Search Documents

By John Nagy

Experience and research have shown that an effective way to reduce structural damage from explosions is to provide adequate pressure-relief vents in the walls of equipment and buildings within which explosions might occur. In general, free or unrestricted openings represent the most efficient type of vent. However, in many manufacturing operations it is impractical to use free vents, and it becomes necessary to cover the openings with diaphragms or blow-out disks, hinged panels, or other devices, in order to give protection against weather changes, to prevent the efflux of dusts or vapors from equipment during normal operations, or for other reasons. A few data on the pressure-relieving capacities of hinged panels and a paper diaphragm were published in Bureau of Mines Report of Investigations 3924, which covered the first phase of the dust-explosion venting study made by the Bureau. The present report describes recent experiments that were made to determine the relative effectiveness of an unrestricted vent and 22 types of closures, including various paper, cloth, and metal-foil diaphragms, hinged doors or panels, and several kinds of scored and unscored glass panes. The tests showed that many of the vent closures were effective in releasing the explosions rapidly during their incipient stage, so that the development of destructive pressures was prevented. Vents of this type should prove useful in safeguarding industrial equipment from severe explosion damage. The experiments disclosed that the venting capacities of the diaphragms are approximately inversely proportional to their static bursting strengths.

Jan 1, 1950

By Thomas H. Dubaniewicz

The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, conducted a study of past mine explosions to identify the ignition locations and ignition sources responsible for the most severe explosion events resulting in death. Since the Scotia disaster of 1976, many fatalities from underground coal mine explosions have been linked to nonpermissible electrical equipment ignition sources located in intake air courses. With few exceptions, explosion protected equipment is generally not required in intake air courses of gassy underground coal mines in the US. Cigarette lighters were another prevalent ignition source for fatal explosions ignited in intake air courses. Several mine rescue/ recovery teams have encountered electrical ignition hazards. The study provides evidence that intake air courses of gassy underground coal mines fit the description of certain Hazardous (classified) locations described in the US National Electrical Code®. Class I Division 2 or Zone 2 explosion protection tech¬niques may be used to design intake air equipment so that it does not present an ignition source under normal operation, before mine power is shut down in emergency situations. Nonpermissible circuits in intake air courses that are likely to remain energized during emergencies, e.g. battery powered equipment, should be protected by more stringent Class I Division 1, Zone 1, or Zone 0 techniques, to protect rescue/recovery personnel.

Jan 1, 2009

By G. R. Hopkins

The petroleum-refining industry established a. new record in fuel effieciency at refineries in 1936, when 597,000 B. t. u. of heat mere required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the 'indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio ( crude runs divided by capacity) for re- fineries increases toward tine maximum of 100 percent, the fuel requirements show progressively smaller increases and the average B. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

In this U.S. Bureau of Mines report, in situ vat leach mineral recovery system concepts are described and cost compared with conventional mining and pad and autoclave leach processing systems. In the proposed systems, leachable ores are enclosed in place in reagent-impermeable in situ vat constructions. The ores are then rubbled and flood leached or flood oxidized and leached. The in situ vats are called stope leach or stope autoclave vessels. The report also proposes ore body-adjacent in situ vat constructions containing rechargeable processing stopes. A series of ore body-specific, innovative, and conventional mineral recovery systems case study designs are described and prefeasibility level costed. Based on a comparison of these prefeasibility level cost estimates, the proposed systems are determined to be economically competitive with conventional min¬eral recovery systems. The in situ vat leach mineral recovery systems concepts for leachable and refractory ores are developed around the drill-split narrow-vein and longwall mining methods described in part 1 of this Information Circular series.

