Search Documents

By E. C. Perkins

As part of a program for developing methods of using domestic titanium deposits, the Bureau of Mines investigated methods for chlorinating titanium slags prepared from titaniferous minerals by electrosmelting. Titaniferous slags were made from ilmenites in the following deposits: Valley County, Idaho; Trail Ridge, Fla.; Aiken, S. C.; and Maclntyre, N. Y.; titaniferous magnetite from Iron Mountain, Wyo., were also evaluated. The tests were made in two chlorinators, a 4-inch and a 36-inch unit. Preliminary testing was done in a 40-millimeter bench-type unit. Chlorine gas was contacted with a loose mixture of titaniferous slag and carbon at a high temperature to form titanium tetrachloride. The moving-bed system used in this work involved a downward movement of feed countercurrent to the chlorine flow, and residues continuously removed from the bottom of the reactor. The performance characteristics of these slags depended on their composition, which varied widely according to the geographic source of the ore. The results showed that all but two of the slags could be chlorinated as effectively as rutile, converting 70 to 80 percent of the titanium to the tetra-, chloride. The two slags that proved difficult were made from New York ilmenite and Wyoming titaniferous magnetite. These slags contained enough magnesium to cause clinkering, which necessitated that the bed be prematurely withdrawn before more than 70 percent of it could react. The iron content of the slags did not interfere with operating the chlorinators. The data from the 4-inch and the 36-inch units were in agreement on the relative amenability of the slags to chlorination.

Jan 1, 1962

By Terry R. Neumann

During 1984, at the request of the U. S. Bureau of Land Management, U.S. Bureau of Mines personnel conducted a mineral survey of the 28,600-acre South Pahroc Range Wilderness Study Area (NV-050-0132). The Wit derness Study Area is located in Lincoln County, NV, about 900 miles north of Las Vegas. Five mineral properties and two mineralized zones were examined during this study; of these, one mineralized zone, two small prospect pits, and part of two claims are within Wilderness Study Area boundaries. Perlite resources were identified in the study area; however, no significant metallic mineral values were noted at any of the sites. The Wilderness Study Area is dominated by a Tertiary volcanic sequence consisting of an interlayered series of tuffs containing thin beds of volcanic pebble gravel, sandstone, and perlite. At the base of the exposed volcanic section, perlite occurs along a 2.4-mile-long zone that parallel s the study area's northeastern boundary. The perlite is suitable for filtration, insulation, and soil conditioning purposes, Because of prohibitive operation and transportation costs, the estimated 6 million tons of perlite occurring inside the South Pahroc Range Wilderness Study Area are classified as an indicated subeconomic resource.

Jan 1, 1986

By G. W. Jones

In a previous report,6 results were given that showed the amount of natural ventilation in a manhole having a capacity of 74.l cubic feet when the number of ventilation openings in the cover was varied. from no openings to a maximum of 48. The results showed that the ventilation (air changes per day) in the manhole was proportional to the area of the openings in the cover, and also that the number or area of the openings was the factor that chiefly affected the ventilation.

Jan 1, 1937

By R. E. Zane

[The Northwest Experiment Station of the Bureau of lines, in cooperation with the College of Mines, University of Washington, has completed a detailed investigation of the physical and chemical properties of western cokes made or used in the Pacific Northwest, as evaluated by standard methods. 4/ One of the chemical properties determined, to which more or less importance has been attached, was reactivity or combustibility. As no standardized procedure is available, it was necessary to develop a workable method for evaluating this property. The combustibility of coke is usually measured by the formation of carbon dioxide with time at a particular temperature or by the reduction of carbon dioxide to carbon monoxide. Analysis of the resulting gases commonly is required to evaluate the result. The method described in this paper is simple and direct in that the sample of coke or other carbonaceous material is weighed as it burns; the loss in weight and time is indicated by a balance and clock arrangement. Gas analyses are not rewired. Methods similar in principle have been used by Tu, Davis, and Hottel6/ and by Oshima and Fukuda7/ for determining the combustion rate of carbon and for studying the effect of ash on combustion characteristics. Both methods: are more elaborate in procedure and apparatus required than teat described here. Brief the method comprises burning a sample of coarsely grained. coke or]

Jan 1, 1940

The small-scale surface mining operation in northern regions is typically located in a remote, ungaged basin. With the recent increase in the economic potential of mining, the number of small operations is increasing. The year-to-year variability in precipitation in this region under study is of great concern to mine operators. Some years may yield only 5 to 6 inches of precipitation, while others may yield in excess of 15 inches. Such variability makes placer mining operations difficult to plan, since low water years may result in too little run-off for gravel washing and high water years may result in flooding of mining developments. There are no official streamfloaw records in many watersheds in the northern region containing placer mining claims. However, information from other streams permits calculation of an estimated discharge for a watershed under consideration using average flows per square mile of drainage. It is to be emphasized that these are average or expected figures in reality, one water year may be significantly wetter or drier than another. This high variability of annual precipitation is significant in relation to placer operations because of the large quantities of water required for this type of mining. Some operations can not operate in low water years. In the larger watersheds, operations may continue in low water years but at a slower pace because of longer water collecting times. The high variability of available run-off rakes placer mining in many parts of Alaska difficult to plan on a long range because of the unpredictability of water supplies.

