Search Documents

By Adrian Moore, John Wilson, Alan Richards, Emad Gad

Project C9040 – ‘Structure Response to Blast Vibration’, funded by the Australian Coal Association Research Program (ACARP), involved the investigation of the structural response from blast vibration of three houses of brick veneer construction subject to a wide range of ground vibration levels. This paper summarises the findings of a house subject to vibration levels up to 220 mm/s (8.7 in/s). Damage attributable to blast vibration was not observed until vibration levels exceeded 70 mm/s (2.8 in/s).

Jan 1, 2003

By William Reisz

Over the years as surface mining operations have become more sophisticated, angle drilling has become a more popular blast design technique, especially in areas where overburden and stripping ratios have increased. Another method of blast design is the staggered pattern, which greatly improves explosives distribution within the blast. While both methods present some engineering challenges, this paper will discuss how the two methods can be combined to enhance fragmentation, improve cast percentage, drill production ratios and highwall control. A practical engineering approach will be presented as well as a discussion on the discipline required to maintain a quality blasting plan.

Jan 1, 2002

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine. Montana Technological University (Montana Tech) obtained a time-domain reflectometer (TDR) type VOD monitoring unit. Purchase of the VOD monitor was justified on verifying explosives performance used in Montana Tech’s practical underground mining class and provide a teaching aid for the school’s rock fragmentation class. Before demonstrating the unit to students, we figured we better learn how to use it first so we give the students an appropriate experience. Our first learning was in obtaining the correct coaxial cable for the VOD monitor and how to properly terminate the cable. Once the cable was on-site and terminated, VOD testing could commence. Use of the VOD monitor was tested underground in small diameter holes (1.5-inch, 38 millimeter) pneumatically loaded with ANFO. After a few failed trials, and follow-up discussions with the supplier, VOD readings were obtained for the ANFO loaded holes. Additional readings were obtained for a pre-split product and detonating cord to satisfy our curiosity that the unit was performing as specified by the manufacturer. This paper will share our learnings in the hopes that others can benefit.

By Shazad Hosein, William Birch, Douglas A. Anderson

This paper will present the results of tests of a new method for assessing explosive performance using wavelet transform analysis of standard blast seismograms. The theoretical background of the method was presented at an earlier ISEE conference.

Jan 1, 2015

By R. Franfield

This paper describes a situation that many drilling and blasting contractors have found themselves in – a client?s fear of the use of explosives. In the summer of 2007 Blasting Services Ltd was asked to undertake some drilling and blasting work in an abandoned quarry that was being restored for a housing development. Previous quarrying operations had left a series of overhangs that were considered unsafe and required removing. The site contractor considered that the best and safest way to carry out this work was by drilling and blasting. Blasting Services Ltd, with the technical assistance of Exchem Explosives, designed a drilling and blasting regime to accomplish this work with a series of trim blasts. The design took into account the close proximity of a structure in very poor condition and the imposed vibration limit of 6.0 mm/s (0.24 i.p.s.). The faces were profiled, holes drilled and explosives ordered. A few days before the first blast was due to be carried out the client decided that the poor condition of the nearby structure meant that the use of explosives could not be permitted. This decision was made despite the blast design indicating that the vibration level would be well below the 6.0 mm/s (0.24 i.p.s.) limit.

Jan 1, 2009

By M. Ganster, H. Krenn

The mission of the project is the fast and cost-effective rehabilitation of decommissioned lignite mining and coal upgrading facilities. This is necessary to ensure the successful future utilization of these sites. On the one hand, for founding new industrial and commercial facilities and on the other hand for touristic activities.

Jan 1, 2013

By Henry S. McDevitt

External Shock Mitigation (ESM) is being studied as a possible means of retrofitting existing buried structures to provide additional protection from ground shock. As part of this study, two tests were conducted on four ESM models and a control structure. The test articles were placed at a carrnon distance and subjected to the ground motions created by a buried explosive charge consisting of 2,ODO pounds of nitranethane (NM). Adequate instrumentation data were obtained to assess the response of the four ESM models. The assessment relied heavily on direct comparison of horizontal motions measured in the models, with similar measurements in the control structure. From the tests, it was observed that peak accelerations were reduced by a factor of 5 by the ESM. However, the particle velocities and displacements were not significantly affected by theEIS.

