Search Documents

The concept of isokinetic measurement of strength was originally related by Hislop and Perrine.(1)Characteristics of an isokinetic exertion are constant velocity throughout a predetermined range of motion. Strictly speaking, a means of speed control, and not a load in the usual sense, is applied in isokinetic exertions.(1)However, load and resistance are definitely present in this technique. In this case, the load is a result of the energy absorption process performed by the device to keep the exertion speed constant. The device prevents energy from being dissipated through acceleration in isokinetic exercise. The energy is instead converted into a resistive force, which varies in relation to the efficiency of the skeletal muscle. Since the speed of motion is held constant in isokinetic exercise, the resistance experienced during a contraction is equivalent to the force applied throughout the range of motion. For this reason, the technique of isokinetic exercise has sometimes been referred to as accommodating resistance exercise. This type of exercise allows the muscle to contract at its maximum capability a tall points throughout the range of motion. At the extremes of the range of motion of a joint, the muscle has the least mechanical advantage, and the resistance offered by the machine is correspondingly lower. Similarly, as the muscle reaches its optimal mechanical advantage, the resistance of the machine increases proportionally. It must be understood, however, that while isokinetic devices control the speed of the exertion, this does not assure a constant speed of muscle contraction. The speed of isokinetic contractions is constant during individual exertions; however, it is also possible to compare muscular performance over a wide range of isokinetic velocities. Increasing the isokinetic speed of contraction will place increasing demands on Type II muscle fibers (fast twitch and fast oxidative glycolytic). Workplace Assessment It is clear that isometric strength testing cannot substitute for dynamic strength assessment when examining highly dynamic occupational job demands. As most industrial work tasks contain a significant dynamic component, analysis of isokinetic strength capabilities appears to offer some advantage to isometric testing in this regard. However, it must be recognized that isokinetic devices are not entirely realistic compared with free dynamic lifting in which subjects may use rapid acceleration to gain a weight-lifting advantage.

Jan 1, 1998

By Charles Vaught, JON VOLKWEIN, ROBERT PETERS, ERICA HALL

Since 1999, the CWP level among miners with 25 years or more experience, for instance, has risen from slightly more than 4% to 9% (See Figure 1). While it is obviously necessary to protect all miners’ lungs, there is now a technology to improve the chances that new miners’ lungs will be protected from the day they begin work.

By R. P. Vinson

Assessment of workplace exposures is an important tool for helping to minimize dust-related occupational illness and diseases. Real-time particulate monitoring can effectively locate areas where dust controls are needed and determine how well they are working. An affordable, person-wearable, real-time dust monitor is needed. The SKC Inc. Dust Detective (SKCDD) fulfills those requirements (Disclaimer: Mention of any company or product does not imply endorsement by NIOSH). The SKCDD consists of a disposable sampling tube (DST) connected to a small hand-held sampling pump. The SKCDD was developed through a Cooperative Research and Development Agreement (CRADA) between the National Institute of Occupational Safety and Health (NIOSH) and SKC Inc. The relationship of dust concentrations measured by personal gravimetric samplers to those measured by the SKCDD was determined in a laboratory aerosol chamber. A comparison of the means and the relative standard deviation of triplicate measurements of each type of sampling device demonstrated the SKCDD to be a viable alternative means for measuring dust. While it provides accurate measurements for specific coal types, it requires correction factors (those correction factors still need to be calculated) for other coal types.

By R. W. Hiteshue, R. W. Fridy, W. Kawa

A study of the production of coronene , a high - melting ( 440 ° C ) , highboiling ( 525 ° C) , polynuclear hydrocarbon , was made by the Bureau of Mines to determine the maximum yield obtainable by the hydrogenation of coal and coalderived materials . Experiments were made with anthracite and bituminous coals and with asphaltenes and centrifuged residue obtained from heavy oil produced in a pilot plant by the hydrogenation of a bituminous coal at 2,000 psi and 480 ° C. With anthracite , yields of coronene of 0.5 to 0.7 wt pct of moistureand ash - free coal were obtained at 6,000 to 8,000 psi , 700 ° to 750 ° C , and a residence time of 30 minutes . With bituminous coal , yields averaging 0.4 wt pct of maf coal were obtained at 6,000 psi , 800 ° C , and 30 minutes ' residence time . With asphaltene and centrifuged residue , yields of less than 0.02 wt pct of maf coal were obtained at 6,000 psi , 700 ° C , and 60 minutes ' residence time .

