Search Documents

By Deno M. Pappas, Christopher Mark, Eric R. Bauer

During 1998-99, groundfall incidents resulted in 27 fatalities and were responsible for over 70% of all deaths in U.S. underground coal mines. To obtain a better understanding of where and why these incidents occurred, a comprehensive analysis of ground fall injuries and fatalities was conducted. The first portion of the study examined various factors associated with roof and rib fall injuries and reportable roof fall noninjuries that occurred during 1995-98. The study found that the room-and-pillar mining method has twice the groundfall incident rate than the longwall method. Mine locations with high groundfall rates seem to correlate to regions where there is a higher concentration of problematic coalbeds. For example, the Illinois Basin has very high groundfall rates, which can be traced back to several key coalbeds-Kentucky No. 13, Herrin/No. 6/Kentucky No. 11, and Springfield No. 5/Kentucky No. 9. High rib fall rates were found in mines located in thick seams. Groundfall rates were found to be 30% to 40% higher during the months of July through September, possibly due to high humidity that may cause the shale mine roof to deteriorate. The second part of the study examined the root causes of failure by reviewing all groundfall fatality reports for 1996-99. Primary and secondary hazard factors were assigned to each groundfall incident. The primaryf actors resulting in these groundfall fatalities were pillar extraction, traveling under unsupported roof, skin failure, construction, longwall faces, intersections, and geologic discontinuities. Defining prominent ground control incident trends and hazards will identify areas where additional study is needed and where innovative solutions need to be developed to reduce these severe occupational hazards.

Jan 10, 2000

By C. E. Henning

The total number of petroleum refineries in the United States on January 1, 1958, was 318 and their total crude-oil throughput capacity was 9,407,707 barrels per day, according to the Bureau of Mines annual survey. During 1957, 3 new refineries began operating while 4 refineries were retired. Although there was 1 less refinery, the total crude-oil throughput capacity at the beginning of 1958 was 284,033 barrels per day, or 3 percent, more than the January 1, 1957, level. During 1957 all refinery districts showed increases in capacity. The largest increase, 27 percent, occurred in the West Coast district followed by the Indiana-Illinois-Kentucky district with 14-percent increase and the Texas Gulf Coast district with 13-percent increase. The national increase in capacity had the effect of raising the capacity of the average refinery from 28,601 to 29,584 barrels per day. New crude-oil capacity under construction on January 1, 1958, totaled 185,265 barrels, and an additional 297,885 barrels capacity was reported building as replacement for existing facilities. Included in total new construction were 2 new refineries, 1 in Washington and another in Texas, with planned processing capacities of 45,000 barrels and 8,550 barrels per day, respectively.

Jan 1, 1958

The Government of New South Wales has granted approval for Hunter Valley Aluminium Pty., Ltd" and Alcan Australia Ltd. to proceed with the building of an aluminum smelter at Lochinvar and the expansion of a smelter at Kurri Kurri. Construction of the smelters is expected to start as soon as the consortium is finalized in early 1982. The smelters are part of a plan to increase Australia's aluminum capacity fivefold to 1.5 million tons by the mid-1980's. CHILE Construction of a $61 million lithium carbonate plant in northern Chile will be started in early 1983 by Sociedad Chilena del Litio Ltdao Production is scheduled to begin in 1984 with an initial capacity of 6,350 tons of lithium carbonate produced from a brine deposit. The firm is owned 55% by Foote Mineral Company, of Exton, Pennsylvania, and 45% by Corporacion de Fomento de la Produccion-CORFO.

Jan 1, 1982

By J. M. Mutmansky, S. Padmanabhan

"The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Ucah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7.The results will be presented using two categories of data collected during two separate phases of the research:(l) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and(2) quartz concentration data from mines chosen at random.The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent."

