Search Documents

Unfortunate occurrences resulting in injuries, loss of life, and destruction of property by explosion, fire, and other mishaps during shaft sinking in the past few years have focused the attention of the Bureau of Mines on the need for safety standards for such operations. Several States have some rules and regulations applicable to local conditions, and several Bureau publications (including some now out of print) cover the hazards that may be encountered in shaft sinking. Certain requirements of the Federal Mine Safety Code and Federal Coal Mine Safety Act may be applied, but there are no definite, uniform standards that will guide those desiring to sink a shaft safely and bring about uniform safety inspections.

Jan 1, 1957

By Franklin H. Persse

To meet escalating energy requirements, substantial increases in production from the strippable coal and lignite deposits in eastern Montana, western North Dakota, and northeastern Wyoming already have occurred, and further expansions are expected at least until the year 2000. Such production, attributable largely to rising demand for low-sulfur coal, must be accomplished with a minimum of adverse effects on the environment. Information on geology, climate, and current land use in the Upper Missouri River basin is presented in the Bureau of Mines review as a guideline to what operators may expect during and after mining. Proven methods of protecting the air and water from pollution and of restoring mined land for other uses are described, and untried methods of land reclamation, some with equipment yet to be manufactured, are discussed as possible means of maintaining aesthetic values in the basin. Costs incurred to protect the environment are part of the production cost and thus are borne by the ultimate consumer. Unit production costs are less for the thick coal and lignite deposits of the basin than for the thinner but higher Btu coal deposits of the Eastern and Midwestern United States. Precise comparisons of environmental protection costs between mines in such disparate areas cannot be made, because of differences in physical conditions, accounting procedures, and other variables.

Jan 1, 1975

By John H. Johnson

White Pine Mine section designated for exhaust emissions studies. The MTU Mine Air Monitoring Laboratory was used to gather temperature and C02 concentration data at 10 locations. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in stratification in dead end headings. Diesel mine-vehicle tailpipe emissions were monitored in the laboratory by a portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. Diesel pollutant concentration data from the Orchard Valley Mine were analyzed and compared with data collected earlier in the White Pine and Brushy Creek mines. Lognormal frequency distributions and CO2-based concentration ratios and correlations were calculated. In the three mines compared, pollutant concentrations were distributed similarly, and concentrations appear to be controlled to present standards.

Jan 1, 1979

By Hugh D. Pallister

Alabama probably has the most extensive deposits of high-grade flake graphite in the United States and was the largest producer during World War I. Therefore, with the outbreak of World War II, users of flake graphite turned again to Alabama to supply their requirements. Flake graphite is the most important ingredient contained in graphite crucibles used in melting crucible steel and special alloys essential for war purposes. Early in World War II the Army and Navy placed flake graphite on the list of critical war materials. During World War I, when the supply of Ceylon graphite (then in demand) was cut off, large quantities of flake graphite were produced in Alabama, and about 40 mills were built. Most of these were abandoned after the war when imports of the cheaper Madagascar flake (which gradually replaced Ceylon graphite) began to reach this country. With the beginning of World War II, the Madagascar supply was cut off', and consumers were again compelled to look to domestic sources for their supplies. They found only one small mill in operation, that of the Ceylon Graphite Co. in Coosa County, Ala. The Bureau of Mines made a preliminary examination of the Alabama flake graphite deposits in 1940. Samples were taken and tested at the Southern Experiment Station at Tuscaloosa.

Jan 1, 1948

By Alfred E. Schwaneke

A new high-temperature soft soldering system has been developed by the Bureau of Mines for use on copper, copper alloys, and low-carbon steel; the method is applicable to automobile radiators and home appliances. The system uses a unique sacrificial metal coating method to promote spontaneous wetting and spreading of zinc and zinc alloy solder: on metallic substrates. The 10-5 to 10-6 cm thick, electroplated or sputtered, sacrificial nickel coating is absorbed by the molten filler alloy during soldering and produces a direct solder-substrate metallic bond. Preliminary measurements on butt joints with copper members give tensile strengths up to 22,000 psi at room temperature using 95 Zn-5 Al alloy as solder. Spontaneous wetting, spreading, and capillary penetration are extremely rapid and produce joints as easily as 50-50 tin-lead solders. Recrystallization or annealing of the wrought copper joint members is negligible at the soldering temperatures of 450° to 490° C and lower. A list of fluxes and solder alloys is included in the report.

