Search Documents

By Milford L. Skow

Utilization of domestic ores in the winning of metallurgical alumina requires a convenj.ent method of treating siliceous bauxites and other aluminous materials. In the United states there are only small reserves of high-grade bauxite but considerably larger tonnages of low-grade material. In addition, there are large deposits of high-alumina clays. If these high-silica bauxites or high-alumina clays could be beneficiated, either by are dressing or by chemical dissolution to remove a large proportion of the silica, then the potential reserves of aluminum ores would be increased materially. Faced with a similar situation, the German industry, chiefly dependent on high-grade French bauxites prior to World War II, was compelled during the war to Use lower-grade ores. For desilicating the lower-grade bauxites before the Bayer treatment, a method was developed in which the bauxite was calcined and then given a dilute caustic leach preliminary to the pressure digestion. It was planned to regenerate the caustic by treatment of the desilication liquor with lime. As European bauxites are mineralogically different from those found in this country, preliminary work was undertaken to determine whether this process might be applied to domestic materials. The results of this work, along with a review of the German process, are presented in this report.

Jan 1, 1950

By L. J. Kane

Several processes being developed by the Federal Bureau of Mines to provide new and more efficient uses for coal require practical methods for removing dust from hot gases. Filters provide such means. The efficiency of filters made of aluminum silicate fibers and porous stainless steel was determined. The results obtained with the fibers were previously reported.5 In this investigation tests were made with three porosities of stainless steel filter material (grades C, D, and E) at a gas flow of 1,000 std. c.f.h./sq. ft. of filter, temperatures of 75° and 1,000° F., and dust loadings (as represented by cumulative dust fed) of 100, 1,000, and 10,000 gr./sq. ft. of filter. Pressure drop during the runs ranged from 0.1 to 21 in. of mercury, and dust removal from 25 to 99.93 pct. Filters having the finest pores gave the greatest pressure drop and percentage of dust removal; however, their dust-holding capacity was slightly lower. Usually, their ability to remove a higher percentage of dust at the same pressure drop more than compensated for the slightly lower dust-holding capacity. With increase in temperature, for the same weight rate of flow of gas, the pressure drop increased and the percentage of dust removal decreased. The effect of temperature was probably due to the accompanying change in the linear velocity and viscosity of the gas.

Jan 1, 1961

By N. S. Dalal, X. Shi, V. Vallyathan

"Correlated spectroscopic and cytotoxicity measurements were made on newly crushed silica to find whether the fracture-induced, silicon related (Si-0· or Si· type) free radicals play a direct role in the mechanism of hemolysis by silica particles. The free radical content of the silica particles was controlled through the radical decay, thermal annealing, and boiling processes, and was followed with electron spin resonance spectroscopy. Portions of the same sample were evaluated for their hemolytic potential, employing sheep erthyrocyte and optical absorption techniques. The results indicate little, if any, correlation between the amount of the silicon-based radicals and the hemolytic potential of the fresh dusts, but these or related radical sites might be contributors to silica cytoxicity and fibrogenicity via peroxidative pathways .INTRODUCTIONIn an earlier convnunication (1.) from our laboratory it was reported that mechanical crushing of coal and quartz under normal air atmosphere generates free rad;cals on the particle surfaces, and that these radicals decay with time, hence pointing to a higher toxicity of fresh dusts in relationship to pneumoconiosis and silicosis. More recently Fubin; et al.(2) have also reported the detection by electron spin resonance (ESR) of the formation of SiO· and Si·-type of radicals from quartz particles crushed under atmospheric conditions. In agreement with earlier ESR studies on single crystals of quartz crushed under high vacuum (10-10 torr) (3) and subsequent exposure to air (3), and to other gases (4), these radicals were identified (2) as being formed by the hemolytic cleavage of the Si-0-Si bonds and the reactions of the Si· and SiO· ,radical with atmosphere. Fubin; et al. (2) also suggested that these radicals might be involved in the mechanism of the fibrotic action by silica, either by transforming the particle surface into a selective oxidating agent or as an initiator of a sequence of reactions leading to fibrosis. Earlier Gabor and Anea (5) had reported that lipid peroxidation caused by free radicals on the silica surface might be involved in the red blood cell membrane damage. Thus far, however, no parallel cytotoxicity, fibrogenicity, and free radical studies on a given Quartz dust sample have been reported, except for some earlier work from our laboratory (1,6,7). We now present more recent results obtained from parallel cytotoxicity, fibrogenicity, and free radical measurements on a freshly made quartz dust. The dust’s free radical content was measured using ESR spectroscopy while its cytotoxicity poteni1al was estimated via hemolysis. Hemolysis was employed as the tox1c1ty test because it 1s a widely used method for estimating the potential of a dust for disrupting the cell membrane (8). The f1brotic potential was followed.by measuring the dust-induced lipid perox1dat1on. us1ng linole1c ac1d as a model lipid. As discussed below, the results obtained suggest new clues.to the mechanism of the Quartz-related cytotoxicity and fibrogenicity."

