Search Documents

By Pedro Lilienfeld

This report describes a program whose objective was to develop, design, fabricate and laboratory-test two prototype instruments capable of real-time selective detection and measurement of airborne fibrous-shaped particles. The operation of this fibrous aerosol monitor (FAM) is based on the rotation imparted to the acicular particles by means of a rotating quadrupole electric field of the order of 3000 V/cm. This field induces a dipole charge separation on the fibers and aligns them with the applied field. The selective detection of the fibers is effected by synchronous detection of the resulting modulation of the light scattered from a continuous-wave helium-neon laser beam by the rotating particles. The theory of operation, design of the electric-optical detection configuration and the electronic signal processing method are discussed. By means of a scattering pulse sharpness discrimination technique, fibers whose length exceed a selectable value are detected and their number concentration digitally displayed. Counting times of 1 to 1000 minutes permit the measurement of fiber concentrations between 0.001 and about 30 cm-3. A concentration of the order of one fiber per cubic centimeter can be assessed within a relative standard deviation of 10 percent with a counting period of 10 minutes. The FAM is a portable, battery-powered instrument capable of operating continuously for about 4 hours between battery charges. Preliminary tests with crocidolite and crysotile asbestos as well as with glass fibers were performed in the laboratory and the results indicate good correlation with the standard NIOSH phase contrast microscopy filter counting method.

Jan 1, 1977

This field guide is designed for use in planning pollution control and reclamation activities on small sand and gravel operations. Its purpose is to assist operators in selecting environmentally desirable pollution control and reclamation procedures based upon their particular mining situation. The guide includes information on interpreting physical and cultural factors that must be considered in planning and implementing a mining and reclamation program, achieving environmental protection objectives, and improving community/industry cooperation. Included as appendices are a summary of state laws and a list of additional readings on the subject.

Jan 1, 1981

By D. T. Holmes, W. G. Sandell

"INTRODUCTION Three representative lots of ore wore obtained from the Aguila minim district in Arizona during the Bureau's exploration of manganese deposits there. Since only selectively mined ore from this district will meet commercial-grade specifications, the ores were studied to determine their amenability to concentration.Although the purpose of the investigation was to determine the possibilities of the district as a source of commercial-grade manganese, testing was sufficiently comprehensive to indicate the response of the ores to several different types of treatment. Many data of secondary importance have been omitted, end only the more pertinent tests are presented in detail.At the beginning of the investigation of manganese-ore beneficiation in December 1940, the only product marketable to. Metals Reserve Company was ferro-grade manganese, grade B, the requirements for which follow: Mn, min., 48 percent; Fe, max., 7 percent; Si02, max., 10 percent; P, max., O.18 percent; Al12O3, max., 6 percent; Zn, max., 1 percent.Later the specifications were modified gradually. As of May 15, 1943, manganese products were acceptable if they contained over 35 percent manganese and less than 3 percent zinc and 1 percent phosphorus. Prices were based upon material containing 48 percent manganese, 6.O percent iron, and. 11 percent silica plus alumina. Premiums were paid for manganese con¬tent over 48 percent and iron content under 6 percent, penalties being imposed upon products containing loss than 48 percent manganese or more than 6 percent iron or more than U. percent. silica plus alumina.. The specifications for commercial manganese further required that the maximum particle size be 12 inches and that 75 percent of the product be coarser than 20-mesh. Therefore, fine material, such as table and flotation concentrates, had to be nodulized or sintered. In addition, carbonate manganese ores were not acceptable unless calcined.."