Jan 1, 1985

By E. Concha

The concept of an Automated Continuous Explosive Excavation system (ACEE) for the underground mining applications of development drifting and room and pillar mining has been evaluated in comparison with conventional drill, blast and muck operations. The role and possible extent of application as this method was identified. The evaluation examined each element of existing and of proposed ACEE design concepts in a defined mine environment. Step by step procedures were developed to quantify the evaluation process where this appeared feasible. One conclusion drawn was that a system approach to ACEE design is not only feasible but attainable within the state of the art. Several preliminary design concepts were formulated and examined in order to determine what further research or development might be needed to realize them.

Jan 1, 1982

By Anderson Dana

THIS PAPER describing methods and costs of mining and preparing gravel and sand for market at the Port Jefferson plant of the Seaboard Sand and Gravel Corporation, is one of a series of articles on gravel and sand mining, prepared for and published by the U. S. Bureau of Mines, which is designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs, It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical [ ]

Jan 1, 1932

By B. J. Moore

This Bureau of Mines publication estimates that U.S. helium resources as of January 1977 were 710 billion cubic feet. These resources are broken down into four classifications, as follows: Helium in measured natural gas resources and in storage, 201 billion cubic feet; helium in indicated natural gas resources, 150 billion cubic feet; helium in hypothetical natural gas resources, 175 billion cubic feet; and helium in speculative natural gas resources, 184 billion cubic feet.2 Most of the helium in natural gas is presently dissipated as natural gas is consumed as fuel and for other purposes. Helium resources of the United States may also be divided into three other categories: (1) Depleting and undiscovered natural gas resources, 589 billion cubic feet; (2) nondepleting natural gas, 83 billion cubic feet; and (3) storage, 38 billion cubic feet, of which 37 billion cubic feet is federally owned and 1 billion cubic feet is privately owned. The United States does not have any significant leasehold rights in the depleting fuel gas resources. However, through the Department of the Interior, it does have leasehold rights to about 70 percent of the helium found in nondepleting natural gas, and it owns over 90 percent of the helium in storage.

Jan 1, 1979

By I. Liebman

The Bureau of Mines conducted research to develop triggered barrier systems for protection against gas explosions that can occur in underground coal mines during the use of continuous miners. Several extinguishing agents were tested in barriers at a simulated mine face. Water, powered by pressurized nitrogen, was found to be efficient in stopping fully developed gas explosions, but it had little effect against the explosion during its incipient stage. Hybrid combinations of currently known extinguishants, however, were successful against incipient explosions. Three hybrids that were developed and tested consisted of Halon 1301, combined with either an aqueous foam solution, water, or a dry chemical powder. The three hybrids were found to be more efficient than any constituent alone. Results of the tests point to a synergism between the hybrid components, and indicate that the Halon aids in dispersing its constituent and also converts the aqueous foam solution into a stable fine foam and the water into fine drops.

Jan 1, 1978

By Basil Dimitriades

The roles of hydrocarbons and nitrogen oxides in smog formation were investigated by the Bureau of Mines. Samples of automobile exhaust with varying HC and NOx levels were irradiated in a smog chamber under conditions that resulted in smog levels similar to those observed in the atmosphere. Results were used to define the patterns that describe the dependence of a number of smog manifestations on HC and on NOx. Using these dependence data and some simplifying assumptions, estimates were made of the ranges within which HC and NOx must lie in order to obtain specified levels of air quality.

Jan 1, 1970

By C. D. Messelt

The Bureau of Mines investigated the application of a diffusion model to sintering rate data developed for lithium titanium ferrite. The data were obtained by sintering pressed pellets under identical conditions for various times up to 11 hours. Stereological measurements were made on polished sections, and sintering rates were calculated. A model for intermediate stage sintering was fitted to the stereological data. This procedure produced a method by which these type data could be used to study the relative importance of volume and grain-boundary diffusion under a variety of sintering conditions.