Jan 1, 1964

By Ren G. Dong, Dan E. Welcome

Instrumented handles or dynamometers are widely used to measure hand forces and/or the biodynamic response of hand-arm system. To study hand-transmitted vibration exposure, six generations of instrument handles were constructed or initially developed by researchers in ECTB/HELD/NIOSH. This presentation provided a summary of these handles. Their basic characteristics, limitations, and usefulness are described, which may help their appropriate applications and further improvements. Six Designs of Instrumented Handles Handle 1: The conceptual design is recommended in ISO 10819 (1996)1 for glove test. The grip force is measured by detecting bending strains on a measuring beam in the handle. A special handle fixture was designed to connect the handle to a shaker. Except the screws, the handle and fixture were made from aluminum. Handle 2: The design is based on the principle of shear strain measurement.2-3 Both grip and push forces can be measured simultaneously using this handle. This handle was directly designed for a simulated vibrating tool. Handle 3: This design is basically composed of a handle base, a measuring cap, and two charge-based sensors (Kistler 9212) sandwiched between the base and cap. The handle was also made from aluminum. The fixture for Handle 1 was also used with this handle. This generation of handle has three different handle diameters (30, 40, and 50mm).4 Handle 4: This design is an improvement from Handle 3. The handle fixture was totally redesigned and it was much stiffer than the previous one. The aluminum measuring cap was replaced with a magnesium cap. Handle 5: The basic structure of this handle is the same as that for Handle 3. However, the piezoelectric sensors were replaced with two strain gage based sensors (Interface SML-50). Handle 6: This handle includes two measuring caps, four piezoelectric sensors, and a handle centre base. The handle fixture was the same as that with Handle 4. Methods for Handle Examinations The static and dynamic characterizations were performed using the methods reported by Dong et al.5-6 Results and Discussion Handle 1: The static force measurement depended on the hand grip location on the handle. Its natural frequency was less than 200 Hz.5,6 Because the transmissibility of gloves may not vary significantly with the applied grip force, this handle may be acceptable for glove test. However, the force measurements with this handle may not be reliable. Handle 2: The static force measured with this handle was insensitive to the hand acting location. However, when the handle was vibrating, the force signals could be totally distorted. For this reason, it was not used for vibration studies.

Jan 6, 2006

The State of Washington has a federal program that gives the Office of Surface Mining responsibility for assuring the reclamation of lands affected by coal mining. Most of Washington's coal-bearing regions lie west of the Cascade Mountains. The state's coal reserves are estimated at 1.4 billion tons, about 0.3 percent of the nation's total coal reserve. Steeply dipping. minable seams range from 2.5 to 25 feet in thickness. The occurrence of coal in Washington has been documented since the early days of its settlement; at one time, coal production played a significant role in the state's economy. During the late 1800s and early 1900s, coal was second only to lumber in Washington's industrial production. Coal production declined as other sources of energy were developed. By 1959, production was at 200,000 tons. Regulation of the coal mine operations in Washington is conducted by the Office of Surface Mining's Casper, Wyoming, Field Office and its local office in Olympia, Washington. All permit applications and abandoned mine land reclamation are completed by the OSM Western Support Center in Denver, Colorado. Inspections of mine and reclamation sites are conducted by OSM reclamation specialists located in Olympia.

