Search Documents

By W. J. Birch, M. Kirke

Despite increasing competition from mechanical methods of tunnelling, the drill and blast method is often still the most viable method of excavating tunnels in strong and abrasive rock. To advance a tunnel using drill and blast, explosives are loaded into boreholes in the rock and detonated according to a prearranged sequence. On detonation of the explosive, the rock is fractured and displaced from its original position, leaving behind the desired void. Among the secondary effects of a tunnel blast are ground vibrations caused by elastic disturbances that propagate away from the blasted tunnel face. The possibility that such ground vibrations may cause permanent damage to property and substantial nuisance has generated significant opposition to the use of drill and blast, particularly in urban areas. It is therefore essential that the blasting engineer is able to predict Peak Particle Velocity (PPV) vibration levels at locations in the vicinity of the blast site. Such predictive capability enables the engineer to design blasts so as to ensure that ground vibrations can be kept within acceptable levels. The objective of this project was to analyse data obtained from the ground vibration monitoring program undertaken during the drill and blast excavation of a hard rock tunnel in Central England. Seismograph recordings of tunnel blasts contain a vast amount of information that cannot possibly be expressed using a single PPV value. The main focus of the study was to investigate whether predictive capability could be improved by using scaled distance models derived for selected PPV components relating to specific detonator timings in a given tunnel round. This study has established a method of analysis that can unlock this information for predictive purposes. By permitting the extraction of sub-event Peak Particle Velocity (PPV) values and allowing Scaled Distance (SD) models to be derived for individual period numbers or groups of period numbers, the method has the potential to vastly improve PPV prediction from tunnel blasting. The method established could also help diagnose blasting problems and help target blast design modifications, resulting in improved efficiency and excavation rates.

Jan 1, 2005

By M. Ramulu, A. K. Chakraborty, P. B. Sahu, C. Bandopadhyay, P. B. Choudhury

Human response to blast induced vibration and air overpressure is an unsolved problem that accompanies excavation process in mining. Pre-assessment and understanding of annoyance due to production blasting is probably one of the most important aspects of a successful mining operation. Complaints arising due to unoptimised blasts lead to various critical situations that hamper production. Inspite, this important aspect has been covered by a limited number of researchers in the world and probably least in Indian context. Human response is a complex phenomenon and the sensitivity of individual also vary from person to person depending on various factors like age, sex, literacy, health and exposure to mining. With ever increasing demand of minerals, opencast mines are expected to approach habitats and thus mine management may witness increased response to blasting. Many developed countries have their own guidelines based on scientific analysis, addressing such environmental problems, where as there are a few studies available in India. This study introspects above phenomenon in tune with mining requirements by analysing direct human response. This paper is based on a case study regarding the human response to blast induced hazards in a Manganese mine situated in central India. Advanced techniques of Critical Path Method and Multiple Response Analyses have been used to unearth important inferences on the response of different crosssections of population residing about the mine to blast induced noise, ground vibration and air overpressure. Various inferences drawn may provide guidelines to the planners, environment or safety departments and blasting official for safe and environment friendly blast design.

Jan 1, 2004

By Russell D. Melton, Gary A. Kanelos

A construction company performed blasting operations to break up limestone bedrock for excavation of residential basements. The owners of an existing residence located approximately 400 feet from the operation claimed that vibration damaged the structure and created foundation subsidence by lowering the moisture content of the foundation soils.

Jan 1, 1996

With the ever increasing problems of narrowing profit margins, and increased liability, a solution/option to SEE members is needed. It is essential that all members understand the benefits of utilizing explosives in combination with other methods of achieving the required result on difficult rock or concrete removal projects.

Jan 1, 1995

By Terra Dinamica, Frank Lucca

This paper discusses blast design for vibration control in tight construction blasting. Topics include blast pattern geometry, blast design formulas, loading, explosives & initiation selection, and utilizing borehole deviation equipment and lasers, and rules of thumb. The paper will also explore vibration prediction, neighbor relations, and related topics, such as blast plan submittal. Various projects from metropolitan construction blasting operations will be used as examples. Examples include blasting in the inner city, next to pipelines, and in housing developments.

