Search Documents

By S. K. Chaulya, R. S. Singh, B. B. Dhar

Two prominent local species, Dendrocalmus strictus (bamboo) and Saccharum spontaneum (kashi), and two exotic species, Cymbopogon citratus (lemon grass) and Vetiveria zizanoides (vetiver), were selected for growth trials on dumps at Mandaman, Chora, Mudidih, South Balanda and Ghugus. The climate at these sites is dry tropical and the surface soil layer a slightly acid to neutral sandy to clayey loam 10-11 cm thick, impoverished in major plant nutrients. After two years bamboo had grown the most, up to 325 cm in height, and contributed the greatest biomass, 638 g/m2 of plant. The local kashi species had a very good regenerative capacity, which was lacking in the lemon grass and vetiver. The grasses had very good soil-binding capacity and could also provide income if used as cash crops

Jun 21, 1905

By T. Bennett

Geothermal energy has the potential to provide 20% of the UK's annual average electricity generation capacity requirement. This article discusses the costs and potential benefits.

Jun 1, 2015

By R. Trueman, D. B. Tyler

Numerical modelling was used to determine the magnitude and direction of stresses around drives both adjacent to and distant from open stopes in the South Crofty tin mine. Modelling predicted that drives near the stopes are situated in a stress-relaxed zone. The peripheries of drives that are sited in solid rock away from the influence of stoping are in compression. Key-block modelling was used to determine the typical geometries of critical blocks and distinct element modelling was used to determine block stability. The conclusions derived from modelling fitted the observational data. This indicated that key-block theory is a valid tool for analysing the stability of roadways in the South Crofty mine. The support requirements for drives located next to stoped-out areas were formulated using a risk analysis approach to key-block formation. The results were compared with support guidelines derived using empirical design methods. Good agreement was obtained for the roofs of the drives but not for the sidewalls. The concept of a critical excavation width was formulated: once an excavation is larger than the critical size the length of rockbolts need not be increased as the excavtion dimensions increase. This may be the case in all rock mases.

Jan 4, 1993

By L. J. Barnes, R. O. Koch, J. H. Versteegh, P. J. H. Scheeren, F. J. Janssen

Following two years of laboratory research with bench scale reactors, a 9 m3 experimental process demonstration reactor was installed at Budelco's zinc refinery to treat their underlying groundwater. A 600-fold scale-up was successfully achieved. It has demonstrated that this anaerobic microbial process can remove a wide range of heavy metals and sulphate to the required levels. Extended operation of the demonstration unit has shown that the process is robust, can withstand wide variations in feed composition, rapidly recovers from operational upsets and is easy to start up and shut down. The metal sludge produced can be processed in a metal refinery to recover both metals and sulphur.

Jan 12, 1992

By L. Wade, R. Wang, M. A. Horton

Laboratory methods to find the mechanical properties of rock are inherently biased towards stronger strata, which best survive the sample preparation process. Geophysical techniques are not subject to such bias and may be used to predict mechanical properties rapidly and cheaply. Samples (151) were obtained from a borehole that had been comprehensively geophysically logged. The mechanical properties of the samples were established in the laboratory and correlated with the geophysical responses of the strata from which they came. The results indicate that, for homogeneous strata at least, it is possible to predict the unconfined compressive strength reasonably well from sonic travel time measurements made in the field. Predictions of static Young's modulus may also be made from this data source, but with a lesser degree of confidence. A multivariate regression equation is presented which relates down-hole sonic travel time to unconfined compressive strength, depth and the frequency of fractures in the rock mass. This equation may offer potential for the prediction of the mechanical rock properties of fractured and layered strata.

Jan 4, 1993

By J. H. E. Jeffes, K. T. Jacob

The activity coefficients of oxygen in liquid Pb-Sn alloys have been measured between 550 and 1100°C by use of solid oxide galvanic cells: Pt, Ni-NiO | Zr02 Solid electrolyte | O (Pb + Sn), Cermet, Pt; and Pt, Fe-FeO | Zr02 Solid electrolyte | 0(Pb + Sn), Cermet, Pt. Alcock and Richardson's quasi-chemical equation, with the coordination number of atoms set to 2, is found to predict successfully the activity coefficients of oxygen in these alloys. The relative partial molar enthalpy and entropy of oxygen at 1 atom per cent in the alloys have been calculated from the variation of the activity coefficient with temperature. The addition of Sn to an unsaturated solution of O in Pb is shown to decrease significantly both the partial molar enthalpy and entropy of O. As the measurements were restricted to a narrow range between 750 and 1100°C in Pb-rich alloys, however, the pronounced variation of the partial molar enthalpy of O with temperature at constant alloy composition predicted by the quasi-chemical model could not be verified.

