Search Documents

By S. J. Pearce

There are a number of methods for determining relatively small quantities of sulfur dioxide in air. However, those methods require fairly elaborate apparatus and laboratory facilities. Frequently in industrial hygiene surveys it is desirable to have a simple arrangement to obtain "on the spot" determinations. This has been accomplished for concentrations of sulfur dioxide of hygienic significance by using the midget impinger and decolorizing a starch-iodine solution.

Jan 1, 1948

By R. Karl Zipf

This report presents nearly all structural data available from explosion tests of 20-psi mine ventilation seals and concrete-block ventilation stoppings that were conducted by the National Institute for Occupational Safety and Health during 1997?2008. Although the seals tested were designed to meet the former federal 20-psi pressure design standard, the structural information contained herein on these seal tests will facilitate the analysis and design of coal mine seals that meet the new explosion pressure design criteria of 50 and 120 psi as set forth in the Mine Safety and Health Administration (MSHA)?s final rule on ?Sealing of Abandoned Areas.? The seal testing data are organized into six broad categories of seal structures based on the materials used and the construction method for those 20-psi seals: 1. Concretelike materials with steel reinforcement and reinforcement bar anchorage to rock 2. Pumpable cementitious materials of varying compressive strengths with no steel reinforcement and no hitching 3. Articulated structures such as solid-concrete-block seals and ventilation stoppings made of solid and hollow-core concrete blocks 4. Polymer and aggregate materials without hitching 5. Wood-crib-block seals with or without hitching 6. Articulated structures such as lightweight blocks with or without hitching This summary contains data on 52 different structures in the above categories?44 seals and 8 ventilation stoppings. The structural data sets include the applied loading on the tested seal represented by a pressure-time curve and, when available, the measured seal response represented by a displacement-time curve. The structural data sets enable the calibration and verification of numerical models of seal behavior at the 20-psi level, which may then facilitate future structural analyses of seal designs for the new 50- and 120-psi explosion pressure design criteria.

Aug 1, 2008

By Raja V. Ramani

The recognition that surface mining need not be viewed as a permanent dedication of the land but rather as a temporary non-renewable use in a series of land uses has caused greater emphasis on the re-use of surface-mined lands. In an effort to develop a procedure for evaluating postmining land use potentials, specific mines in various regions of the U.S. have been studied to determine the extent of current mined-land planning and to discover characteristics that are regional in nature. As part of this investigation, the Indian Head Mine, which is located in Mercer County, North Dakota, has been studied. The Indian Head Mine is presently operated by The North American Coal Corporation -Western Division and has been in operation since 1917 under various ownership. The status of current reclamation and postmining land use planning was reviewed. In addition, the relationship between mine planning and public planning in an area impacted by energy development was investigated. Finally, key factors affecting site potential realization for western surface mines have been identified.

Jan 1, 1983

By J. W. Walkiewicz

The Bureau of Mines investigated alloys containing lanthanum (La), praseodymium (Pr), neodymium (Nd), cobalt (Co), copper (Cu), iron (Fe), and magnesium (4g) as possible components of a permanent magnet mate¬rial utilizing a cerium-free synthetic mischmetal (M) as a substitute for scarce samarium (Sm) metal. Magnets containing M-Co-Cu-Mg and M-Co-Cu-Fe-Mg were fabricated by powder metallurgy techniques and evaluated. A synthetic mischmetal (M20) containing 20 pct La, 60 Pr, and 20 Nd yielded the best overall magnetic properties. The M20-Co-Cu-Mg alloys had energy products as high as 13.2 MGOe, remanences as high as 7.89 kG, normal coercivities as high as 6.26 kOe, and intrinsic coercivities as high as 13.4 kOe. The best value of intrinsic coercivity, 22.9 kOe, was obtained with an M-Co-Cu-Mg magnet in which the synthetic misch¬metal contained 30 pct La, 50 Pr, and 20 Nd. These values compare favorably with those of the Sm-Co magnets fabricated and measured at the Bureau's Reno Research Center, which had energy product of 15.1 MGOe, remanence of 7.8 kG, normal coercivity of 7.5 kOe, and intrinsic coercivity of 27.4 kOe. Iron substitution for part of the cobalt resulted in a decrease of magnetic properties, although several percent iron can be added before a drastic loss of magnetic properties occurs.

