Search Documents

By Alla D. Mah

Heat content and entropy data at high temperatures were obtained for cuprous oxide (Cu2O) and cupric oxide (CuO). Experimental results and smooth values are reported. Equations are given for heat content increments and heat capacities above 2980 K. Low-temperature heat capacity data were obtained for cuprous oxide. Evaluation of the 2980 K entropy gave, S°298.15(Cu2O) = 22.08 ± 0.10 cal/deg mole. Heat of formation values were determined for cuprous and cupric oxides. The values are: AH°298.15(Cu2O) = -40,830 ± 300 cal/mole, and AH°298.15(CuO) = -37,230 ± 150 cal/mole.

Jan 1, 1967

By J. E. Tress

The Bureau of Mines has developed a process to utilize waste heat from electric arc steelmaking furnace gases to preheat the ferrous material charged to the furnace. Four heat exchangers were designed, tested, and operated successfully on 1-ton electric arc furnaces. Briquets and pellets were charged continuously, both countercurrent to the hot furnace offgasses and at ambient temperatures. A comparison of the electrical energy consumed in each situation showed that preheating can lower energy requirements as much as 15.6 percent.

Jan 1, 1975

By M. M. Fine

"Button" type ore from the Cason mine, Batesville, Ark., can be up-graded to plus-40-percent manganese by mineral-dressing procedures. A simple process including gravity concentration and. magnetic separation yielded more than 50-percent recovery of concentrates containing 38.1 to 40.6 percent manganese. These values in turn could be raised to 41.4 and 42.8 percent, respectively, upon sintering to conform to size specifications. The Bureau of Mines in the past has surveyed and tested many manganese ores and prospects in an endeavor to alleviate the shortage of manganese. The present period of emergency again emphasizes the strategic position of the metal, and manganese investigative work is being stressed to find new ore bodies and to apply newer beneficiation techniques to the known deposits.

Jan 1, 1953

By H. P. Holmes

Tonnage quantities of hafnium metal have been prepared in Kroll-process equipment designed for producing zirconium. Some slight process modifications have been necessary, but overall operation is the same as for zirconium. Hafnium oxide is chlorinated in the presence of carbon and the resultant hafnium tetrachloride reduced by magnesium metal. Byproduct magnesium chloride is removed in a high-vacuum distillation step and the hafnium sponge metal crushed for further use. Arc-melted metal can be forged and rolled to sheet, but the best material produced to date would not be considered cold ductile. INTRODUCTION This investigation is part of the program for the production of pure metals from domestic and foreign ores that has been underway at the Bureau of Mines for several years. It was done in cooperation with the Atomic Energy Commission and the Bureau of Ships.

Jan 1, 1955

By J. J. Drost

The feasibility of basic oxygen furnace (BOF) offgas heat recuperation by preheating scrap was investigated on a pilot plant scale by the Bureau of Mines. In this study, offgases generated during the oxygen blowing of a molten pig iron and scrap charge were passed through a static bed of shredded auto scrap. Scrap quantities varying from 100 to 180 pounds and representing from 22 to 40 percent of the 450-pound BOF metallic charge were preheated in this manner. Average scrap bed temperatures of 1,650° F for 100 pounds of scrap and 1,150° F for 180 pounds of scrap have been achieved during the blows. As compared to cold scrap used in the normal BOF practice, it was found that by preheating scrap, usage could be increased by 43 percent. The thermal energy recovered by this preheating method can account for up to 44 percent of the energy necessary to melt the scrap.

Jan 1, 1974

By Elton L. Litchfield

The techniques for direct initiation of detonation, developed by the Bureau of Mines, have been applied to gaseous mixtures of oxygen with methane, 'thane, propane, butane, or hexane. An exploding wire was used as the initiation source to determine minimum stored electrical energies required to effect detonation of mixtures between one-half and two times the stoichiometric fuel ratios. Detonations were obtained in the most easily initiated mixtures of ethane, propane, butane, and hexane for initiation energies between 24 and 33 joules at 1 atm and 28-43 joules at 0.5 atm initial pressure. Methane mixtures, at 1 atm, were not observed to detonate when initiated with up to 484 joules.

