Search Documents

By P. D. Kovscek

The performance of a novel prototype kerf-cutting impact mining machine was evaluated under a cooperative agreement between the U.S. Bureau of Mines and RAMEX Systems, Bellevue, WA, while operating under conditions typical of normal tunnel entry development. Selected operating parameters were monitored concurrently to determine baseline operating conditions and to study relationships between operating parameters. Using the data obtained, the specific energy requirements of the impact mining machine were calculated and compared to specific energy requirements of tunnel boring machines cutting in rock having similar hardness. Tests results indicate that the kerf-cutting impact mining machine can provide a mechanical means for mining very hard rock that cannot be effectively mined using commercially available mechanical excavators.

Jan 1, 2010

By Tom Retka

This three volume final report summarizes the activities and conclusions of this contract. The objective of the contract was to develop noise control modifications on a retrofit basis, for auger miner coal-cutting systems. Manuals were prepared to assist mine shop personnel in retrofitting the auger miner with these noise controls. Final Report Volume I - Details all vibration and acoustical tests conducted in develop¬ment of the noise controls. Final Report Volume II - Noise Control Modification Manual for the Jeffrey 100-L Auger Miner describes the various noise control modifications to the auger miner, along with fabrication procedures, cost and vendor information. Final Report Volume III - Noise Control Modification Manual for the Jeffrey 94-L Bridge Conveyor describes the various noise control modifications to the bridge conveyor, along with fabrication procedures, cost and vendor information.

Jan 1, 1978

By R. C. Buehl

An experimental iron blast furnace of 3-foot-diameter hearth, producing about 12 tons of metal per day, was operated for 2 weeks with various proportions of anthracite replacing a corresponding amount of coke. The furnace operated well with anthracite in amounts up to 40 percent of the total fuel and produced metal of uniformly low sulfur and normal silicon contents. An increase to 50 percent anthracite during two attempts resulted in poor operation and the charge hung in the s haft of the furnace. INTRODUCTION Anthracite production in Pennsylvania decreased from 84,400,000 net tons in 1926 to 40,600,000 net tons in 1952, and there was a further decline in 1953 to 30,900,000 net tons. Employment in the anthracite industry dropped from 165,000 men working an average of 244 days per year in 1926 to 57,900 working an average of 163 days per year in 1953,3/ which has naturally resulted in considerable unemployment in the region. The industry is actively engaged in promoting new uses for anthracite to increase the demand and thus improve economic conditions in the region. One possibility is the use of anthracite to replace part of the coke for smelting iron ore in blast furnaces. The tests in this report were made to determine whether this use of anthracite would be feasible.

Jan 1, 1955

By G. W. Grove, H. R. Burdelsky, F. E. Griffith

"INTRODUCTION The work of using a system of air locks in unsealing a mine in Ohio following a fire probably was one of the outstanding jobs of its kind in a medium-thick coal bed.The fire in this mine, thought to have been of electrical origin, was discovered at about 1:30 a.m. on December 11, 1941. Forty-four men were working in the affected section at the time; 5 escaped unassisted, and 37, who had barricaded themselves, were rescued. The bodies of two men, who had succumbed after breathing fumes given off by the fire, were brought part way out of the mine before it became necessary to seal the mine.Direct attempts to extinguish the fire with water were abandoned when hazardous amounts of 'carbon monoxide, methane, and other inflammable gases were detected in return air passing through the main haulageway and escape-way of the mine.The mine was completely sealed on the surface at about 8 p.m. on December 12, 1941, with the two bodies remaining in the mine. Sixteen days after the mine had been sealed, the two bodies were recovered. This was accomplished by air-locking through a partitioned-off stairs compartment of a ventilation shaft. This work was done under adverse barometric and atmospheric conditions.A method for collecting representative air samples from the immediate fire area was used successfully by utilizing a vacuum pump on about 10,000 feet of existing water line that had been broken near the fire area.The immediate fire region was sealed, and confined to a relatively small area; the remainder of the mine was recovered, and operations were resumed February 9, 1942, or 59, days from the time of sealing the mine on the surface. This recovery was made by air-locking the main entries inby from the shaft and No. 2 right-face entries.The distance between air locks averaged about 500 feet, and as each new set of seal stoppings and air locks was completed, the old or outby seals were taken out and the area between was ventilated. In ventilating this area, it was often necessary to use line curtains to direct the air into dead-end places."

