Search Documents

By C. Özgen Karacan

This study presents the results of core-log analyses from the exploration boreholes, the analyses of face advance rates, and the results of downhole monitoring studies performed in gob gas ventholes for calculation of changes in hydraulic properties in the longwall overburden at a mine site in southwestern (SW) Pennsylvania section of Northern Appalachian Basin. In the ?rst part of the study, coal measure rocks in overburden strata were analyzed and the locations where possible fractures and bedding plane separations would occur were evaluated. In the second part, the hydraulic conductivities were computed by two different slug test analyses methods using the water level changes measured in gob gas ventholes as longwall face approached. Hydraulic conductivities were analyzed with respect to the changes in overburden depth, the locations of the borehole, and mine face advance rates. These data were used to interpret the potential productivities of the gob gas ventholes as a result of fracturing and changes in hydraulic conductivities. The general results showed that the probability of fracturing and bedding plane separations in the overburden increase between strong and weak rock interfaces. Also, the probability of bedding plane separations increases as the interface is close to the extracted coal seam. Evaluation of slug tests showed that the hydraulic conductivity developments in the boreholes and their potential production performances are affected by the underground strata and the roof materials. In situations where the roof material is stiff and thick, the development of high permeability fractures around the borehole will be less. Results also indicated that borehole location with respect to face position affects the fracturing time and permeability evolution as well. Greater overburden depths generally cause earlier fracturing as longwall face approaches, but eventually result in lower hydraulic conductivities and potentially less effective boreholes. Increasing mining rates also resulted in generally lower hydraulic conductivities in the overburden. The results of this study were intended to improve the interpretation of gob gas venthole performance and to provide better siting of these boreholes.

Jan 1, 2009

By A. J. Miscoe

A unique machine for inducing bending fatigue in wire ropes was built at the U.S. Bureau of Mines' Pittsburgh Research Center. This machine can produce nine levels of degradation through repetitive cycling of long samples of wire ropes of the types used in the mining industry. This report provides an analysis of the results of the first wire rope to be fatigued on this machine. These results have indicated that as a wire rope accumulates bending cycles, its strength first decreases because of wear and then in-creases due to cold working of the wires. As the amount of cold working increases, more and more of the embrittled wires break and the strength of the rope decreases rapidly. In this test, application of several of the regulatory retirement criteria to various sections of the rope suggests that there may be some inconsistency among them.

Jan 1, 2010

By C. W. Smith

The Bureau of Mines conducted laboratory-scale beneficiation tests on a sample of corundum gneiss from Montana to devise a method for beneficiating corundum for use as a substitute for refractory-grade bauxite. A flotation process utilizing petroleum sulfonate as the collector in an acid circuit was devised. Results showed that two flotation schemes each produced a concentrate exceeding the national stockpile specifications for calcined bauxite. From a feed containing 28 pct corundum concentrates containing up to 92.5 pct alumina (A1203) were produced with a corundum recovery of 78.5 pct.

Jan 1, 1987

By Robert H. Merrill

Measurement of the deformation of a borehole in rock subjected to a change in applied stress can be used to calculate the magnitude and direction of the applied stress, provided a satisfactory deformation-applied stress relationship exists , In this investigation by the Bureau of Mines the deformation of a bore- hole in a rock model subjected to a known applied stress was compared with the theoretical deformation of a hole in an elastic, isotropic plate and was found to be in good agreement. Hence, this relationship can be used to calculate the applied stress on a borehole from borehole deformation measurements.

Jan 1, 1961

By W. E. Wallace

Volume-rate-of-flow measurements were made of the flow of mercury through porous samples under conditions of no field, magnetic field transverse to the direction of flow, and transverse magnetic field and electric current to determine if a magnetic method might be potentially useful in the study of pore-size distribution. No change was observed in the flow rate from the application of a magnetic field alone. The application of both field and current produced an electromagnetic pumping action with or against the direction of flow, depending upon the direction of the electric current. This pumping effect was observed to be greater in a rectangular porcelain sample than the calculated value for an equal-Sized open channel.