Jan 1, 1983

By Richard D. Miller

The helium resources base of the United States was estimated by the U.S. Bureau of Mines (Bureau) to be 894.6 Bcf as of January 1, 1989. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 282.4 Bcf, (2) helium in probable natural gas resources, estimated at 237.7 Bcf, (3) helium in possible natural gas resources, estimated at 263.1 Bcf and (4) helium in speculative natural gas resources, estimated at 111.4 Bef. These helium resources are further divided into depleting and nondepleting, with the helium in storage being in a classification. The depleting resources are those associated with natural gasfields that are, or will be produced for the natural gas they contain. Almost all of the helium in potential (probable, possible and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 775 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, i.e., those in shut-in, abandoned, or otherwise nonproducing natural gas fields, are estimated to total 84 Bcf There is 35 Bcf of helium in storage in the Federal Government-owned Cliffside Gasfield near Amarillo, TX.

Jan 1, 1990

By Richard F. Hewlett

This report describes how a limited number of preliminary exploration drill-hole assays from a mineral deposit can be used to design grid spacing that is both economic and efficient for subsequent evaluation drilling of that deposit. Relationships between desired precision of the estimate of grade of ore and drilling cost are used to determine the economic drill-hole spacing. The statistical concept of precision in estimating grade of ore is used to determine the efficient drill-hole spacing. Assay data from approximately 50 known copper deposits were studied, and the relationships of the statistical parameters of these deposits were computed. Drilling requirements for various precisions of the estimates of grade of ore were computed for some of these known deposits to serve as guides for drilling future copper deposits. The effect of various geologic factors on the trend in grade of ore and, therefore, on the drilling requirements is shown for certain deposits.

Jan 1, 1965

By Eric R. Bauer

The ground control aspects of extended depth-of-cut mining are presented in this U.S. Bureau of Mines report. A trend analysis of extended cut approvals was performed. A comparative review of roof fall fatalities for extended and nonextended cut mining is included. Current ground control guidelines for extended cut approval are summarized. The problems and concerns of this extraction system are addressed, and typical extended cutting face operations are described.

Jan 1, 1993

By P. A. Hendricks

This U.S. Bureau of Mines (USBM) report identifies and evaluates factors responsible for metal/nonmetal (M/NM) underground mining accidents involving mobile equipment. Information regarding the occurrence and severity of the accidents, the type of equipment involved, the primary and contributing causes, and preventive measures is included. The goal of this report is to provide information that will aid mine operators and safety managers in the recognition of hazards associated with operating mobile mining equipment in an underground mining environment.

Jan 1, 1994

By Dale W. Richardson

Ductile hafnium was not obtained consistently by the conventional Kroll process. The bimetal reduction modification produced a more ductile hafnium by lowering the impurities, especially oxygen, in the sponge metal. Hafnium oxide was chlorinated in the presence of carbon to form anhydrous hafnium tetrachloride, which was reduced by sodium and magnesium in an inert atmosphere to produce sponge hafnium metal. After vacuum distillation to remove the byproducts, the sponge was arc-melted into ingot and rolled into strip. Metallic impurities were decreased by evaporating the hafnium tetrachloride from a fused salt. An excessive amount (over 1,200 parts per million (p.p.m.)) of aluminum was contained in some of the hafnium oxide, much of which remained as aluminum chloride in the hafnium tetrachloride during chlorination. Evaporation of the hafnium tetrachloride from a fused NaCI-KCI mixture during the Mg-Na reduction greatly lowered its aluminum content, as most of the aluminum and some of the other metallic impurities were retained by the fused salt.

Jan 1, 1961

By Ned Baker

This report describes the development, construction and testing of a hydrogen-fueled underground mining vehicle. A hydrogen burning engine and a hydride fuel system, both previously developed, were installed on a modified utility vehicle, together with the necessary controls. In tests and in actual use, the vehicle performance in terms of speed, acceleration, and gradeability exceeded that of the standard, unmodified vehicle.

Jan 1, 1985

By J. W. Paul

This circular is one of a series of reports on coal mining methods and cost s which are being prepared by the U. S. Bureau of Mines for the purpose of making available to those interested in the industry a knowledge of the mining methods employed in mines where mechanical and hand loading is practiced and the cost data on the several operations pertaining to the removal of coal from the working faces and its transportation to the tipple for loading into railroad cars. The methods employed are influenced by the natural local conditions with respect to the thickness and character of the coal beds and the overlying strata, the means employed for roof support and its control, and the disadvantages incident to the development of mines in thin coal beds.

