were in the pressure range of 8,500 to 10,000 p,s,i. at 400° to 500° C. Most of the experiments were made in duplicate. The results were obtained with molybdenum concentrations of 0.01, 0.1, and 1 percent. Al the mentioned pressure range and a time at temperature of 15 to 60 minutes, coal conversions higher than 98 percent were obtained.

Jan 1, 1962

By E. C. Perkins

This report describes a ferric chloride trap, based on formation of a low-melting sodium chloride-ferric chloride mixture of near-eutectic composition, and its use in chlorination of impure titaniferous materials. The trap is placed in the hot gas stream between the chlorination reactor and the condenser. Virtually all of the iron is removed by the trap. The condensed titanium tetrachloride is free of suspended solids and contains only a trace of iron. Four examples are given of the use of the ferric chloride trap in chlorination of impure titaniferous materials. INTRODUCTION In the Kroll process, ductile titanium metal is produced by reducing titanium tetrachloride with magnesium metal.4/ In commercial practice, titanium tetrachloride is produced by chlorinating titaniferous materials in the presence of carbon.2/ In 1957 most producers were using rutile, and virtually all plants were designed for its use. About four-fifths of the domestic consumption of rutile was imported from Australia. The Bureau of Mines, under provisions of contract DMP-116 with the General Services Administration, studied electrosmelting of domestic ilmenites and titaniferous magnetites to produce high-titanium slags with pig iron as a byproduct. Under the same contract, chlorination studies also were being made of these slags. Smelting was done at the Northwest Electrodevelopment Experiment Station, Albany, Oreg., and chlorination at the Electrometallurgical Experiment Station, Boulder City, Nev.

Jan 1, 1958

A spectrographic procedure applicable to the semiquantitative determination of 29 elements in tungsten is presented. The method is designed to give estimates of impurity concentrations up to 500 p.p.m. Limits of detectability range from 0.3 p.p.m. for the more sensitive elements to 100 p.p.m. for the less sensitive ones. Tungsten metal samples varying in particle size from minus 300-to 30-mesh are excited in the presence of 5 percent germanium with a direct current arc. Germanium acts to stabilize the arc, minimizes the volatilization of tungsten, and serves as an efficient carrier to sweep impurities from the tungsten into the excitation zone. Curves are presented that show the volatilization behavior of germanium, tungsten, and impurities in tungsten at different concentration levels. Data obtained were used as guides in establishing the method of analysis. In the absence of established reliable analytical procedures for determining many impurities in tungsten in the parts per million concentration range, the spectrographic method described here should prove to be helpful in evaluating high-purity tungsten.

Jan 1, 1961

As part of the Bureau of Mines subactivity in secondary resource recovery and to expand the Nation's mineral base, the Tuscaloosa Research Center made characterization and preliminary beneficiation studies of the waste residues from various coal-conversion processes: from pilot plant tests of the Synthane process for coal gasification, the Synthoil process for coal liquefaction, and the solvent-refined coal (SRC) process for sulfur removal from coal. Those coal conversion processes selected for this study were based on the availability of pilot plant samples. Physical, chemical, and mineralogical examinations of the wastes made to determine the mineral content prior to physical beneficiation tests indicated that in addition to significant quantities of carbon, some trace elements offer potential for concentration.

Jan 1, 1980

By R. V. Ramani, S. Shankar

"The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies.A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec.Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg!m3 (standard deviation= 0.03 mg/m3)from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0.10 mg/m3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. Jr was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed.Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining."

Dec 1, 1996

By J. B. Gayle

The removal of coal particles from a slurry by flotation is made possible by the formation of stable aggregates with air bubbles of suitable sizes. The formation of such aggregates is theoretically possible only for certain favorable combinations of the solid-liquid-gas interfacial tensions. Because interfacial tensions involving solid phases are not conveniently measurable, a related variable, the contact angle, frequently is used as a measure of the floatability of various materials. Zero angles indicate nonfloatable substances, and large angles indicate substances having a high degree of floatability. During a study of contact angles for coal and substances related to coal in their similarity of response to various physical and chemical treatments, particularly flotation, carbonization, and oxidation, the reproducibility of replicate determinations taken within a 4-hour period was found to be much better than that for comparable results taken over a longer period of time. Consideration of possible causes for these differences led to an investigation of the effects of temperature variations on contact angles. References to literature revealed only a small amount of information, some of it apparently conflicting. Specifically, Sutherland and Wark4/ found that temperature variations "within limits" did not appreciably influence the angles measured for galena conditioned with potassium ethyl xanthate. On the other hand, McGlashan and McLeod5/ presented preliminary data showing that for sphalerite conditioned with potassium ethyl xanthate the angle is maximum at 25° to 35° C., depending on the pH of the system.

