Search Documents

By Robert B. Hopler

This paper reviews, from the historical standpoint, the development of the commonly-used terms such as "No. 6 and No. 8" with regard to detonator strengths. The origin of the strength terminology is reviewed, and the many methods developed to compare the strength of one detonator to another are described, with the good and bad points of each method outlined. The "miniature cartridge test," very highly regarded by both the U.S. Bureau of Mines and Institute of Makers of Explosives in the 1930's and early 1940's, is described in detail, as is a test developed and used by IRECO.

Jan 1, 1992

By David Leidel, James Stuart

The 50 ohm resistorized electric detonator is commonly used in the oilfield for initiation of wireline conveyed perforating guns and other downhole explosive tools. This type of electric detonator provides some degree of safety above that of the conventional one ohm electric detonator, since a higher current level is required to initiate the device. In order to obtain the necessary data to develop safe distance tables from RF sources for the 50 ohm electric detonator, laboratory tests were conducted to determine the detonator’s “no-fire” current, AC impedance, and its susceptibility to ESD. The results were surprising as two types of failure modes were observed. The “no-fire’ current levels determined from Langlie “One-Shot” Test Methods were determined for the devices tested providing values for the 0.999 probability “no-fire” power level at a 95% confidence level. This data will serve as the basis for sets of safe distance tables from RF sources that will appear in the forthcoming edition of the Institute of Makers of Explosives Safety Library Publication 20, “Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators, (Blasting Caps)”.

Jan 1, 2010

By William Gates, Gabe McClain, Thomas Pallua, Joe Schrank

The Tennessee Capitol Corridor connects the Cordell Hull Building (CHB) to the State Capitol, which isa 232-foot-by-124-foot (71 x 38 m) structure in Nashville that includes porticoes built from local massive limestone. This connection was affected by the Capitol Connector Pedestrian Tunnel (CCPT) project, which is part of the overall Cordell Hull State Office Building and Central Services Demolition, New Construction and Renovation Project (Cordell Hull Renovation Project). To construct this connection, the two existing elevator shafts and a new emergency stairwell in the State Capitol were extended down to anew lobby area—the elevators by about 50 feet (15.2 m) and the stairwell by about 60 feet (18.3 m). This lobby was connected to the CHB by a 435-foot-long (133 m) pedestrian tunnel. It was predicted that most of the tunnel would be excavated in a relatively strong limestone; therefore, considering the project features and constraints, drill-and-blast techniques were selected as the primary excavation method. Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds. To calculate the ground response factor, the scaled distance of each shot was compared to the ground vibration as PPV, generating a subsequent regression curve with an R2value of about 0.7. Using the best fit curve equation, the estimated ground response factor was about 150 for the best fit line. Other than some cases with relatively high (> 2 in./sec [51 mm/sec]) recorded PPV values, the blasting operation was successfully conducted as planned and the observed strain on the monitored buildings was very low, mainly within ±2 με (0.0002% elongation). (In general, the recorded PPV was lower than 2 in./sec at frequencies of more than 50 Hz.). The strain gauges at key locations (cold joints and old fractures) in the Capitol and on other critical structures demonstrated strain was insignificant in relationship to ground vibrations from the blasting operations. The apparently small vibration-induced strains were related to the massive limestone construction of the Capitol and ancillary buildings, as the induced strain plus the existing strain did not exceed the critical strain of the massive structures.

By Gabe McClain, Thomas Pallua, Joe Schrank, William C. Gates

Because of restrictions on blasting in urban areas and, more importantly, the proximity of this construction to national historic landmarks, blasting operations were extensively monitored to measure and correlate ground vibrations as peak particle velocity (PPV), frequency, and strain—these being the major factors that would impact the surrounding buildings. As a result, copious amounts of data were gathered and interpreted within a short time to estimate blasting parameters and optimize the subsequent blast rounds

Feb 1, 2020

By Randall M. Wheeler

Pre-blast surveys are used to document the condition of a structure prior to the commencement of blasting activities. They provide the best means of determining the pre-existence of visible cracking and deterioration in a structure before blasting is initiated. A small investment in a good pre-blast survey, coupled with good public relations, could mean a large cost savings for a company in the future.