Jan 1, 1929

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grind-ability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1965

By Glenn A. Hazen

This report presents a stress investigation of four coal pillars located under two depths of cover. Each coal pillar was instrumented with ten load cells designed to measure coal pressure during initial and secondary mining. The problem considered was one of uniform triaxial stress as a large coal pillar was loaded under a thick limestone bed. Special attention was given to pillar design procedure. Unconfined uniaxial compression tests were conducted for coal specimens 7/8 in., 2-1/8 in., 3 in., and 4 in. square with length to square side ratios of 1/2, 1, 1-1/2, and 2. Stress-strain curves were recorded. Six specimens were tested at each size. Results show that a coal pillar is composed of an inner zone which is highly loaded plus a region around its perimeter which has lost its elastic strength. The bearing capacity of a coal pillar consists of elastic and crushed coal response: The failure strengths have been determined and will be useful in coal recovery, mine design, and mine safety.

Jan 1, 1975

By G. S. Scott. R. L. Grant

Ammonium nitrate (NH4NO3), a white crystalline chemical compound composed of 35 percent nitrogen, 60 percent oxygen, and 5 percent hydrogen, has again attracted attention, due largely to the recent catastrophe on April 16 and 17, 1947, at Texas City, Tex. The fire and subsequent explosion on the steamship Ocean Liberty, outside the harbor of Brest, France, on July 28, 1947, has fur- ther increased the interest in the properties of ammonium nitrate. As a result of the Texas City disaster, several laboratories have undertaken research to determine more certainly what causes ammonium nitrate to detonate and under what circumstances. This is not the first time that ammonium nitrate has been involved in a disaster, and its properties reviewed from the standpoint of safety. The disaster at Oppau, Germany, in 1921, which involved an equimolec- ular mixture of ammonium nitrate and ammonium sulfate, prompted an intensive study in Europe and in America. In the United States the properties of am- monium nitrate are now of especial concern because very large quantites are being manufactured and shipped in interstate commerce and abroad. Many an- monium nitrate factories, which were built during the war, will manufacture increasing amounts of this compound for use as a fertilizer. It is the purpose of this report to present a brief summary and biblio- graphy of the published experimental facts about the properties and behavior of ammonium nitrate. The reader is referred to original publications for greater details of the investigative work, and for theoretical discussions. This report also includes a survey of ammonium nitrate fertilizer of the type involved in the Texas City explosions. In the past, authorities have not always agreed on the degree of hazard involved in the manufacture and handling of ammonium nitrate, as the following quotations from the literature indicate: Munroe (82) quoted the following from Turner's Chemistry (a book pub- lished in 1835): "When this salt is exposed to fire, it liquefies, emits aqueous vapor, dries and detonates." Berthelot (14) in his book, Explosives and Their Power, 1983, wrote: "Ammonium nitrate from the point of view of its volatility, and cn account of many considerations, may be regarded as a typical explosive substance."

Jun 1, 1948

By William H. King

The Mining Division of the Bureau of Mines has been making development and power-requirement studios for the Interior Department Missouri Basin Field. Committee. The studies by the Bureau of Mines have as their purpose, the summarizing of potential future power requirements in the mineral industry within the Missouri Basin, special emphasis being placed on possible expansion of these requirements through construction of new mining enterprises by private capital. In preparing a proposal for the production of phosphoric acid from phosphate rock near Lander, Wyo., it was found that the basic information on the physical and chemical characteristics of the phosphate beds to determine costs of mining and treatment was lacking.

Jan 1, 1949

By J. Hyvarinen, A. D. Look

"INTRODUCTION AND SUMMARYElectricity is used extensively in open-pit metal mines to provide illumination, heat, and power to operate hauling and loading equipment, drills, pumps, signal systems, and other machinery. Good installation and maintenance of equipment and power, circuits, are essential to minimize the hazards of shock, burns, and fire.In the 13 years from 1931 to 1943, 20 fatal and 82 nonfatal injuries resulted from the use of electricity in open-pit mines in the United States ; 4/ these figures represent about, 10 percent of all fatalities and 1 percent of the nonfatal injuries. The ratio of fatal to nonfatal injuries from electricity in such mines was very high during this period; the figures show one fatality to every five accidents from this cause.Electricity may cause personal injury through abnormalities in equipment, such as short-circuit, accidental ground, overload, and poor contact; however, each year some fatal electrical accidents are due to persons touching uninsulated ""live wires."" These contact injuries are the result of careless body movements of persons in the vicinity of 'wires at places not normally frequented, or of accidental contact with live circuits when handling metal objects. Electrical hazards can be minimized by the enclosure or elevation of current-carrying parts; ample working space around equipment, adequate insulation, locking switches in the open or closed position under certain conditions, identifying and warning devices, protective grounding, insulating flooring, platforms, or rubber gloves, and proper inspection and maintenance."

