Search Documents

By E. D. Calvert

As part of its goal to minimize the requirements for critical and strategic minerals, the Bureau of Mines is conducting research to foster the use of domestically abundant materials such as molybdenum. This report describes the development of an investment shell molding technique that can be used to make castings of molybdenum and its alloys. The mold material is cubic Zr02 with a monoclinic Zr02 binder. The shell, formed by standard investment molding techniques described in the text, is prepared for molybdenum casting by firing for 6 hours at 1,550° C (2,822° F) or for 4 hours at 1,650° C (3,002° F). The resulting castings have predictable and reproducible dimensions with good detail. As-cast strength is poorer than the strength of wrought materials below 1,600° F. At and above this temperature, tensile strengths of cast and wrought materials are nearly equal. Aqueous corrosion of the castings in most media is insignificant.

Jan 1, 1982

Increase the productivity of domestic mining operations by improving the performance of rock drilling systems. Approach Investigate the use of chemical solutions at zero surface charge concentrations as drilling fluid additives to enhance penetration rates and extend bit life. Background Bureau researchers have investigated the use of chemical additives to enhance drilling performance and have found that the most efficient drilling occurred when the drilling fluid was able to maintain a zero surface charge (ZSC) on the rock surface. Laboratory drilling studies using 5/8-inch diameter diamond-impregnated coring bits on rock types such as quartzite, granite, taconite, and marble. Cationic compounds were used as the surface charge neutralizing additives during these tests. The drilling studies demonstrated enhanced drilling performance, however, only at the singular additive concentration that produced the ZSC condition. Bureau researchers made a breakthrough when they found that polyethylene oxide, although a nonionic polymer, was able to maintain the ZSC condition over a wide range of concentrations. Success using polyethylene oxide as the drilling fluid additive during subsequent laboratory tests prompted testing under field conditions.

Jan 1, 1991

By Robert F. Kehrman

As with many new technologies, the rapid growth in solution mining for uranium has created uncertainties regarding the environmental impact of mining operations. In solution mining, the largest area of concern is the impact of the process on the quality of ground water supplies. As a result, a rapid and reliable technique of detecting lixiviant excursions is desirable. Such a method would replace the periodic sampling technique and should provide a more or less continuous monitoring method. To this end, resistivity techniques were evaluated as an alternate means of tracking lixiviant movement. A program was devised which had five specific tasks. These were: (1) evaluation of the techniques, (2) development of the most promising technique or techniques, (3) field testing of the techniques, (4) testing of the BuMines probe, and (5) reporting. The result of the analytical and field work is that various resistivity/ resistance techniques do provide a means of detecting lixiviant movement in Northern Wyoming. Surface and downhole galvanic surveys and controlled source audio magnetotellurics (AMT) were evaluated. All three techniques showed some degree of success.

Jan 1, 1979

By Green R. E.

The removal of silica from commercial iron oxide concentrates by dissolution with sodium hydroxide was investigated by the Bureau of Mines as a means for producing supergrade concentrates. The effects of strength of solution, temperature, and digestion time on the extraction of silica were evaluated using eight iron oxide concentrates. Silica extraction from the eight concentrates was enhanced by autoclave leaching in the temperature range of 150° to 250° C and varied from 70 to 95 pct depending on the concentrate used. Superconcentrates containing less than 2 pct Si02 and more than 69 pct Fe were made only when magnetite concentrates were leached in the autoclave. The investigation showed that it is not difficult to obtain a supergrade product if the gangue is mainly quartz.

Jan 1, 1973

By Omotayo Kalejaiye

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRL 20-L and Fike 1-m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface-weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1-m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

Jan 1, 2010

By James P. Bennett

The Bureau of Mines investigated the effect of refractory oxide additions, introduced in soluble form, on the high-temperature properties of 90- and 98-pct-MgO brick. Brick samples were soaked in solutions containing Al, Ca, Cr, Co, Fe, Mg, Mn, Mo, Ni, Si, Sr, Sn, Ti, or Zr ions. Additions to 98-pct-MgO brick did not generally result in statistically significant property improvements. Statistically significant improvements were noted in hot modulus of rupture (MOR), slag resistance, and spalling resistance of the 90-pct-MgO brick for additions of Al, Mg, or Sn. High-temperature performance of treated 90-pct-MgO refractories was equal to or approached that of 98-pct-MgO brick. The marked improvements due to tin were obtained with additions of only 1.14 wt pct Sn02.

