Search Documents

By D. E. Shanks

The Bureau of Mines surveyed a variety of inorganic ion-exchange materials to determine their suitability for removing valuable accessory elements and troublesome contaminants from metallurgical process and waste streams. Most of the materials, which included molecular sieves, heteropolyacid salts, and hydrous metal oxides, did not give adequate separations, did not have the necessary stability in strong acids or bases, or were not in a physical form suitable for ion-exchange use. Many of the suitable inorganic materials, especially the hydrous oxides, were capable of cation exchange with high capacity only in basic conditions, which caused hydrolysis of most of the cations tested. Multivalent anions, such as arsenate and phosphate, were easily removed from acidic solutions by hydrous oxides. Hydrous zirconia was the best material for this purpose. Multivalent anions were not easily des orbed because of compound formation; therefore, conventional ion-exchange techniques could not be employed. As an alternative approach, hydrous ferric hydroxide was used as a filter material to remove arsenate and phosphate from acid solutions. One gram of arsenic was removed from solution for each 20 g of ferric hydroxide. Ferric hydroxide is preferable to hydrous zirconia for use as a filter material because of low cost.

Jan 1, 1983

By Charles A. R. Lambly

This paper, which describes the mining practices of the Pend Oreille Mines & Metals Co. at Metaline Falls, Wash., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in various mining districts of the United States. ACKNOWLEDGMENTS Acknowledgment is made to L. P. Larson, president, and Jens Jensen, secretary, of the Pend Oreille Mines & Metals Co. for permission to publish this paper. information was supplied by E. Berglund, mine superintendent; Earl Miller, chief engineer; Lynn Kinney, John Currie, and Wally Frick, engineers; Arthur Newman, chief clerk; and Jack Crampton, assayer.

Jan 1, 1941

This Bureau of Mines report is a reference manual of procedures used by the Bureau's Twin Cities Mining Research Center for obtaining rock properties. Included in the report are discussions on the usage of each property, descriptions of the general test methods for obtaining the properties, and instructions for performing the tests. The Instructions embrace details of the specimen configuration, test apparatus, test procedure, test conditions, and calculations needed to achieve satisfactory results. Although the procedures presented in this reference manual generally conform to recommendations of the ASTM Administrative Committee on Standards, they are not purported to be standards.

Jan 1, 1974

By C. F. Ellis

Interest in the composition of automobile exhaust gases has been greatly accelerated by recent studies that have indicated that these gases contribute to smog formation in urban areas. Several analytical methods have been published for the analysis of the hydrocarbons in the exhaust gases, but similar information has not been published on the analysis of the oxygenated compounds. This report presents procedures for chemical analyses of certain oxygenated compounds, procedures for sampling the exhaust gases for these analyses, and the analytical results of some experimental work in which these procedures were used. A stationary 1956 model, 170 horsepower, V-8, dynamometer-mounted engine, operated to simulate vehicular cruise conditions, was used for the study. Exhaust gases produced from a regular-grade Midcontinent gasoline during 15-40- , and 60-mile-per-hour cruise operations were analyzed by chemical methods for formaldehyde, total aldehydes, total carbonyls, total alcohols, carbon associated with the oxygenated compounds, and the oxides of nitrogen. Experimental results indicate: 1. The range of concentrations of the total of the functional groups of oxygenated compounds, expressed as moles per million moles of water-free exhaust gases, is about 90-100; the concentrations increase with engine speed. 2. Aldehydes comprise about 80-90 mole- percent of the total of the oxygenated groups, and formaldehyde accounts for about 50 mole-percent of the total aldehydes. 3. The order of magnitude of the concentration of the carbonyls is the same as that for the aldehydes, indicating that ketones are not a major group. A colorimetric test indicates that methyl ketones Constitute about 2 mole-percent of the oxygenated compounds.

Jan 1, 1961

By G. R. Hopkins

For several years prior to about the middle of 1928 both the number and capacity of natural-gasoline plants showed a steady increase; this resulted from a material gain in the supply of casinghead has due to the discovery of a number of flush fields with relatively high gas-oil ratios. From 1928 to date some form of proration has been continually in force, with a consequent curtailment in the supply of wet gas. This decline in available gas and a severe decrease in prices, due largely to the increasing competition of light refinery products, has eliminated virtually all of the weaker units during the last 5 years, with the result that the number of plants declined from 1,155 on January 1, 1928 to 19035 on January 1, 1930, to 909 on January 1, 1932, and then to 859 on January 1, 1934, The struggle of the small high-cost producers to exist is illustrated further by the trend in the number of shut-down plants, which has increased from 36 on January 1, 1930 to 100 on January 1, 1932 and to 128 on January 1, 1934. The increase in the number of plants prior to 1929 resulted in a material gain in the total capacity, but the decline in number between 1929 and 1932 was not followed by a corresponding decrease in capacity, as gains resulting from the construction of a few very large plants overbalanced the loss due to the dismantling of a large number of small ones. However, the low prices of 1932 and 1933 supplied little incentive for new construction, and the total capacity declined in approximately the same ratio as the number. Thus the total capacity declined from 11,387,000 gallons daily on January 1, 1932 to 13,060,000 gallons daily on January 1, 1934, Of the latter 9,181,000 gallons (91 percent) represented the capacity of the operating plants and 679,000 gallons (9 percent) the capacity of the idle plants.