Jan 1, 1989

By R. T. Johansen

The adverse effects on waterflooding and well-completion methods of clay minerals indigenous to petroleum-production formations recently have received considerable attention. Knowledge of the types and amounts of clay minerals present would allow estimates of the response of such formations to injected or infiltrated water; however, the random distribution of clays in sedimentary formations makes direct evaluation of ?water sensitivity? desirable. A method for the direct evaluation of water sensitivity has been developed, based on measurement of water-vapor adsorption. Correlation of such data with the results of nitrogen-adsorption measurements provides valuable information on the content and properties of clay minerals in sedimentary rocks. The method is relatively simple and has the advantage that it may be used with small, irregularly shaped chips or shale-streaked samples, as well as with typical core samples. Methods previously employed required separating the clay from the rest of the reservoir-sample material and then performing a clay analysis either by X-ray diffraction, differential thermal analysis, liquid permeability, or a combination of these methods (2,3) .3/ This water-vapor-adsorption method requires measuring only a few points on the isotherm to tell whether or not the sample is water sensitive. The goal of these measurements is not to determine the type or amount of clay present, but what will be its sensitivity to flood water. This method gives a direct means of solving this problem.

Jan 1, 1958

By V. A. Nieberlein

This paper presents the results of research undertaken to recover titanium and columbium by low-temperature chlorination of low-grade columbium-bearing ilmenite concentrates, and to simultaneously remove chlorinated impurities from the volatile chlorides without resort to distillation. Coke-reduced ilmenite was chlorinated at 400° to 500° C., and the resulting TiC14 was free of most impurities before condensation. A heated purification column was used wherein various packing materials reacted chemically or physically with the impurities which passed through them in the vapor phase. A nearly water-white TiC14 product was obtained directly. The principal impurities in the titanium tetrachloride were: 0.02 percent Fe, 0.01 percent V, 0.05 percent A1, 0.04 percent Si, and 0.07 percent Cb. This is a less pure product than commercial TiC14. Most of the columbium was recovered as crude CbC15, requiring further refining.

Jan 1, 1960

By F. E. Block, T. T. Campbell, D. Z. Hobbs

Several methods were investigated for the preparation of high- purity elemental boron in an attempt to develop a feasible process for producing boron on a large scale . In the work described in this report , the metal was prepared by metering boron trichloride gas into a crucible containing molten metal reductants . It was necessary to remove reaction byproducts by acid and aqueous leaching . Magnesium and sodium were tested as reductants , but best results were achieved using lithium or zinc as reductants . Contaminants originating from the materials of construction were the chief impurities in boron made by this method . Impurities ranged from 0.5 to 5.0 percent . Impure boron ( 85 to 90 percent ) was also prepared by the magnesium reduction of boron trioxide in a thermite - type reaction . This product contained magnesium as the chief contaminant . Impure boron made in this way could be upgraded by fusing with potassium fluoborate or potassium acid fluoride . After acid leaching the fusion cake , a product containing 95 to 97 percent boron was obtained . Analytical techniques for accurate determination of impurities in elemental boron are a major problem , requiring solution before a valid comparison can be made of the quality of boron prepared by these various methods .

Jan 1, 1964

By Thomas C. Atchison

The experimental work described in this report is part of a continuing study by the Federal Bureau of Mines of the fundamental physical processes involved in breaking rock with explosives. Six explosives were tested for their strain-producing abilities in a dolomitic marble. The explosives selected for testing had a tenfold variation in detonation pressure and a fivefold variation in characteristic impedance (product of loading density and rate of detonation). Strain pulses produced by the detonation of small charges of the explosives were recorded at distances of 5 to 130 feet. Peak strain, ?, was found to decrease with distance, R, in accordance with an exponential propagation law previously determined for other rock types, namely ? = (K/R)e ?aR The absorption constant, a, did not vary significantly with the explosive and was of the same order of magnitude as that for other rock types. The different explosives produced a fivefold variation in the value of the intercept constant, K.

Jan 1, 1961

By G. W. Reimers

Exothermic oxidation reactions of sulfide minerals can produce self-heating situations in underground mines. If the self-heating is unchecked and the resulting heat is not sufficiently dissipated, the result can be spontaneous combustion fires. This U.S. Bureau of Mines report describes laboratory tests conducted to measure the reactivity of pyrite following treatment with additives to counter its self-heating tendencies. Thermal gravimetric analysis (TGA) and isothermal oxidation procedures were used to obtain information on pyrite ignition and the behavior of pyrite during low-temperature oxidation to ferrous sulfate. The determination of treatment effectiveness was evaluated by adding 5 wt pct of the compound to the pyrite before milling. The resulting samples were then heated in moistened air and after 24 h, the amount of pyrite oxidation determined. Results of these tests indicated that several phosphate compounds reduced the oxidation of pyrite to sulfate to about 50 pct or less compared with the oxidation of untreated sample at 200° C. Cupric sulfate reduced oxidation to about 20 pet untreated sample at 200° C. Sodium, calcium, and potassium chloride reduced pyrite oxidation to levels of approximately 15 pct or less of the untreated sample. Using only 1 pct of sodium or calcium chloride was effective in slowing pyrite oxidation to less than 20 pct of the untreated sample.