Jan 1, 1970

By Andrew F. Conn

This report summarizes the results from the first year of an anticipated multiphase program to develop improved coal mining equipment which utilize the CAVIJET? cavitating water jet method. This laboratory parametric study demonstrated the advantages of cavitating jets over non­cavitating jets in cutting coal, by producing comparable slot depths at one-fifth of the operating pressure, at better than one-half of the spe­cific energy. These results suggest that CAVIJET-augmented mining devices can be developed with compact, low-pressure pumps. Thus, CAVIJET should be capable of operating with safer, lighter support equipment, while providing all of the advantages (reduction of dust and sparks, reduced damage to cutters) of conventional hydraulic mining methods.

Jan 1, 1976

By Albert L. Toenges

ALMOST all of the coal used for metallurgical purposes west of the Continental Divide is ruined from the Lower Sunnyside bed in Carbon County, Utah. Coke produced from Lower Sunnyside coal and used in western steel plants is weaker structurally than coke used elsewhere in this country. For this reason, western coal operators and steel manufacturers are anxious to develop new areas of coking coal of better quality than the coal produced from the Sunnyside bed. Early in the war, the Bureau of Mines undertook an intensive investigation of western coals to (a) develop additional reserves of coking coal to supplement proved reserves in the Sunnyside bed and (b) develop, if possible, reserves of coal with coking qualities superior to Lower Sunnyside coal. Results of investigations in the Kemmerer district, Wyoming,9 and in the Minnesota Creek area, Gunnison County, Colo.,10 have been published.

Jan 1, 1952

By Nils A. Eilertsen

This Bureau of Mines report describes the unit cost procedure for estimating direct development costs within a cave block in an undercut block caving mine. Costs of supervision, labor, equipment, and supplies are combined to build a unit cost for each type and size of mine development opening in the block. These costs are then combined to estimate the direct cost for developing a ton of ore. Operating data from several domestic metal mines are combined with a hypothetical mining system to illustrate the costing procedure.

Jan 1, 1975

By Rolland L. Blake

The Bureau of Mines investigated the mineralogy, tonnage, and beneficiating characteristics of oxidized (nonmagnetic) taconite iron resources of the Western Mesabi Range as part of its program to insure adequate future domestic mineral supplies. Magnetic taconite currently provides about 95 pct of Mesabi production, but the large tonnages of oxidized taconite between the magnetic deposits will be needed to help meet future domestic demand for iron ore. Three bulk samples that represent large tonnages from the Western Mesabi Range were selected to determine their mineral composition and liberation by light optical microscopy and to test their beneficiating response. This report describes the mineralogy and liberation characteristics of the three samples of the Biwabik Iron-Formation for 26.5 mi (42.7 kID) from Keewatin to Grand Rapids, MN. (Details of response to beneficia-tion were reported previously.) The samples represent mostly material from the Lower Cherty Member of the Biwabik-Iron Formation, although one sample included some Upper Cherty Member. Minerals of all three samples were quartz (chert), hematite, goethite, and minor to trace amounts of magnetite, iron carbonate, and iron silicates. It was concluded that the oxidized taconites of the Western Mesabi Range represent a subeconomic indicated resource that can be selectively mined and beneficiated as a future large source of iron feed for steelmaking.

Jan 1, 1983

By A. J. Kraemer

This paper is the third and concluding report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relative to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 3129. The second report dealt with the data of the twenty-third survey in accordance with the revised specifications for United States Government Motor Gasoline. These data were published as Report of Investigations 3142.

Jan 1, 1931

By A. J. Kraemer

This paper is the third and concluding report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relative to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 3129.7 The second report dealt with the data of the twenty-third survey in accordance with the revised specifications for United States Government Motor Gasoline. These data were published as Report of Investigations 3142.8

Jan 1, 1931

By Robert R. Stein

Using an automated drill test fooure, the U.S. Bureau of Mines measured the sound power levels produced by a small, pneumatic, rotary roof drill. A series of tests was conducted to determine (1) the relative effectiveness of several drill muffling schemes and (2) the relationship between drill sound power and pneumatic power supplied to the drill. The influence of rotation rate (i.e., airflow) and feed thrust on the penetration rate of the drill was also noted.