Jan 1, 1966

By C. W. Vierrether

Tailings from the Pea Ridge iron mine contain significant amounts of apatite, which has rare-earth element values associated with it. In association with the recovery of rare-earth minerals as a secondary resource, the U.S. Bureau of Mines conducted an investigation on the recover ability of the rare-earth minerals from these tailings. The mill tailings were subjected to a phosphate flotation to separate the apatite from other constituents. More than 70-pct recovery of the rare-earth values was achieved. Based on mineralogical characterization and prior analysis of rare-earth-bearing breccia pipe material at Pea Ridge, it is proposed that processing this phosphate concentrate on a vanner table would yield up to a 95-pct recovery of the rare earths in the concentrate, with the apatite reporting to the tailings. Intensive ore microscopy studies of the original tailings to the flotation products led to the identification of monazite, xenotime, and rare-earth-enriched apatite as the major rare-earth-bearing minerals in the tailings.

Jan 1, 2010

By G. R. Hopkins, E. M. SEELEY

According to reports received by the Bureau of Mines, Department of Commerce, as of Jamary 1, 1930, there were 1,035 natural-gasoline plants in the United States, with a total daily capacity of 10,516,000 gallons. (These data do not include one small plant in Alaska.) The last similar survey, that of Jamary 1, 1928, showed a total of 1,155 plants of 8,048,000 gallons daily capa- city. This in two years time the number of plants has decreased by 120, but the total capacity has increased 2,468,000 gallons or 31 per cent. This is roughly equivalent to the gain in production over the same periodi Over half of the increase in total capacity was registered in California, where the development of flush oil production having a comparatively high gas-oil ratio in such fields as Santa Fe Springs led to construction of some new plants and material enlargement of others. Of the total plants, 999 were operating on Jamary 1, 1930, and 36 were shut down. This compares with 1,060 operating and 95 shut down two years ago, which indicates a tendency to dismantle plants as soon as they become obsolete or umrofitable. The total daily capacity of the plants operating on Jamiary 1, 1930, amounted to 10,278,000 gallons, or 98 per cent of the total, leaving only 238,000 gallons, or 2 per cent, for the shut-down plants. This contrasts with the refining industry, which usually has 5 per cent of its total capacity idle; the difference is due to the relative ease with which a refiner can secure a crude supply as against the difficulty the natural gasoline manufacturer has in reestablishing his gas connections. During 1929 the average total daily capacity of the operating plants was 9,899,000 gallons, while the average daily production amounted to 6,015,000 gallons. This indicates that the plants operated during 1929 at 61 per cent of their capacity. Although over 60 plants were dismantled in Oklahoma during 1929 the State continued to rank first in total mumber. California was second in mumber of plants with 165, and was one of the few States that showed a gain since the

Jul 1, 1930

By N. S. Dalal, X. Shi

"With a view of elucidating the role of glutathione (GSH) in the biochemical pathways of the chromate-exposure related carcinogenesis, we carried out electron spin resonance (ESR) spectroscopic investigations of the chromate-GSH redox reactions. The ESR measurements, employing spin-traps, provide evidence for the involvement of the glutathione (GS•) radical, as well as an isolable Cr(V)-glutathione intermediate. These results indicater a new mechanism for the reduction of chromate by GSH in cellular environment and help understand the (unexpected increase in Cr(VI)-induced DNA strand breaks at elevated GSH levels.We report here indirect electron spin resonance (EGR evidence for the involvement of the glutathionyl (GS) radical and direct evidence for a Cr(V) intermediate in the reactions of glutathione ¬(GSH) with chromate for the first time.. This work was undertaken to clarify the biochemical pathway of the reduction of chromate by GSH, since this reduction process is thought to be a critical step in the pathogenesis of the chromate-exposure related carcinogenesis. This follows from the literature reports which show that (a) Cr(VI)compounds have been proven to be carcinogens in laboratory animals as well as in human studies2-4, (b) Cr(VI) and not Cr(III) compounds are mutagenic 5-7, (c) Cr(VI) and not Cr(III) compounds can penetrate cell membranes 8.9 (d) the final state of Cr(VI) in cellular reductions is Cr(III)', (e) by itself chromate (or Cr(VI)) cannot be directly mutagenic since Cr(VI) is known not to interact with isolated DNA under physiological conditions 10, suggesting the significance of Cr(VI).reduction processes. One of the major reductants in cellular environments is thought to be the GSH, both outside and inside the ce11s 11-13. Other evidence for the role of GSH in the chromate toxicity is seen from recent studies showing that exposure of hamster cells to non-toxic levels of added selenite increases the levels' of GSH as well as the Cr(VI)-induced DNA strand beaks 14, and thatsuch DNA strand breaks in hepatocytes also change in direct proportion to their GSH content 15,16. These observations wereinterpreted as implying that the reduction of chromate by GSH, to some reactive intermediate is an important step in the chromatecarcinogenicity 15,16. The following reaction steps were,suggested 15, 16"