Aug 1, 1948

By Horace C. Porter, F. K. OVITZ

The various fuel investigations that were being carried on by the technologic branch of the United States Geological Survey were transferred by law on July 1, 1910, to a new federal bureau, the Bureau of Mines, that was authorized to continue the investigations and make public reports of the results. In consequence of this transfer, the following report is published as a bulletin of the new bureau. The United States Geological Survey had been engaged in analyzing and testing coals, lignites, and other mineral fuel substances under authority given by act of Congress. This work, now centered at the experiment station at Pittsburg, Pa., had its beginning in the operations of the coal-testing plant erected at the Louisiana Purchase Exposition in St. Louis, Mo., in 1904. The results obtained at that plant showed that the work of determining the fuel value of the coals and lignites in the United States with a view to increasing efficiency in their utilization would be incomplete if it did not include systematic physical and chemical researches into the processes of combustion. Hence in its later investigations the Survey carried on such re- searches, concentrating attention on those lines of inquiry which promised results of greatest economic importance. This bulletin is a report on an investigation of the volatile matter in several typical coals-its composition and amount at different tem- peratures of volatilization. As the investigation is still in progress and will doubtless include other coals than those already examined, the bulletin may be considered a preliminary report, stating the prob- lems studied, the methods used, and the results thus far obtained.

Jan 1, 1910

By B. J. Moore

This publication contains routine analyses and related source data for 374 natural gas samples from 24 States and 5 foreign countries. These samples were collected during calendar year 1966 as a part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses of foreign samples contained in this publication represent the first samples received as a result of this expanded program. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Eight previous publications have been made to present the results of 7,244 gas analyses made? by the Bureau of Mines Helium Activity prior to 1966. The first three, Bulletins 486,5 576,6 and 617,7 contain analyses and related

Jan 1, 1967

By J. R. Ruark

Because of the importance of oil-shale reserves the Bureau or Mines resumed research investigations in this field beginning in 1944. The Bureau early decided to build a Large-scale demonstration plant to accomplish the dual purpose of obtaining design data and to produce crude shale oil for refining studies. Two 40-ton-Capacity batch N-T-U (Nevada-Texas-Utah) retorts were completed for this purpose in 1947. After a preliminary operation, the plant was used to investigate process variables of air rate, recycle gas rate, and shale particle size and crude. Correlations obtained from these variables are presented in this report. Researchers concluded that recycle gas was not necessary for efficient operation of the process. Short comings of the batch method of processing the oil shale are pointed out in the report. Several periods of prolonged production operations were carried out. During these periods, the retorts were operated to produce as much crude oil per day as possible. The lifetime operation of the N-T-U retorts was divides into three periods, namely, preliminary operation, process variable study, and production operation. During the preliminary operation, 187 runs were made with a total of 7,596 tons of raw shale used to produce 3,688 barrels of crude shale oil. During the process variable study, 179 runs were made with a consumption of 7,494 tons of raw shale and a production of 4,218 barrels of crude shale oil. The production operation consisted of 554 runs in which 22,457 tons of raw shale was used to produce 12,359 barrels of crude shale ail. The overall total for the lifetime operation of the retorts consisted of 920 runs with a total consumption of 37,547 tons of raw shale and a production if 20,265 barrels of crude shale oil.

Jan 1, 1956

By J. J. Shields

With the increased use of mechanized equipment in mining bituminous coal, production panels are mined out rapidly. To keep current with the rapid completion of production panels, development work must be speeded up also. Although the same type of equipment usually is employed in development as in production places in the same mine, past output per man for development usually was less than from production panels. A study of development practices in 14 mines reveals a tendency toward equalization of the output per man between development and production.