Jan 1, 1960

By I. AITKENS

The precious stones rubies and sapphires are transparent varieties of the mineral corundum . Essentially they are aluminum oxide , but the aluminum is often replaced. by small amounts of chromium , titanium , or iron . The chromium is said to give a red color , titanium a blue , and iron a yellow . True rubies range from rose to a somewhat purplish red and are sometimes termed " oriental rubies " to distinguish them from spinel rubies , stones of inferior hardness , density , and value . " Oriental rubies " are very rare , and the so-called " pigeon's blood" variety is the most valuable . Sapphires normally range in color from palest blue to deepest indigo , but actually all precious varieties of corundum of any other color than red are called sapphires . The most esteemed tint is like that of the blue cornflower . Colorless corundum of gem quality is called white sapphire ; the yellow variety is described either as yellow or as golden sapphire ; and the pale pink is classed as pink sapphire . The word " oriental " is also used as a prefix in naming varieties of corumdum of less popular colors . For instance , oriental emerald is used for green corundum, oriental topaz for yellow , and oriental amethyst for violet to purple varieties . The chief physical characteristics of rubies and sapphires are hardness , adamantine luster , and moderately high specific gravity ( 3.9 to 4.1) . Next to the diamond, corundum is the hardest of all minerals ; in fact , the sapphire is number 9 on Moh's scale , ranking between the topaz and the diamond. Rubies crystallize in 6-sided prisms terminated by flat faces and other varieties of corundum with twelve inclined faces , six above and six below , meeting in a girdle . Corundum is doubly refractive , with a direction of single refraction running parallel to the edge of the prism . The refractive indexes are very constant, the ordinary index ranging from 1.766 to 1.774 and the extraordinary index from 1.757 to 1.765. The double refraction always remains the same.

Aug 1, 1931

By I. AITKENS

Turquoise is prized solely for its attractive color ; it is dull and opaque , wholly lacking the brilliant luster that is the chief attraction of transparent gems . The best quality of turquoise is blue , of a soft and pleasing tone , like the color of clear sky but distinctive , as indicated by use of the term " turquoise blue . " Often its value is lessened by a greenish cast ; in many stones the green predominates . A large proportion of the turquoise that is mined is utterly worthless , so inferior and unattractive is its color . The finest grade of turquoise comes from Persia , notable from Nishapur . Large quantities have been mined in the Southwestern States of the United States , and less important deposits have been found in a number of the other States .

Sep 1, 1931

By Robert Lundquist

REAM is a unique method of rock breaking using high energy projectile impact. This report-describes the most recent in a series of tests demonstrating mining applications for the REAM method. In an underground limestone mine at Greer, West Virginia, REAM was used to drive a short tunnel and drill a large diameter borehole. Along with breakage data from these tests the goal of the program was to examine environmental problems which might result from the use of cannons under-ground. A total of 103 shots was used to advance a 14-l/2-feet high by 10-feet-wide face a distance of 5-1/2 feet. It is estimated that the 9.3-pound-concrete projectiles launched at 5000 feet per second will break an average of 0.78 tons of limestone or 67 percent of the 1.125 tons of granodiorite broken in previous tests. The 9-inch-diameter borehole was drilled horizontally by repeated axial impact for 7 feet, 2-1/2 inches by 21 shots giving an average of 4.12 inches per shot. Scaling this result to compressible impact energy yields an estimated 5.8 inches per shot for a 12.8-inch-diameter hole compared to 8 inches per ~hot for a 16-inch-diameter hole in granodiorite. Noise measurements indicate that a silenced cannon can be used within a few hundred feet of mine personnel in a room and pillar mine within the legal limit of 140 dB impulse without additional protection. Some fume measurements were made with satisfactory results, even though the military propellants used produce much greater quantities of toxic fumes than the liquid propellant proposed for the future.

Jan 1, 1976

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Uruguay has been prepared from the best available information in Washington, but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State .

