Search Documents

By R. V. Ramani, R. Bhaskar

"While the National Academy of Sciences has stated that gravimetric sampling technology for compliance purposes is adequate, research into various aspects of respirable dust control require data on many other parameters of airborne dust. These, in turn, have created the need to use many instruments, other than personal gravimetric samplers, in mi ne environments for dust measurement. There is a need to evaluate the performance of these instruments under conditions of potential use.As part of research in the Generic Technology Center for Respirable Dust, cascade impactors, gravimetric personal samplers and gravimetric samplers collecting dust using isokinetic sampling principles were employed for dust measurements under identical conditions in a mine airway. During the course of the experiments, 8-stage cascade impactors and gravimetric samplers drawing air isokinetically were located in the center of a mine airway at various stations. Two types of data were examined - concentration of dust and size distribution of the dust collected in the samplers. The data show that the amount of dust collected by an impactor is less than half the amount collected isokinetically. The size distributions of the dusts collected from the two instruments, though comparable, show a consistent difference in median diameters. The cause for this bias is examined.The paper presents and discusses the results of the tests, including the concentrations and size distributions obtained from the two instruments for different experimental conditions. There is a need to document the performance of various dust measuring devices in mine airflow conditions.INTRODUCTIONThe sampling of airborne dust in mines can be done for several purposes. Traditionally, dust sampling has been restricted to the gravimetric measurement of airborne respirable dust to comply with the regulations governing the mining industry. Instruments such as the MRE gravimetric sampler, and personal gravimetric samplers that have collection characteristics similar to the human respiratory system have been in use for the last two decades. Presently available instrumentation for the purpose of regulation have been considered adequate by the Committee on the Measurement and Control of Respirable Dust in Mines (National Academy of Sciences, 1980),"

Jan 1, 1989

By William J. Wuest

This U.S. Bureau of Mines report presents an overview of ground control considerations associated with floor heave. Factors affecting heave, such as in situ stress, floor characteristics, and mine geometry, are described. Floor-displacement monitoring and data analysis methods are outlined. Finally, floor heave remediation is discussed. The remedial techniques are divided into four categories: mine maintenance, supplemental support, mine structure, and techniques for multiple-seam operations. Other subjects covered in the report include laboratory and in-place testing of floor rocks, U.S. and international case studies, effects of mine layout, determination of excess horizontal pressure, and types of heave failure. The emphasis of this report is on practical considerations; theoretical discussions are kept to a minimum.

Jan 1, 1992

By John J. Mulligan

The Bureau of Mines investigated reports of mineral deposits within 10 miles of the route of the proposed pipeline from Prudhoe Bay to Valdez. No producing lode deposits or lode prospects of possible national economic significance were found. Measured placer deposits in the route are or slight value except possibly some deeply buried gold placer deposits in the Fairbanks and Livengood Quadrangles. The pipeline corridor crosses five belts of minerals having potential economic value: (1) The north slope of the Brooks Range (oil, gas, oil shale, coal, phosphate); (2) the south slope 01 the Brooks Range (copper, gold); (3) the Livengood area (gold); (4) the Fairbanks area lead-silver, antimony); and (5) the Wrangell Mountains-Denali copper belt (copper-gold). The Jarvis Creek coalfield, an eastern extension of the Nenana coalfield, is on the north side of this belt. Scattered along the corridor across the Chugach Mountain and in the vicinity of Valdez are a wide variety of metallic deposits that make up the eastern margin of the Chugach gold belt but do not seem to constitute a well-defined zone.

Jan 1, 1974

By V. A. Nieberlein

An extractive process was developed applicable to submarginal titanium deposits containing valuable minor constituents; such as columbium (niobium) and iron. The process consisted of reducing the mineral concentrate with coke at high temperature to form a carbide-suboxide sinter, chlorination in the 400° -500° C. range, and fractional condensation of the chlorides. The chlorination procedure recovered 97, 83, and 87 percent of the titanium from brookite, rutile, and ilmenite sinters, respectively, while simultaneous columbium recoveries on the same materials were 85, 50, and 87 percent.