Jan 1, 1992

By Stephen E. Mosher, Suzanne D. Smith

Ground, air, and water vehicles can expose humans to substantial multi-axis vibration. Multiple input/multiple output relationships or models exist for estimating frequency response functions of linear systems1, 2. These relationships have been applied by some investigators to evaluate the effects of occupied seat vibration3, 4. Using a multiple input/single output model, this study investigated the effects of single- and combined-axis vibration in the fore-and-aft (X), lateral (Y), and vertical (Z) directions on vibration transmission to the human chest. Frequency response functions (transmissibilities) were estimated and compared for the back-on and back-off postures. Methods A rigid seat with seat back was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). A flat acceleration vibration signal was generated between 2 and 40 Hz at 1.0 ms-2 rms in the single and combined X, Y, Z, XY, XZ, YZ, and XYZ axes. The signals were shifted in time so that the combined inputs were not fully correlated. Lightweight triaxial accelerometers were used to measure accelerations at the seat base (input) and at the bony manubrium of the chest (output). The maximum of nine frequency response functions (H(?)) or transmissibilities were estimated from the auto- and cross-spectra. The system transfer matrix for the XYZ inputs and chest Z output is [ ] where PxZ, PyZ, and PzZ are the cross-spectra between the three inputs at the seat base and the Z output at the chest, respectively, and Pxx, Pxy,…zz are the auto- and cross-spectra between the input signals (? not shown in Eq. 1). Equation 1 can be similarly written for the chest X and Y outputs. Matlab® was used to estimate the auto- and cross-spectral densities for calculating the transmissibilities, ordinary coherences (for single inputs), partial coherences, and multiple coherences. Results Figure 1 illustrates the major chest transmissibilities observed for the two postures. Vertical vibration showed a consistent influence on the chest X response (Chest X/Z), most likely causing chest pitch. Some chest Z responses were observed with X-axis inputs, but the results were variable and difficult to interpret. In general, other factors besides the known inputs did not affect the transmissibilities shown in Figure 1 (Repeated Measures ANOVA, P<0.05). This was

Jan 6, 2006

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

By Charles L. Kimbell

On the basis of world production data alone, 1985 appears to have been a year in which the world&apos;s mineral industry took another step upward in its recovery from the very poor years of 1981, 1982, and early 1983. Despite a drop in the output of crude oil, which was the single most significant crude mineral product from the viewpoint of value, the estimated value of world crude mineral production advanced by 3.4% to about $1,054 billion constant 1983 dollars, with output increases logged for nearly two-thirds of the commodities and forms of commodities for which the U.S. Bureau of Mines calculates a total world output. However, the economic well-being of any industry or group of industries cannot be measured solely in terms of the volume and/or value of its production, and examination of statistics reflecting other aspects of mineral industry performance shows that 1985 was a less than ideal year in many respects. In the case of consumption of mineral commodities, although there were gains registered in diverse sectors such as iron and steel, aluminum, fertilizer materials, solid fuels, and gaseous fuels, there were also proportionally small but notable declines in use among the older major nonferrous metals (copper, lead, tin, and zinc) and in the all-important liquid fuels. In the case of international trade in mineral commodities, although comprehensive data for 1985 were not yet available, there were indications that the value may well have fallen below the estimated 1984 level of $632 billion, although the volume may have increased slightly. This, if true, would be chiefly the result of declining prices of mineral commodities, and indeed, price declines were noted for a number of significant materials in terms of current dollars, and even more would register declines if calculated on the basis of constant dollars, adjusting for inflation.

Jan 1, 1987

By Charles L. Kimbell

Virtually every available measure of total world mineral industry activity demonstrated that 1982 was little, if any, better for the industry than 1981 had been. Levels of production, trade, and consumption for virtually every major commodity declined; unit prices for most commodities fell, particularly in terms of constant dollars, and as a result of cutbacks in output and lower prices, capital available for investment within the industry was reduced. These conditions, coupled with the existence of considerable idle capacity, tended to retard investment, although there was an upturn in U.S. oil industry investment overseas. Despite the overall depressed situation of the world&apos;s mineral industry, there were indications of possible improvements in market economy countries near yearend, as output of some materials increased marginally and as prices for some mineral commodities reversed their downward trends. The downturns in total world mineral industry activity were not universal from the viewpoint of individual countries. Indeed, output of a number of commodities increased in centrally planned economy countries, and these gains were insufficient to offset declines in market economy countries, thereby sharply altering the proportion of total world output accounted for by each of these two groups of countries. There was a similar shift in consumption on a percentage basis.