Oct 1, 1947

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978

By L. L. Oden

The Bureau of Mines is conducting research to develop methanation catalysts for converting synthesis gas derived from coal to synthetic natural gas. This report describes a method to prepare supported Raney nickel coatings by dipping screen-covered nickel sheet in molten aluminum-nickel alloy. Coatings were formed at 1,050° C that were comparable in thickness, composition, microstructure, and catalytic properties to flame-sprayed commercially pre-pared Raney nickel. A molten salt comprising cryolite-8 wt-pct LiF was employed over the molten metal bath to clean and preheat the substrates, to protect the metal bath from oxidation, and to heattreat the coated specimens. Immediately following heat treatment, specimens were quenched to 700° C in a molten salt bath containing CaC12-34.5 wt-pct NaCl, which also functioned to remove the insoluble occluded fluoride salt.

Jan 1, 1976

By J. C. Hartley

The most important single operation in mining is the ventilation of underground areas in a manner conducive to the health and safety of employees. Adequate volumes of pure air must be supplied at the working faces, along the haulageways, and wherever men work, so as to dilute and carry away the methane liberated from the coal and adjoining strata, noxious gases evolved by the use of explosives, and the carbon dioxide exhaled by men and formed by oxidation of carbonaceous material, as well as any other gases, and also dusts which may be found in mine workings. A sufficient quantity of air must also sweep abandoned or worked-out areas of the mine to prevent the accumulation of gases, where sealing methods are not utilized to isolate old workings. Air, in a quantity adequate to meet the needs of the particular mine to which it is applied, is necessary, and supplying it can be made very expensive through failure to observe good practices in its direction and apportionment." Leaky stoppings, doors, and overcasts rob the working faces of air and add to the ventilating cost by burdening the fans with fugitive air,

Jan 1, 1944

By William M. McKewan

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Ropes of sizes ranging from 3/4 to 2 in. in diameter and from 2 to 35 ft in length were tested to determine their breaking strength, elongation, and torque. This was done to characterize the test equipment on ropes used in mine hoisting systems.

Jan 1, 1990

By F. E. Block, Stephen D. Hill

The necessity for measuring radiation dose is encountered in studying both the beneficial and damaging effects of ionizing radiation on materials . It is also necessary to know the radiation dose absorbed by the reactants in order to evaluate the efficiency of reactions or processes that are promoted by radiation . Thus , a significant effort was made at the Albany cobalt 60 facility to investigate techniques by which the exposure radiation dose can be determined . Methods including ferrous sulfate , ceric sulfate , and methyl methacrylate chemical dosimeters , ion chamber dosimetry , and an absolute radiation calorimeter were investigated . Isodose curves were constructed for several standard source configurations using the dosimetry techniques which were investigated .

Jan 1, 1964

By J. S. Browning

The purpose of this Bureau of Mines project was to develop a method for recovering kyanite and sillimanite from the present zircon-mill tailing of the Jacksonville and Starke, Fla., plants of Humphreys Gold Corp. The kyanite and sillimanite in the ore are not being exploited at present, but procedures for recovering the two minerals were worked out by the Bureau in the interest of conserving natural resources. The current zircon-mill tailing of the Starke plant contains up to 20 percent of a mixture of kyanite and sillimanite. A similar product of the Jacksonville plant contains up to 15 percent kyanite and sillimanite. The average annual production of the tailing now being stockpiled contains several thousand tons of the two minerals. Laboratory batch-flotation tests were made on the materials to determine the feasibility of flotation methods for recovering high-grade concentrates. Various reagents were employed under different conditions to determine the optimum conditions for flotation of kyanite and sillimanite and retardation of the gangue materials. The results of the preliminary flotation tests were encouraging enough to warrant more comprehensive testing of a larger sample of the ore in the laboratory pilot plant.

Jan 1, 1956

By Mah Alla D.