Jan 1, 1957

By A. W. BELDEN

Among the investigations that the Bureau of Mines is conducting witha view to increasing efficiency in the utilization of fuels belonging to or for the use of the Government is an investigation of the processesthat take place in a foundry cupola during a melt. Some observations on the results of cupola tests of cokes at the Government fuel-testing plant in St. Louis, Mo., the coke being fromcoal from many coal fields of the United States, have been stated in a previous bulletin.s Especial attention was given to the meltinglosses that resulted from the use of different grades of coke, light and porous or heavy and dense. These losses amounted in one instance to 52.5 per cent of the iron charged and showed, in convincing manner, the need of exact information in regard to conditions in the fuelbed of the cupola.b Melting losses of iron have been fully appreciated but little under-- stood. The fact that these losses were possible with either light or heavy coke led to the belief that by using small charges 80 placed that. melting would take place in that zone of the cupola where the highest heat and the smallest percentage of oxygen prevailed and by confiningall melting to this zone these losses would be eliminated and the economical use of practically any coke produced for metallurgical purposes would become possible. This widening of the field from whichcoke might be drawn for foundry purposes would serve to place the foundryman in an independent position as regards his source of supply, and would tend to conserve the better grades of coking coals, which are being rapidly exhausted, by making the poorer grades available for mixing with them. In order to investigate conditions within a cupola, the Bureau of Mines as a first step decided to install a commercial cupola, to sample the gases during their travel from the tuy~res upward, and to determine the temperature of the fuel bed.

Jan 1, 1913

By Robert W. Ageton

The Bureau of Mines investigated the in situ vertical component of the rock stress in the rib of the haulage drift on the 6100-level of the Star mine, Burke, Idaho, using the flatjack and borehole deformation methods. The estimate of the vertical component of stress about 2 feet into the rib at a station along the haulage drift on the 6100-level of the Star mine by the flatjack method is approximately 5,875 psi, whereas the borehole deformation procedure at this station yielded a value of 5,500 psi for the same depth into the rib. The test zone is approximately 5,625 feet below the surface.No attempt was made to extrapolate stress estimates beyond the depth of the flatjack installation.

Jan 1, 1967

By R. A. Kearns

To enable the mining industry to be kept informed as to the availability of equipment developed by mining equipment manufacturers in their constant endeavor to keep a step ahead of changes in mining techniques, the Bureau of Mines periodically issues lists of equipment approved subsequent to the last previous listing. The present list covers those approvals issued during calendar years 1953 and 1954. It supplements Bulletin 543, Permissible Mine Equipment Approved to January 1, 1953. The procedure established in Bulletin 543 of numbering items in each category consecutively to indicate the chronological order of the approvals has been continued in this circular. Information on approvals issued later than January 1, 1955 may be obtained by referring to Coal Age, a monthly magazine issued by the McGraw-Hill Publishing Co.

Jan 1, 1955

By R. Stefanko

The industrial hygiene and safety aspects with internal combustion engine in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. Mathematical models of the dilution and dispersion of diesel exhaust contaminants can be useful only if these models can be validated. In this research report, experiments that were specially designed for the above purpose are described. These experiments were conducted in the U.S. Bureau of Mines, Safety Research Coal Mine, in Bruceton, Pa. On the basis of this study, the data collected, and further review of available literature, it is concluded that mathematical models of dilution and dispersion are useful tools for mine ventilation planning. Additional objectives of this study about which conclusions and recommendations are reported here include: (a) evaluation of mine atmosphere contaminant monitoring systems; (b) optimum sampling site locations; (c) model sensitivity and error analyses; (d) computer coding of mathematical models; and (e) development of a diesel bibliography. While an extensive bibliography on diesels is provided in this report, Volume II of this final report has 511 references.