Jan 1, 1989

By Felix du Breuil

Contract H0177044 included three objectives; (1) consolidate, maintain, and distribute information on STE approved lighting systems; (2) develop and present one-day seminars on underground mine lighting; (3) determine direct labor and hardware costs associated with the installation of mine illumination systems. All objectives were completed with results as follows: Task I - A file containing 1350 Statements of Test and Evaluation (STE) for all types of underground equipment was developed and publicized throughout the coal fields, A total of 40 requests for STE information was received and processed. Task II and III - A series of 50 seminars was scheduled and presented to 942 attendees throughout the coal fields. The seminars were well received and attendees indicated the information presented would be helpful in bringing their equipment into compliance. Holding a series of seminars in the coal fields, instead of a few in population centers, was favored by attendees. Task IV - Installation cost data obtained on 415 lighting systems indicate that the factors which most affect installation costs are higher hardware cost for DC powered systems and slightly higher manpower requirements for systems installed underground. Based on these data, the total cost to industry of retrofitting existing underground equipment could range up to $50 million.

Jan 1, 1979

By Jr. Koch

As a part of a larger study of the distribution of metals within ore deposits, the geometry of distribution of gold, silver, lead, copper, and zinc in five veins of the Fresnillo mine, Zacatecas, Mexico, was established. The purpose was to obtain basic data necessary for evaluation of geological theories about processes of vein formation and useful for practical mining applications in ore estimation and prediction of ore beyond present workings. The Bureau of Mines investigation comprised statistical analysis of 64,000 assay values from some 16,000 mine samples. The samples were taken at 2-meter intervals in drifts exposing the veins through a vertical range of some 750 meters. Within individual veins, the metals are distributed in dome¬like patterns with highest metal contents tending Lo occur in oreshoots at the centers of the developed parts of the veins. However, in the block of ground containing all five veins, base metals define mathematical domes with highest contents near the center; precious metals define mathematical basins or troughs with low contents near the center. The ratio of silver assay values to lead assay values corresponds to two geographically distinct types of mineralization: one in which silver is closely related to lead, and another in which silver is independent of lead. Other metal ratios also vary regularly from one place to another. The statistical methods employed in this study would be useful for other geologists or engineers who need to analyze large amounts of assay or similar numerical data.

Jan 1, 1967

Auger operations produced 14 million tons of coal in 1974, or approximately 5% of all surface mined coal. It was the most efficient of all coal mining methods, producing 40.0 tons per man-day. Exhibit 1.1 gives a breakdown of productivity of all coal mining methods. Exhibit 161 PRODUCTIVITY OF COAL MINING METHODS (Short tons per man-day) [Method - 1971 1972 1973 1974 Conventional 11.00 10.00 9.75 9.30 Continuous 13.00 12.50 12.25 11.90 Strip Mines 35.69 35.95 36.00 36.00 Auger Mines 39.00 43.00 45.33 40.00 ] Unlike other surface mining methods, augering produces clean coal, largely uncontaminated by foreign materials, other than those existing in the coal seam itself. However, compared to other methods, the coal recovery rate is relatively low. For example, a triple-headed auger in a 35-inch seam would recover approximately 50% of the coal in the seam as compared to a 90 to 95% recovery rate for strip mining and a 55 to 65% recovery rate for deep-mining. The low auger recovery rate is due to the circular cuts and pillars left in the seam.