Previously existing heat-of-formation values for the oxides of vanadium were rudimentary. They were subject to uncertainties of 1 to 5 kilocalories per gram-atom of contained oxygen. This fact has been the only adverse influence on the accuracy of thermodynamic calculations involving these substances, as the requisite entropy and high-temperature heat-content data are known with reasonable accuracy. This report presents new heat-of-formation data for four oxides of vanadium (VO, V203, V02, and V205), obtained by combustion calorimetry. It is believed that the uncertainties have been reduced to 0.1 to 0.3 kilocalorie per gram-atom of contained oxygen. The new heat-of-formation data were combined with existing entropy and high-temperature heat-content values to obtain free energies of formation of the four oxides at temperatures up to 2,000° K.

Jan 1, 1961

By D. G. Puglio

This Bureau of Mines study covers 25 underground mines that were active in the Upper and Lower Freeport and Lower Kittanning coalbeds in 1976. The coal ranges from low to medium volatile in rank; its primary use is for steam generation. Seven mines emit more than 100,000 cfd of methane gas; those mines are the deepest and largest producers. The methane gas content of three core samples of the Lower Kittanning coalbed was estimated by the direct method. A sample from a depth of 320 feet contained 0.5 cu cm of gas per gram, at 620 feet there was 0.8 cu cm of gas per gram, and at 1,060 feet there was 11 cu cm of gas per gram. These results suggest that methane control problems will be encountered in the future as deeper coal is mined.

Jan 1, 1979

The Bureau of Mines, U.S. Department of the Interior, devised a flotation technique for upgrading chromite in chromium ores and gravity concentrates. The technique consisted of cationic flotation of chromite from a slime-free pulp acidified to pH 2.5 or lower using H2S04 modifier. Flotation results showed that ore containing serpentine as the primary gangue mineral was more amenable to concentration by this technique than ore containing the readily floatable olivine as the primary gangue mineral. Rougher flotation of a chromite ore containing abundant serpertine increased the grade form 19 to 41 percent Cra03 at a chromite recovery of 89.6 percent. Rougher flotation of ore containing abundant olivine upgraded the chromite from 23.4 to 29.6 percent Cr203 at a recovery of 89.4 percent. The technique was also applied to chromite gravity concentrates to further upgrade chromite and to reject silicates. Flotation of a gravity concentrate containing 40.9 percent Cr203 and 4.4 percent SiO2 recovered 90 percent of the chromite in cleaner products containing 44.9 percent Cr203 and 0.63 percent Si02. The combined recovery by gravity and flotation was 87 percent. An economic evaluation of this technique will be undertaken to deter-mine its feasibility for commercial use.

Jan 1, 1980

By Lung Cheng

Based on earlier tests that showed steel to be much more likely to cause frictional ignition than tungsten carbide, the Bureau of Mines redesigned coal-cutting bits to reduce the hazard of face ignitions. Two bit designs--a mushroom-shaped bit with a conical shank and a dove-tail bit with a rectangular shank--are described, as well as bit wear tests conducted in the laboratory and in an operating coal mine. In laboratory tests, for 1/8-, 1/4-, and 1/2-in-deep cuts and cutting speeds of 280, 500, and 660 ft/min, the mushroom bit had significantly longer tip wear life than the conventional bit; the dovetail bit was also superior to the conventional bit. Results of in-mine tests on the mushroom bit agree well with laboratory results. In-mine tests of the dovetail bit are underway.

Jan 1, 1983

By D. S. Kimmel

The Bureau of Mines sponsored development of a system to remotely energize and de-energize the trolley wire in a section in response to demands from vehicles as they enter and leave the controlled section. The system developed utilizes a detector/actuator that controls a dc contactor at the outby end, and a 3 kHz oscillator at the inby end. A prototype system has been built and installed at the Bureau's trolley test site at Bruceton, Pennsylvania which has demonstrated the ability to also provide load discrimination for faults of 300 amperes or more. The system could readily be modified by locating the oscillator on the vehicle to provide automatic de-energizing of the trolley wire when the vehicle's pole is removed or the vehicle leaves the section.