Jan 1, 1957

By Phillip N. Yasnowsky

"In this Bureau of Mines report, the Federal income tax treatment of mineral exploration and development expenditures is summarized, and changes in the tax treatment of these expenditures since 1951 are detailed and analyzed. Although no attempt is made to establish causal relationships, major tax changes favorable to exploration and development activities did occur in 1951 and 1966 when the Nation was engaged in military actions and the economy was expanding. More recent changes have been unfavorable to exploration and development and were parts of major tax reform efforts. INTRODUCTIONThis Bureau of Mines report discusses the Federal tax law provisions relating to mineral exploration and development expenditures. These provisions, contained mainly in sections 616 and 617 of the Internal Revenue Code of 1954 (Title 26 of the U.S. Code), apply specifically to minerals (other than oil and gas), and thus are of interest to the Bureau of Mines.Bureau of Mines involvement in this subject stems from the legislative mandate in the 1913 amendments to the Organic Act of 1910 (the Act creating the Bureau) to conduct economic investigations of the mineral industries. Congressional concern with the financial conditions in the economic and mineral industries was expressed more recently in the Mining and Minerals Policy Act of 1970 and in the National Materials and Minerals Policy, Research, and Development Act of 1980. The General Accounting Office recommended in 1976 that the Department of the Interior ""identify and evaluate laws and agency programs that affect maintaining and developing a sound and stable domestic mining and minerals industry"" (17, p. iii). 2Taxes, a source of revenue to governments, are a cost to private firms. Thus, taxes directly affect private sector profits, and unique tax provisions are designed to encourage (or discourage) activities such as agriculture, construction, or mining. Even the international competitiveness of the domestic mineral industries may be affected by taxes because many minerals are traded in world markets."

Jan 1, 1985

By Edward G. Cunney

Track in underground bituminous coal mines was investigated and technology was taken from other industries in order to obtain information on conditions that impair the safety and efficiency of the track and to develop guidelines and useful information on the construction, inspection and maintenance of mine track. Volume 1 contains information on the investigations, observed track conditions, useful technology from railroads and other industries, derivations of track condition descriptors and limits, conclusions, and recommendations. Volume 2, Guidelines, contains recommended standards and practices for mine track. It includes the relation of track conditions to safe speeds; descriptions and limits for measurable track features, such as gage; descriptions of conditions for track components that are normally not measurable, such as subbase soils; construction requirements and techniques; inspection requirements and methods; and methods for managing and performing track maintenance work. It does not repeat the summary or? derivations. Volume 3, Inspection Handbook, summarizes recommended standards and procedures from Volume II and provides related information for ready reference by inspectors in the mines. As a research product to be used in mines, it does not repeat the summary, derivations or references.

Jan 1, 1977

By John W. Buch

This is the first progress report to be released on the anthracite, mechanical mining research and engineering development program of the Bureau of Mines. This phase of Bureau work, which was initiated as an aid to stimulating wartime production of anthracite, has been continued after the war to assist primarily in improving the general economic position of the anthracite industry. Field work was started in. the 1945 fiscal year with the cooperation of an advisory committee representing management, labor, and the Commonwealth of Pennsylvania. For a beginning, several matters were suggested by members of this advisory committee as being worthy of investigation, and sections of underground mines yore offered for test purposes. Among the suggestions accepted for investigation was the problem of increasing the rate of advance for driving gangways in thin, steeply pitching anthracite beds 4 to 6 feet thick and pitching 60 degrees or more. The problem was undertaken as a field study, and this report relates to accomplishments on this project to June 30, 1947.

Jan 1, 1949

By Dean H. Ambrose

Using three-dimensional (3-0) graphics computing to evaluate new technologies for computer-assisted mining systems illustrates how these visual techniques can redefine the way researchers look at raw scientific data. The U.S. Bureau of Mines is using 3-D graphics computing to obtain cheaply, easily, and quickly information about the operation and design of current and proposed mechanical coal and metal-nonmetal mining systems. Bureau engineers developed a graphics simulator for a continuous miner that enables a realistic test for experimental software that controls the functions of a machine. Some of the specific simulated functions of the continuous miner are machine motion, appendage motion, machine position, and machine sensors. The simulator uses data files generated in the laboratory or mine using a computer-assisted mining machine. The data file contains information from a laser-based guidance system and a data acquisition system that records all control commands given to a computer-assisted mining machine. This report documents the first phase in developing the simulator and discusses simulator requirements, features of the initial simulator, and several examples of its application. During this endeavor, Bureau engineers discovered and appreciated the simulator's potential to assist their investigations of machine controls and navigation systems.