Jan 1, 1984

By Naoki Hosoya, Setsuo Maeda

This paper addresses establishment of an experimental system for measuring biodynamic response (BR) of hand-arm system at the NIIH in Japan. BR measurement system at the NIIH is nearly equivalent to NIOSH installed system. The feasibility of the system is examined through the apparent mass (AM) measurement of the empty handle and a set of calibration masses. Apparatus The grip force was measured by using the handle shown in Fig. 1. The handle has two force sensors (KISTLER, 9212) and one accelerometer (PCB, 356A12). A low-pass filter with 5 Hz cut-off frequency was used to the grip force from measured force signal. Figure 2 shows BR measurement system in this study. The push or pull force at the handle was measured by using the force plate (KISTLER, 9286AA). The grip force and the push / pull force were displayed on a monitor. The shaker (IMV, VE-100S) is used to vibrate the hand-arm system along the forearm axis (Zh direction) (ISO 10068, 1998; ISO 5349-1, 2001). In most situations force actions for operating tools are expressed by grip, push, pull and combined these actions. These actions can be simulated in the test system. AM was obtained by performing H1 estimator in the PULSETM system (B&K, 3109) and it is denoted at the one-third octave band center frequencies. [ ] Methods In order to investigate the reliability of the system, AM measurement of the handle was performed. It is assumed that the handle is rigid in the upper limit of adoptive frequency range in this study. This assumption is validated in AM measurement of the empty handle. A pseudo-random vibration in the frequency range of 10 to 1,250 Hz was used and its amplitude is 1.0 (m/s2)2/Hz with a flat power spectral density (PSD) in the experiment. Measured AM includes the mass effect of the measuring cap in a subject experiment. Compensated apparent mass AMc(?) is obtained by Eq. (1) 1-2.

Jan 6, 2006

These proceedings consist of an overview of the underground metal and nonmetal mina fire protection research currently being conducted by the Bureau of Mines. The following papers address the areas of prompt, reliable fire detection, fire planning and warning, fire suppression, and personnel protection. Selected topics are included here that cover fire protection systems for shafts, underground fueling areas, and mobile underground mining equipment; spontaneous combustion, improved stench, and product-of-combustion fire warning systems; computer-aided ventilation modeling; fire doors; and an investigation of fire hazards in mine timbers. The projects described provide a current documentation of problems being addressed.

Jan 1, 1981

By P. -E. Boileau, P. Marcotte, Y. Aldien, S. Rakheja

A number of biodynamic models of the hand-arm system have evolved on the basis of measured driving-point mechanical impedance (DPMI) responses to facilitate analyses of the coupled hand-tool system [1]. The parameter identifications in such models are based upon minimization of an error function of the model and the target impedance data, which may not yield a unique solution. Consequently, a number of model structures and parameter sets could be realized that would equally satisfy the target curve. Moreover, the vast majority of the reported models exhibit acute deficiencies due to excessive static deflections of model masses, presence of a low frequency mode and very light masses in the order of 1.2- 4.8 grams. The models also do not characterize the dependency of the biodynamic responses on many factors, namely the hand forces, hand-arm posture and vibration intensity. This study aims at development of a hand-arm biodynamic model with considerations of the hand forces, and both the DPMI and power absorption measures, to enhance the uniqueness of the model. Methods Two different model structures are chosen for identifying the model parameters on the basis of measured DPMI and absorbed power characteristics of the hand-arm system under zh-axis vibration over a range of hand-grip and push forces. Owing to the strong influence of the hand-handle coupling forces, the models were initially derived for fixed hand forces, namely 30 N grip and 50 N push forces, as suggested in the ISO 10068 standard [2]. The equations of motion for the model are formulated and solved to compute both the DPMI and absorbed power responses. A constrained minimization function comprising weighted errors of both the DPMI and absorbed power is formulated and solved to identify the parameters. Alternate functions corresponding to different combinations of hand forces are then applied to identify hand-force dependent model parameters. Variations in the model parameters are investigated as functions of the grip, push and coupling forces through linear regression analysis. Regression-based models are formulated for deriving the hand-handle forces dependent model parameters. The validity of the model is also examined under selected combinations of hand forces. [ ]