Jan 1, 1988

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow, S. T. Bagley

"Permissible exposure limits (PELs) have been established for gaseous pollutants, carbon monoxide (CO), carbon dioxide (CO), nitric oxide (NO), nitrogen dioxide (NO2), and some gas-phase hydrocarbons emitted in diesel exhaust. There is, as yet, no PEL recommended for diesel exhaust aerosol (DEA), nor is there a standard method for sampling this aerosol.The University of Minnesota and the U.S. Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size-selective inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were made in underground coal mines that use diesel equipment.The mine mean DEA concentrations for the five mines surveyed, determined with the PDEAS in the haulageway, was 0.89 mg/m3, with a standard deviation of 0.44 mg/m3. DEA contributed 52 % of the respirable aerosol at this location.In three of the mines filter samples were collected for DEA-associated polynuclear aromatic hydrocarbons (PAHs) and biological activity determinations. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust. In general, the PAH and biological activity levels were similar for all three mines, and indicate that up to 25 % of the haulageway concentrations may be contributed by outby diesel vehicles. Measured concentrations of CO, CO2. NO, NO2, and SO2, were well below regulated levels.INTRODUCTIONDiesel exhaust contains pollutant gases, such as carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and gas-phase hydrocarbons, as well as DEA. Much of the health-related concern focuses on DEA and associated organic compounds (Watts, 1992a). A wide variety of these PAHs have been identified and some are known carcinogens and/or mutagens. The U.S. Mine Safety and Health Administration (MSHA) has proposed new PELs for these and other contaminants (MSHA, 1989). MSHA has also published an advance notice of proposed rulemaking to establish a separate PEL for diesel particulate (MSHA, 1992)."

Nov 1, 1995

By Christopher C. Jobes, Alan G. Mayton, Farid Amirouche

Based on prior mine vehicle studies of operators’ exposure to whole-body vibration, researchers from the National Institute for Occupational Safety and Health (NIOSH) evaluated four seat designs on mine haulage vehicles, with regard to roadway-induced jarring/jolting and operator comfort. Investigators collected objective and subjective data from vehicle operators on two existing and two NIOSH seat designs. This study included time and frequency response data using accelerometers and a data recorder, operator perceptions of jarring/jolting and discomfort levels using a linear visual analogue scale, and data from a questionnaire developed for this study. Results from the analysis of subjective data show that operators generally favoured the NIOSH-designed seats over the existing seats. The results of analyses from the absorbed power method and the threshold limit method, based on ISO 2631-1 (ISO, 1985), support the premise that NIOSH seat designs are superior to the existing vehicle seat designs on both models of mine shuttle cars used in the study. The NIOSH seat designs, featuring viscoelastic foam padding, were more effective in reducing vibration energy for operators exposed to vehicle jarring/jolting. In this paper, the performances of the NIOSH and existing seat designs are compared relative to the operator’s exposure to vehicle vibration (mainly jarring/jolting).

By H. E. Powell

Magnetic susceptibilities were determined by the Bureau of Mines fur 19 cobalt- and nickel-bearing minerals and for a suite for synthetic cobalt-nickel diarsenides analogous to the rammelsbergite and safflorite series. Relations between susceptibility and composition were found to be nonlinear for both impure natural minerals and pure synthetics.

Jan 1, 1967

By Henry E. Perlee

Air compressor explosions that are caused by the ignition of combustible vapor mixtures cannot be explained by a single reaction mechanism or sequence of events. Explosions have been caused by the sudden release of large quantities of lubricating oil, by the rapid vaporization of oil that had accumulated slowly in high-pressure piping, and by the production of decomposition products from carbonaceous deposits. Ignitions can be caused by the heat produced in a catalytic reaction, in a compression process, or when a shock wave is propagated through a combustible vapor-air mixture. The frequency of these ignitions can be minimized by establishing proper maintenance and cleaning schedules. Further study is needed to satisfactorily correlate the various factors involved in compressor explosions.