Jan 1, 1988

By Graham W. Marks, Clyde A. Bridger

"INTRODUCTION An electrolytic process for the preparation of metallic cobalt has been developed recently in the Bureau of Mines Experimental Station at Boulder City, Nev. Chemical analysis shows this cobalt to contain impurities in small percentages, chief of which is nickel. It is desirable to be able to determine these impurities spectrographically. This report is concerned with a procedure for the spectrochemical determination of nickel in cobalt.Previous spectrographic work on cobalt was done by Breckpot and Mevis,/ who used the method of homologous pairs of lines. However, it was felt that a more detailed investigation was needed, employing the method of internal standards.ACKNOWLEDGMENTWe are indebted to B. G. Knickerbockor and his staff at the Boulder City, Nev., station of the Federal Bureau of Mines for their cooperation, and particularly to Richard W. Lewis and Robert G. Sanderson, who prepared nickel-free electrolytic cobalt for us."

Feb 1, 1948

By Charles K. Rose

The Cebolla Creek titaniferous iron deposits near Powderhorn in southern Gunnison County, Colo., were examined by the Federal Bureau of Mines as part of an overall program to investigate the Nation's titanium and iron resources. The deposits occur around the periphery of the Iron Hill stock, which underlies an area of about 12 square miles. Concentrations of magnetite, ilmenite, and perovskite arc localized along fractures in the pyroxenite stock. Mineralogical studies of composite surface samples collected in 1956 showed that most of the iron is present in ilmenite-bearing magnetite. Perovskite is the chief titanium mineral in the magnetite-rich and augite-rich types, and sphene is the principal titanium mineral in the placer material. The mica-rich rock contains approximately equal amounts of perovskite, ilmenite, and sphene.

Jan 1, 1960

By Alexander May

The U.S. Bureau of Mines conducted studies to determine if phosphate slag stockpiles at Tennessee Valley Authority's National Fertilizer Development Center were hazardous materials. The stockpiles were not hazardous materials as determined by Environmental Protection Agency (EPA) extraction procedure (EP) toxicity test. Radium-226 concentration was 28.7 pCi/g in slag and 2.1 pCi/g in background material. Radium-226 was not leached from the slag. Fluoride concentration was 3.87 pct in slag, 0.18 pct in subsurface material under slag, and 0.08 pct in the background. Slag material permeability was 1.65 x 10-3 cm/s, and subsurface material permeability was 3.24 x 10-6 cm/s. Rain water, trapped in a depression on top of the east slag stockpile, became seepage water at the base of the stockpile. Concentrations of EPA toxic elements in seepage water were much less than concentrations from an EPA EP toxicity test on the slag. Twelve elements-Na, Mg, Ca, Sr, Ba, Cr, Mn, Co, Cu, Cd, AI, and P-had higher concentrations in seepage water than in rain water on top of the slag stockpiles, or in creek water adjacent to stockpile bases, indicating that they were leached from slag stockpiles.

Jan 1, 1990

By Guy A. Johnson

To improve productivity and cut costs, modern underground mining operations have become more mechanized. This mechanization has increased the usage of fuels, hydraulics, and electrical equipment associated with diesel-powered vehicles, thereby also increasing the hazards of underground mine fires. The Bureau of Mines evaluated the fire hazard problem and assembled prototype components for a system that would automatically sense and extinguish fires on mobile underground equipment. The prototype system and alternative designs were in-mine-tested and proved effective. This report summarizes this technology, which can cost effectively help solve the problem of fire hazards on underground vehicles.

Jan 1, 1983

By Agnes Y. Lee

The Bureau of Mines has developed an effective hydrometallurgical method to recover high-purity Pb metal and elemental S from concentrates. This low-temperature process eliminates S gases and Pb emissions, in contrast to the current high-temperature smelting technology. The method consists of (1) oxidative leaching with H202, Pb02, and waste fluosilicic acid at 95° C to produce a solution of PbSiF6 and a residue containing elemental S, (2) electrowinning the PbSiF6 solution at 35° C to produce 99.99 pct Pb metal and H2SiF6, and (3) solvent extraction to recover S, leaving a residue containing Cu, Ag, and other metal values. Spent electrolyte was recycled repeatedly, with impurity buildup controlled by controlling the leach parameters.