Jan 6, 2006

By Heather N. Dougherty

In the absence of values for each influencing parameter and a known relationship of input-output space, novel approaches should be implemented as proxy solutions to mathematically complicated problems. Proxy solutions can be in the form of linear or non-linear multiple regression equations. Predicting the performance of gob gas ventholes is one of these mathematically complicated problems as it is difficult to know the exact relationships between various parameters influencing gob gas venthole (GGV) performance from active and sealed (completed) longwall panels. In this paper, a discussion of the NIOSH-developed software suite for methane control and prediction (MCP) based on an artificial neural network (ANN) is presented. The application of the ANN-based software suite to develop algebraic relationships for gob gas venthole performance prediction in sealed and active longwall panels is sought. Output information obtained from the NIOSH-MCP software as a response to various input parameters were used to create an input-output database for total flow and methane percentage from GGVs operating in active mines during completed and sealed panel situations. Due to the multi-variable nature of the software, outputs generated using the software for various inputs were used to develop analytical equations first using linear and then second using non-linear multivariable regression techniques. The advantage of this method is its ability to better understand the significant parameters of the relationships between the inputs and outputs for gob gas venthole production in active and sealed panels and to be able to predict their performances using relatively simple analytical functions.

Jan 1, 2010

By Alan Mayton, Bertrand Valero, Farid Amirouche

Handling of heavy vehicles such as tractors, trucks and buses require a large roll stiffness which causes large high accelerations at the seat level during impacts. To provide comfort and minimize the energy transfer from the chassis and the seat a pneumatic active seat suspension is proposed. An active seat suspension design and control algorithm under development at the University of Illinois at Chicago, UIC, is being developed and tested. Preliminary results are presented in this paper. The design of a passive suspension typically consists of optimizing the value of two parameters: the stiffness and the damping of the suspension. The general dynamic performance of the suspension is limited to the conditions under which these parameters were obtained. A change in the input conditions might lead to poor suspension and an amplification of the vibration transmitted to the body. The focus of this paper is a robust, semi-active suspension system with a variable controlled damping and using the body response an index measure to minimize the acceleration at the interface of the seat and operator. A summary of existing suspensions, such as MR and ER fluids, and spring loaded and dual valve shock absorbent will be discussed to highlight the need of a semi-active pneumatic suspension system design. Methods A model of the proposed suspension was developed in MATLB (Simulink) and different control strategies for the valve position in relation to the cylinder pressure tested. The effects of stiffening and softening resulting from pressure changes in the cylinder were examined. The vertical accelerations of the seat was computed for different control strategies and configurations of the suspension and compared to the response of a passive seat suspension. A lump -mass model was created to represent the human body including the head, the upper, middle and lower torso as well as the legs. The connective forces between body segments were modeled through modal analysis techniques from previous experiments at the Vehicle Technology Laboratory. ISO standards and absorbed power were used to evaluate the different configuration of the seat suspension system in relation to the dynamic response of the operator. Results Initial results of the semi-active suspension system show a significant reduction in the RMS value of the acceleration of the seat. A reduction of the total absorbed power by the operator is expected to provide an insight into the control strategies adapted in the active suspension.

Jan 6, 2006

In 2005, a total of 739 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). These mines (e.g., potash, gypsum, salt) comprised 5.0% of all operations. ? Mines producing common clay comprised 26.9% (n=199) of all nonmetal mining operations. ? Nonmetal mining operations were located in all states and territories except Alaska, Delaware, Hawaii, Maine, New Hampshire, Rhode Island, Puerto Rico, and the Virgin Islands.