Jan 1, 1995

By Patricia R. Devine

This report expands an earlier study by Jack Faucett Associates (OFR #40-88) of the same title. Both reports are based upon an interindustry analysis from 1963 through 1982, during which time U.S. metals consumption and production did not keep pace with economic growth. The report discusses three sources of change: technological change, economic growth, and composition of final demand, as well as the relative importance of the individual components of final demand for metals. The results show investment and personal consumption to be the most metal-intensive components of final demand, and technological change to be the major cause of decline in consumption growth during the study period. Technology change is defined as alterations in production processes resulting in more or less consumption of metal per unit of output, often because of material substitutions and design changes. A trade analysis shows the significance of import growth, particularly indirect imports (metal contained in imported goods) as a factor contributing to the reduced growth rate of domestic metal production. The effect of import growth is partially offset by indirect export growth, suggesting that continued increase of all U.S. exports can have a strong effect in reducing the negative trade balance in metals.

Jan 1, 1988

By R. R. Sayers

Under compuision of the present urgency to implement the President's promise to make the United States the arsenal for the democracies there is a tendency to demand a relaxation of restrictions on hours of labor and to speed up all industrial processes. The pressure is the more insistent with growing realization of the importance of the time factor in the success- ful prosecution of the war effort and the lack of skilled workers due to (2) operation of the draft, lack of an apprentice system in industry, and loss of skill by workers unemployed for long periods during the depression. With "total" war such as it is today the probabilities are that everyone will be required to exert greater effort (in many instances in activities to which they are unaccustomed) for longer periods than ever before has been necessary. The question arises, "What will be the aftereffects as well as the immediate effects on health, safety, and efficiency?" A review of the literature leaves the impression that this question has not been an- swered completely, especially as regards the ultimate effects. Mechanization, speeding up of industrial processes, mass produc- tion, and the small industrial concerns present many problems to indus- trial medicine. Does the tendency to expect the worker to produce at full speed all the time he is on the job decrease the effectiveness of the shorter working hours and cause undue fatigue, loss of efficiency, and increased accident proneness? The answer is important as this condition is likely to be intensified by the exigencies of the present emergency. According to Viteles (1)3, The increased tension under such conditions of work appears to offset the savings in muscular force made pos- sible by the machine. The tension, the speed, the subject- tion to specialization of work and a rhythm uncontrolled by the individual promote fatigue, characterized by a "decrease in the power to work, a decrease in pleasure taken in work, and a decrease in the enjoyment of the hours spent away from work."' The crowding of workers in temporary structures without proper provision for comfort and health may add greatly to the general fatigue factors already present in many industrial establishments. In 1932 Lockhart (2) stated that the production and maintenance of a healthy, satisfied industrial population is the most urgent necessity, involving problems so serious as to constitute a national task too great economically to be relegated to industrial concerns. If this was true in 1932, it must be doubly so today.

Jun 1, 1942

By BUREAU OF MINES

This summary of State laws on explosives was compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and , in general , how they have been treated . It does not include any legislation passed after 1942 , or any proclamations , regulations , or administrative orders . It does not purport or attempt to be authoritative . If any problem arises involving interpretation of the statutes of any particular State , the original source must be consulted for the exact words used by the legislature . This summary , however , will be useful in determining whether relevant statutes exist , and in locating thern quickly, with a minimum of effort . It will be of value also in comparing statutes in one State with similar statutes in other States to determine what construction has been placed upon them by the courts of these jurisdictions or to contrast the varying provisions of many States upon a similar subject . To make these comparisons easier , the statutory provisions for each State have been grouped under several major topics in outline form . Although this sometimes has resulted in disruption of the continuity of individual acts , the increased general clarity and availability of comparable sections have more than justified the procedure followed ,