Jan 1, 1978

By A. G. Smelley

As part of research conducted in its mission to effect pollution abatement, the Bureau of Mines, U. S. Department of the Interior, is developing a dewatering technique that allows for disposal of phosphatic clay wastes, for reuse of water now lost with clays, and for reclamation of mined land. The technique utilizes a high-molecular-weightnonionic polyethylene oxide polymer (PEO) that has the ability to flocculate and dewater phosphatic clay wastes. A synergistic flocculation study was made to determine whether a portion of PEO could be replaced by other reagents. Several groups of reagents were tested: (1) those that increased the zeta potential of the phosphatic clay wastes; (2) those capable of hydrogen bonding; and (3) those which flocculated the phosphatic clay waste. Reduction in PEO consumption occurred only with addition of those reagents able to flocculate the slime. The use of natural guar gums resulted in a lower PEO requirement and also yielded a dewatered product of higher solids content, 43 to 45 percent, versus 33 to 35 percent obtained with PEO alone.

Jan 1, 1980

By H. D. Hess

This report describes in detail a unique occurrence of fersmite, (Ca, Ce, Na) (Cb, Ti, Fe, Al)2 (0, OH, F)6, which occurs as small anhedral inclusions and intergrowths with a tantalum-free columbite found in the metamorphic complexes of Ravalli County, Mont. Chemical and crystallographic data along with the physical and optical properties agree in general with those given in the original description of fersmite from the Ural Mountains of Russia. X-ray diffraction data not given in the original description and more specific optical data have been determined. The Montana fersmite, now established as the second occurrence of this rare calcium-columbate mineral, was discovered during a routine Bureau of Mines mineralogical examination of a prospector's sample.

Jan 1, 1960

By John B. Gayle

[The coking time exerts a Considerable influence on the throughout of a coke oven, and for this reason a large number of papers dealing with the relation between coking tine and the different operating variables have been published. Although all of the factors known to ink influence the coking time have been studied, agreement leas not boon reached on several questions, 3/4/ and it appears worthwhile to evaluate any data that become available during investigations of the carbonizing properties of various oafs and coat blends, this report, therefore, includes a Study of the relation between coking lime and flue temperature and represents the second phase of overall investigation ion of factors influencing the coking time in slot-type ovens.]

Jan 1, 1956

By K. Kar, A. Sreeoath, M. Gautam

"This paper presents results of an experimental investigation of the sampling efficiency of a blunt cylindrical sampler oriented with respect to the oncoming flow. The number of particles sampled by the cylindrical blunt sampler and an isokinetic sampler is measured using the TSI Aerodynamic Particle Sizer. A technique is described to conven the ratio of the particles sampled into the sampling efficiency. The experimental data thus obtained is then compared with the impaction model of Vincent and Mark (1982) with the empirical constant determined from our experiment.. The comparison shows excellent agreement for 0° and 90° orientation.1.0 IntroductionCylindrical dust samplers are widely used in practice to determine the concentration of the airborne particulate matter. The sampler is simply a means to collect particles from the ambient, whose concentration is subsequently measured by some size selective techniques. Gravimetric and optical techniques are the two most commonly used methods to measure the particle sizes. While impactors are used in gravimetric analysis, Aerodynamic Particle Sizer, Aerosizer. Electron microscope, Coulter Counter etc. use the optical method to measure the particle sizes. The Aerodynamic Particle Sizer (APS) and the Aerosizer are the new generation devices which employ the time of flight of particles within intersecting laser beams to determine the particle size.The introduction of the sampler in the free stream disturbs the flow pattern due to two distinct actions of the sampler on the fluid stream: one of them results due to the conformity of the flow to the geometry of the circular cylinder and the second one is caused by the flow into the suction orifice. If the sampler performance is determined by the number of particles entering into the sampler inlet relative to the number of particles present in the free stream, then the particle trajectory outside the sampler and into the inlet is the deterministic factor for the sampling efficiency. The particle trajectory inside the sampler is not important in this case."

Nov 1, 1995

By J. A. Kosek

Work has been carried out under Bureau of Mines Contract HO 395132 to develop improved sensor cells for use in direct-reading detectors and diffusion exposure meters. A pumped CO sensor cell was developed which has a shorter response time, improved temperature cycle characteristics, and improved linearity and stability at high CO concentrations. Diffusion CO sensor cells have shown good response level stability and linearity up to 1000 ppm. In addition, a new sensor cell catalyst has been developed for NO2 sensor cells which has a much shorter response time and improved response stability characteristics.

Jan 1, 1982