Search Documents

By Philemon Desrochers, Ken Qian Liu

Following the success of the West Ore Zone distress mass blast in 2001 at Brunswick Mine, a similar approach was taken to distress the North Regional Pillar (NRP) which contained over 3 million tonnes of high grade ore. The NRP is located on the 1000 m Level with very poor hanging-wall (H/W) rock mass qualities. After an extensive geotechnical review, the distress slot is located close to the foot-wall (F/W) of the NRP in order to have the competent ore as H/W. The longitudinal area to distress covers 115 m along the strike and 85 m high from 1000 1-sub to 850 Sill. Prior to the final mass blast, 3 voids were created to allow rock swelling: the North void, the South void and the trench just below the mass blast. After over one year of preparation, the mass blast of 202,000 tonnes was successfully initiated on February 7, 2003 with 1561 electronic detonators and 210,000 kg of emulsion explosives. The blast achieved its objective of distressing the NRP as indicated the mine-wide micro-seismic monitoring system. This paper describes different stages of the project from void preparation to the mass blast itself, as well as some detailed aspects such as muck-pile prediction for mucking sequence with the help of DMC_Blast simulation code and electronic detonators.

Jan 1, 2004

By Kerina Taylor

Due to their high amount of stored energy, explosives have been the cause of many serious injuries and fatalities over the last centuries. Despite safety advances and awareness in the last decades, injuries and fatalities continue to occur at mining operations due to blasting. According to the National Institute for Occupational Safety and Health, from 1978 to 2001, blasting incidents claimed 106 lives and were responsible for over 1000 injuries in mines in the US. The main causes of incidents found today are flyrock, blast area security and premature detonations. The concerted efforts of the mining and explosives industries and labour and government agencies have greatly improved the safety record of blasting in mines.

Jan 1, 2011

By C. Yi, D. Johansson, C. San Miguel, M. Wimmer

Sublevel caving (SLC) is a mass mining method based upon the utilization of gravity flow of blasted ore and caved waste rock. Production blasting has significant impact on the efficiency and productivity of SLC output, affecting material fragmentation, flow and recovery. Misfires could occur during blasting in SLC, which results in the loss of explosives and poor fragmentation. Usually, the blastholes are top-initiated with redundant lower primers set at + 25 ms as a precaution. If the top primers fail, the lower primers may initiate the explosive, which will induce out-of-sequence delays that can influence fragmentation and gravity flow. This work investigated the impact of misfires and out-ofsequence delays on fragmentation and gravity flow through numerical simulations using a coupled finite element and discrete element method. Different scenarios of misfires and out-of-sequence delays were studied, and the fragment size distribution was obtained to evaluate the blasting performance. The material flow behaviour was investigated to assess the gravity flow process. The results indicated that misfires significantly affect the fragmentation and the gravity flow process while the effects of out-of-sequence delays are not so significant for the investigated cases

Jan 1, 2024

By Walter Valery, Sarma Kanchibotla

Due to the global financial crisis, the world economy has turned upside down and most major economies in the world are facing severe recession for the past one and half year. During this period most commodity prices have tumbled by more than half from their peaks and such a sudden and severe economic downturn is not seen since the great depression. This sudden drop in commodity prices and lack of credit made many mining operations unviable and even those mines that are marginally viable at this point are operating under severe cost pressures and capital expenditure restrictions.

Jan 1, 2010

By Stewart A. Silling, D. Lynn Gordon, C. Mick Lownds, Dale S. Preece, Ali Bhuiyan, Patrick R. Bowden

Blast heave modeling and prediction utilizing the new discrete element model, GEM, that treats rock as elements with alternating arcs and line. Explosive loading of GEM elements is accomplished by utilizing the Noble-Abel equation of state to track the gas pressure from detonation through expansion to atmospheric pressure.

Feb 1, 2020

By J E. (Boet) Coetzee

SAFEX International, as the name suggests, is a global organisation, which has the fundamental objective of improving the safety of operations concerned with the manufacture, storage, transport, and use of commercial and military explosives and pyrotechnic products throughout the world. It is a nonprofit making organisation of manufacturers of explosives from all parts of the world, founded in 1954 with the aim of exchanging experiences within the explosives industry. Every third year SAFEX organises a Congress during which members present papers on selected themes and discuss reports of significant incidents that occurred since the previous Congress. Admission is for SAFEX members only, thereby creating a safe environment for discussing problems “within the family”. The XV Congress will celebrate the Association’s 50th anniversary in Geneva where it was founded. An overview of the Congress indicates its structure and covers aspects such as the training event, technical seminars and the themes for the plenary sessions and associated workshops. The paper also highlights the special event for the chief executives of member companies and the review of incidents that occurred in the industry since the last Congress. The Congress concludes with a social programme for delegates and their partners on the last day.