Jul 1, 1943

By Lucia Kuizon

In 1986 and 1987, at the request of the U.S. Forest Service, the U.S. Bureau of Mines studied the Diamond Peak area comprising 183,000 acres in the Challis and Targhee National Forests in order to evaluate its identified mineral resources. More than 3,000 mining claims were located in three mining districts between the years 1882 and 1986. Approximately 230 mining claims in and the 150 claims adjacent to the study area were current in 1986, when Bureau of Land Management mining records were researched for this study. A total of 1,270 samples were collected from these sites (30 were for alluvial placer). Results of the investigation help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Lead-, silver-, zinc-, copper-, and gold-bearing minerals occur as veins and replacement bodies in shear and fault zones in Precambrian and Paleozoic calcareous Sedimentary rocks that have been complexly folded and faulted. Total production from the three mining districts in the study area was more than 150,000 tons of ore between 1901 and 1982. Approximately 11,600 tons of subeconomic resources consisting of lead, silver, zinc and copper were identified within the area. Over 37,500 tons of lead and zinc subeconomic resources were identified just outside the area. In addition, lead-, silver-, and zinc-mineral resources were identified at 4 mines within 2 miles of the study area. Iron mineral resources were also identified just outside the area.

Jan 1, 1991

By L. Crocker

The Bureau of Mines investigated processes for recovering a marketable lithium product from the montmorillonite-type clays of the McDermitt caldera. The clay deposit, located on the Nevada-Oregon border, is estimated to contain over 3 million short tons of lithium. Limestone-gypsum roasting and selective chlorination proved most successful for extracting lithium from the clays; 80-pct Li recovery was achieved using either technique. With both processes, lithium silicate in the clay was converted to a water-soluble compound-either lithium sulfate or lithium chloride. The lithium was then recovered as a carbonate by water leaching the calcine, concentrating the leach solution by evaporation, and precipitating the lithium with soda ash. The operating costs for the limestone-gypsum roast process were estimated at $2.02/lb Li2C03; selective chlorination operating costs were estimated at $3.85/1b Li2C03. The current selling price of Li2C03 is about $1.50/lb. A detailed flowsheet, material balance, and process evaluation are presented for the limestone-gypsum roast process. In addition, lithium reserves and resources are discussed and the McDermitt clays are described.

Jan 1, 1988

By Charles K. Rose

This paper presents some research studies of the rotary drilling of oil shale at the Bureau of Mines Oil-Shale Mine, Rifle, Colo. The experimental procedures and the rotary drill test equipment are described. Theories of rock drillability, rotary bit cutting action, and bit design are presented and discussed. The actions of various bit designs are analyzed and compared with the observed results of actual drilling tests. A cost estimate is made for drilling Colorado oil shale.

Jan 1, 1955

By Launa G. Mallett, Charles Vaught, Dana C. Reinke, Lisa J. Steiner, Lynn L. Rethi, Kathleen M. Kowalski-Trakofler, Jr. Brnich, William J. Wiehagen

Safety and health professionals recognize that training is a critical element of any effective safety and health program. An extensive literature survey has led the authors to conclude that we are at the beginning of a revolution in training due to changes in the demographics of the workforce, the rapid growth of technology, and the universal ascendance of the information age. Of present major concern in the mining industry is how to provide appropriate training for an aging workforce and concurrently develop training for the expected influx of new and less experienced miners as older workers retire. This report explores the key issues in the changing safety and health training area as identified by the multidisciplinary team of NIOSH researchers who conducted the literature survey. Issues include generational differences between newer mine workers and the present workforce with respect to their physical, psychological, social, and cultural characteristics; their learning styles and work expectations; and the impact of technology. Some preliminary conclusions are offered for future training needs.

Jul 1, 2004

By L. Allan White

Instrumental analysis is an indispensable tool to many phases of research on rare-earth metals and their compounds; therefore, the development of new and improved instrumental techniques is essential. This report describes an emission spectrometric analytical method using direct-current carbon-arc excitation of various rare-earth-oxide mixtures. Lanthanum oxide serves the dual purpose of an internal standard and a constant major constituent. The versatility of the method was demonstrated by three different applications: (a) Analysis of complex rare-earth concentrates; (b) determination of impurities in high-purity rare-earth oxides; and (c) detection of rare-earth elements in other types of matrices, such as those resulting from beneficiation of rare-earth ores. The average error of analysis in the concentration range of 0.2 to 10.0 percent was 14.6 percent for a group of complex synthetic mixtures of rare-earth oxides. An average error of analysis in the concentration range of 0.05 to 0.50 percent was 21 percent for a group of high-purity rare-earth oxides.