Jan 1, 1934

By Jon K. Ahlness

The Bureau of Mines investigated technologies for testing the integrity of in situ leach mining wells, as required by environmental regulations. To test for leaks, inflatable packers were used to seal the well casing. Laboratory testing determined that the packers could contain a casing pressure up to 50 to 60 psi (345 to 414 kPa) less than the packer inflation pressure. Single-and double-packer configurations were successfully field-tested in 32 wells ranging from 500 to 530 ft (153 to 162 m) in depth. A rigid pipeline and a hoist truck were used to run the packers in and out of the wells for the double-packer tests, which averaged 2-1/4 h each. In an effort to decrease the time of the rigid-pipe double-packer test. a self-contained trailer-mounted test system was designed and built. It utilizes a winch and steel cable to run the packers in and out of the well and high-pressure nylon tubing for packer inflation. This system was successfully field-tested in eight wells averaging 650 ft (198 m) in depth and resulted in a time savings of 13 pct and an operator-hour reduction of 42 pct.

Jan 1, 1985

By Michael R. Norland

This U.S. Bureau of Mines report on U.S. and Canadian 1iterature pertaining to soil characterization and the use of soil amendments as a part of the reclamation process of coal surface-mined lands contains 1,280 references. The references were published during the 1977 to 1988 period. Each reference is evaluated by keywords, providing the reader with a means of rapidly sorting through the references to locate those articles with the coal mining region and subjects of interest. All references are annotated.

Jan 1, 1991

By Shiro Watanabe

To determine the potentialities of nickel as a substitute for cobalt in catalysts for the synthesis of hydrocarbons from carbon monoxide and hydrogen, RESULTS The maximum oil yields obtained in bench-scale equipment were as follows: Using 100N1:20Mn:100 kaolin:200 diatomaceous earth catalyst, a maximum yield of 133.8 cm.3/m.3 of pure CO+2H2 was obtained from one pass of the feed gas, With a nickel:cobalt mixed catalyst (Ni:Co - 3:7) having the composition 100(Ni+Co):8MgO: 5Th02:200 diatomaceous earth, a maximum of 172.2 cm.3/m.3 of pure C0+2H2 was obtained.

Jan 1, 1951

By H. W. St. Clair

Sampling of heterogeneous mixtures of fused metals or solidified melts is subject to errors not met in sampling finely ground ores or granular materials. These errors arise largely because of the segregation of constituent metals that usually takes place during solidification. It is seldom that a random sample of a lot of metal will represent the composition of the entire lot. The problem becomes especially difficult when it is necessary to make accurate analyses for a segregated impurity present in very small amounts. This paper discusses some of the pertinent experimental observations made in selecting a method for sampling melts of aluminum and zinc containing small amounts of iron and silicon as impurities. Although this experimental study dealt only with sampling this specific combination of metals, many aspects of the study apply generally to any mixture of mol ten metals containing minor constituents that segregate rapidly during freezing of the melt.

Jan 1, 1949

By Ernest W. Johnson

In most underground iron mines in the Lake Superior district the active workings are at considerable depth. When additional openings into such. nines are needed, operating officials are eager to discover more efficient methods of constructing them. In recent years, openings into two mines in the district were made by the borehole method,-which employs chilled-iron shot as the cutting medium. Others were made by the churn-drill method, in which pilot hole is churn-drilled and subsequently reamed to a desired but relatively small diameter. Both methods are comparatively new and unique, at least in some phases and in their application.

Jan 1, 1946

By H. M. Lavender

This paper describing the inclined cut-and-fill, and the semishrinkage methods of mining at the Campbell mine of the Calumet and Arizona Mining Co. at Warren, Ariz., is one of a series being prepared by the United States Bureau of fines on mining methods, practices and costs in the various mining districts in the United States. The major portion of the production from the Bisbee mines of the company is mined by these methods. The total average yearly production for the last two years has been 493,612 tons of 5 per cent copper ore. The average employment in the mining department eras 940 men. With the exception of a small tonnage mined for the high iron and sulphur content, the ore is direct-smelting and is mined for its copper con¬tent and associated gold and silver values.