Jan 1, 2005

By S. Behera, K. Dey

This paper presents a methodology for finite element (FE) modelling to analyse the total deformation of rockmass under blast-load, with a focus on predicting backbreak that may occur during surface blasting operations. Backbreak can result from improper use of explosive energy, leading to damage beyond the excavation zone and jeopardizing operational safety and productivity. The paper highlights the impacts of backbreak on bench stability, excavator operation, drilling operation, flyrock generation, and improper fragmentation and boulder formation in surface blasting. However, prior estimation of extent of rock breakage zone can provide an idea to formulate the blast design to control the backbreak. While vibration-based prediction models are commonly used to estimate backbreak, they require physical blasting experimentation. To overcome this limitation, the paper describes the development of a FE model using ANSYS Explicit dynamics, which simulates rock blasting and calculates the total deformation of the rockmass. The rockmass deformation is modelled using Drucker-Prager (D-P) strength model with the Jones-Wilkins-Lee (JWL) equation of state for the explosives. The accuracy of the FE model is evaluated through physical experiments, and the results are compared with the vibration models. The FE model demonstrates close proximity to physical observations as well as vibration model result in predicting backbreak, thereby offering a promising alternative to vibration-based prediction models. The primary objective of the study is to predict the response of the insitu rockmass to explosive blast loading and determine the effective rock breakage zone.

Jan 1, 2024

By Brian Sandhuas, Robert McClure

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009, one North American Quarry and Construction Business experienced a series of flyrock incidents. In the spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

By Jean-Francois Lagueux, Andre Pomerleau

Goldex Mine is an underground mine located near the town of Val-d’Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long holes stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23.0 M tonne (25.3 M ton) of ore, large blasts up to 1.8 M tonne (2.0 M ton) are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km (0.62 mile) radius of the mine site.

Jan 1, 2011

By Kia Riihioja, Mike Higgins

A major difference between electronic and pyrotechnic detonators is that, in almost all but the simplest of blast layouts, computer software is required to plan a blast using electronic detonators. While it may be possible to program delay times without software, using only the manufacturer’s control hardware, the full potential of electronic detonators can only be realized through software. Until recently, the only software available has been provided by the suppliers of the electronic detonators. These usually have just enough features to create a hole layout and to assign times to the detonators in the holes. The software is also able to communicate only with the manufacturer’s detonators. This means that the client may be compelled to change several parts of the blasting process when a different delay system is adopted, from design through to implementation and reporting, even though these may be sub-optimal at the client’s mine. While many authors have demonstrated improvements in blasting outcomes using electronic detonators, very few have discussed how the delay times were calculated. Where the calculations are discussed, it is also obvious that the delay times must be monitored and re-evaluated as conditions in the mine change. For example, the principles of superposition and scaled distance, burden relief and energy cooperation between holes should be checked constantly for different locations within the mine, changes in rock properties, or even for differences between design and actual hole positions. The most common methods in blast design software to calculate delay times are inter-hole interval, relief contour and direct editing. Although they are simple in concept, they can result in fundamental errors if they are not applied correctly. The software for electronic blast designs should be capable of not just a timing calculation, but also of showing, to some degree, the impact and interaction of the calculated times.

Jan 1, 2004

By Abraham Lindo

Taboguilla is a small island located 10 miles outside the Panama Canal Pacific Entrance. In 2002 a fuel distribution facility was installed in order to supply fuel to vessels passing thru the canal. The current capacity of the tank farm is equivalent to 1,100,000 barrels. The demand for marine diesel at this location still exceeds the current capacity, thus an expansion project is currently underway to increase the available space for diesel tanks. There is a total of 800,000 cubic meters to be excavated in order to create the new space. 400,000 cubic meters of that total is basalt rock which will need to be blasted

Jan 1, 2011

By John Vynne

BHP’s Navajo coal mine installed drill monitoring and high precision navigation systems on their three overburden drills during 2002 and 2003. Details of the DrillNav system hardware and reporting system will be discussed, as well as the significant benefits Navajo has achieved since the systems were installed. Navajo is not satisfied with the current results and plan additional upgrades to the systems. In addition, Navajo plan to integrate the data from their drill systems with data from other systems to achieve even greater increases in drill productivity and to reduce overall mining costs.