Jan 1, 1959

By W. R. Hardwick

This information circular describes open-pit mining methods and practices of the Bagdad Copper Corp., Yavapai County, Ariz. It is one of a series being prepared by the Federal Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. A brief history of the Eureka district and of early developments at the [gdad] mine is given, and the are deposit is described with particular emphasis on those characteristics (physical, economic, or engineering) that affected the choice of mining methods. Prospecting, exploration, and sampling and estimating the tonnage and grade are outlined. Development of the open-pit mine is shown. Mining methods, including breaking ground, primary drilling and blasting, secondary drilling and blasting, loading, transportation, engineering, and operating control, are described. A brief summary of mining equipment is given. Percentage of extraction, production rate, mine drainage and water supply, wage, contract, and bonus systems, safety and fire prevention, and the processing plant also are described. The last section gives a breakdown of such costs as are available for publication.

Jan 1, 1959

By D. G. Kesterke

The electrolytic reduction of uranium dioxide to molten uranium in fluoride baths at approximately 1,200° C was demonstrated. Electrolyte constituents were BaF2, UF4, and either MgF2 or LiF. Preliminary laboratory-scale experiments were made in which the uranium oxide was added continuously for 3 to 5 hours to the cell during electrolysis. Over 1,000 grams of metal of 99-8 percent purity was made in some tests, Major impurities were aluminum, barium, iron, silicon, carbon, and oxygen. The effects of cell design, geometry, and bath composition were investigated. Electrode arrangement was the most important factor in cell performance.

Jan 1, 1963

By John J. Mulligan

The Bureau of Mines investigated the tin deposits of the Cape Mountain area during July and August 1962 to test the effectiveness of detrital-cover sampling in permafrost areas as a relatively cheap and simple means of guiding mine development and exploration. Results indicate that systematic detrita1-cover sampling can be used effectively to delineate obscure deposits with sufficient accuracy to permit sampling with a minimum of trenching or drilling. Extensions of known outcroppings were traced in sufficient detail to guide lode sampling and several previously unknown tin-bearing lodes were found and sampled. Lode sampling was limited to the minimum needed to establish the reliability of detrital-cover sampling results. The results of previous lode and placer investigations are summarized and detrital-cover sampling methods and results are described in detail.

Jan 1, 1966

By T. Kessler

Spark-source mass spectrometry has been used to determine the amounts of minor and trace elements in coal particles of various sizes, including the respirable range (<5 microns). Fifty-six elements ranging in concentration from 0.1 ppm wt to 5,000 ppm wt have been determined. The investigation of coal and coal ash has shown that the organic material in coal does not interfere with the spark-source determination of the various elements.

Jan 1, 1971

By E. R. Andersen, F. E. Block, T. T. Campbell

This work was done to develop methods for increasing the yields and purity of vanadium prepared by bomb reduction of vanadium compounds . Compounds reduced were V₂ 05 , V203 , VC , and VC13 . Sodium , calcium , and magnesium were used as reductants . Variables considered included reductant form , bomb size , pressure during reaction , method of ignition , and the use of slag fluidizing additives . It was concluded that yields of 85 to 90 percent can be effected by the calcium reduction of V205 in reactors measuring as much as 14 inches in diameter and 60 inches in height . Optimum charge composition included V₂05 , 65 percent excess calcium , and 0.4 moles sulfur per mole vanadium . Purity of the vanadium produced in large reactors varied from 99.5 to 99.8 percent . The higher purity metal , depending upon the amounts of interstitial impurities present , was usually cold ductile . Although high yields of up to 99.5 percent can be effected by bomb reduction of VC1 , the high pressures developed in the bombs and attack of the reactor walls by the byproduct chloride slags discourages this method of preparing vanadium . It was found that significant purification of impure regulus metal occurred when it was hydrided , crushed , acid leached , and vacuum dehydrided . Metal so treated can readily be converted to ductile sheet . A cost estimate based on the production of 100 tons of vanadium per year was prepared . It was concluded that pure ductile vanadium could be produced for approximately $ 20.00 per pound .