Jan 1, 1997

By Gregory Poole

With access to the World Wide Web, many resources are readily available for improving claim reports. With a little time spent on line, a more thorough report can be created. Claimants will accept the conclusions of a report more readily when they can view support information on their own computer, particularly when the support information is not just from blasting related web sites. Some suggested resources are discussed including aerial pictures, local tax maps, topographical maps and home repair web sites. This paper provides suggestions for tracking down support information on the web and information on how to properly reference this information. Case studies of several claim investigations are presented. These are some examples of how a little time spent online provided clear and convincing evidence to support the conclusions of the investigation.

Jan 1, 2006

By Thomas Hans Kleine

In general the software required by a blast designer includes tools that graphically present blast designs (surface & underground), can analyze a design or predict its result, and can assess blasting results. As computers develop and computer literacy continues to rise the development of and use of such tools will spread.

Jan 1, 1995

By Greg Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified geologically sensitive due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the geologically sensitive area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model.

Jan 1, 2018

By P D. "Takis" Katsabanis

The phenomenon of sympathetic detonations in blastholes is investigated by comparing experimental observations and numerical modelling results. Numerical modelling using the TDL computer code and Forest Fire decomposition rates for commercial explosives has shown the importance of blasthole diameter, impedance of the stemming and host rock. Comparison with experimental observations has also shown that sympathetic detonations cannot always be treated as shock to detonation transition. Examination of previous results which have been obtained from calibrated low amplitude shock experiments reveal that there is an ignition threshold prior to the detonation threshold. The difference between the two thresholds is more pronounced in the case of air bubble sensitized products. The ignition threshold can be very important under the confinement provided by the blasthole and the conditions of application. It also correlates well with the pressures expected at the gap distances of interest in the practical application. It is suggested that critical energies are used as the criterion for cross initiation in blastholes. Practical suggestions based on the numerical calculations and experiments based on these calculations are also given and discussed.

Jan 1, 1991

By Steve Colburn

The CRITERION Survey Systems utilize both theodolite mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environments characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, Windows-based, interactive software program which can be run on any standard PC.

Jan 1, 1997

By Adrian Moore, Alan Richards, Andrew Brodbeck

Structural blast vibration limits should be based on the strength of the structure, the stress induced by blasting, and a responsible factor of safety. In this paper a methodology that uses direct strain measurements to determine the stress induced by blasting is described. The methodology has been used to measure strain resulting from blasting, and establish appropriate blast vibration limits on a brick sewer tunnel, an underground mine heading, brick veneer houses, a water pipeline, and transmission tower foundations. An outline is given of the use of the methodology to establish limits for the main entry heading of an underground coal mine, and transmission tower footings. The methodology that is described has reduced uncertainty factors, and permitted the specification of higher blast vibration limits than had been previously used.

By Ron Frye, Carl Liibbe, Wayne Curtis, Julie Pecori, Dan Leach

Test work comparing the performance of a Low Density Porous Ammonium Nitrate Prill to regular Porous Ammonium Nitrate conducted in Pennsylvania and New York showed that less ammonium nitrate was required to perform the same work and that improved sensitization of an emulsion/ammonium nitrate blend reduced “orange fumes”. Fragmentation was similar in all tests with improved heave and throw experienced.

Jan 1, 1997

By Grigor Mishev, Georgi Petrov, Benjamin Cebrian

Before designing a single blast or all the blasts on a pit level, it is critical to assess the main goal on each. To do this, a series of constraints must be taken into account: wall protection, vibration control, flyrock hazards, fragmentation required, desired displacement as well as economy, equipment efficiency. The tool to do this is the Blast Master Plan. Many mines fail to integrate on its elaboration key stakeholders such as planning, operations, geology/geotechnical and milling departments. Designs not only have to provide consistent behavior of the blasts, but have to make sense all in one with the geological and geotechnical conditions as a starting point. Once blasts are designed under an organized set of priorities, and complemented with quality controls, optimization is possible on a large scale.

Jan 1, 2016

By J A. Singer, S R. Iverson, C A. Link

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in a mine face. Excavation blast damage can be as shallow as 1 to 2m and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m along mine walls. First arrival times from the seismic data were used to produce P-wave velocity tomograms. The tomograms show transition from low velocity zones to velocity associated with competent rock. We interpret the low velocity zones to indicate residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock. Our method can be applied efficiently in an underground environment to provide continuous velocity information with depth into a mine wall over a span of approximately 10m.