Dec 1, 1971

By A. B. Holland-Batt

Two graphical techniques which are commonly used to assess batch separations are analysed in terms of reaction kinetics to provide a more powerful method of evaluation. An alternative and more general approach, based on the selection and application of suitable efficiency criteria, is also presented. The method proposed distinguishes between selection and collection efficiency in flotation and can be used to estimate the degree of liberation in the feed. Two examples are given: table concentration of monazite and ilmenite from a beach sand, and flotation of a pyrite-haematite ore

Dec 1, 1971

By D. Mireku-Gyimah, R. S. Suglo

Ghana contains auriferous belts which cover 51 800 km2 of its small area of 239 400 km2. From 1493 to 1600 35.5% of the world gold production was from the Gold Coast (renamed Ghana in 1957). This dropped to 8.9% from 1701-1800. For the past fifteen years annual production has averaged less than 2% of the world total. By 1985 only four gold mines were operating, compared with 45 in 1934 and 11 in 1945. Since 1987 Ghana has experienced a boom in gold mining activities. By 1991, 83 new companies had acquired prospecting licences. At least five new companies have started large-scale production. About 650 licensed small-scale mining groups are in operation. The economic and technological factors that have contributed to the decline of gold production in Ghana are discussed. A summary is given of the methods used to mine and recover gold. These cover small-scale workings, dredging, open cast operations and underground mining. The advantages and disadvantages of these technologies and the future of gold mining in Ghana are considered.

Jan 4, 1993

By R. W. Ruddle

The advent of new methods of roasting, “flash roasting and fluidisation”, which are now under development, combined with the use of oxygen-enriched air, may markedly increase the SO2 content of roaster smokes. Skogmo suggests that the production of smokes containing as much as 50 per cent SO2 should be feasible. The use of flash smelting processes may well enable a similar increase in the SO2 content of smelter smokes to be made. In this event the recovery of sulphur would be greatly cheapened and the process might well be much more economic, even if allowance is made for the cost of generating the oxygen

Jan 1, 1953

By A. Paulin, A. W. D. Hills

The work has shown that packed-bed behaviour can be predicted from the results of single-particle experiments, total reaction times being predicted somewhat more accurately than gas and solid temperatures and gas compositions. A small laboratory packed-bed reactor was built and used to study the decomposition of beds of specially prepared CaCO3 spheres, steps being taken to minimise the effects exerted by the walls of the bed on processes occurring within the bed. Gas and solid temperatures and gas compositions were measured at various points in the bed and compared with theoretical predictions based on kinetic data determined in previous single-particle experiments. The measured solid temperatures and total reaction times agreed remarkably well with the values predicted theoretically. Gas and solid temperatures measured after the reaction had finished at any point in the bed did not agree with the theory. This was because solid temperatures in the bed rose very rapidly once the reaction was completed and the walls of the bed could not be heated at a sufficient rate for their temperatures to rise as rapidly; thus some loss of heat from the bed to the walls was inevitable, and this could not be accounted for in the theory. In addition, the theory did not allow for the conduction of heat within the bed, and this resulted in some further slight discrepancy between the measured and predicted values, particularly after the reaction was completed. Gas compositions measured in the bed were rather scattered, but, even so, they agreed moderately well with the predictions of the theory.

Dec 1, 1971

By A. H. G. Mitchell

Gold-poor and gold-rich porphyry and epithermal gold-silver deposits of Caenozoic and Cretaceous age in the western Pacific and central and eastern Europe are confined to predominantly andesitic continental margins and island arcs. The arc volcanic rocks overlie a complex non-oceanic basement of stacked nappes, the uppermost of which is often ophiolitic. The emplacement of ophiolite triggered a reversal of tectonic polarity, subduction and arc magmatism. Andesitic volcanism and the formation of a strato-volcano were followed by the ascent of magma and porphyry copper mineralisation. Regional propylitic alteration came from convecting, predominantly meteoric fluids. Magmatic degassing caused advanced argillic alteration. This is commonly unmineralised in perched water tables, but may sometimes host high sulphidation gold or enargite gold at deeper levels within the propylitic zone. The onset of extensional stress after the andesitic volcanism allowed meteoric water to circulate to depths of 5 km or more, with consequent cooling of an ascending magma body at depth and the development of low sulphidation epithermal gold mineralisation near and immediately above the sub-volcanic basement surface. All andesitic arcs are mineralised. Regional controls on their ore potential include the level of erosion and geological features in the basement that focus the ascent of fluids. Differences between the mineralisation of the European and the western Pacific arcs may reflect the presence of older, more granitic basements in many of the European arcs.