Jan 1, 1977

By Constantine C. Popoff

During 1946 several limestone deposits near Fortson, Snohomish County, Wash., were examined by the Bureau of Mines. These examinations were part of a long-range investigative program of regional mineral supplies required by the anticipated industrial development of the Pacific Northwest. The .study outlined in the following paper was specifically undertaken to disclose new sources of high-purity limestone and to appraise, their economic aspects. The deposits examined -namely the Galbraith, Climax, and Hi, Hi -are somewhat similar in physical features and geologic environment. They are lenticular and belong to the same formation of metamorphosed sediments that underlies the prominent Whitehorse Ridge.

Jan 1, 1949

By R. A. Meyer

A table that greatly simplifies determination of metastable transitions in mass spectra has been prepared. All the mathematically possible metastable transitions of any compound whose molecular weight lies between 26 and 150 can be determined from the table without calculation. The method of utilizing the table is described, using selected peaks from the spectrum of normal butane for illustration. In the mass spectrometer, ions are formed in the isatron and accelerated through a series of slits. Most of these ions reach the collector without further change, but a few dissociate in transit to form new ions. These ions appear in the mass spectrum at neither the mass--to-charge ratio (m/e) of the original ion nor that of the new ion. A formula that relates the appearance of these new ions to the ion from which they were formed is: [ ]

Jan 1, 1957

By L. B. Pankratz

Heat content measurements were conducted for GaPo.996 and InPo.986 over the temperature range from 298° to 1,100° K, and for In2S2.897 over the range from 298° to 1,200° K. Both the actual experimental data and values adjusted to conform with the stoichiometric compositions (GaP, InP, and In2S3) were reported. Entropy increments above 298.15° K were calculated for the stoichiometric compounds, and heat content and heat capacity equations were derived.

Jan 1, 1965

By A. R. Taylor

This report describes the design, construction, and operation of a low temperature adiabatic calorimeter for measuring heat capacities of solids or liquids from 60° to 300° K. A brief discussion of the basic theory involved in chemical thermodynamics and the problems involved in obtaining accurate experimental data is presented. The operation of the calorimeter was tested by measuring the heat capacity of a sample of benzoic acid obtained from the National Bureau of Standards over a temperature range of 60° to 300° K. The measured heat capacity values of the benzoic acid compared favorably with similar values obtained by the Bureau of Standards, the maximum deviation being 0.5 percent. THEORY A brief discussion of the basic theory involved in chemical thermodynamics will illustrate the applications of heat capacity data and the problems involved in obtaining accurate experimental data.

Jan 1, 1962

By Stephen C. Tadolini

The U.S. Bureau of Mines conducted a laboratory investigation designed to evaluate the stress and deformation characteristics of fully grouted roof bolts subjected to various magnitudes of end loadings. The experiment and subsequent analysis were completed, utilizing axial deformation data obtained -ultrasonically from forty-one 4-ft, grade 40 roof bolts, with a total of 132 measurement locations along the lengths of the bolts. The ultrasonic measurement instrumentation used in this investigation allowed for elongation measurements without requiring extensive bolt modifications. The results indicate that approximately 39 pct o{ the applied end load dissipated within the first 3.4 in of the bolts. However, only 3 pct of the applied load was realized beyond 28 in of the grout column. Data are presented individually for every 6-in increment of bolt length, and analysis was performed using statistical, nonlinear equations developed for 5,000 and 8,000 lb loading conditions.