Jan 1, 1930

By Tim F. Dyson

Feasibility of employing automated processing and detection techniques in the mine disaster communications problem is demonstrated. Efficient processing methods are developed. These methods have been demonstrated both in a laboratory and in a field environment. Evalua¬tion of existing computer capacity is given along with recommendations for expansion.

Jan 1, 1981

By Thomas M. Barczak, Joe Bower, Jinsheng Chen

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water-to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water-solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

By Harold J. Bennett

The purpose of this study was to develop methods for the financial evaluation of mineral deposits. This includes the selection of the best alternative mining and processing methods and production rates. This was done by performing a financial evaluation through computer simulation using sensitivity and probabilistic risk analysis. The criterion used to measure the relative advantages of these investment and operating alternatives is the discounted-cash-flow rate of return. Included is a description of the theory and methods used in the probabilistic analysis approach, which is based on the premise that the expression of a range of values in establishing an estimate for a parameter is more realistic than the choice of a single value. Numerous simulations are made using randomly selected values of the input parameters resulting in a frequency distribution of the rates of return and their relative probability of occurrence. The sensitivity analysis method is described and combined with the probabilistic analysis to interrelate mineral reserves, capital investments, operating costs, and production rates. The ability to vary these input parameters on successive runs has permitted the selection of the best alternative mining and processing methods and production rates for a given mineral deposit. For illustrative purposes the evaluation of a mineral deposit was performed using three alternative mining and processing methods at three different quantities of resources and various production rates and prices. The computer program used in this analysis was written in FORTRAN II for maximum compatability and should run without modification on most computers having BK (8,000-word) core memory, a card reader, and printer (120 characters per line).

Jan 1, 1970

By M. M. Gilkey

This report on water requirements for the New Mexico mineral industry includes data on industrial operations closely related to mineral production. It contains general information concerning public water supplies at five principal cities and a short discussion of water needs for agriculture. Background data are presented regarding the geography, hydrography, and water laws of New Mexico, as well as precipitation and evaporation characteristics of the State. Most of the information on source, quantity, distribution, cost, and treatment of water was obtained in interviews with company representatives. Water systems at 46 operations are illustrated by schematic waterflow diagrams. The study revealed that the New Mexico mineral industry in 1962 used about 16 billion gallons of new water and reused 152 billion gallons, a total usage of 168 billion gallons. Consumption amounted to 7.6 billion gallons. Of the 16 billion gallons of new water, 11.9 billion gallons was "self- supplied" from ground water sources, and 2.6 billion gallons was self supplied from surface sources. Approximately 1.5 billion gallons was purchased. Some of the water from company-owned wells is piped as far as 30 miles. Reported costs of the self-supplied new water range from 1 to 20 cents per 1,000 gallons and average 8 cents per 1,000 gallons for power and maintenance. Inadequacy of the supply of new water at many operations necessitates large-scale recirculation. Reported costs for recirculating water (power and maintenance) average 1.8 cents per 1,000 gallons. For the entire New Mexico mineral industry in 1962, the value of product was $42 per 1,000 gallons of new water intake and $88 per 1,000 gallons consumed. Analyses of 40 water samples, listed in the appendix, show the wide range in water quality at plants throughout the State. Projection of the 1962 water requirements of the mineral industry indicate that the total demand for new water will increase from the 16 billion gallons used in 1962 to 24 billion gallons in 1980, a 50 percent increase; and to 36 billion gallons in 2000, which is 125 percent more than the 1962 intake of new water.

Jan 1, 1965

By M. M. Gilkey

This report on water requirements for the New Mexico mineral industry includes data on industrial operations closely related to mineral production. It contains general information concerning public water supplies at five principal cities and a short discussion of water needs for agriculture. Background data are presented regarding the geography, hydrography, and water laws of New Mexico, as well as precipitatton and evaporation characteristics of the State. Most of the information on source, quantity, distribution, cost, and treatment of water was obtained in interviews with company representatives. Water systems at 46 operations are illustrated by schematic waterflow diagrams. The study revealed that the New Mexico mineral industry in 1962 used about 16 billion gallons of new water and reused 152 billion gallons, a total usage of 168 billion gallons. Consumption amounted to 7.6 billion gallons. Of the 16 billion gallons of new water, 11.9 billion gallons was "self- supplied" from ground water sources, and 2.6 billion gallons was self supplied from surface sources. Approximately 1.5 billion gallons was purchased. Some of the water from company-owned wells is piped as far as 30 miles. Reported costs of the self-supplied new water range from 1 to 20 cents per 1,000 gallons and average 8 cents per 1,000 gallons for power and maintenance. Inadequacy of the supply of new water at many operations necessitates large-scale recirculation. Reported costs for recirculating water (power and maintenance) average 1.8 cents per 1,000 gallons. For the entire New Mexico mineral industry in 1962, the value of product was $42 per 1,000 gallons of new water intake and $88 per 1,000 gallons consumed. Analyses of 40 water samples, listed in the appendix, show the wide range in water quality at plants throughout the State. Projection of the 1962 water requirements of the mineral industry indicate that the total demand for new water will increase from the 16 billion gallons used in 1962 to 24 billion gallons in 1980, a 50 percent increase; and to 36 billion gallons in 2000, which is 125 percent more than the 1962 intake of new water.