Jan 1, 1979

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crushed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summaries of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling at the same group of quarries. OBJECT Or STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By Oliver C. Fursman

The Bureau of Mines undertook this investigation in order to determine the feasibility of producing commercially acceptable alumina and iron by application of the Pedersen process to high-silica, high-titania, ferruginous bauxites of the Pacific Northwest. Calcium aluminate slags were produced by smelting bauxite with coke and lime in an electric-arc furnace. Over 90 percent of the total alumina can be extracted by sodium carbonate solution from slags of properly controlled ternary-phase composition (CaO-Al203-SiO2) that are cooled slowly enough to permit adequate crystallization of the 2CaO-SiO2 and the calcium aluminate compounds. Most of the iron charged was recovered in the regulus; the slag contained about 2 percent iron (as iron oxide), regardless of smelting time.

Jan 1, 1968

By John M. Devine

The severe corrosion of equipment that is caused by the presence of hydrogen sulphide in oil and gas has been described in detail by several authors.5 Such corrosion, termed "low-temperature hydrogen sulphide corrosion", presents a somewhat different problem from the "high-temperature hydrogen sulphide corrosion" that is encountered in refinery operation and

Jan 1, 1932

[Determine how subsidence resulting from underground coal mining affects surface structures, and evaluate the usefulness s of the tiltmeter for monitoring foundation movement. Approach The Bureau of Mines is studying foundation response to mine subsidence in order to determine how subsidence-induced ground movements affect foundations in place directly above the mint. These investigations are essential if economic mitigation and repair techniques are to be made. In addition, commercially available tiltmeter are being evaluated (or use as a cost-effective monitoring technique. To study foundation response and to evaluate the tiltmeter system, full-scale model foundations were constructed, instrumented, and monitored for three years. Vertical and horizontal displacements, tilt magnitudes and directions, and observed damages were recorded. Displacements were compared with measured lilt to determine if the tiltmeter was tracking foundation response to subsidence, The Bureau developed a computer software package to aid in the reduction and analysis of the tiltmeter data.]

Jan 1, 1988

By E. P. Ferrero

Crude oils from fields throughout the world are analyzed by the Bureau of Mines to determine the characteristics of the oils and their contribution to the petroleum resources of the world. Analyses are reported for 169 foreign crude oil samples from 122 oilfields in Africa, Asia, Australia, the Caribbean, Europe, North America, and South America. Tables show the geographic and geo- logic origin of the samples, names of companies that supplied the samples, annual production for the fields, general characteristics and analytical and computed data, hydrocarbon-type data, cumulative production of the larger fields, and references to sources of geological and field development information. The analyses were made by the Bureau of Mines routine method and comparisons may be made with more than 8,000 other such analyses.

Jan 1, 1972

Phase I of U.S. Bureau of Mines contract H01220S3, "Improved Sensors and Fire Control Systems for Mining Equipment, II was an investigative effort involving study of the fire problem and preliminary design of a fire protection system. Overall contract objectives included three basic efforts: * Identify problems * Develop a design * Demonstrate a system The first two efforts were conducted during the period June through November, 1972. Phase II will involve testing of system components; construction and testing of a mockup; and demonstration of the system on a truck to prove its effectiveness under actual operational and environmental conditions.

Jan 1, 1972

By Robert W. Decker

This report presents a survey of published novel coal cutting (mining) concepts and a brief discussion of each one. A preliminary evaluation follows which identifies promising concepts, emphasizing reduced dust generation and economic production potentials. The promising concepts are then studied more deeply and evaluated in more detail with recommendations given for further development action. The concepts recommended for further work include: Roan and Pillar Mining: Deep Cutting Continuous Miner Linear Cutting Rotary Head Miner Longwall Mining: Oscillating Continuous Water Jet Miner Deep Cutting Shearer

Jan 1, 1981

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rim. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

By John Nagy, Hylton R. Brown, Irving Hartman

"INTRODUCTION The tests described in this publication were planned to provide information on the explosibility of metal-powder dust clouds. This subject has become increasingly important because of the large quantity and variety of metallic powders now used for military and industrial purposes. To provide the increased amounts of metallic powders needed in the manufacture of munitions and to supply the demand created by the rapid growth of powder metallurgy, existing metal-powder plants have been enlarged, production schedules accelerated, and new plants erected. In some cases new methods of producing metal powders have been developed. This increased production and the development of new manufacturing methods have caused an increase in the number of metal-powder fires and explosions, with accompanying heavy loss of life and property. These have emphasized the need for information on methods of providing protection against hazards inherent in the production and handling of powdered metals. This paper gives results of laboratory inflammability and explosibility tests made to April 1, 1943, and is a progress report. Many descriptive details have been omitted purposely; they will supplied in a later publication, expected to be a Bureau of Mines bulletin."

Oct 1, 1943