Jan 1, 1992

By Thomas C. Denton

ALL of the 45 political divisions of Africa were accessible to non-Communist world industry and commerce throughout 1964, although in some of them revolt and political attitudes presented problems. The position of the continent as a whole for mineral and mineral fuel resources, production, and oversea exports continued to improve. At yearend, significant quantities of a greater number of mineral commodities vital to industry and agriculture were being produced than in any other continent. This statement excludes Communist areas on other continents but might well hold true even if such areas were included. Deriving from its exceptionally diversified production, Africa furnished overseas industrialized countries as a w ole a greater variety of key mineral commodities than any other area. In addition, the value of mineral imports from Africa into the United Kingdom and continental non-Communist Europe probably exceeded the value of such imports from any other area if gold is included and mineral fuels excluded.

Jan 1, 1966

By John W. Sweeney

Shales and clays from Illinois were sampled, tested, and evaluated to determine feasibility of producing lightweight aggregate by rotary-kiln methods. Sampling procedures and the 1 ,,,y of the Pennsylvanian shale units are discussed. Chemical, X-ray spectrographic and X-ray petrographic analyses were run on the samples to determine if a correlation existed between chemical mineralogic composition and expansion. Preliminary expansion testing was conducted in a muffle furnace. Rotary-kiln tests were conducted in a 16- inch by 14-foot rotary kiln. The weight of the aggregate ranged from 27 to 59 pounds per cubic foot. Concrete cubes employing the aggregate were tested to determine the qualities of the concrete. Compressive strength of the concrete using the 7-bag of cement cement per cubic yard mix, after autoclave curing for 6 hours, ranged from 2,950 to 6,750 psi. No correlation was found between the chemical, X-ray spectrographic, and X-ray and petrographic analyses and expansion, Sixteen samples made suitable lightweight aggregates in the laboratory rotary kiln. The expansion temperature range of eight of the samples was extremely narrow, and difficulties would probably be encountered in processing these materials commercially.

Jan 1, 1965

By Paul Averitt

The coal-bearing rocks in Iowa occur in an arcuate belt across the central and southern parts of the State (fig. 1) at the northern end of the Western Interior coal field. Coal beds of minable thickness are sporadic throughout this area and are mined principally in the three districts indicated by dark shading on the index map, although coal occurs also in the areas indicated by light shading. The coal is mostly of high-volatile C bituminous rank in all parts of the State. SURFACE FEATURES The coal-bearing rocks in Iowa are concealed for the most part by a covering of glacial drift ranging in thickness from a few feet to several hundred feet. This covering has been dissected to form a gently rolling upland, rising from an elevation of 466 feet at the mouth of the Des Moines River to about 1,200 feet in Calhoun County in the central part of the State. The local relief, however, rarely exceeds 150 to 200 feet.

Jan 1, 1949

"The mission of the Respirable Dust Center is to enhance the health, safety and productivity of the miners 'through advancing the fundamental .understanding of all aspects of respirable dust associated with mining and milling and the interaction of dus.t and lungs for reducing the incidence and severity of respirable dust disease. All Dust Center activities are focussed to be responsive to this mission which is shared by several federal agencies closely associated with the Generic Mineral Technology Center for Respirable Dust such as USBM, M,SHA, and NIOSH, and the mining industry. While significant progress has been achieved in making mine atmospheres cleaner and healthier, respirable dust disease remains the nations worst industrial hazard. GOALSThe goals of the Respirable Dust Center have been formulated to recognize the diverse scientific, engineering and medical aspects of respirable dust as well as the need to enhance the interaction, education and technology transfer in the respirable dust area.The Center goals are to:1. Enhance the understanding of the scientific, engineering and biological characteristics of fine and respirable mineral particles, fibers, organic aerosols, and complex particles found in the mining and milling atmospheres.2. Advance the understanding of the physical behavior of airborne respirable dust particles in flowing streams under different. stimuli during mining and milling.3. Advance fundamental understanding of the causative mechanisms for the occupationally related lung impairments and the airway diseases of mine and mill workers.4. Establish the relationship between natural and cultural factors (mine geology, mineralogy, mining and milling methods, equipment and control measures) in the generation, exposures, and pathogenic properties of fine particles.5. Contribute to the development of control mechanisms for reducing ambient respirable dust concentrations, worker exposure, the incidence and severity of dust related lung disorders and disease prevention in mining and milling atmospheres.6. Enhance functional integration among the various research personnel in the Center, as well as, with other groups, such as MSHA, NIOSH and USBM involved in respirable dust research and control.7. Develop technically trained personnel for employment in the mineral industry for respirable dust research and control.8. Enhance the availability of respirable dust-related information utilizing several technology transfer avenues."