Jan 1, 2008

By Stephen C. Tadolini, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990’s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine’s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

By Michael J. Beus, Stephen Iverson

BACKGROUND A mine shaft is the lifeline to underground mines. Mine operators depend on safe, uninterrupted, and efficient movement of workers and materials. The shaft and hoisting system provides access to the network of openings used to recover the underground resource, provides vertical transport of miners and materials, and serves as an escapeway in case of an emergency. Accidents involving hoisting can be catastrophic. Such was the case in 1973 at the Markham Colliery in Derbyshire, UK when the conveyance overwound and fell to the shaft bottom, resulting in 17 deaths. Hoist and elevator machinery must meet the requirements specified in the Code of Federal Regulations (CFR), Parts 57 and 75. According to the Mine Safety and Health Administration (MSHA) data, many shaft-related accidents in the United States are associated with the hoisting cycle. MSHA statistics show that there were about 1500 shaft- related accidents in the 5-year period between 1992-1996. Most of these accidents resulted from the action, motion, or failure of the hoisting equipment or mechanism and involved movement of the conveyance which includes cages, skips, ore buckets, and elevators. A hoisting hazard may be characterized as an "unsafe hoist operating condition caused by insufficient or inaccurate information available to the hoist operator" (authors&apos; quote). Earlier investigators have defined safety features and operating and maintenance standards for hoists, and reported on monitoring and control systems and sensors for hoists and conveyances [Farley, 1983; Ward, 19931. However, despite the considerable technological progress and hoisting control improvements in recent years, safety- related issues that require further investigation still remain. The hoist operator must constantly be aware of two important hoist-operating conditions: the position of the conveyance and the tension in the hoist rope. If this information is not available or is inaccurate, the hoist becomes unsafe. Current technology provides this information indirectly from sensors and indicators in the hoist room. However, unlike a building elevator hoistway, mine shaft hoistway problems often include: 1. poor ground conditions and excessive shaft wall and guide displacement; 2. rock bursts in deep mines (resulting in large rock movements and fragments blocking the hoist way); 3. water, ice, and salt buildup (impeding the smooth flow of the conveyance); 4. severe vibration from hoisting (resulting in loose guide support brackets, broken welds, or other alignment and conveyance mechanism malfunctions). The second issue relates to dynamic rope loads applied during normal winding, particularly during loading, acceleration, and stopping. Safety factors on wire rope are based on static load. They are artificially high to account for all cases of dynamic loads, even though the total load history on the rope (static and dynamic) during service is unknown. Therefore the tension, and thus the compliance with wire rope load safety factors, is unknown to the hoistman.

By C. M. K. Boldt

Between 1989 and 1991, the greatest number of accidents in surface coal and metal/nonmetal mines involved haulage trucks. In 1995, the most frequently cited factor contributing to the 100 fatalities in these mines was powered haulage. In 1996, over 50% of the 84 Fatalities in mining that year were in surface mining. Because some of the world&apos;s largest mobile equipment is used in surface mines, and this equipment is involved in so many accidents and fatalities, new technologies are needed to alert truck drivers and people in spaces around the truck to the possibilities of collisions.

Jan 1, 1999

During development mining, ventilation capacity may decrease and the ventilation requirements may depart from initially planned values depending on the mining rate, increases in the methane emission rate, and changes in ventilation airway leakages. Insufficient ventilation air quantities and the occurrences of high methane liberation rates can overwhelm the existing quantity of ventilation air and result in elevated levels of methane gas during development mining. This condition can both limit the development of that section and increase the risk for an ignition that may lead to an explosion. Thus, the prediction of ventilation air requirements prior to mining can enhance worker safety by reducing the likelihood that explosive methane-air mixtures form. This study presents an approach for prediction of methane inflow rates using coalbed methane reservoir modeling. For this purpose, a two-phase coalbed reservoir model of a three-entry type roadway is developed. In the model, grids are dynamically controlled to simulate development of entries. Examples are given for methane inflow and ventilation air requirements as a function of mining rate, development section length, mining height, and the existence of degasification boreholes. This technology can be used to limit the methane concentrations occurring as a result of the influences of various coalbed and operational parameters.

Jan 1, 2008