Jan 1, 1965

By C. F. Jackson

This paper has been prepared as a progress report in connection with the series of articles on mining methods and costs which are being published by the U. S. Bureau of Mines in the form of information circulars. Then enough circulars have been completed it is planned to publish a more complete and comprehensive paper in bulletin form dealing with the subject of underground transportation. Progress reports, followed by bulletins, will be prepared from time to time dealing with other subjects included in the general study of mining methods at individual mines, such as mine development, drilling, and blasting; stoping methods (each principal stoping method to be summarized in a separate paper); ventilation; wage, contract end bonus systems, etc.

Jan 1, 1930

By W. C. McBee

Technology for the preparation of densifiable sulfur concrete (sulfapave) materials has been devised by the Bureau of Mines. The materials are intended as new construction materials for use in corrosive areas where conventional materials fail. A series of modified sulfur cements were developed, which can be used in combination with dense-graded aggregates to prepare sulfapave materials with excellent corrosion-resistant properties. The materials can be mixed, laid, and compacted into place with conventional hot-mix asphalt pavi.ng equipment. Mixture designs utilizing 5-to 30-pct-modified sulfur cements and dense-graded aggregates gave material properties ranging from rigid to flexible. Laboratory corrosion tests in sulfuric acid showed no material loss or deterioration of physical properties over a 1-year test period in concentrations ranging from 0 to 60 pct at ambient temperatures. Preliminary results on field testing the materials for durability to weathering, corrosion, and traffic have been excellent, with no evidence of failure in the materials.

Jan 1, 1985

By R. W. Huber

A consumable-electrode arc-melting furnace was constructed at the Bureau of Mines Physical Metallurgy Laboratory, College Park, Md., for the production of uncontaminated titanium and titanium-alloy ingots. The furnace was designed to allow for evacuating to very low pressures and back filling with helium and argon mixtures for melting at or near atmospheric pressure. Vacuum melting at a few millimeters pressure was also used with a mixture of helium and argon gas sweeping the crucible. For research purposes a 25- to 30-pound ingot, 4 inches in diameter by 15 inches in length, was selected to provide, enough 1/2-inch plate for extensive tensile and impact testing of standard size specimens. Enough plate was also provided for testing by other Government laboratories. The homogeneity of several alloy ingots was determined, and excellent results were obtained. By using a large electrode-to-ingot-area ratio and high currents or power inputs to the arc furnace rather uniform ingots were routinely prepared.

Jan 1, 1957

By B. W. Gandrud

This report, consisting mostly of float-and-sink data and washability curves, has been prepared in connection with an exhaustive study of coal preparation in Alabama conducted, by the U, S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators On the basis of the float-and-sink data, an attempt has been made to determine approximately the extent of ash and sulphur reduction obtainable under given conditions on coal from the mines which were sampled, In the coal-producing districts of Alabama a great deaf of attention has been given in recent years to the problem of improving preparation methods so as to obtain from various coal beds the best possible grade of washed coal. This is especially so where the washed coal is used for the making of metallurgical coke in by-product plants or where there are possibilities of using the coal for this purpose. In the manufacture of metallurgical coke, the sulphur content of the coal is a very important consideration. It is quite often the determining factor as to whether or not a certain coal can be used for coke making. In the studies which form the basis for this report, all samples have been analyzed for sulphur in order to obtain information regarding the possibilities of sulphur elimination as well as ash reduction, and the samples on which reports are made were obtained from beds that are characterized by rather high percentages of sulphur. In connection with the present investigations of coal preparation in Alabama a standardized method of interpreting float-and-sink data has been used extensively for predicting the ash and sulphur reduction and yields obtainable in a commercial washing plant from various sizes of raw coal and from the raw coal as a whole after a certain degree of crushing. This method, which will be explained in subsequent chapters, was used in interpreting the data contained in this report. The samples used for these washability studies were obtained from the following mines in the Warrior field of Alabama: Beltona mine on the Jefferson bed; Dolomite and Mulga mines on the Pratt bed; Coal Valley No. 163 and Coal Valley No. 11 mines on the Corona bed; Cedar Cove mine on the Carter bed.

Jan 1, 1932