Jan 1, 2007

By Gregory Hempen, Thomas Keevin, Russell Wilcox, William Wild

The Department of Defense Strategic Environmental Research & Development Program (SERDP) awarded funding for evaluation of procedures to mitigate peak pressures and energy flux density in the water column from ordnance being detonated on the ocean floor. The research purpose was to conduct scaled testing to resolve whether a theoretically-viable covering technology was operationally effective in reducing blast effects and the impacts of shrapnel. An additional objective was testing effectiveness of this method for hard-bottom units (rock or coral) and (unconsolidated) sediment substrate.

Jan 1, 2011

By Darío Innamorati, Jorge Oliva

Cerro Vanguardia is a known gold and silver deposit located in the province of Santa Cruz, Argentina. The mine has been in operation since 1998 and is thought to be one of the most important mines in Patagonia. More than 102 epithermal quartz veins have been identified in the area, with variable lengths, thicknesses, orientations and dips that constitute what is possibly one of the most extensive outcropping vein systems on earth. Veins are vertical and have variable depth. For this reason, the deposit is currently mined with a variety of extraction methods. This operation is made up of more than 60 open pits and 20 underground access ramps to exploit the deepest high grade narrow veins. This study is focused on the combination of underground exploitation with open pit blasting. That is, those production stopes in the upper levels of underground mines and their interaction with the damage levels in the final slope of open pit mines, as well as in the study of the impact of the generation of vibrations from the blasting of open pit mines and their influence on underground mines. Considering the current stage of the mine, after 20 years of operation, Cerro Vanguardia faces the need to mine deeper deposits in the face of increasing costs and declining grades. For this reason, it is essential to study the interaction of these exploitations. From a personnel safety point of view, this interaction must be well coordinated so as not to affect people and equipment. Likewise, the generation of vibrations due to blasting must be studied, which would produce new cracks, potentially generating overbreak and dilution. The main objective of this study is to determine the possible causes and influences of the blasting interaction in open pit and underground mines, seeking an optimization of the blasting process and a safety standard for personnel and equipment. To achieve these goals, this study includes a vibration monitoring plan to analyze the charge performance and determine rock constants. With the use of specialized software, damage modelling and simulations are used to determine values of damage in order to reduce overbreak. In addition, this plan contemplates the estimation of flyrock in blasting where underground work is connected to the surface, determining safety distances when carrying out a blast.

Jan 21, 2025

By Johan Gjødvad, Catherine Aimone-Martin, Charles Dowding, Mathias Jern

A residential structure adjacent to a quarry in Ohio was instrumented to record structure motions, resulting wall strains and existing crack displacements in response to close-in blasting within 82 m (270 ft). The project is a cooperative effort among international experts representing the European Federation of Explosives Engineers (EFEE) and ISEE supported by more than 21 persons from eight different countries to compliment prior work performed at the Aitik Mine in northern Sweden. The focus of this study is to compare blast-induced vibration measurements relative to regulatory compliance limits as a percentage of allowable velocities among eight different countries for a one-story residential wood-frame structure with a brick-and-mortar exterior and full basement. Participating counties included Austria, France, Germany, Norway, Sweden, Switzerland, the United Kingdom (UK) and the United States (US). Geophones were placed on the foundation and in the ground in accordance with each country’s regulations to record peak velocities as a function of frequency or distance to blasting. This study extends the work performed at the Aitik Mine to include interior corner geophones to calculate global wall strains and micro-m (micro-in) displacement gauges mounted over an existing drywall crack to measure blast-induced dynamic crack responses and climatological influences on daily opening and closing of a crack. Structure responses were documented for 68 blasts conducted north of the structure from February through September 2023 of which 17 blasts were selected for detailed analyses. The highest in-ground PPVs recorded were 43 mm/s and 59 mm/s at the NE and SW corners, respectively. Measurements from these blasts plotted within each country’s limits provided a comparison of stringency among the counties. The percentage of compliance limits among counties ranged from an average of 114% for the US, UK, and Austria limits to the highest of 585% for Switzerland. Despite these high percentages of compliance for all countries, the global tensile strains induced by these blasts were at most only 12 μ-strains and occurred with the highest velocity blast that exceeded each county’s limit. This high percentage of compliance and low strain level demonstrates the restrictive nature of the regulations studied. Peak dynamic crack opening and closing during blasting averaged 20 -m (0.0008 in) while the 12-hour weather-induced crack displacement during the time period over which blasting occurred averaged 200 -m (0.008 in) and the largest 12-hr change in crack width was 356 -m. This low level of crack response validates the observation that the studied regulations have highly conservative limits for cracking potential of standard building materials.

Jan 21, 2025

By Mark Spaniel

Computer 3D modeling to evaluate the potential underground blasting fragmentation performance based on rock within calculated damage radii along drillholes, as well as the burden distance from explosives along each drillhole. The results estimated from the 3D computer models closely predicted results found in the real world testing.