Jan 1, 1990

By J. Sammarco

The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting mine illumination research to determine if light-emitting diode (LED) cap lamps can improve safety by reducing glare. Glare can impede a miner?s ability to see hazards and to safely perform their work. Another objective is to determine if a person?s age is a factor. This is important because the workforce is aging ? the average miner is now about 43 years old. Three cap lamps were used to evaluate glare: an incandescent cap lamp, a commercially available LED cap lamp and a NIOSH prototype LED cap lamp. Thirty NIOSH personnel from the Pittsburgh Research Laboratory (PRL) served as test subjects. Three age groups were established with ten subjects in each group. Testing was conducted in the Mine Illumination Laboratory (MIL) of NIOSH PRL. The results indicate no statistically significant difference in discomfort glare among the incandescent and LED cap lamps. However, an analysis of variance for disability glare indicates that the LED cap lamps were superior for the older subjects. Disability glare scores for the oldest subject group improved 53.8% when using the NIOSH prototype LED cap lamp compared to the incandescent cap lamp and 36.5% compared to the commercial LED cap lamp. It ap­pears that, given the conditions of this study, LED cap lamps will not increase discomfort glare and can enable significant improvements in disability glare for older workers. It is also evident that not all LEDs are created equal. The disability glare improved the best for older workers when they used the NIOSH prototype LED cap lamp, which has a different spectral power distribution (SPD) (more short wavelength energy) than the commercial LED cap lamp. Therefore, for disability glare, the results suggest that the SPD is an important factor to consider in cap lamp design.

Jan 1, 2009

By George S. Rice

The prevention of coal-mine explosions has been one of the chief purposes of the Bureau of Mines. In facti the first Federal appropriation relating to mining methods, in 1908, authorized the investigation of the causes of mine explosions and the possible methods of preventing them. When that investigation started the mining industry had not determined the real causes of a succession of terrible coal-mine explosions in various countries, culminating in the great disasters at CoulTièl'es, France, and Monongah, W. Va. Coal dust as an agent of widespread explosions had been under suspicion, and watering to allay the dust was recommended by some mining engineers but the watering of coal-mine dust was adopted in comparatively few mines of the United States and Great Britain, and had not been introduced widely in any country except Germany. Rock dusting, another method of preventing explosions of coal dust, was early tested with success by the Bureau of Mines in its fist gallery at Pittsburgh and, beginnig in 1911, at the experimental mine, Bruceton, Pa. Several of the fist publications i of the bureau suggested that rock dust be used in gaseous or dusty bituminous mines, and in 1915 Technical Paper 842 strongly recommended it. Since that time additional tests in the experimental mine have fully confied this :ft judgment.