Jan 1, 1975

By B. M. O'Harra

Zinc smelting is frequently termed a ba.ckward art. The term is hardly true, for great progress has been made in recent years in the design and in the thermal efficiency of the retort furnace, in the quality of retorts, in the recovery of zinc, and in the ability to treat more impure and complex ores. The fact remains, however, that the peculiar physical and chemical properties of zinc have delayed such immense advances-large smelting units, high recovery, lowunit costs, and ability to treat low-grade ores-as have been made in the metallurgy of lead and copper. In current retort-smelting practice, the ores, if carbonates, are calcined to remove carbon dioxide; or, if sulphides, are roasted to remove sulphur. The sulphur must be eliminated as completely as possible, usually to less than 1 per cent. This means that the roast must be continued for a long time at a high temperature, with resulting high cost and small capacity per furnace. The roasted ore is mixed with about 50 per cent of its weight of reducer, which may be fine coke, anthracite, or nonbituminous coal. This mixture is charged into horizontal fire-clay retorts. The retorts used in this country are about 8 inches in internal diameter by 4 feet in length and hold 50 or 60 pou~ds of ore. The diameter of the retort is limited by the tirrie required for the heat to penetrate to the center of the charge; the length by the strength of the retort, which at the high temperature employed can not support the weight of the charge if the span is more than about 50 inches. The retorts are heated externally by coal, natural gas, qr ·producer gas to a temperature of 1,200° C. or more. The zinc oxide is reduced to zinc, which is volatile at this temperature, and passes into a conical fire-clay condenser. attached to one end of the retort, where it conde_nses to liquid zinc and is removed. Twenty-four hours are required for distillation, and because of the low heat conductivity of the retort walls 11.nd of the ore charge itself, the heat efficiency even of the most modern regenerative furnacei;; is only about 12 per cent. The retorts have a short life, 30 to 6Q days, at the high temperature required-; zinc losses are heavy, usually 10 per cent or more; and the proportion of impurities in the retort charge must be carefully controlled to prevent the rapid corrosion of retorts. For these reasons, much work has been done in an e:ff ort to, find cheaper and more efficient methods o.f recovering zinc from its ores. Various methods have been proposed for smelting in the blast furnace. Some of these contemplated the production of zinc vapor and its condensation to liquid; others attempted to produce liquid zinc directly by smelting under pressure. It is now realized that fundamental difficulties render these proposals impracticable. The electric furnace for smelting offers obvious advantages in the way of the efficient utilization of energy, large units, easy attainment of high temperatures, and the possibility of treating complex ores. E. H. and A. H. Cowles first suggested a design for an electric furnace for the reduction of zinc ores and patented their process in 1885. Their attention was soon directed to other uses for their furnace and nothing further of importance was done in the electric smelting of zinc until about 1900. Several investigators then started work upon various processes and had more or less success. The chief difficulty they encountered was the impossibility of obtaining more, than a small amount of the zinc as liquid metal because most of the zinc vapor condensed as blue powder. Interest in the electrothermic metallurgy of zinc increased, many patents on processes and furnace design were taken out, and the literature on the subject grew, until in 1914 and 1915 the problem seemed to be approaching solution. About this time the hydrometallurgy of zinc, the development of which had been lagging somewhat behind that of the electrothermic metallurgy, sprang into the limelight and a commercial process was soon perfected. This rapid development, perhaps aided by the war premium on the high-grade spelter produced by electrolytic deposition, distracted attention from electric smelting to some extent, though progress continued. With the perfection and standardization of the electrolytic process has come a better realization of its limitations, especially the necessity for large-scale operation ·and the difficulty of obtaining high extraction. Because of these limitations the electrothermic metallurgy of zinc still has a field of its own and in fac-t promises to become a strong competitor of both hydrometallurgy and retort smelting except under conditions highly favorable to the latter methods. Because of the imperfections of the retort and electrolytic processes and the promise that the electric furnace offers in overcoming these imperfections, the. United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, has undertaken a study of the electrothermic metallurgy of zinc.

Jan 1, 1923

By J. W. Howland

To determine their effectiveness in different climate and soil conditions, a demonstration of dozer blades specifically designed for recontouring mine spoil was conducted at an East Texas surface coal mine. The specialized equipment included a 48-foot angle blade, a modified 24-foot "U" blade, a 13-foot deep "U" blade, and a 24-foot grading bar. Both the 4b-foot and the 24-foot "U" blades were mounted in a two-tractor, single-operator configuration. To meet flotation problems common in this mining region, a 22-foot lightweight blade was developed and demonstrated for use on a 400-430 hp tractor. The demonstration involved 1,185 acres and showed a 50% reduction in reclamation costs and a 47% reduction in fuel requirements for this mine site over conventional equipment. Improved equipment, trained operators, good supervision, and improved monitoring techniques contributed to the savings. Procedures and results of the demonstration are presented and analyzed here along with guidelines for application of findings.