Jan 1, 2010

By A. F. Colombo, D. W. Frommer

Bench- scale tests were made to determine the applicability of flotation as a means of upgrading finished and semifinished magnetic concentrates prepared from reductively roasted iron ores . Both anionic and cationic flotation methods were used to remove siliceous gangue from the magnetic concentrates and produce upgraded products . Seven magnetic concentrates , containing from 6.7 to 13.7 percent SiO2 , were improved by the flotation treatment , yielding final concentrates containing less than 6.0 percent Si02 . Cationic flotation methods were studied on four of the seven samples ; of this group only one sample yielded better results by cationic flotation than by the anionic method .

Jan 1, 1964

By Lewis V. Wade

This report provides background information concerning a mine roof simulator currently being considered by the Bureau of Mines. The simulator is a mechanical device with the ability to simulate the forces and displacements associated with mine roof over an area 20 by 20 feet. The topics covered in the report include a conceptual description of the system, definition of system capabilities, discussion of how such capabilities were decided upon, description of available control modes, and a comparison between the mine roof simulator facility and similar facilities existing elsewhere.

Jan 1, 1974

By Graham W. Mark

A chemical method of analysis for beryllium was developed recently in Bureau of Mines laboratories. In this method, quinalizarin (1-2-5-8 tetrahydroxyanthraquinone) in N/4 NaOH is used as a colorimetric titration reagent. This solution has a reddish-purple color, whereas the solution containing equivalent amounts of beryllium and the dye is rather blue. In the titration procedure, standard quinalizarin solution is added to the unknown beryllium sample and to two standard beryllium samples of different but known concentrations. Then adjustments in concentrations of BeO in the two known and of quinalizarin in all three are made until the red-violet shade of the unknown is halfway between that of the two knowns. The amount of BeO in the unknown is calculated from the known BeO content of the solutions between which it lies. It is extremely difficult to distinguish the slight differences in shade of these solutions without the use of a proper light filter, especially when the concentration is over 0.1 mg. of BeO, so a study was made of the transmission characteristics of quinalizarin in N/4 NaOH and of the corresponding beryllium complex to determine what filter would give the most contrast.

Jan 1, 1950

By R. Barany

The heats of formation of gehlenite and talc were determined by hydro-fluoric acid solution calorimetry. The results are reported in terms of the constituent oxides (?H298.15 = -31.1 ± 0.5 kcal/mole for gehlenite and ?H298.15 = -44.9 ± 0.3 kcal/mole for talc) and in terms of the constituent elements (?H298.15 = -952.8 ± 0.7 kcal/mole for gehlenite and ?H298.15 -1,415.5 ± 1.4 kcal/mole for talc).

Jan 1, 1963

By J. B. Gayle

Coke-pushing difficulties have been the subject of much controversy but relatively little scientific investigation. Nevertheless, continuing pushing difficulties can greatly decrease the life of a coke oven and should therefore be considered in the selection of the blend and operating conditions used for coke production. The present Federal Bureau of Mines investigation was undertaken to correlate results of previous investigators and to supplement these results to the limited extent practical by us of an experimental slot-type oven. To this end, pushing pressures have been determined routinely for Tuscaloosa oven tests conducted during the past 10 years. Nevertheless, the accumulated information remains incomplete in many respects, and in view of the recognized inadequacies of the data, publication is now undertaken only because of the scarcity of published information on this important problem and the discontinuation of carbonization studies with this oven.

Jan 1, 1961

By R. P. Vinson

The Bureau of Mines evaluated two real-time light-scattering dust monitors by measuring their response to Pittsburgh Seam coal dust and Arizona road dust (ARD). Both monitors, the model PDS-l, a personal dust sensor, and the model PCD-l, a digital dust indicator, are made in Japan by Sibata Scientific Ltd. Tests were conducted inside a laboratory aerosol chamber designed to maintain a uniform spatial distribution of the test dust. PDS-l and PCD-l measurements of concentrations for each test dust were averaged over 4-h test periods and compared with simultaneous gravimetric measurements. Both dust monitors responded linearly with mass concentration with both coal dust and ARD. However, the linear response of the PDS-l differed from that of the PCD-l for both dusts.