Jan 1, 1985

By G. H. Cobb, J. L. Johnson, H. H. Heady

An infrared absorbance technique is described for analyzing anodic gases produced during the electrowinning of uranium , thorium , and rare - earth metals in molten fluorides . Typical components determined qualitatively in a gas sample are CO , CO₂ , CF4 , C₂ Fe , C3F8 , COS , CS₂ , and SiF4 . About 20 minutes are required to record and interpret the spectrogram , and report quantitative results for CO, CO₂ , CF4 , and SiF . The procedure is used for control during electrolysis .

Jan 1, 1964

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines have been exploring recent advances in the use of strain-softening constitutive laws that approximate shear fracturing. The purpose of these tests is to investigate shear-fracture-related rock bursts in hard-rock mines. The capabilities and remaining problems in the use of strain-softening laws in finite-element, distinct-element, and finite-difference methods are reviewed. Performance of the finite-difference implementation of strain softening is compared to classic experimental results and observations of rock mass behavior in the Coeur d'Alene Mining District of northern Idaho. The results show promise for developing methods to identify the general location and orientation of shear fractures and their sequence of occurrence, but such methods cannot be relied upon to quantify post-fracture loads or displacements accurately. Uncertainty over the amount of energy consumed by failing rock and the dependency of energy consumption on model mesh definition prevent direct application of the results to analyses of rock bursts.

Jan 1, 2010

By R. A. Cortese

The U.S. Bureau of Mines has developed a flame-radiation-powered trigger device to explosively activate suppression barriers to quench gas and coal dust explosions. The major component of the device is a silicon solar panel, which converts radiation from the developing explosion into electrical energy to initiate an electric detonator, which releases an extinguishing agent into the advancing flame front. Solar panels that are rated to produce 20 W of electrical power when exposed to the sunlight are producing about 200 W when exposed to a full-scale dust explosion. The solar panel is electrically isolated from the detonator by a pressure-sensitive switch until the arrival of the precursor pressure pulse, which always precedes a deflagration. This combination of pressure arming and flame-powered photogenerator prevents false barrier activation and requires no external power supply.

Jan 1, 2010

By N. S. Dalal, X. Shi

While it is known that vanadate and related compounds of pentavalent vanadium ( V (V)) exert potent toxic effects on a wide variety of biological systems, the underlying biochemical mechanism is still not fully understood ( 1- 3). One of the pathways is thought to involve the oxidation of NAD ( P) H. Thus, considerable effort has been devoted to finding the mechanism of NAD ( P) H oxidation by Vcvi (1-15). Erdmann et al. (5) first noted that vanadate stimulated the oxidation of NADH by plasma membranes and attributed this effect to a membrane containing NAD(P)H-dependent V(V) reductase. Later studies by Liochev and Fridovich indicated that endogenous superoxide ( 02 ) plays a central role in this reaction ( 4, 12, 13) . They proposed that NAD ( P) H dehydrogenases or oxidases produce 02, which causes VCV ) to stimulate NAD ( P) H oxidation via the following free radical chain mechanism ( 4, 12, 13) :

Mar 1, 1992

In this U.S. Bureau of Mines report, proposed narrow-vein and longwall mining concepts using drill-split technology (described in part 1 of this series) and in situ liner concepts (described in part 2 of the series) are combined and applied conceptually to environmental problems. Proposed applications deal with (1) acid mine drainage (AMD), (2) solid waste disposal, (3) site remediation, and (4) pollution prevention through innovative industrial design. For control of AMD from abandoned hillside mine workings, it is proposed that source veins be re-mined, processed for residual values, then backfilled using an impermeable compound backfill mix. For solid waste disposal, "vertical landfills" are proposed, consisting of trash-backfilled underground rock quarries. Vertical landfill activities take place in in situ lined containments that geohydrologically isolate the mining-backfilling activities. Site remediation through the creation of in situ underliners, for the capture of toxic leachates, and pollution prevention through the underground storage of toxic, flammable, and explosive materials in in situ containments, are proposed.