Jan 1, 1990

By Howard E. Rollman

South Central United States, an area including Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas, is a net exporter of refractories. Nearly $45 million of these materials was shipped in 1954 from plants in the area, compared with area consumption of $18.5 million. About 88 percent of all refractories production is concentrated in Missouri. The prevalent consumption pattern, however, is one of localized shortages. For example, although Texas uses more than half of the refractories consumed in the South Central United States, production of refractories in Texas is relatively small. Also, the apparent self-sufficiency of the area is in terms of value produced rather than in terms of products consumed. Nearly all of the $6,425,000 nonclay refractories consumed in the area were shipped from other States. Local resources possibly could be developed for making refractories to serve markets that currently are being supplied from outside the area. Since other industries are growing rapidly in the area, the market for refractories is expected to continue to grow--more rapidly than the national market. The Missouri refractories industry is economically important nationally. Nearly one-fourth of the clay refractories produced in the United States are made in Missouri. Moreover, Missouri produces most of the higher grade clay refractories, about 62 percent of the high-alumina refractories, and 85 percent of the superduty refractories. The competitive position of the Missouri refractories industry is strong. The national market for clay refractories and the market in the South Central United States are expected to continue to grow. The ratio of net income to the value of refractories shipped in Missouri is larger than the national average.

Jan 1, 1960

By L. C. IlsLey

"The maintenance of permissible equipment which is tested and inspected at the Pittsburgh Experiment Station of the United States Bureau of Mines is dependent to a surprisng degree upon the voltage at which the equipment is operated. The difficulty of maintaining 500-volt equipment is frequently brought to the bureau's attention, and it is quite possible that if the bureau had appreciated at the beginning the full hazard involved, it would never have undertaken the approval of equipment operating at voltages greater than 250 volts.In this connection, the following statement from State mine inspection departments and other sources are of interest as showing the general feeling in safety organizations with respect to voltages higher than 250. These statements, although obtained as a result of a questionnaire sent cut several years ago, still apply very well to present conditions.A. I have not had time to consider seriously the proposed change from every angle, but looking at it from a standpoint of hazard, feel that the danger would be greatly increased. I have always occupied the position that underground voltage on portable equipment should never exceed 250 volts.High voltage of course would mean smaller transmission lines, which would be more economical and no doubt would require in several instances smaller equipment; notwithstanding, if this statement is true, the writer is still favorable to low voltage on underground portable equipment.B. I believe 500 volts should be the limit on the best equipment ender the best conditions and that the U. S. Bureau of Mines should do all in its power to limit the voltage to 500 volts on permissible equipment, as any increase in voltage means increased hazard.C. I will refer you to a section of our mining law, entitled ""An Act to Regulate the Tine of Electricity in the Mines of the State of ----"" which reads in part, as follows: Trolley wires, or other exposed electrical wires, shall not carry a voltage above 275 volts.You may readily see by this that we are not permitted to operate mining machines under ground in -----, with more than 275 volts at the terminals, except that we are permitted to install transforming stations throughout the mines, after complying with certain regulations at the mine.However, as we have had to date, within the calendar year of 1925, six men electrocuted in the mines of the State, using a voltage of 275 volts, I am of the opinion that if this voltage was increased, the hazard would also be increased in proportion.D. I do not care to make a statement for publication: however, I am referring you to our mining laws. On page 27 and 28 you will find what the laws of -----¬require relative to the installation of electricity in the mines.""Hereafter where electricity is installed no higher than two hundred seventy-five (275) volts shall be used underground, except for transmission, or for application to transformers or other apparata, where the high-voltage circuit is stationary. High-voltage motors, and transformers, shall be installed in suitable chambers, built of fire-proof construction, and well ventilated, and shall not be placed on intake, or between intake and return air courses. All high-voltage lines lines and apparata must be clearly marked, to indicate their danger. Main and distribution switchboards for high voltage shall be made of insulating and incombustible material, such as marble or slate, and to be free of all metallic veins, or of material equivalent thereto. Same shall be installed in a dry place. All switches or other instruments used in connection with high voltage shall be installed on suitable switchboards, with at least a three-foot passageway in front and rear properly floored, and kept looked by a door at each end that can be opened from the inside without a key. With higher than medium voltage, there shall not be any live metal work on the front of switchboard, and the entry circuit must be protected by an oil breaker s"

Apr 1, 1932

By John C. Machisak

Employment and related injury experience of the coking industry in the United States for 1957 contained in this publication is summarized under three general sections: (A) General injury experience: Tables 1 to 9: Current and comparable statistics on operating data, number, frequency, and degree of severity of injuries and major accident agencies involved in the cause of Injuries. Data are presented for the industry as a whole, for each type of oven, and for the States in which coke was produced.