Jan 1, 1992

By Robert McClure, Carlton Lehman

Rendering safe explosives in an urban environment presents a unique challenge due to the safety concerns and disruption to the general public. Potential damage to the surrounding homes, businesses, utilities and transportation infrastructure are some of the major concerns when planning the render-safe operation. Engineering controls to mitigate blast effects, such as damaging air over pressure levels, material ejection and ground borne vibration, need to be implemented as part of the operation. Monitoring of seismic and air overpressure during these operations are needed to protect against potential claims when controlled or unplanned detonations occur.

Feb 1, 2020

By John Petty, John Loviza

As a blaster, have you ever had that uneasy feeing in the pit of your stomach as a codes enforcement official drives onto your jobsite? Have you ever needed an ally in a court of law against an unjust damage claim? Have you ever wished for a better and more open relationship with the guys who wear the badges?

Jan 1, 1996

By G. Adderley, Rob. Farnfield, L. Bermingham

The benefits of using electronic detonators within the drilling and blasting process in both surface and underground mining operations are well established and the use of this technology is widespread in the minerals industry. However, many users of such devices will also have experienced misfires where an electronic detonator has malfunctioned and shows evidence of damage from either transient shock or gas pressure. This is typically exhibited as a detonator shell that has collapsed causing damage to the internal electronic components before the detonator has initiated. Users often describe such detonators as being “shrink-wrapped”. The excavation of a misfire is always a hazardous operation, and it is better to minimize the risk of one happening in the first place. As part of a programme to improve understanding of this phenomenon and to allow a comparison between differing designs of detonators, a simple practical test was developed. This process involves the firing of a booster near electronic detonators in water. This paper describes this test work and draws some tentative conclusions on pressures for onset of damage with detonator shells made from different materials. The investigation has also yielded data showing that for some designs there is little difference between the pressure resulting in complete malfunction and sympathetic detonation

Jan 1, 2024

By Dr. Zach Agioutantis, Elliott Morgan

The explosives, mining, and heavy civil industries consistently battle the uncertainty that is associated with working with a heterogenous medium like rock in blasting. This has led to studies to increase fundamental understanding of material response under dynamic loading that is associated with blasting. This study looks at the dynamic strain associated with blasting the lab Split-Hopkinson Pressure Bar (SHPB) testing while also building off of previous studies with the goal of better understanding the dynamic forces that are enacted on a geologic body during a blast loading event. This is required in order to advance geologic blast response modeling. This is achieved through analyzing the stress and strain values for each specimen that are calculated from strain data collected with a SHPB. Based on this data, the dynamic material response characteristics are able to be determined. Tests were conducted on five Berea Sandstone specimens with a rough length to diameter ratio (L/D) of 1.0. The strain data from these tests were then used to create stress strain curves as well as charts depicting failure stress to both strain rate and failure particle velocities. The tests conducted returned similar results to previous tests results on Berea Sandstone while also showing a correlation between strain rate at failure and failure particle velocities. While further research is needed, there is evidence that SHPB test data could be used in conjunction with the MBF model. The MBF model states that the peak particle velocity (PPV) of blast vibrations can be correlated with deformation (strain) at a given point. With a further understanding of dynamic material response correlated to PPV measurements, further refinement could allow for better prediction of blast performance.

Jan 21, 2025

By Ali Kahriman, Olivio Angelini, Ibrahim Sefer, Burak Ekmen, Koray Arpak, Ertugrul Kaya, Yucel Karakus, Abdullah Sak, Aziz Ozdemir

In recent years, in order to bring solution to traffic intensity arising from transportation problems and facilitate public transportation in the modern world in paralel to urbanization and to the increase in population, it’s well known that, the construction of Access tunnels is inevitable. The driving of the tunnels is a subject of special interest in the technique of rock blasting. The essential factors in terms of tunnel driving and safety in tunnel blasting that is applied in metropolitan areas, an in depth knowledge of ground vibrations and the ways of reducing them to safer levels.