Jan 1, 2005

By Mark Bauckman

Discussion Topics • Market Needs • Technology Developments & Best Practices • Industry & Government Developments • Future Possibilities & Your Role

Jan 1, 2006

By Douglas A. Anderson

The US Bureau of Mines, in RI 8507, has shown that blast vibrations at low frequency are more likely to cause damage and complaints than those at higher frequency. Since that publication in 1980, the Office of Surface Mining and many state and local regulatory authorities have incorporated frequency in their regulations for acceptable ground vibration from blasting. Even when frequency is not explicitly stated in regulations, it may become an issue in hearings or in court.

Jan 1, 1992

By : D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By Steve Dillingham

There are some blasters and blasting companies that just seem to have better safety reputations than others. This is in spite of the fact that they are essentially doing the same type of work under similar conditions. To achieve that enviable safety reputation, it simply comes down to a strong safety culture prompted by a responsibility for others, as well as yourself and your company.

Jan 1, 2003

By John Brown

Let’s talk about things that you, the driIl boss, the pit boss and the driller can do to eliminate the trend in drilling related accidents that have come to plague our industry in recent years. My paper will focus on reaI issues, problems and solutions that will affect our everyday outlook and attitudes about our jobs and lives. There are some real hard facts we must address if we are going to reverse this terrible killing trend.

Jan 1, 2000

By Rob Farnfield, Yuill Gavin

The rock blasting industry continues to be under pressure to reduce the level of vibration induced by the use of explosives. In recent years much research and development has been directed to minimizing vibration levels by controlling the delay period between blast holes. The most commonly applied technique is known as Linear Superposition. This technique takes the vibration produced from a single-hole test shot and simulates the vibration that would be produced from a full-scale production blast. The simulation can be run with various delay periods and the optimum delay chosen. The success of the Linear Superposition technique depends to a great extent on having accurate delay detonators and on the single-hole test shot reliably indicating the vibration signal produced from each hole in a production blast. A quarry-based case study is given illustrating how these assumptions are not always valid. In this case the use of electronic detonators has controlled frequency but not vibration level. The paper goes on to describe a series of single-hole test shots in an U.K. limestone quarry. The vibration 2 signals recorded are examined in terms of variations in free-face provision, blast geometry, explosive properties, etc.

Jan 1, 2001

By Steve Dillingham

In every aspect of conduct, on the blast site or off, the issue of credibility is raised. Promises are made, commitments are satisfied, safe practices are obeyed, communication is maintained, and proven procedures followed. Only by fulfilling these objectives, are we deemed trustworthy and reliable - in other words - credible. Unfortunately, at times, we fall short of achieving our goals. Whether intentionally or accidentally, everything is not completed according to plan or accuracy. On the blast site, falling short of achieving such goals may contribute significantly to a chain of events that can potentially produce accidents. At the very least, a blaster’s credibility will be jeopardized. The fact remains that the blaster that continuously conducts business in a professional manner will less likely find him or herself as a defendant in future claims.

Jan 1, 2003

By Felix Torres

CVRD is one of the largest mining companies in the world. Adoption of new technology and improving operational efficiency are top company priorities. Initiatives in these areas have driven continuous company growth and an increased share price. During the first half of 2001, the company had a net profit of nearly US$ 500 M.

Jan 1, 2003

By Jeff Peterson, Alastair Grogan

During the winter of 2001/2002, a number of seismic exploration projects were carried out in the Mackenzie River Delta area of the Northwest Territories, in Canada. The purpose of the seismic projects was to identify potential drilling targets for subsequent drilling programs, using explosives as a seismic source. Recent changes to fisheries regulations meant that blasting under lakes, the Mackenzie River and offshore from the delta, was not allowed to induce water overpressures in excess of 100 kPa in these water bodies, and that a water overpressure monitoring program had to be conducted to confirm that this requirement was being met. This paper describes the water overpressure monitoring program on one of the exploration projects, presents the results of the monitoring, and discusses the challenges of carrying out this work in the middle of an arctic winter.