Jan 1, 1981

By Larry Patts, Jon Hummer, Jim Noll, Aleksandar Bugarski1, George Schnakenberg, Steve Mischler, Mike Crum, Shawn Vanderslice, Rick Anderson

This study is organized under the auspices of the Metal/Nonmetal Diesel Partnership formed by the National Institute of Occupational Safety and Health (NIOSH), the National Mining Association (NMA), the National Stone Sand and Gravel Association (NSSGA), the United Steel Workers of America (USWA) and the MARG Diesel Coalition. The ultimate objective of the study is to reduce the exposure of underground miners to diesel particulate matter (DPM) and gases, and to help in fulfilling the partnership’s goal of identifying technically and economically feasible controls to curtail particulate matter emissions from existing and new diesel powered vehicles in underground metal and nonmetal mines. The majority of current knowledge on the performance of the diesel particulate filter (DPF) systems and other control technologies is based on studies done under laboratory conditions, the results then being applied the results to on-highway vehicles. According to the best knowledge of the authors, only two comprehensive studies that were conducted recently at Noranda’s Bathurst Mining and Smelting Mine and International Nickel Company’s Stobie Mine under the sponsorship of the Diesel Emissions Evaluation Program [McGinn 2001, Bugarski and Schnakenberg 2001, Bugarski and Schnakenberg 2002] offered some insight into the problems associated with the deployment of modern DPFs to underground mining vehicles. The U.S. mining industry has expressed concern that this rather limited knowledge base is not sufficient to help them comply with the rule limiting DPM exposure of underground metal and nonmetal miners [30 CFR 57.5060 2001]. The partnership agreed that a series of comprehensive field evaluations of DPFs in several underground mines was needed to determine their viability of DPF systems and establish confidence in their performance. The first in this series of studies was the one conducted in Stillwater Mining Company’s Nye Mine, Nye, Montana. This study was conducted in two phases. The objective of the first phase was to establish the effectiveness of the selected technologies in reducing diesel emissions by using an isolated zone methodology. The objective of the second phase was to assess the effectiveness of diesel particulate filters in controlling the exposure of underground miners in actual production scenarios. As part of the first phase of the study a series of tests were conducted at Nye Mine from May 19, 2003 until May 30, 2003. The results of Phase I of the study are presented in this report.

Jan 1, 2005

A major highlight of Fiscal Year 1993 is the completion of a new research facility dedicated to the advancement of robotics research and development. This new facility brings to the U.S. Bureau of Mines one of the largest and most unique facilities of its kind in the world. Located at the Bureau's Pittsburgh Research Center, the facility consolidates under one roof, all of the resource requirements of a first class automation and robotics research program. The Mining Robotics Development Center (MRDC) is the result of a major renovation of a large under-utilized warehouse-type structure and brings together the laboratories and offices previously housed in five separate buildings scattered throughout the Pittsburgh Research Center's 238-acre site. This new facility will support the computer-assisted mining research program, a high priority, multi-million dollar program that is expected to have a high impact on the health and safety of miners and coal productivity.

Jan 1, 1993

By Daniel R. Babich, Jeffrey R. Vipperman, Eric R. Bauer

Prolonged exposure to loud noise can cause permanent damage to the auditory nerve and/or its sensory components. Despite regulations and efforts by government and industry to reduce noise-induced hearing loss (NIHL), it is still a problem in the U.S. coal mining industry. The Mine Safety and Health Administration noise standard (30 CFR3 62), which was enacted in September 2000, is aimed at reducing NIHL in the mining industry. To address NIHL in various aspects of coal mining and provide the necessary information to effectively implement control technologies, the National Institute for Occupational Safety and Health conducted a cross-sectional survey of noise sources and worker noise exposures. Noise surveys consisting of full-shift worker noise exposure (dose) determination, time-motion studies (task observations), and equipment and/or area noise profiling were completed in 8 underground coal mines, 10 surface coal mines, and 8 coal preparation plants. The studies revealed that more than 40% of all workers monitored were subject to noise exposures above 90 dBA TWA8. A summary of these studies is presented, their application to administrative and engineering controls is discussed, and exposure reduction methods are reviewed.

Jan 12, 2006