Feb 1, 2020

By Kunihisa Katsuyama, Yuji Ogata, Takuya Taguchi, Toshinori Arikiri, Yuji Wada, Kiyoshi Hashizume

The impact sensitivity of hot emulsion matrices was examined to investigate the safety assessment in the emulsifying equipment which forms the emulsion matrix in a water-in-oil type emulsion explosive. The sensitivity could not be evaluated by the small fallhammer test device commonly used in Japan. Therefore, a large fallhammer test device was used. It was confirmed that an explosion, a decomposition, or a no-reaction took place according to the degree of the impact. When a decomposition took place in the hot emulsion matrix, the behavior of it was investigated further by a DDT test. It was found that a decomposition, or a no-reaction occurred according to the degree of confinement.

Jan 1, 1997

By Paulo C. Fernández A, Sergio Matamala V, Claudio C. Gajardo, Christian A. Rees P

In fragmentation processes in open-pit mining, it has been observed that there are many opportunities for improvement if greater control of ore displacement in blasting is achieved, reducing the percentage of mixing between ore and waste material (dilution) through the integration of new technologies that allow its quantification and optimization of extraction polygons. This work investigates the relevance of the initiation sequence and direction of displacement in blasting in relation to ore dilution and the potential benefits of process optimization. A three-dimensional modeling tool was used to evaluate movement control optimizing the extraction zone based on the maximization of ore recovery. The study was made by iterating different scenarios, by varying only the initiation sequence and inter-hole delays. To validate the displacement simulation, a total of 10 blasts were carried out for calibration, obtaining a level of agreement between the simulation surface and the actual topographic survey of 80% or higher. The analysis included horizontal and vertical displacement, quantification of swell and dilution within extraction polygons for different scenarios, and informed decision-making based on ore control. The results clearly indicate that by modifying the blast initiation sequence, greater control over dilution in ore/waste transition areas is achieved, thus optimizing the recovery of the planned material and maximizing the ore grade. The use of this type of simulation tools allows for the generation of extraction strategies based on the value of the polygon, unnecessary displacements in the free face, optimal loading fronts, etc., maximizing the recovery of ore and stockpile material, complying with the planned tonnage and ore grade for each extraction polygon, delivering added value to the chain and emphasizing the importance of adding new technologies to the mining industry that allow for the optimization of processes to maximize profits.

Jan 26, 2026

By Matt Brandon

This case study demonstrates how integrating drone and GPS surveying with 3D modeling software creates more effective blast designs that address specific geotechnical challenges while improving safety and blast performance. In this case study an 80ft (25m) highwall experienced recurring slip plane failures exacerbated by a previously mined 40ft (12m) bench that removed back support, creating an unstable triangular rock mass. Previous blasting along this wall displaced the upper 40ft (12m) of material, opening geological discontinuities and causing progressive slope failures that compromised crew safety and blast effectiveness. High-resolution drone photogrammetry, GPS surveying, and laser measurements were employed to precisely map slip planes, bedding planes, and fault structures within the bench geometry. These geological features were imported into 3D design software to develop a shot pattern that strategically utilizes natural rock discontinuities rather than working against them. GPS-guided hole placement ensured accurate field implementation, while marking geological features on the surface of the bench provided visual references for the blast crew. The final blast design positioned the last row of holes to break preferentially along an existing slip plane while avoiding intersecting the next slip plane behind the blast. Explosive loading and timing sequences were adjusted based on the hole location relative to the 3D geological model to optimize fragmentation while maintaining wall stability. The optimized design improved highwall stability significantly, by reducing the slip plane failure mechanism that had previously compromised operations. Measurable improvements included enhanced highwall stability, reduced back-break, improved blast performance, and reduced safety risks for equipment operators and blast crews. Two subsequent shots using identical methodology were able to remove the rest of this problem area, confirming the repeatability and effectiveness of this integrated approach. This methodology demonstrates practical integration of surveying technologies with geological understanding to solve complex blasting challenges. Accurate 3D modeling of geological features enables blast designers to work with natural rock structures rather than against them, resulting in safer, more effective blasting practices. This case study shows the value of understanding the precise locations of geological features for optimizing blast design and provides a replicable process for addressing geotechnical challenges in blasting operations.

Jan 26, 2026

By Cesar Guerra, Alejandro Rojas, Dr. Jhon Silva, Luis Velasquez

The ANN method is applied to predict the P_80 size in one open pit gold mine in Peru. The ANN was implemented in Matlab programming language, and the results from the ANN are compared with data obtained using photo-fragmentation analysis software.

Feb 1, 2020