Jan 1, 1969

By Lloyd A. Morley, Alan M. Christman

PART A. ELECTRICAL EQUIPMENT – GENERAL Paragraph 1. Electrical Equipment; Examination. All electric equipment shall be examined, tested, and properly main¬tained by a qualified person to assure safe operating conditions. The examinations and tests shall be performed at intervals not exceeding six (6) months unless otherwise specified in Parts A, B, C, D, and E. When a potentially dangerous condition is found on electric equipment, such equipment shall be removed from service until such condition is corrected. A record of such examinations shall be kept and made available to an authorized representative of the Secretary and to the authorized repre¬sentative of the miners in such mine. Each item of major equipment, in¬cluding substations, switchgear, load centers, and so forth except powered hand tools, shall be recorded separately. The record of such examination shall include all dangerous conditions found, corrective action taken, and name of examiner, and shall be signed by the person responsible for main¬taining the equipment in safe operating condition, who shall also be a qualified person. Paragraph 2. Electrical Work; Qualified Personnel. No electrical work shall be performed on electrical distribution circuits or equipment, except by a qualified person or by a person trained to perform electrical work and to maintain electrical equipment under the direct supervision of a qualified person. Disconnecting devices shall be locked out and prominently tagged by the persons who perform such work, except that in cases where locking out is not possible, such devices shall be opened and prominently tagged by such persons. Locks and tags shall be removed only by the persons who installed them or, if such persons are

Jan 1, 1976

By W. E. Wallace, C. A. Hill, M. J. Keane

"Diesel exhaust particulate material from exhaust pipe scrapings of two trucks, diluted automobile diesel exhaust particulate material collected on filters, and two oil shale ores were prepared for the Ames mutagenrcity assay by dichloromethane OOP ex¬traction, by dispersion into 0.85% saline, or by dispersion into dipalmitoyl lecithin (DPL) emulsion in saline. Salmonella typhimunum TA98 was used to detect frameshift mutagens in the samples. Samples of diesel soot gave positive mutagenic responses with both DCM extraction and DPL dispersion, with the DPL dispersion giving higher results in some cases. The results suggest that possible mutagens associated with inhaled particles may be dispersed or solubilized into the phospholipid component of pulmonary surfactant and become active in such a phase.INTRODUCTIONThe Ames Salmonella/microsome assay (Ames et al., 1975) has been shown to be a useful test for detecting genotoxic properties of various agents. Hundreds of specific chemicals have been screened (McCann et al., 1975), and the test has been applied for many types of environmental samples. Airborne mutagenic agents, for example, have been found in urban air (Chrisp and Fisher, 1980; Hughes et al., 1980; Ro· senkranz et al., 1978), in diesel engine exhausts (Huisingh et al., 1978), and in the by-products of coal combustion processes (Chrisp et al., 1978).Samples of airborne particles are typically collected on membrane filters, and undergo a rigorous extraction procedure with organic solvents and/or ultrasonic agitation (Clark and Hobbs, 1980). Often extracts are transferred to another solvent that is compatible with the assay system. These extraction procedures, while efficient from an analytical perspective, are not physiologically plausible. The questions that present themselves are whether a demonstrated mutagen can be taken up in vivo and whether the process is quantitatively or qualitatively different from the above laboratory procedure (Wallace et al., 1984).When a particle of respirable size is inhaled to the alveolar region of the lung, its first physiological contact is with pulmonary surfactant that lines the inner surfaces of the alveoli. This surfactant is an aqueous fluid containing proteins, phospholipids, and other components (R. J. King, 1982). The principal phospholipid constituent is L·alpha-phosphatidylcholine, beta,gamma-dipalmitoyl, or dipalmitoyl lecithin (OPL) (l. C. King et al., 1981)."

Jan 1, 1989

By Foster Fraas

A separator for minerals of low magnetic susceptibility and fine particle size in a water suspension is described. A ring-shaped matrix of ferromagnetic fragments rotating so as to pass successively through magnetic-field and field-free regions provides for the separation. Application is illustrated in the separation of hematite and ilmenite from quartz.

Jan 1, 1966

1. In 2003, a total of 7,070 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA). The largest percentage of all mining sectors was sand and gravel mines (49.1%). • Sand and gravel mines are found throughout all 50 states.