Jan 1, 2010

By Ashley Haslett

A European Directive on Identification & Traceability of explosives came into effect on the 4th of April 2008. This directive is intended to establish a harmonised system for the unique identification and traceability of all packaged explosives, detonators, reels of detonating cord and primers used in civil applications across the European Union. The directive must be adopted into the national legislation of each European Union member state by the 5th of April 2009 with compliance achieved throughout Europe by the 5th of April 2012. The requirements of the Directive apply to all explosives manufactured, used and imported into the European Union from 5th April 2012.

Jan 1, 2010

By Tristan Worsey, Jhon Silva

The paper discusses a limestone quarry case study that looks at change in fragmentation due to using different charge sequences when using the regular rhythmic timing method.

Feb 1, 2020

By ISEE

Micrometer Crack Response to Vibration and Weather, by Prof. Charles H. Dowding of Northwestern University, adds to Prof. Dowding’s already important contributions to the industry with his “Construction Vibrations” books. This new book reports and interprets important data on crack response that are essential for differentiating the unseen effect of weather on structural cracking from the usually much smaller effect of vibration. In addition, the book contains detailed descriptions of data collection methodology.

Jan 1, 2010

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is commonly adopted method in underground hard rock mining. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason being the unavailability of free faces as compared to open cast bench blasting. The geological and geotechnical parameters changes gradually even within the stope itself. So the blast design parameters should be planned according to the scenario of upcoming ring. Blast design parameters like burden, toe spacing, inclination of blast holes, diameter of blast holes, charge density of explosive etc plays an immense role in rock damage. For the proper breakage of rock, the movement of burden is prime objective. To study this, explicit dynamic based modeller of M/s Ansys was used. The burden values were varied from 20-65 times diameter to assess optimum burden value during the study. The models were simulated for the rock having 35 MPa uniaxial compressive strength and 102 mm blast hole diameter. Altogether three holes were blasted having hole depth 14-14.5m. The blast design parameters and respective blast induced ground vibration has been measured at the experimental site. Core sample of the rock of experimental site has been used for the evaluation of geotechnical parameters. These geotechnical parameters were inserted into the simulation model. The volume of rock excavated along free face has been calculated in each model. It has been found that the burden value can varies from 35-40 times blast hole diameter (3.6-4.1m) to achieve greater volume of rock along the free face for 102 mm blast hole diameter and rock of 35 MPa uniaxial compressive strength.

Feb 6, 2023

By Luis Huaroc, Augusto Sotomayor, Erick Rodriguez, Paulo Fernández, José Ricaldi, Luis Alejandro

The application of the Kuz-Ram model for the prediction of fragmentation is used worldwide, in Coimolache Mine it was used to determine blast domains and optimize the process by obtaining drilling patterns that meet a required X80 and reducing the uncertainty of drilling.

Feb 1, 2020

By B. Papilon

Dynamic pressures during blasting can affect performances of both electronic and non-electronic detonators. Boreholes can develop tremendous amount of pressures during blasting. The effect of such elevated pressure especially during electronic delay countdown is probably more acute in electronic detonators. Measuring the pressures during blasting can aid to understand the relationship between magnitude of the pressure developed and the multitude of blasting conditions.