Jan 1, 1963

By R. A. Guereco

Accurate measurements of physical dimensions of a section of stainless steel capillary tubing are presented and used to develop two final working equations for an absolute gas viscosimeter. The effects of pressure and temperature on these dimensions are considered. The internal surface finish and nonuniformity of the capillary bore are discussed, as well as entrance, kinetic energy, gas slippage, and gas compressibility correction factors.

Jan 1, 1967

By E. P. Youngman

The basic mining law of Netherland India is contained in N. I. Statute 1899 , No. 214 , as amended by N. I. Statute 1910 , No. 588 , and 1919 , No. 4 , which is quoted as the " Indian Mining Law, " the effective date of which was fixed as May 8 , 1907 , by proclamation dated October 12 , 1906. The Indian Mining Law was supplemented by Ordinance No. 38 , of 1930 , which was passed by the Volksraad on March 18 , 1930 , to become effective on October 1 , 1930 ( superseding an earlier ordinance entitled " Government Gazette , " 1906 , No. 434) . An important law with respect to American petroleum rights , Statute No. 23 , passed February 9 , 1928 , approving contracts between the Indian Government and the Netherland subsidiary of a large American oil company , is in the nature of a private law or of an enabling act ( see section of this paper entitled " Rights of Foreigners" ) . Statute 1930 , No. 348 , effective October 1 , 1930 , sets forth in minute detail conditions under which prospecting and mining permits may be granted. Statute 1930 , No. 341 , effective October 1 , 1930 , embodies the police regulations of the mining industry.

Jun 1, 1931

By D. K. Deardorff

The hafnium-vanadium phase diagram was constructed within an estimated accuracy of ± 10° C and ± 2 wt pct composition. Alloys for investigation were melted under an atmosphere of purified helium by nonconsumable tungsten-electrode arc melting on a water-cooled copper hearth. Melting points were determined by optical pyrometer, and the remaining phase relationships were investigated by metallography, thermal analysis, and X-ray diffraction. The existence of a face-centered cubic intermetallic compound HfV2 (a = 7.38 A) was confirmed. A eutectic reaction occurred at 20 wt pct vanadium and 1,395° C to yield HfV2 and 8 solid solution. HfV2 melted incongruently by a peritectic reaction at 1,480° C, and the 3 solid solution decomposed eutectoidally at 1,165° C and 6 wt pct vanadium to yield HfV2 and a solid solution. The eutectoid, the eutectic, and the peritectic isotherms extended from 1 to 36.3 wt pct vanadium, from 8 to 36.3 wt pct vanadium, and from 26 to 89.5 wt pct vanadium, respectively. Terminal solid solubilities of hafnium in vanadium at 1,300° C and of vanadium in hafnium at 1,100° C determined to be about 3 and 1 wt pct, respectively.

Jan 1, 1965

By Perry G. Cotter

The borides of the transition metals in Groups IV and VI exhibit, in addition to a certain degree of hardness, considerable resistance to heat and oxidation. They have high melting points (1,850°-3,060° C.) and low coefftcients of thermal expansion and can be bonded with other materials and hot-pressed to desired shape (cermets). Suggested uses for the borides include use in rockets and jet engines, as thermocouple protection tubes, as containers for molten metals in die casting, as flame-plated coatings on less refractory compositions to prevent erosion by hot gases, and as control rods and neutron shielding material in nuclear engineering, The Federal Bureau of Mines investigation of zirconium diboride started in 1950 at the Boulder City Nev,, Metallurgy Research Laboratory, Its purpose was to reduce the cost of raw materials for the production of zirconium diboride.

Jan 1, 1961

By D. J. Donaven, Manuel Gomez, W. S. Landers

Bulk density tests were made on a Western U.S. coke oven plant blend to obtain bulk density control data that would be directly transferable to plant practice . Maximum bulk density values were obtained at zero surface moisture . Increase in surface moisture to about 6 percent decreased the bulk density to a minimum value . Increase in the fine grinding of the blend , at constant surface moisture , decreased the bulk density . The effect of oil on bulk density was observed with five oils at concentrations ranging from 1/8 to 1-1 / 2 gallons per ton . Maximum bulk densities were obtained within the 1 / 2- to 1 - gallon - per - ton range . Essentially the same bulk densities were obtained with petrolatum- and nonpetrolatum- containing oils . Storage effects were observed on samples tested at selected intervals from 0 to 56 days . No significant change in bulk density took place if no surface moisture was lost during storage .