Jan 1, 2003

By D. Swanson

Cold Detonation Physics (CDP) is a patented new field of explosives and the name for the explosive that is produced when non-toxic dry ice (frozen carbon dioxide) is combined with powdered metals such as magnesium and aluminum, which are non-toxic and nitrogen-free. The explosive is detonator-sensitive and detonates according to the rapid reduction of carbon dioxide back to carbon, which produces solids comprised mainly of metal oxides and about 5% carbon. CDP was determined to produce a maximum of 300 liters of carbon dioxide per kilogram (4.81 ft3 /lb) and about 1.5 liters of carbon monoxide per kilogram (0.024 ft3 /lb). Both these figures shift according to metal content where higher metal produces less gases. According to theoretical modelling, the relationship between static pressure and metal content was determined to be an inverse parabolic curve with optimum pressure at 25% to 31% metal, depending on the type/s of metal/s used. Velocity of Detonation (VOD) was determined by measuring light at the wavefront with fiber-optic cable inserted into a series of holes drilled into the side of a 3-inch diameter (76 mm) schedule 40 steel pipe containing the mixture. The highest VOD was observed at 25% magnesium and measured between 2,500 to 4,500 m/s (8202 to 14,764 ft/s) when initiated by a 454-gram (1-pound) booster and an electric detonator. A 25% 50:50 alloy of magnesium and aluminum sample shot at a higher velocity than magnesium, according to how the alloy generated smaller pieces of shrapnel when compared with shrapnel from a magnesium test. CDP, using 25% alloy, was tested for blasting limestone by drilling 3.5-inch holes (89 mm) and inserting a 3-inch x 4-foot cardboard tube (76 mm x 1.22 m) with the mixture, packed to a density of 0.62 g/cm3 . The blast was initiated with an electric detonator, behaved like ANFO with more energy and fractured rock sufficiently across the entire length of the borehole. Seismic analysis determined that CDP produces lower ground vibrations than traditional explosives.

Jan 1, 2024

By Stuart Brashear, Lee Schettler

The effect of water on several ANFO/emulsion blend ratios are documented by both physical observations and analytical testing to demonstrate the effect even small quantities of water can have on water resistant blends.

Jan 1, 1996

By Jeffery L. Dean

Founded in 1974, the ISEE has grown to more than 3600 members representing 72 countries. The Society and its 35 chapters in the US, Canada and Australia promote research and education, provide forums for the exchange of explosives technology, serve as a repository of explosives information, provide expert help to governments, conduct certificate/training programs, and promote the teaching of the safe and controlled use of explosives.

Jan 1, 1997

By Alan Jorgansen, Dave Hummer, Scott Scovira

Kennecott Energy's Colowyo Coal Mine is the largest open pit coal mine in Colorado and produces 5.5 MM tons per year. Colowyo uses the terrace mining method to recover up to seven seams of rolling coal ranging in thickness from 5 to 20 feet. Draglines are used to strip overburden ranging from 60 to 120 feet thick off two coal seams. These two seams are characterized by soft and fold fractured coal and in past practice cast blasting caused excessive coal damage. As a result, to ensure minimal coal damage and high coal recoveries, the overburden was excavated in two passes. The first pass removed the upper overburden to within 10 to 20 feet of the coal seam. The second pass removed the remaining overburden above the coal. Two-pass mining was effective in controlling coal damage, but also carried significant additional costs.

Jan 1, 2003

By C. Navalkar

Systematic drilling & blasting techniques are currently being viewed in the mining & construction industry as a correct 8z scientific approach for optimization process in rock excavation, as drill & blast costs usually represent major share in total cost of production and also the environmental impacts plays an important role in designing of the operations. Designing a blast is a complex planning task, which for optimization, includes deciding the bench geometry with respect to the rock properties & geology of the area, capacity of the excavators, choice of explosives & detonation method, tiring sequence, etc. Optimization of blast design needs a detailed comprehensive study of all the above intersecting elements. Preblast & Post blast surveys are required for further improvements in blast designs. However, the choice of blast design depends upon the the requisite blasting results opted for and the cost you are ready to pay for the same. The blasting operation, in general, also involves numerous side effects namely, ground vibrations, fly rocks, dust, noise & gas pollution, air blast effect etc. Again these effects can be made tolerable up to a certain extent depending upon the limitations of the environmental obligations as may be specified by the concerned authorities.

Jan 1, 2001

By Roberto Folchi

"This article deals with the excavation of a tunnel below the town of Isola LIRI, nearFrosinone, in central Italy. The tunnel was driven into a conglomerate formation, of lacustrine_fluvial origins, consisting in carbonate clasts with a sandy_silty matrix and calcitic cement. ""Drilling andblasting"" had to be adopted in place of a tunnel boring machine which had showeduneconomical performances. Good advance speed rates were achieved notwithstanding thepresence of some above structures to safeguard. The nearest structure (an old votivechapel) was less than 10 meters (33 ft.) far from the tunnel crown; the nearest residentialstructure was at about 15 m (49 ft.)."

Jan 1, 1993