Jan 1, 1959

By M. P. Youker

USE OF LOW-PRESSURE GAS BURNERS IN OIL- FIELD BOILERS

Feb 1, 1922

By M. Howard Berliner

The Harding pegmatite dike is well known for the production of spodumene and lepidolite in the period 1920 to 1930. It attained greater prominence during the last war by being the largest producer of domestic tantalum ore from the rare mineral microlite. The deposit is believed to be the only proved reserve of tantalum ore in the United States today. In 1943 the main portion of a large tantalum-bearing zone in the Harding dike was developed by the Bureau of Mines with the assistance of the Federal Geological Survey. Analysis of this zone from 39 diamond drill holes and quarry exposures showed a large deposit containing 2 pounds of microlite per ton and 21 percent spodumene, In September 1948, the Bureau of Mines resumed development of the deposit with a view to extending the tantalum-bearing zone farther to the southwest or delimiting the ore body. Seven diamond-drill holes failed to penetrate the ore zone in its southwestward projection, Much of the following general information is summarized from the report on the first exploratory work of the Bureau of Mines by John H. Soule.2/

Jan 1, 1949

By D. C. Crowell

This publication presents the results of a laboratory investigation of displacement of gas by injection or imbibition of water into sandstone models under essentially isobaric conditions. A brief discussion of scaling requirements is included. The influence on residual gas saturation of independently varying the parameters of dimensional ratios of the porous media, rates and methods of flooding, surface tension, initial water saturation, and permeability is shown. Of these variables, increased initial water saturation and decreased surface tension reduced residual gas saturation significantly, whereas variations in flooding rate and dimensional ratios had no apparent effect. No correlation was evident between absolute permeability and residual gas saturation.

Jan 1, 1966

By P. J. Coleman

Research in the field of mining safety and health in the United States plays an important part in protecting the lives of miners. The National Institute for Occupational Safety and Health (NIOSH) Mining Program conducts surveillance, studies and developmental work aimed at improving the safety and health of miners. With recent reviews of the Mining Program by the National Academy of Sciences and the Mining Program response (NIOSH, 2008), the importance of setting goals, conducting high quality engineering and scientific research and evaluating the outputs, outcomes, relevance and impacts of these projects has been reemphasized. Surveillance of reported injuries is a first step in deciding on research directions and in designing specific projects. Groups of injuries often share features and attributes that suggest common causes and may respond to similar preventive efforts. Identifying groups of injuries also serves to prioritize intervention efforts. The Mine Safety and Health Administration (MSHA) Accident and Injury database (MSHA, 2008) provides individual case reports of mining injuries, illnesses and certain no-injury accidents (events such as roof falls that stop mine production or miners? activities for more than one hour). This database is an indispensable resource for researchers and stakeholders needing information on the statistics of these events. From an epidemiological perspective, research projects target groups of miners at risk due to specific patterns of work, equipment, mine settings and the management of safety and health in their mines. Incidence rates are provided by the MSHA data for selected variables, such as surface/underground location, standard industrial classification and state. While incidence rates are the preferred measure for all variables, denominators are not typically available; for example, to more clearly under-stand the data about injury by occupational type, it would be necessary to conduct demographic surveys. A current survey of the demographics of the mining industry should be complete by 2010, which will allow incidence rates to be developed for a number of variables such as age, occupation and experience. This survey will provide the first update of its kind since the first survey was conducted in 1985.

Jan 1, 2010