Jan 1, 1995

By John E. Rourke, O&apos

A survey of existing and developing field permeability test methods was conducted in order to identify and specify capable methods to be used in feasibility investigations or performance monitoring for in situ leaching of ore deposits. Geologic settings of leachable deposits are discussed, as well as representative techniques used for the in situ leaching operation. Subsurface investigation techniques including drilling, core recovery, and down-hole inspection methods relevant to field permeability investigations are discussed. Field experience is examined and capable field permeability test methods are identified. Specifications for test borehole preparation, test performance. and methods of analysis are given. The test methods are comparatively rated in a matrix with respect to costs ease of use, and data effectiveness' for a broad range of conditions. Well Pump and Packer test methods receive high ratings. Recommendations are made for needed developments in field permeability test methods and a comprehensive bibliography is given.

Jan 1, 1977

By R. V. Ramani

"In Part 1 of this paper, published in the August 1995 issue of Natural Resources Forum, a review of several mining disasters around the world established the complex nature of their causation and their catastrophic effects. The involvement of human beings, either through acts of commission or omission, was highlighted. In Part 2, a discussion of the various approaches to disaster control, mostly as practised in the USA, is presented. A systems approach to disaster prevention incorporating elements of hazard identification, mine design, emergency response and post-emergency audit is presented.In the USA the role of government in the affairs of its citizens is continually growing. This role is intended to ensure an unimpeded pursuit of happiness and prosperity by the population and to curtail actions which are restrictive or harmful to the citizenry. The passage of a legislation is an indication that it has been decided through the established process that the activities covered by the legislation should receive appropriate consideration. The enactment of the Coal Mine Health and Safety Act of 1969 (The 1969 Coal Act), the Mine Safety and Health Amendment Act of 1977 (The 1977 Mine Act) and the Surface Mining Control and Reclamation Act of 1977 (The 1977 Surface Mining Act), was specifically intended to further the role of government in the health, safety and environmental affairs of the mineral industry.Currently, the federal government's responsibilities for mine safety and health are divided among three agencies: the Mine Safety and Health Administration (MSHA) in the US Department of Labor, the Bureau of Mines (USBM) in the US Department of the Interior and the National Institute for Occupational Safety and Health (NIOSH) in the Department of Health and Human Services (National Research Council, 1981). MSHA is responsible for issuing and enforcing mine safety and health regulations, for training miners and for responding to mine emergencies. The Bureau of Mines is responsible for conducting research on mine safety and on the technological means for reducing health and safety hazards in mines. NIOSH conducts research relating to miner health, and together with MSHA, tests and certifies devices used to detect hazardous materials in mines and protective equipment used by miners. NIOSH also plays a public health role in that its activities in mining include health hazard evalua¬tions, general mining surveillance as mandated by law and medical surveillance including coal miner X-ray and autopsy programmes. MSHA shares with the Bureau of Mines the responsibility for integrating R&D results into operational practice. MSHA implements R&D results either by incorporating them into its own operations or by rule making that requires new practices or equipment to be adopted by the mining industry. In many instances, the Bureau's R&D results have been adopted by the mining industry without rule making."

Dec 1, 1996

By David C. Oyler

The Bureau of Mines is cooperating with the U.S. Department of Energy in a directional degasification project at the Emerald mine near Waynesburg, Pa. This project is designed to combine the highly successful underground horizontal degasification technology with surface drilling methods. The objective of this program is to demonstrate that directional drilling can be used as a technique for degasifying coalbeds ahead of mining to reduce the hazards of methane-air explosions in coal mines. The directional hole at the Emerald mine is designed to start vertically and enter the Pittsburgh coalbed horizontally. A 3-inch-pilot hole entered the Pittsburgh coalbed at a vertical depth of 999 feet. The hole will be reamed to 8-3/4 inches in diameter, and 5-1/2-inch casing will be cemented in place. Three individual 3-inch-diameter, 3,000-foot horizontal gas collection holes will be drilled into the coalbed in a "bird foot" pattern. A corehole and vertical dewatering hole have been completed at the anticipated coalbed intercept. The dewatering hole was drilled to 130 feet below the Pittsburgh coalbed, a depth of 900 feet, and 880 feet of 7-inch-OD casing was cemented in place. Seven vertical holes for monitoring the extent and progress of degasification have been drilled within the horizontal drilling area.