Jan 1, 2013

By Sedat Esen

"This paper presents a critical review of the fragmentation data obtained from some large open pit copper and gold mines. Database ncludes 35 mines with Uniaxial Compressive Strength values ranging from 19 MPa to 227 MPa (2756 psi to 32923 psi). Variation in the fragmentation data and the causes are discussed in detail. Quality assurance/quality control (QA/QC) in drilling and blasting was shown to have significant impact on fragmentation. In addition, controllable blast design parameters including drill pattern, powder factor, blast timing, stemming length, etc as well as the large blast sizes havesignificant potential to improve fragmentation. Feed size requirements of crushing and grinding circuits were discussed in detail. The paper discusses the effects of different size fractions (top size, 80 %passing size and % passing 10 mm (0.5 in)) on the downstream processes and the role of the fragmentation model in the mine to mill process. Blast domains based on rock strength and structure canbe established by using a fragmentation model which is calibrated using measured fragmentation data. This allows the blast engineer to compensate for changing rock characteristics and stabilize the ROMfragmentation size and result in increased crusher and mill throughput. Two case studies were presented to demonstrate the benefits achieved in downstream processes. Main benefits were reduced downtime at crusher circuits, improved mill throughput as well as reduced total operating cost. A simple relationbetween uniaxial compressive strength and powder factor was proposed using the database for the optimized mines as a guideline to allow site engineers to compare their sites against the other sites."

Jan 1, 2017

By Bonifacio Degay, Mike Lovitt

PT Freeport Indonesia is a block cave mine that now utilizes an advanced undercut method to set up the min in the Deep Ore Zone (DOZ). In this method a slice of rock (undercut) is broken such that it sits on top of the drawbell level. The drawbells are developed to channel the broken ore into the extraction level and to enable the caving orebody to be drawn out in an even and controlled manner. These drawbells are difficult to form due to the small amount of void that can be developed in the low strength rock before firing. Starting with two rises of 2m square, the void ratio for the entire drawbell around 6%, which would normally result in a frozen and unproductive blast. Orica -Mining Services have worked with PT Freeport in a collaborative effort to find a solution to the mining problem. With excellent control of timing of the blasting it is possible to get fluid flow of blasted rock out of the draw points such that more void can be made available for blasting the remaining parts of the drawbell. The i-konTM electronic blasting system gives the exacting control of timing within the blast to achieve this Dynamic Void Generation (DVG). The solution stops the need to charge close to brows in the drawbells and reduces the cost and time related to developing initial blast voidage. This paper identifies the results of the trials including design, photographic evidence and vibration analysis. The flexibility and accurate timing of this electronic blasting system has enabled single hole initiation rather than 4 or more holes being initiated together, thereby reducing the damaging vibrations to the extraction level.

Jan 1, 2004

By Al Romphf

Managing blasting-induced air overpressure levels is a key compliance requirement for most blasting operations. Regression analysis, plotting overpressure amplitude vs cube root scaled distance, will often present a level of scatter which should be considered unacceptable. Relying solely on regression-based predictions can lead to overly conservative restrictions that may negatively impact other key performance indicators. Improved methods are needed for accurate overpressure prediction. The Heelan-Blair wavelet has been shown to closely resemble the overpressure waveshape produced when a single charge is fired under typical confinement conditions. The amplitude of a single-hole overpressure wave is influenced by factors such as proximity to the receiver, charge mass, orientation, and confinement both at the collar and face. Additional factors, including timing sequence, barrier effects, wind direction and velocity, must also be considered. The linear superposition method, commonly applied for ground vibration prediction, can be adapted for air overpressure modelling. In blast design software, this approach can consider all relevant parameters and environmental interactions. Given the uniform nature of air compared to rock, linear superposition using realistic elemental wavelets may replace the need to fire a signature hole. Data from 38 single-hole blasts conducted at quarries and mines throughout North America were used to develop and calibrate a linear superposition model. This model reasonably reproduces air overpressure results from full-scale production blasts, offering a practical approach to overpressure compliance and prediction.

Jan 26, 2026

By Adam T. Young

This paper will describe the process of using low density bulk emulsion as a means to maximize the production of an oversize or “rip rap” aggregate size range (8 inch to 72 inch) that the quarry customer has a market demand for. It will also discuss the pre-blast and post-blast metrics used during the product trials and evaluation.

Jan 1, 2017