Jan 1, 1964

By J. A. Herdlick

"INTRODUCTION The BeVan quartz crystal prospect in the Indian Creek mining district of Lemhi County, west-central Idaho, was examined by an engineer of the Bureau of Mines 3/ on July 9, 1943. As quartz crystals possessing peizoelectric properties were on the critical list of strategic war minerals, further exploration of the deposit was recommended. The Bureau of Mines exploration began in December 1943 and continued through January 1944. Additional trenching was completed during May and June 1944. This report presents the data obtained by this exploration.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual exploratoiy work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyses samples and makes beneficiation tests.The quartz crystals found during the exploration were examined and classified at the Bureau of Mines College Park, Md., laboratory and checked at the National Bureau of Standards, Washington, D. C.Fred BeVan, of North Fork, Idaho, and Edward F. Cenis, of the Montana Coal & Iron Company, Spoane, Wash., provided much information on the history and past production of the property."

Mar 1, 1948

By A. S. Swanson

In view of the necessity or increasing production of metallurgical fluorspar to satisfy wartime demands, 0, M. Bishop, former district engineer of the Bureau of Mines, L. W. Carrier and. J. S. Williams, senior geologist of the Federal Geological Survey, and E. H. Dawson, mining engineer of the War Production Board made a joint survey of the Illinois-Kentucky fluorite district in July 1942 to determine what steps should be taken to increase production. As part of their recommendations, a program for exploring the idle Klondike mine in Livingston County, Ky., was outlined. All the ore produced at the Klondike mine was mined above the 325-foot level, where some tonnage remains. Factors that influenced selection of the Klondike mine for exploration were favorable geological conditions, the state of mine development and the availability of pumping equipment and some usable mine and mill equipment. In December 1942, the Metals Reserve Co. leased the Klondike mine from the Salem Fluorspar Co.

Jan 1, 1949

By Frank K. McIntosh

The Hamme tungsten district is in Vance County, N. C., and Mecklenburg County, Va. Principal development has been in Vance County. The district is approximately 8 miles long by 1 mile wide and extends northeast-southwest. Its center is about 3 miles N. 65° W. of Townsville, N. C. The occurrence of tungsten in the district was first reported in 1901, but it was not until the Hamme brothers revived interest in the deposits in 1942 that commercial development began. The Bureau of Mines, as part of the war minerals program, began exploration and development of the district in June 1943 and completed it in December 1943. The Federal Geological Survey cooperated by mapping the topography and geology and logging the drill cores. The program included mapping, trenching, sampling, diamond drilling, and analyses and beneficiation of ore samples, The principal ore mineral is hubnerite, which occurs in quartz veins within the schist and granite. The veins are generally lenticular along the strike and dip. About 50 quartz veins have been noted in the area, but many are barren or slightly mineralized.

Jan 1, 1948

By Welby Courtney

Because of the inherent safety problem associated with the deposition of airborne respirable dust onto the floor and other airway surfaces, the Bureau of Mines investigated the rate of reduction of airborne respirable dust in an airway due to deposition of the particles onto the surfaces of the airway. The effects of relative humidity and air velocity on the deposition rate were examined. It was found that the deposition rate was comparable in magnitude with the Stokes sedimentation rate and that it was independent of relative humidity. However, near the dust source the deposition rate depended significantly upon the air velocity, with such dependence decreasing with increasing distance from the dust source. In addition, the size distribution of the airborne particles was approximately constant along the first 300 ft of the airway, indicating that it was not merely the larger (heavier) particles that were being deposited. These results suggest that deposition, though comparable with the Stokes sedimentation rate in magnitude, does not follow a simple Stokes-type process, and that the process of deposition remains to be explained.