Jan 1, 1924

By Clifford H. Summers

This report describes an experimental program which we conducted on behalf of the U. S. Bureau of Mines, to select from currently available materials two novel systems of construction for air-restraining bulkheads to be used in control of radon-polluted air in underground uranium mines. The program included both laboratory and field tests, the latter conducted in a portion of an operating mine owned and operated by Union Carbide Corporation at LaSal, Utah. The test site was a worked-out, double entry stope having a Volume of about 2000 cubic meters, and was located immediately adjacent to an exhaust airway. The bulkheads were constructed of 15 cm x 1.5 cm timber uprights, 5 cm x 15 cm horizontal members supporting a close-fitted 13 mm plywood curtain-wall., which was covered with a low-permeability membrane to seal in the radon-polluted air. The two membrane materials selected for testing were chosen from a list of twenty-two potentially acceptable candidates using criteria such as strength, flammability, ease of application, adhesion, radon permeability, and elasticity. Thirteen of the candidates were tested in our laboratories for adhesion to plywood and to both wet and dry concrete (simulating wet and dry mine rock surfaces), and for their general physical properties, including radon permeability. The final selections made by the Technical Project Officer, and based on our recommendation, were a pre-formed ethylene propylene diene monomeric rubber (EPDM) membrane 1.12 mm thick, normally used as a roof sealant in industrial construction, and available from Carlisle Tire and Rubber Co., Division of Carlisle Corp., Carlisle, PA, and Aquafas 48-00, a water-based mastic used in a wide variety of commercial applications and available from H. B. Fuller Co., Foster Products Division, Spring House, PA. The EPDM membrane was applied as a single sheet, laminated (dry) between two layers of plywood, and the Aquafas was applied both by troweling and spraying onto a plywood surface. In the field test, radon concentrations were continuously measured before, after, and in the trapped air behind each bulkhead. Temperature, pressure, and velocity of the air in the adjacent airway were also measured and recorded continuously. Radon fluxes at the rock/air interface and through the bulkheads themselves were measured manually on a frequent basis. All continuously acquired raw data were recorded automatically on two USBM Data Aquisition Systems (DAS), and the raw data were converted into engineering units and recorded on magnetic disks by a specially programmed microcomputer that was interfaced with the DAS's. Relatively clean (i.e. low radon concentration) air was pumped into a point near the face of one test bulkhead from a location 170 meters away through vent bag. Several air curtains and two air-restraining bulkheads were erected in passageways adjacent to the test area in an effort to control both velocity and radon concentration of the air flowing past the bulkhead faces. An average concentration of approximately 500 pCi/liter at a flow of 550 m3/minute was attained as the background concentration against which leakage through the bulkheads was measured. The entire field test period extended from October, 1981 to March, 1982, a total of six months, and was subdivided into seven successive time periods: 1) site preparation 2) background measurements prior to bulkhead construction 3) passive restraint, with bulkheads in place and totally sealed 4) open bleeder period of natural convection ventilation in and out of the bulkheaded area through a 10 cm (diameter) opening, with connecting tubing; leading into an Exhaust airway 5) open bleeder period, having forced exhaust through a 1.0 cm opening using a servo-controlled fan 6) charcoal trapping period, using the servo-controlled fan to exhaust air through the charcoal traps, to test the effectiveness of such traps in removal of radon from the exhausted air 7) site decommissioning Each of the two systems tested, one incorporating the pro-formed EPDM-rubber membrane and the other utilizing Aquafas 48-00, was assessed for effectiveness in controlling radon-polluted air by observing the change in the radon concentration in the ventilation air flowing continuously over the surface of each bulkhead. The sensitivity of the observed measurements was limited by the volume flow-rate of the ventilation air and the radon concentration in that air. The data would indicate that the observed increments in radon concentration in the ventilation air moving across bulkheads B-l and B-2 were essentially zero within the limits of sensitivity of the measurements. Data from radon flux measurement taken both on the sealed ribs adjacent to the bulkheads and on the bulkheads themselves did not differ significantly from blank data.

Jan 1, 1982

By T. E. Gray

This report describes the preparation characteristics of the more significant coals in Dickenson County, Va. It is one in a series planned to determine which coals are suitable for the production of metallurgical coke either as mined or after beneficiation. Nearly 4 million tons of coal was produced in Dickenson County in 1955, of which approximately 2.7 million tons was cleaned mechanically in 5 cleaning plants. The Federal Geological Survey has estimated that nearly 1,300 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By P. L. Woolf

Three trials with oxygen-enriched unheated blast air are described. The trials were conducted in the Bureau of Mines experimental blast furnace located in Bruceton, PA. The first trial utilized moisture addition to the oxygenated blast. The second and third trial were conducted with natural gas injection. The test was basically a feasibility study and in that regard the practice was demonstrated to be feasible and also have possible advantages over hot blast operation. The testwork was conducted in 1964 and 1965 as part of a continuing study of iron making technology in cooperation with several North American Steel Companies.

Jan 1, 1985