Sep 1, 1930

By Perry G. Cotter

The objective of this investigation was to synthesize and investigate the properties of a high-temperature refractory material based on a combination of boron, silica, and magnesium. A magnesium-thermic reaction was used for the synthesis. X-ray examination of the product indicates that the crystalline portion of the composition is a combination of magnesium borides, magnesium silicate, and magnesium orthoborate. Chemical analysis of a representative sample shows, in weight-percent, boron 17.6, silicon 23.9, magnesium 17.8, and chromium 0.5. The balance is largely oxygen. The composition is resistant to high temperatures under oxidizing conditions and is stable in water, hydrochloric acid, and hydrogen. It has a low density (less than 3 grams per cubic centimeter) and a hardness value in the range of quartz. It has a melting point above 1,700° C. and can be hot-pressed to shape in the temperature range between 1,200° and 1,350° C. The properties described in this paper indicate that the material may have some uses as a high-temperature refractory, and because of its boron content it may have some value as a thermal-neutron-absorption material.

Jan 1, 1961

By A. L. Engel

This report is a compilation of preliminary and, in some cases, more extensive concentration experiments by the Federal Bureau of Mines on low-and medium-grade fluorspar ores from three localities in Nevada and one in California. The work was done on samples obtained from Shoshone mine, Nye County, Valery mine, Pershing County, and the Broken Hills mine, Mineral County, all in Nevada, and Dirty Weather mine, Inyo County, Calif. These investigations were made to aid in the development of domestic fluorspar resources, in line with the Bureau's long-established program of conservation of mineral resources. The treatment methods employed in the experimental work described included simulated or "heavy-liquid" gravity concentration of coarse minerals and comparatively fine-grained minerals, and flotation concentration of finely-ground minerals. These methods were attempted in order to beneficiate the ores and produce concentrates which could be marketed readily, with as high a recovery rate as possible, while using simple treatment methods suitable for small-scale operation.

Jan 1, 1961

By Ε. P. YoUNGMAN

This paper presents one of a series of digests of foreign mining legis- lation and court docisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in vericis foreign countries. This interpretation of the laws - of Italy has been prepared, in part, from an aclysis made by John W. Frey, for merly associate mineral economist, U. S. Bureau of Mines. It incorporates addi- tional data and comments offered by Enrico Giobbe Della Pitta, a well-known Italian lawyer, in response to a questionnaire. These comments were forwarded by Harold H. Tittmann, American chargé d'affaires ad interim, at Rome, and trans- mitted to the Bureau of Mines through the courtesy of the Department of State.

Oct 1, 1930

By Wallace W. Roepke

The Bureau of Mines has a well-established health and safety research effort directed to fundamental studies of the mine cutting system. This report describes the ignition danger of using cutting bits with flat wear area on still-intact carbide inserts.

Jan 1, 1983

By Robert J. Evans

Capital and operating costs were estimated using a wet suppression, fabric filter, and a combination system of the two for hypothetical hard rock stone crushing plants located in central Pennsylvania, operating at 300, 600, and 1,000 tons per hour. Fixed capital expenditure for the dust abatement systems ranged from $49,129 to $249,162. Annual operating costs for the dust abatement systems ranged from $8,394 to $46,606 (0.9 to 3.2 cents per ton). If these dust abatement systems are properly sized, installed, and maintained, efficiencies approaching 95 percent can be expected for reduction in weight of dust particles emitted before control.

Jan 1, 1975

By C. Özgen Karacan

Degasification and methane control in underground coal mining is an important area augmenting conventional ventilation in order to prevent possible fires and explosions due to excessive methane emissions. Coal bed reservoir engineering has been applied for many years to coalbed methane production. In recent years, modeling the flow and draining methane, not only from coal bed itself but also from the overlying strata, have been recognized as important areas of expertise for supplementing underground ventilation. This paper demonstrates the applications of coal bed reservoir engineering and modeling techniques for optimizing and controlling methane emissions in longwall and continuous miner sections. Practical applications and some considerations are presented for reservoir modeling, borehole performances, and face emission predictions for various coal bed and borehole configurations. A section on field reservoir studies and well bore log analyses for methane control are also presented as a complementary way of controlling methane and optimizing ventilation.

Jan 1, 2009

By L. E. Schultze

[The Bureau of Mines conducted bench-scale studies to develop techniques for stripping tetravalent cerium from tri-n-butyl phosphate solutions. Experiments were conducted in a constant-temperature bath using beakers and mechanical stirring. Ninety-five pct of the cerium was stripped from a 50-pct tri-n-butyl phosphate 50-pct kerosene solution containing 0.18 M cerium in 15 minutes at 50° C using 0.11 M aqueous formaldehyde.]

Jan 1, 1974