Jan 1, 1979

By Maria I. De Rosa

The major fire and fire injury findings for all metal/nonmetal mining categories for 1990-2001 are shown in tables 64-65. Table 66, partly illustrated in figure 22, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays for all metal/nonmetal mining categories by time period. For all metal/nonmetal operations (including stone and sand and gravel), a total of 518 fires occurred during 1990-2001; 296 of those fires caused 308 injuries and 4 fatalities (Ewhr = 4,012 x 106 hr, In = 0.015, LWD = 36,204). Thirty fires and 26 injuries involved contractors. The greatest number of fires and fire injuries occurred at surface operations; the highest risk rate values were also calculated for surface operations. The number of fires increased during the first four 2-year time periods (1990-1991, 1992-1993, 1994-1995, and 1996-1997), then decreased during the last two periods (1998-1999 and 2000-2001). The number of injuries showed a decrease throughout the periods, accompanied by an increase in employees' working hours. Twenty-five firefighting interventions by mine rescue teams in underground mines and at least 30 interventions at surface operations were required to combat these fires. However, 45 fires destroyed or heavily damaged facilities and equipment (including 19 pieces of mobile equipment) because of failure of firefighting methods, late fire detection, undetected fires, or fire size. Ninety-seven fires were detected late, and 30 fires were undetected. The ignition sources that caused the greatest number of fires were flame cutting/welding spark/slag/flame (169 fires or 33% with 137 injuries), hydraulic fluid/fuel sprayed onto equipment hot surfaces (89 fires or 17% with 46 injuries and 3 fatalities), heat source/explosion and flammable liquids/ gas/refueling fuel on hot surfaces (98 fires or 19% with 73 injuries), electrical short/arcing (51 fires or 10% with 16 injuries), and spontaneous combustion/hot material (46 fires or 9% with 17 injuries). The flame cutting/welding spark/slag/flame source caused fires usually involving welders' clothing or oxyfuel/grease and other materials (including chute and dust collector liners, flammable liquids, belt material, crusher, hopper and shaker deck materials, washer plants, equipment mechanical components, stampler breaker, hydraulic fluid, rubber tires and hoses, gear boxes, bin feeder, dump rope cables, screen liner and screen panel, kiln and shaft material, pipelines, liquor pumps, wood pallets, electrical junction boxes, handrails, grease, refuse, shop and wood). The spontaneous combustion/hot material and electrical fires were usually detected late due to lack of combustion gas/smoke detection systems. At least 55 of the 89 mobile equipment hydraulic fluid/fuel fires became large fires (requiring 12 mine rescue team interventions in underground

Jan 1, 2004

Any communication system requires at least three elements in order to function: a transmitting device, a receiving device, and a transmission line or propagation medium. Even the device children use, tin cans connected with string, consists or these three elements. One speaks into one can (transmitter), which vibrates at the same frequencies as the voice. The string (transmission path) picks up the vibrations of the can and carries them along its entire length. The other can (receiver) detects the vibration and reproduces the original sounds to a lesser extent depending on distance, tightness of string, type of string, etc. All communication systems depend on these three elements: transmitter, transmission path, and receiver. Communication systems can be divided into three fundamental categories: wired phone systems, radio systems, and carrier current systems. Sections 2.2, 2.3, and 2.4, respectively, describe these systems and explain the basic principles of how each works. Hybrid systems are those systems that use various combinations of the three basic communication methods. Hybrid systems are described in section 2.5. There are some other methods of signaling (stench warning, bell signaling, etc.) that can be used in underground mines to transmit or convey information. These systems, although they cannot be considered true communication systems since they do not provide voice or even two-way communication, are briefly described in section 2.6. 2.2 Wired Phone Systems Wired phone systems are all those that depend on a wire connection between phones with the wire carrying the voice signals. Figure 2-1 is a diagram of two typical wired phone systems.The top panel shows a simple single pair party line system. In this system each phone is connected to a common pair of wires, and a person speaking into one phone will be heard at all the other phones on the line. The bottom panel shows a multipair private line phone system. In this type of system, each phone is connected by its own individual pair of wires to a central switch or telephone exchange. To establish a call between two phones in this system, the lines between the two phones must be connected (switched together) within the telephone exchange. In early exchanges, the connections were made manually by an operator. These exchanges are called Private Branch Exchanges (PBX's). Today, equipment within the exchange can automatically connect each phone to any other phone in the system. These exchanges are called Private Automatic Branch Exchanges (PABX's). There are many different types of automatic exchanges. Some utilize switches to physically make each connection according to the number dialed. Other, more advanced exchanges are completely solid state and may even be computer controlled. [ ]