Jan 1, 1986

By Albert L. Toenges, Theodore R. Jolley

"The development of Alaska depends on the existence of an adequate fuel supply in the Territory. The need to investigate coal deposits was recognized as early as 1911, when the first investigations were conducted in Alaska by engineers of the Bureau of Mines.Conditions existing in the Bering River and Matanuska coal fields, as found by Dr. Robert A. Holmes, former Director of the Bureau of Mines, are described by the Honorable W. L. Fisher, former Secretary of the Interior.4/Following Dr. Holmes' investigation, a party of Bureau of Mines engineers headed by R. Y. Williams visited the Bering River field in 1912 in cooperation with the Navy Department. A detailed examination was made of the Bering River field, and 855 tons of coal were mined from three prospects on Trout Creek. This bulk sample was delivered to the Navy for steaming and other tests. A description of the work of the field party and results of tests of the coal by the Navy Department and the Bureau of Mines has been published.During 1920 to 1922, the comparative steaming properties of Alaska bituminous coal, lignite, and wood were determined by the Bureau of Mines.6/In the early 1920's, the Bureau of Mines established a coal laboratory at Anchorage, where Alaska coals were analyzed. Subsequently, this laboratory was transferred to the Alaska Railroad and was used by the railroad for coal and other tests.Since 1910, the Bureau of Mines has made analyses of coal from Alaska, and the results of these analyses have been published.7/ The coal analyzed was obtained from mines, tipples, delivered lots, and face samples of coal deposits, and these samples were obtained in the field by engineers of the Bureau of Mines and geologists of the U. S. Geological Survey.Because of the shortage of petroleum and petroleum products in Alaska during the war, low-temperature carbonization assays of coals from the Broad Pass, Forty-Mile, Matanuska, and Nenana fields were made by the Bureau of Mines, and the results were published.Coal beds in the Matanuska field contain interbedded impurities in the form of shale, clay, and bone. The coal should be cleaned mechanically to obtain a satisfactory fuel. A coal-preparation study of bituminous coal from the Eska and Evan Jones mines was made by engineers of the Bureau of Mines, and the results were published.9/Coal production in Alaska is less than the requirements, and coal is imported to make up the deficiency. The cost of this imported coal is high. Greater production is necessary to supply coal for Army installations, industry, and homes. At present, there is only one bituminous coal mine (Evan Jones) in Alaska. The output of this mine is used at Fort Richardson, Anchorage, and by the Alaska Railroad. The economic life of this mine is limited (reported to be 3 years), and its closing, because of accidents or exhaustion, will cause great hardship to the inhabitants of Alaska. There is need to develop new, modern mines for the production of bituminous coal in the Matanuska field."

May 1, 1949

By Charles Vaught, Jeff Duncan, Michael J. Brnich, Lisa J. Steiner

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.3 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Remote control and extended cut miner operators and face crews Length: Eight questions (30 minutes for administration plus 30 for discussion) Skills: Remote control mining procedures including remote control mining, taking extended cuts, resetting breaker on mining machine, and setting timbers. Communicating mine conditions, influencing safe behaviors when mine conditions are less than stable Location: Underground coal mine, four section continuous mining operation Average seam height is 48 inches Problem: Your regular job is on the general labor crew at Cripple Creek #9 mine, a four section continuous mining operation. The mains are 9 entries wide and panels are 5 entries across. You and the rest of the crew had annual refresher training about 3 months ago. For the past few days you have been sent to 2 South panel to fill in as the third shuttle car operator. This morning, however, your buggy is down. The face boss asks you to get the scoop and take seven or eight timbers to the number 5 entry because the last shift got off sight line. The miner will be working in entry 5 while the bolter crew pins entry 4. When you get up to the face you see that Mo, the remote control continuous miner operator, has rounded off the left inby corner in order to make his first cuts in the right hand rib. Now, he has squared around enough so that you and Red, the miner helper, can set some posts on the corner. The two of you set posts along the left inby rib of #5 entry while the shuttle car operator waits. You are in a tight spot when Mo decides to start mining. You must decide where the best place is to stand for safety and to be out of the way.

Jan 10, 1999

By E. R. Palowitch

This report stems from a study by the Bureau of Mines of the possibility of reducing coal filter-cake moisture by applying radiant heat directly to the filter cake while under vacuum during the drying phase of the filter cycle. One disk of a 4-foot-diameter vacuum filter was equipped with gas-fired radiant-heat generators and the effect of radiant heating on the moisture content of a variety of filter cakes was studied. The results of this investigation show that this process can best be described as a filter aid capable of increasing the effectiveness of conventional filtration approximately 6 percentage points of moisture. The operating cost of removing water by this method is somewhat lower than the average operating cost of thermal drying and is considerably cheaper when the total cost is considered. Removal of water from coal that has been wet-cleaned is an important part of the overall coal preparation process. Water is a contaminant, and it is foolish to wash coal to reduce its ash content and add inert water in the process. In some instances the removal of water is actually more important than the removal of ash-forming minerals; its weight adds to the cost of transportation, and its evaporation during burning or carbonizing absorbs useful heat. Fine coal that contains more than about 10 percent moisture is notoriously difficult to handle. A problem thus exists for which there are sound practical and economic reasons to seek a solution.

Jan 1, 1961

By R. D. Berkenkotter

This report describes a weighted method for evaluating the mean and variance of assay data from samples of different length . The method , which produces unbiased estimates from which valid confidence limits can be computed , is appropriate for bedded deposits of variable bed thickness and for vein deposits of variable vein width . Assay data from the bedded Florida phosphate deposit is used to illustrate the procedure .

Jan 1, 1964