Feb 1, 2005

By Joan Weinberg

The real gross national product (GNP) advanced at a annual rate of 3.1 % during the second quarter, following a revised 3.4% increase in the first quarter (see table 1). Export growth continues to play an important role in the rising output. Combined with the decline in imports, it resulted in a noticeably improved trade position. Imports of consumer goods, including automobiles and food, fell while exports rose. Imported cars have been losing ground to domestic cars. The foreign car share of the U.S. market fell from 36% in October 1987, to 29% in May 1988. Business spending for new plant and equipment contributed strongly to the GNP increase. Equipment purchases, particularly of computers, rose at a 14.8% annual rate, following a large first-quarter gain. Purchases of structures rose 11.8%. The other key component of business spending, change in business inventories, declined from the first quarter. Inventory buildup in late 1987 had been considered excessive.

Jan 1, 1988

By W. Beckering

IN CHARACTERIZING tars obtained by the low-temperature carbonization or North Dakota lignite, infrared spectra have been an invaluable aid in both qualitative and quantitative examination. Quite early it became evident in the tar-research program of the Bureau of Mines, U.S. Department of the Interior, that the small number of published spectra available for hydroxy aromatics would be inadequate for comparative purposes when dealing with the wide range of compounds present in coal tar; therefore, compiling a catalog of spectra was initiated as a continuing part of the tar program. As these spectra should be valuable to other investigators in this and related fields, they are being presented in this report. This group or spectra (figs. 1-98) represent 97 compounds, largely phenolic materials. The major problem of this project has been the availability of materials for examination. Samples have been obtained from commercial and private laboratories or synthesized at the Bureau of Mines Lignite Experiment Station, Grand Forks, N. Dak.

Jan 1, 1959

By R. W. Dalzell

The performance characteristics, efficiency, and operating pressure of jute line-brattice systems were studied under varying underground conditions; various fabric grades and installation methods were used. The test results indicate that line-brattice system efficiency is dependent upon the method of ventilation the method of installation, porosity of fabric, and size of tight rib area.

Jan 1, 1966

By George E. Fish

This report describes investigations conducted by the Bureau of Mines from 1957 through 1959 in the Roseland anorthosite-titanium belt of Nelson and Amherst Counties, Va., for the purpose of studying the titanium resources of the area. Three titanium deposits containing much saprolite ore derived from the decomposition of anorthosite and diorite were selected for detailed study Following a reconnaissance of the reported titanium occurrences in the belt. These three deposits occur in or are associated with anorthosite. Most of the occurrences are situated on or near the contact between the anorthosite and the gneissic country rock. The saprolite deposits are as much as 1.5 miles long, 1,000 feet wide, and 100 teat deep and contain significant reserves of titanium-bearing material estimated in excess of 20 million tons. Where it was penetrated by drilling, the unweathered rock beneath the saprolite contains nearly the same titanium values as the saprolite.

Jan 1, 1962

By D. J. MacDonald

This U.S. Bureau of Mines report reviews published information on synthetic berlinite (AlP04) and suggests experimental conditions requisite for its production. Berlinite is a piezoelectric material with potential use as a substitute for quartz in the crystal oscillators, which are components of electronic and electroacoustic equipment. Information gathered here (mostly from published sources) includes historical background, physical properties, end-use applications, criteria of quality, and physio-chemical factors involved in berlinite crystal growth. It is concluded that growing large high-quality berlinite crystal would require high-purity starting materials in an autoclave equipped with a noncorrodible liner and operated with temperature control of ±O.OO5 ac over a range of 250 to 350 ac.

Jan 1, 1995

By Keith G. Wallace

Coal mine ventilation systems are often subject to high leakage rates. As a result, changes in airflow resistance will strongly affect the efficiency with which air is delivered to the working place. One major source of airflow resistance is the line brattice used to direct air from the last open crosscut to the working face. Because it is a great distance from the fan, the resistance of the line brattice can result in more overall leakage than an equivalent resistance closer to the fan. Substituting auxiliary fans for brattice eliminates this source of resistance, with improvements in system efficiency and cost. Also, in some mines, the leakage that leads to spontaneous combustion can be reduced. The benefits obtained by several different brattice and fan substitutions have been studied by Mine Ventilation Services, Inc., Lafayette, CA, under contract to the U.S. Bureau of Mines. Changes in main fan duty were compared with additional costs associated with auxiliary fans. Results indicate that in some circumstances, considerable leakage reductions and cost savings are possible.