Jan 12, 1992

By G. E. Pearse

Reports, discussions, a written contribution and two written replies are presented from 11 sessions on: Safety and compressed air; Ground movements; Geotechnical; Channel Tunnel (2 sessions); Machines; Case histories; Transport tunnels; Case studies; Site investigation; and Undersea tunnels

Jun 13, 1905

Summary of the morning's events with a Written Contribution to Paper No. 4 and author responses

Jan 1, 1947

By R. Scheepers, J. E. Misiewicz, A. C. Fitzgerald

Discussion by A.C. Fitzgerald of the paper, published in Trans. IMM A, vol.104, 1995, p.B121-B135, is presented together with the authors' response. Fitzgerald points out a number of problems with the idea of mineralising fluids leaving no trace in the large volumes of rock traversed before depositing all minerals of value in a particular horizon or rock type with which the required isobaric or isothermic surface also coincides. He suggested that in the case of the Rooiberg tin deposits, the Lebowa Granites may be batholiths that reached the surface and were capped by sheets of their own volcanics. The authors agree that they had considered a possible syngenetic origin for the stratabound deposits, explain that no conclusive evidence for this could be found, discuss the relative ages of the sediments and volcanics of the Rooiberg Fragment and explain the role of its low-intensity deformation and flat dip in the coincidence of an isobaric-isothermic surface with the lithological stratification

Jun 18, 1905

By R. Patel, J. Ephraim

The production of titanium dioxide (TiO2) from its minerals such as ilmenite is challenging, and subsequent isolation of titanium from TiO2 is even more difficult because of the metal-oxygen bond strength. Currently, titanium sponge is mainly produced via the Kroll process, which is energy intensive and generates large quantities of waste. A number of international research groups have come up with technologies for the production of titanium metal. However, none of them have been commercialised, because of engineering or economic issues. The team at Bradford have confirmed that ultra-pure titanium powders can be separated from TiO2 powder through metallothermic reduction and are working to scale up the process.

May 1, 2015

By M. A. Bussell, G. S. Camm

The study included lode zones at Wheal Pendarves, South Crofty and Rosevale tin mines. Fluid inclusion-containing microfractures are a common feature of the granites and typically show a preferred orientation over quite a large area. The close proximity of a dominant vein or fault controls their density and orientation. They are important pathways for fluids and provide a marker for palaeo-fluid flow. Overprinting provides a reliable representation of the evolution of the hydrothermal fluids in a vein system from early magmatic fluids to late-stage meteoric and basinal brine input. Measurement of microfracture orientation allows estimation of the regional stress regime during a specific hydrothermal event. Since micro- and macro-structures can generally be reliably correlated, these studies assist in modelling the detailed development of complex vein systems. Microfracture density is a good measure of palaeo-permeability, with implications for control of wallrock alteration. The determination of the location and density of microfractures can assist the mine geologist in identifying the location of potentially economic vein structures where macroscopic markers are absent

Aug 1, 1996

By K. El-Barawi, Hussein M. Kamal

Chlorination was performed of iron-rich chromite ore from Barramyia, United Arab Republic (UAR), together with its concentrate. The effects of change of grain size, chlorine gas flow rate, time and temperature were studied. The extent and mechanism of chlorination were followed through chemical and structural analyses of the feeds and complete chemical analysis of the chlorination products. By conducting the chlorination process for short periods at 600°C or lower temperatures, products having high Cr-Fe ratios suitable for ferrochrome production can be obtained.

Dec 1, 1971

By N. T. Moxon, D. Mead, S. B. Richardson

A laboratory and theoretical study of air decks was carried out to assess the effects of the size and location of air-decks on fragmentation. The degree of fragmentation was found to depend on both factors. As the size of the air-deck increases the degree of fragmentation is reduced relative to a full column charge. However, the reduction is relatively small until a critical size is exceeded. The critical size depends on the strength and structure of the surrounding material. A critical air-deck length of 30-35% of the original explosive column was determined for the model materials used in the study. A theoretical explanation of the results was derived based on pressure decay rate relationships. The location of the air-deck also influences fragmentation. The interaction and oscillation of the two shock fronts from the top and bottom charges mean that mid-column air-decks produce better fragmentation for the same air-deck length and explosive loading as top-column or bottom-column air-decks.

Jan 4, 1993

By C. A. Pickles, S. J. Splinter, J. Cameron

The addition of copper oxide to a borosilicate slag resulted in the breakdown of the silicate network and a dramatic decrease in viscosity. With increasing borax to silica ratio the viscosity was reduced by two mechanisms. First, rising sodium oxide content promoted cleavage of the Si-O bonds. Second, increasing boric oxide (B2O3) content increased the number of trigonal borate units that were converted to tetrahedral borate units by sodium oxide and copper oxide. The BO4(4-) tetrahedra decreased the local silicate symmetry, thus disrupting the silicate network and lowering the viscosity. The activation energy decreased with increasing temperature and increasing copper oxide content

Jun 13, 1905

By A. W. Fletcher

Report of discussion at February, 1971, IMM general meeting (Chairman: M. J, Cahalan President) of a paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, December, 1970, pp. C247-52, and contributed remarks. Contributions are included from: Cahalan M.J., giving figures related to leaching Cu from pyrite at Rio Tinto 1880-1910; Noakes F.D.L.; Embling P.M.K.; Bradshaw A.V.; Le Roux N.W.; Kelly D.P.; and Tuovinen O.H. Questions were raised regarding impurity removal, effects of light and ultraviolet light on the bacteria, the economics of solvent extraction and the possibilities for other organisms or other metals

Dec 1, 1971