Jan 1, 1987

By Lars Osen

This investigation was undertaken to contribute to the understanding of underground pull tests by conducting laboratory tests under closely controlled conditions. Steel bolts, instrumented with electrical resistance strain gages, were anchored in an aluminum block, a granite block, and a steel sleeve, and were subjected to pull tests. The bearing plates used were either flat7 dished, or embossed. In pull testing a bolt that is prestressed, there is a range of loading during which bolt load is greater than the jack-applied load, This study showed that preload, the size, shape, and type of bearing plate; and the geometry of the system determine the point at which bolt load and applied load become equal. The effects on bolt load of both a theoretical solution and actual pull tests were analogous and led to similar results.

Jan 1, 1965

By A. V. Hooker, E. J. Coggeshall

"The Bureau of Mines for some time advocated the firing of all blasts in coal mines as single shots, and this method of firing is the general practice in American bituminous-coal mines. All single shots can be fired with permissible single-shot units so designed that they will not ignite mixtures of methane and air.If several shots in a face are fired singly it is necessary to return the face after each shot. In some mines having steeply pitching coal seams, this may be dangerous or even impossible, under these conditions shots are usually fired simultaneously.Several shots cannot be fixed simultaneously with permissible single-shot blasting units, and safe types of multiple shots blasters are not readily available. This means that the firing of multiple shots in gassy mines is usually accompanied by the possibility of gas ignition as the blast occurs.Tests have been made at the Pittsburgh Experiment Station to determine the possibility of developing safe types of multiple-shot units suitable for such use, or of applying other type safely in gassy sections of mines where firing shots singly is impracticable.The tests may be divided into the following four groups:1. Tests to demonstrate hazard in the use of existing types of multiple-shot units of the portable generator type.2. Tests to show the electrical characteristics of multiple-shot generator units relative to the possibility of preventing igniting sparks and of modifying the design and application of such units in furthering safety."

Mar 1, 1935

By V. E. Erwin, W. W. Adams

"INTRODUCTION This report presents statistics of accidents at coke ovens in the United States during the calendar years as 1933, the twenty-first year for which data of this kind are available, 1913 being the first year for which accident reports were collected from the operating companies by the Bureau of Mines. The present report is presented in mimeograph form because insufficient funds are available for printing it. The first report of the Bureau of Mines that contained statistics of accidents for the coke-mining industry in the United States covered the two calendar years, 1913 and 1914. While the figures presented therein related both to beehive and by-product ovens, the original returns from the operating companies were not classified so as to permit the presentation of accident statistics for each class of ovens separately. Beginning with 1915, the accident reports from the operating companies have shown the general type of ovens to which the reports related; therefore, since that year, separate statistics for each of the two classes of ovens have been given in the Bureau's yearly reports of accidents at coke ovens.The coke-making industry in the United States established a safety record in 1933 almost equal in merit to that which it achieved in 1932, when the accident-frequency rate was the lowest and therefore the most favorable that the industry has known. Credit for the achievement is due almost entirely to companies operating byproduct ovens. (See table 8.)"

Mar 1, 1935

By Constantine C. Popoff

During 1946 several high-grade limestone deposits in western Washington were examined by the Federal Bureau of Mines. The purpose of the examinations was to disclose new sources of industrial limestone and to indicate the commercial potentialities of little-known and undeveloped deposits. These examinations were part of a long-range program of investigation of mineral resources of the Pacific Northwest. The following report on the Whitechuck travortine deposit is one of a series prepared in the course of the investigations.

Jan 1, 1949

By Foster Fraas

This Bureau of Mines report describes a method for separating minerals at magnetic susceptibilities within the diamagnetic susceptibility range. The maximum feed rate varies directly with the square root of the lower limit of permissible susceptibility, while the lower limit of permissible susceptibility varies inversely as the square of the magnetic field strength. Minerals may be separated at particle sizes smaller than possible on conventional dry-type magnetic separators.

Jan 1, 1969