Jan 1, 1986

By Rolf S. Paine

The Bureau of Mines studied the presplitting technique used for control-ling overbreakage in the walls of a vertical shaft at the U.S. Army Corps of Engineers Littleville Dam project near Huntington, Mass. The periphery of the shaft, the dimensions of which were 16-1/2 feet wide by 21 feet long and 52 feet deep, was presplit (cracked) in the solid to a depth of 48 feet prior to full-depth sinking. Presplitting prevented overbreak in a fairly soft schist and provided sound self-supporting walls which required very little scaling.

Jan 1, 1965

By Rolf S. Paine

The Bureau of Mines studied the presplitting technique used for control-ling overbreakage in the walls of a vertical shaft at the U.S. Army Corps of Engineers Littleville Dam project near Huntington, Mass. The periphery of the shaft, the dimensions of which were 16-1/2 feet wide by 21 feet long and 52 feet deep, was presplit (cracked) in the solid to a depth of 48 feet prior to full-depth sinking. Presplitting prevented overbreak in a fairly soft schist and provided sound self-supporting walls which required very little scaling.

Jan 1, 1965

By Robert J. Hundhausen, GEORGE M. GRISMER

This circular describes the methods and costs of deepening the Silver Summit three-compartment shaft in the Coeur d'Alene mining region of Idaho. A noteworthy rate of advance was achieved at this operation by the successful use of a mechanical shaft-mucking machine. The Silver Summit mine is 1 mile west from the town of Osburn, Idaho, via U. S. Highway 10. The adit-level portal of the mine is on the south slope of the Coeur d'Alene River Valley at an altitude of 2,700 feet. The Silver Summit shaft is 6,000 feet from the portal. In past years this shaft had been sunk from the adit level to a depth of 1,500 feet. During 1946 the Polaris Mining Co, deepened it to 3,095 feet. The work was done under a co- operative development agreement between the Silver Summit Mining Co. and the Polaris Mining Co.

Jan 1, 1948

By Richard L. Rains

In 1992, the Bureau of Mines evaluated mineral resources of the 34,043-hectare Caribou City and 41,943-hectare Stump Creek study areas in southeastern Idaho. No resources were delineated. The areas had been proposed for wilderness. Rocks underlying the study area are part of the Idaho-Wyoming Thrust Belt. At Caribou Mountain they have been intruded by diorite-monzodiorite. Where the intrusive rocks contact calcareous members of the thrust belt, skarn bodies have formed that host metal deposits. Gold, both placer and lode, occurs in the Caribou City area, and salt occurs in the Stump Creek area. Production records show 73.5 kg (2,363 ounces) of placer gold were produced; however, field studies indicate more than 2,000 kg (67,000 ounces) probably were recovered. Minor amounts of lode gold, silver, and copper were recovered from the hard rock mines. Production of salt from the Stump Creek study area in the 1860's was used by emigrants on the Oregon trail and also shipped to various mining districts for use in silver recovery. Oil and gas were drilled for, but all holes are plugged and abandoned. There are no current leases. Examined workings consisted of 25 adits, 3 shafts, 50 prospect pits, and extensive placer workings all in the northern tip of the Caribou City area, Current BLM records show 168 placer and 146 lode claims; 14 claims are patented.

Jan 1, 1993

This report describes the activities and publications of the Bureau of Mines Health and Safety Research and Testing Center, Pittsburgh, Pa., for the fiscal years 1960-65. It includes a discussion or work being conducted on roof control, dust explosions, ventilation, health, coal mine fire control, and electrical-mechanical testing, and an abstract of each paper published during the report period.

Jan 1, 1966

By Robert B. Fulton

Summary of data and estimates for 52 fluorspar properties in the following 13 foreign countries: Mexico Thailand China (PRC) Morocco Tunisia Italy Spain South Africa France United Kingdom Kenya Namibia Federal Republic of Germany Data includes deposit type, resource tonnage and grades, mining and beneficiation methods, annual production, fluorspar products and by-products, manpower requirements, capital and operating cost estimates. For operating properties, engineering and cost data have been developed for present and anticipated levels of production. Hypothetical operations have been assumed for undeveloped deposits.

Jan 1, 1984