Jan 1, 1990

By Wesley A. Grosh

The Sutherland copper prospect is situated in Floyd County, Va. The immediate area was prospected around 1850, and one of the adits possibly dates from that time. Little or no ore has been mined from the deposit. The deposit is a mineralized sulfide zone occurring in mica schist and consisting mostly of pyrrhotite with minor amount of copper. A magnetometer survey of the deposit by the American Metal Co. in 1939 showed an anomaly that was thought to indicate a zone: of secondary enrichment. The Bureau of Mines diamond-drilled 14 holes, totaling 913 feet, and opened an adit during February and March 1943. No appreciable copper values or indications of secondary enrichment were found.

Jan 1, 1948

By Errol D. Sehnke

This U.S. Bureau of Mines report provides detailed information on worldwide bauxite production capacity by mine and country, including bauxite substitute materials in countries of the former Soviet Union, The information was compiled from a variety of domestic and international sources and was based on information available to the Bureau through December 31, 1994. Capacity data represent announced installed and planned capacities and do not necessarily reflect a U.S. Bureau of Mines judgment of actual mine operating levels or timing of planned expansions. The year-end capacity is the ?in place? capacity or estimated production capacity, whichever is larger.

Jan 1, 1994

By John C. Machisak

THE INJURY data and experience at quarries and related plants of the United States are presented in this publication under the following general sections : (A) General injury experience: Tables 1 through 3: Contain current data on the number of injuries, injury-frequency rates, location, accident agency, degree of injury, and related employment data. (B) Injury experience at different kinds of quarries: Tables 4 and 5: Contain current data on number of injuries, injury- frequency rates, location, accident agency, degree of injury, and related employment data. (C) Injury experience by States: Tables 6 through 19: Contain current data on the number of injuries, injury-frequency rates, accident agency, degree of injury, and related employment data.

Jan 1, 1959

By R. J. SHAW

Oil shale has been defined as, "a compact, laminated rock of sedimentary origin yielding over 35 percent of ash and containing organic matter that yields oil when distilled but not appreciably when extracted with the ordinary solvents for petroleum." The oil-yielding organic matter in oil shale, commonly called kerogen, decomposes upon application of heat to form bituminous materials that are soluble in organic solvents and may be extracted from the inorganic residue. However, separation usually is accomplished by continuing the heating and thereby cracking the primary bitumens to gas and oil, which distill, leaving a carbonaceous material on the mineral residue. It has been suggested that this conversion takes place only at relatively high temperatures - 750°F or higher. On the other hand, other workers have found that transformation may take place to some extent at temperatures as low as 400°F. In either a solvent extraction or a destructive distillation process for separating organic material from the inorganic portion of oil shale, the quantity of heat required to raise the temperature of the oil shale sufficiently to induce a satisfactory rate of conversion of kerogen to oil is important in determining the design of an economical process. Likewise, the quantity of heat recoverable from a spent shale is important in determining the overall heat balance of the process. Published data on the specific heat of American oil shales are meager. Gavin and Sharp present data for two samples of Colorado oil shale, one from near DeBeque and one from Parachute Creek, and for a sample of spent shale over a temperature range of 68°F to 1940°F. McKee and Lydor present data on the specific heat of two samples of oil shale from near DeBeque, Colorado. Additional thermal data on various grades of oil shale over a wider range of temperature are needed in order to apply sound engineering practices to the design of equipment for processing oil shale.

Nov 1, 1947

By R. E. Meaker

Electrical conductivities and densities of molten fluoride systems were measured as functions of the melt temperature and composition. For any given mixture, the two properties change linearly with temperature. Three alkali metal fluorides were selected as solvents for melts of the type LiF-, NaF-, and KF-MFx, where M is a metal selected from the alkali metal or alkaline earth groups, or from the lanthanide or actinide series of elements, and x = 1-4. Heats of activation for conductance were calculated from the experimental data and varied from 2.3 to 9.2 kcal/mole at 1,000° C. Some relation between position in the phase diagram and the conductivity changes was suggested.

Jan 1, 1971