Apr 1, 1949

By William Y. Mo

This report presents preliminary results of a study undertaken to investigate quantitative characteristics of the demand for steel mill products and its major end-use components. The major end uses included in the study are the steel mill products used in construction, in automobiles, in producer durables, and in consumer durables. The main objectives of the research underlying this study are as follows: (1) To formulate and estimate the empirical demand relations for steel and the four major end uses in the United States; (2) to measure and calculate the responsiveness of the U.S. per capita steel consumption with respect to the changes of the steel and other nonferrous metals prices; (3) to determine and quantify the relative importance of the underlying demand explanatory factors in contributing to the average year-to-year increases (or decreases) of the U.S. per capita steel consumption; and (4) to adapt and use the estimated demand relations in making projections of the U.S. future demand for steel and the major end-use components. After extensive preliminary investigation, three versions of simple linear demand relations are selected and estimated by means of ordinary least squares (OLS) method. The annual data for the period 1947-65 are used in the estimation. Direct and cross price elasticities of demand are computed for each of major end uses. The relative importance of demand explanatory factors in contributing to the average year-to-year changes of U.S. per capita steel consumption are also calculated. For making projections, a simple autoregressive time trend model is used in estimating the future values of independent variables. Since the estimated demand relations are valid for projections only if the estimated parameters can be assumed to be unchanged in the future, and consequently, the projections derived in the study should be interpreted accordingly.

Jan 1, 1970

By L. B. Berger

"INTRODUCTION Accurate determination of carbon monoxide in concentrations ranging from 0.2 to about 0.5 percent by volume is troublesome, because such concentrations are too high for some analytical methods and too low for others. Methods that are sensitive to concentrations of carbon monoxide considerably less than 0.2 percent are approaching their upper limit of usefulness when applied to the analysis of samples containing 0.2 percent or more of carbon monoxide, and it may be necessary to resort to dilution of the sample with a known proportion of air, or otherwise modifying the analytical technique, to obtain satisfactory results. Such methods include the determination of carbon monoxide by reduction of heated iodine pentoxide 3/4/5/ by the ""Pyrotannic acid"" method 6/ and by the so-called ""phosphomolybdic acid"" method. 7/ The use of conventional gas-analysis equipment, such as the Orsat type, in the determination of carbon monoxide in concentrations ranging from 0.2 to 0.5 percent is not desirable, as possible analytical errors may be of about the same magnitude, thus producing results of little quantitative value.For several years prior to this publication, the Gas Analysis Laboratory of the Health Division of the Bureau of Mines has used a modification of the Haldane type 8/9/10/ gas-analysis apparatus for the determination, by absorption in a chemical reagent, of carbon monoxide in low concentrations that are not readily determined by other methods. The method is applicable also to the determination of higher concentrations. As the procedure has proved successful and has been adopted by others, this report was prepared to describe the method and to present results of analyses obtained with it."

Nov 1, 1947

By Curtis D. Edgerton

The Pittsburgh Mine Map Repository of the Bureau of Mines serves as a basic reference file for the archival preservation of mine map data of mines east of the Mississippi River. About 22,000 of an estimated 500,000 available mine maps have been microfilmed A computerized index serves as the mechanism for retrieval of any microfilmed mine map. The operation, equipment, and index are described in the report.

Jan 1, 1974

By Floyd R. Hertweck

The helium resources of the United States were estimated by the Bureau of Mines to be 1,037 Bcf as of January 1, 1981. These resources are divided into four categories, in decreasing degree of assurance of their existence: (1) helium in storage and in measured natural gas reserves, which totals 211 Bcf, (2) helium in indicated natural gas resources, which is estimated at 207 Bcf, (3) helium in hypothetical natural gas resources, which is estimated to be 318 Bcf, and (4) helium in speculative natural gas resources, which makes up the remaining 301 Bcf. These helium resources are further divided into depleting, nondepleting, and stored classifications, The depleting resources are those associated with natural gasfields that are, or will be, produced for the natural gas they contain. All of the helium in undiscovered (hypothetical and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 897 Bcf of the total helium resource base. Nondepleting resources are those in shut-in, abandoned, or otherwise nonproducing natural gasfields. Helium resources contained in nondepleting natural gas resources are estimated to total 100 Bcf. There is 40 Bcf of helium in storage in the Federal Government-owned Cliffside Gas Field near Amarillo, Tex.

Jan 1, 1983