Jan 1, 2009

By Dale Preece, Ayman Tawadrous

This paper presents a number of examples of three-dimensional blast modeling in both surface and underground environments that include time-delay explosive decking. These examples include: 1) quarry blasting, 2) coal seam protection blasting, 3) mineral mine blasting with high energy time delayed decks, and, 4) underground single-level/single-shot drawbell blasting.

Jan 1, 2014

By Douglas Rudenko

Have you ever had a neighbor complain about a blast one day, but says the next day’s blast was better, even though the Peak Particle Velocity (PPV) increased? How about neighbors that complain about a small trimming shot, but don’t complain about a big production shot? Have you ever reduced the pounds/delay and gotten more complaints ? Mine operators are often bewildered when trying to correlate blast design parameters to homeowner complaints. When complaints come, standard practice is to set up a seismograph in the neighbor’s yard to monitor the blast. Immediately after the blast, the neighbor usually reappears from the house wanting to know the seismograph reading. When told that the PPV was 0.1 in/set, well below damage levels, the homeowner explodes saying “Your machine is wrong”. Perhaps he is right. Understanding why people complain about blasting is not about PPV, it’s all about structural response. People could care less about how much the ground vibrates; they only care about how much their house vibrates. In this paper we will examine the primary factors that control structural response. Through the use of a large array of digital seismographs, the effects of two production blasts on a community surrounding a quarry are studied. The predicted structural response resulting from each blast is calculated at 175 seismograph locations. The predicted response is then correlated to previous research on human perceptibility to vibrations. The results of this analysis and correlation give a better understanding of what the residents actually feel in their homes. The detonations of two single-hole signature blasts are also recorded by the array of seismographs revealing the dynamic characteristics of the geology ‘surrounding the quarry. Once the influence of the geology was understood, blasts were configured to disrupt the natural rhythm of the site through the use of millisecond delays.

Jan 1, 2000

By Noelia Valencia, Carlos Agreda, Jean Arenales, Juan Llerena

"In this technical paper is reported the several tests and the preliminary results that has been obtained so far. It must be emphasized that this investigation was started several months ago.On the other hand, it is known that acid water exists in some underground mining operations as well as in open pit mining operations all over the world. Taking into account this problem, our work teamdecided to carry out the present investigation. Therefore, it ensures a decrease in blasting costs avoiding this problem and as well as this, it allows to reducing fatal accidents that could occur caused by poor control of acid waters within mining operations."

Jan 1, 2016

By Alexandre Passos, Giorgio De Tomi, Tatiane Marin, Dennis Cremonese, Jacopo Seccatore

"In the mining industry, rock excavation is the first phase of the comminution process. Downstreamoperations such as secondary breaking, crushing and milling terminate the process, reducing the size of the grains down to the desired particle distribution. In such a cascade process, every process upstream heavily influences all the downstream operations. When rock excavation is carried out by drilling and blasting, a very economic source of energy (the explosive) is used at the utmost upstream; a more expensive source of energy (electricity) is employed for all the downstream phases. This means that managing the correct employ of the explosive energy is a form of managing the whole process, controlling the operational costs and therefore the profitability of the whole business. We simulated this cascade behavior, using as a starting point the experimental data obtained from small-scale block blasting, evaluating the influence of blasting on the grindability of the blasted material. This study showed the reduction in visible (particle size) and invisible fracturing (micro-cracking, resulting in a reduction of the Work Index WI). The particle size distribution for full-scale blasts was estimated by means of algorithm simulation, then we simulated the behavior of the comminution plant fed with the material possessing the characteristics previously estimated. All the costs (drilling, blasting, electric energy for the engines of the crushers and mill) were calculated and charted. The results show a clear curve that allows to estimate the minimum operating expenditure (OPEX) for the whole mine+plant framework. Being the WI dependent on the output on the blast, one can manage the performance and the expenditure of the whole comminution process by adjusting drilling and blasting parameters For any given mine, it is possible to perform a simulation and encounter the minimum OPEX scenario for the comminution process and managerial choices can be oriented accordingly. In a cascade productive chain as mining is, responsible strategic choices must be taken looking at the entire production framework. Compartmentalized managerial staff and budgets for separated production areas are not acceptable anymore. Somehow higher costs upstream can lead to effective decrease in costs and increase in efficiency and productivity of the processes downstream."

Jan 1, 2016