Jan 1, 1964

By Donald O. Capstick

A mineral survey of the 520-acre Quigg West Wilderness Study Area (MT-074-155) was conducted by the U.S. Bureau of Mines in 1986 at the request of the U.S. Bureau of Land Management in order to evaluate its identified mineral resources. The Wilderness Study Area is in Granite County in western Montana about 16 miles northwest of Phillipsburg and 27 mi les northeast of Hamilton, MT. Stony Mountain, a study area on lands administered by the U.S. Forest Service, is about 1 mile to the south-southwest and was studied concurrently. No mineral resources were identified in the Quigg West Wilderness Study Area, but high grade gold assays, as much as 1.24 ounce gold per ton, were obtained at the one prospect found. Samples from four workings contained significant gold; minor silver, molybdenum, and copper were also present. The prospect containing the narrow and discontinuous gold-bearing quartz vein straddles the south boundary of the Wilderness Study Area. The shear zone containing the vein projects toward the old Crescent mine, about 4.5 miles to the south, which shows a similar geologic structure.

Jan 1, 1987

By D. Harrington

The desirability of efficient control of air currents, and the necessity of supplying metal-mine workers with better and safer working conditions, has created an active interest in metal-mine ventilation, especially in recent years. This paper discusses the subject both with regard to efficiency and economy, as well as safety and health. It is based on personal observations of the writer from over four year's study of metal mines in six States, in which more than 50 mines were visited. Many of these were studied in detail; in all several thousand working places were examined, and readings taken relative to ventilation run into the tens of thousands.Object of ventilating metal mines:Whereas in coal mines ventilation is generally regarded as essential, in many metal mines, especially shallow ones, the operators pay little attention to ventilation, or ignore it altogether. Recent shortage of labor, and numerous accidents to which State compensation laws have directed attention, are causing metal-mine operators to regard ventilation more seriously, especially in deep, large mines.There is, in fact, greater necessity for adequate ventilation of metal mines than of coal mines. The latter require air currents to remove explosive gases and the fumes of explosives, but metal mines, in addition to the need of removing fumes of explosives, and occasionally explosive gases, frequently have need of removing dusts dangerous to health, reduction of high temperatures and high humidity, and removal of inert but unhealthful gases like CO2 and nitrugen. The generally accepted superior healthfulness of coal miners as compared with metal miners, is probably due in large part to the better air circulation in working places of coal mines.

Jun 1, 1920

By R. D. Brown

There are techniques for separating aluminum alloys from mixed scrap, but there are no efficient ways to separate wrought aluminum from cast aluminum. This Bureau of Mines report describes a novel technique for separating mixed aluminum alloy scrap into cast and wrought aluminum alloy fractions. The technique, which uses conventional heating, fragmentizing, and screening equipment, exploits differences in the mechanical properties of cast and wrought aluminum alloys at elevated temperatures. The cast alloys become brittle at high temperatures owing to intergranular melting of regions of eutectic composition. This melting begins to occur as the solidus temperature for each alloy is reached. Solidus temperatures for casting alloys generally range from 520° to 580° C, but are above 600° C for most wrought alloys. Thus, the casting alloys are easily fragmented while the wrought alloys remain ductile in the proper temperature range. Starting with a mixture containing approximately 80 pct cast and 20 pct wrought alloys, fractions of 100 pct cast and 98 pct wrought have been produced.

Jan 1, 1985