Jan 1, 1984

By Jack C. White

This U.S. Bureau of Mines report assesses the resource potential of trace metals present in commercial Ti mineral concentrates. Metals of greatest interest: are those defined as "strategic and critical" by the U.S. Congress in 1981. Metals of interest in Ti mineral concentrates are Cb, Cr, Ta, Th, U, V, and Zr. Commercially available Ti mineral concentrates were studied. Characterization and analysis of major and minor constituents were performed by X-ray diffraction, neutron activation, inductively coupled plasma emission, atomic absorption, and classical wet chemical techniques. Of the metals investigated, the Cb, Ta, and V content of some concentrates may be a significant potential resource, depending on their amenability to recovery.

Jan 1, 2010

By John Owens, Hamid Maleki

Efficient and safe use of mobile roof supports (MRS) depends on the interaction between the MRS and coal strata. Of particular interest to this study are the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods, and MRS load-bearing capabilities. To provide a better understanding of the mechanics of strata deformation, the authors have collected and reviewed measurements of convergence and stress in one western U.S. mine and have completed pseudo-three-dimensional, boundary-element modeling for two typical pillar-pulling plans. Stress distribution in the mine roof above pairs of MRS’s was calculated to demonstrate how MRS’s contributed to the control of roof block movements. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal-measure rocks and by pillar-pulling sequences and layouts. MRS’s and other support systems play a critical role in controlling the stability of both the immediate roof and the middle roof for a distance of up to 18 m (60ft) above the seam. MRS’s provide unique ground control advantages over other types of secondary support by significantly reducing the time between mining and installation of secondary support. Although MRS’s are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at near-peak capacity, whereas posts fail and loose their ability to limit mine roof deformation.

By Edward M. Kawenski

Tests were made in the Bureau of Mines Experimental Coal Mine on stop-pings similar to those used in operating coal mines to obtain information on air leakage through the face and the rupture strength of a stopping subjected to a pressure differential. Block stoppings were made from cinder, slag, and gravel aggregates with and without mortared joints and coatings. Sheet stop-pings were uncoated brattice cloth and nylon or brattice cloth and expanded metal-lath coated with asphalt, latex, mortar, or rigid urethane foam. Limited data were obtained on air through stoppings subjected to simulated roof convergence and to shock forces created by the firing of an adjacent charge of explosive. The pressure differential required to rupture stoppings was determined. shows that coating the face of a stopping effectively reduces ail: leakage. Block stoppings, particularly those with mortared joints, are most resistant to pressure and shock forces than are sheet stop-pings. Where ground movement is a factor, sheet stoppings leak less air than block stoppings.

Jan 1, 1965

By R. L. Brown

This report is the 18th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations. The previous 17 reports have covered fiscal years, but this report covers not only the fiscal year from July 1, 1952, to June 30, 1953, but also July through December 1953, to bring the report to a calendar-year basis. Most of the material in this report relates to publications issued during the reporting period, Some work is mentioned briefly on which publications have not yet been issued or on which data are riot expected to be published, for security or other reasons, and in a few instances publications issues before the reporting period but not included in the previous report are mentioned.3/ Further details on the published work described herein may be found by referring to the publications cited in the footnotes. During the reporting period, the Bureau directed its research and technologic work on coal toward developing end encouraging increased conservation and more efficient use of our mineral fuel resources through more efficient and safer mining methods and improved methods of preparing and utilizing these fuels. Some significant advances, particularly in coal-mine safety, mining methods, and development and utilization of low-rank coma have been made.

Jan 1, 1954